[ Upstream commit b89fefda ]

spi-gpio is capable of dealing with active-high chip-selects.
Unfortunately, commit 4b859db2 ("spi: spi-gpio: add SPI_3WIRE
support") broke this by setting master->mode_bits, which overrides
the setting in the spi-bitbang code.  Fix this.

[Fixed a trivial conflict with SPI_3WIRE_HIZ support -- broonie]

Fixes: 4b859db2 ("spi: spi-gpio: add SPI_3WIRE support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b5179ec4 ]

VMs may show incorrect uptime and dmesg printk offsets on hypervisors with
unstable clock. The problem is produced when VM is rebooted without exiting
from qemu.

The fix is to calculate clock offset not only for stable clock but for
unstable clock as well, and use kvm_sched_clock_read() which substracts
the offset for both clocks.

This is safe, because pvclock_clocksource_read() does the right thing and
makes sure that clock always goes forward, so once offset is calculated
with unstable clock, we won't get new reads that are smaller than offset,
and thus won't get negative results.

Thank you Jon DeVree for helping to reproduce this issue.

Fixes: 857baa87 ("sched/clock: Enable sched clock early")
Cc: stable@vger.kernel.org
Reported-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 3941310c ]

Add one PCI ID for 9260 series.

CC: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ab27926d ]

The devices with PCI device ID 0x34F0 are part of the SoC and can be
combined with some different external RF modules.  The configuration
for these devices should reflect that, but are currently mixed up.  To
avoid confusion with discrete devices, add part of the firmware to be
used and the official name of the device to the cfg structs.

This is least reorganization possible (without messing things even
more) that could be done as a bugfix for this SoC.  Further
reorganization of this code will be done separately.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b513a18c ]

This is much louder then we want. VCPI allocation failures are quite
normal, since they will happen if any part of the modesetting process is
interrupted by removing the DP MST topology in question. So just print a
debugging message on VCPI failures instead.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: f479c0ba ("drm/nouveau/kms/nv50: initial support for DP 1.2 multi-stream")
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 906d2d3f ]

Since ccmp_pn is u8 *, the second half needs to start at array index 4
instead of 0. Fixes a connection stall after a certain amount of traffic

Fixes: 23405236 ("mt76: fix transmission of encrypted management frames")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 103cda6a ]

Exynos4212 and Exynos4412 have only four ADC channels so using
"samsung,exynos-adc-v1" compatible (for eight channels ADCv1) on them is
wrong.  Add a new compatible for Exynos4x12.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a9b0a2a7 ]

Add information about new compatible for S5PV210
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 882bf52f ]

S5PV210's ADC variant is almost the same as v1 except that it has 10
channels and doesn't require the pmu register
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 61c08aa9 ]

The vCPU-run asm blob does a manual comparison of a VMCS' launched
status to execute the correct VM-Enter instruction, i.e. VMLAUNCH vs.
VMRESUME.  The launched flag is a bool, which is a typedef of _Bool.
C99 does not define an exact size for _Bool, stating only that is must
be large enough to hold '0' and '1'.  Most, if not all, compilers use
a single byte for _Bool, including gcc[1].

Originally, 'launched' was of type 'int' and so the asm blob used 'cmpl'
to check the launch status.  When 'launched' was moved to be stored on a
per-VMCS basis, struct vcpu_vmx's "temporary" __launched flag was added
in order to avoid having to pass the current VMCS into the asm blob.
The new  '__launched' was defined as a 'bool' and not an 'int', but the
'cmp' instruction was not updated.

This has not caused any known problems, likely due to compilers aligning
variables to 4-byte or 8-byte boundaries and KVM zeroing out struct
vcpu_vmx during allocation.  I.e. vCPU-run accesses "junk" data, it just
happens to always be zero and so doesn't affect the result.

[1] https://gcc.gnu.org/ml/gcc-patches/2000-10/msg01127.html

Fixes: d462b819 ("KVM: VMX: Keep list of loaded VMCSs, instead of vcpus")
Cc: <stable@vger.kernel.org>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 58ac3230 ]

Stale && dirty keys can be produced in the follow way:
After writeback in write_dirty_finish(), dirty keys k1 will
replace by clean keys k2
==>ret = bch_btree_insert(dc->disk.c, &keys, NULL, &w->key);
==>btree_insert_fn(struct btree_op *b_op, struct btree *b)
==>static int bch_btree_insert_node(struct btree *b,
       struct btree_op *op,
       struct keylist *insert_keys,
       atomic_t *journal_ref,
Then two steps:
A) update k1 to k2 in btree node memory;
   bch_btree_insert_keys(b, op, insert_keys, replace_key)
B) Write the bset(contains k2) to cache disk by a 30s delay work
   bch_btree_leaf_dirty(b, journal_ref).
But before the 30s delay work write the bset to cache device,
these things happened:
A) GC works, and reclaim the bucket k2 point to;
B) Allocator works, and invalidate the bucket k2 point to,
   and increase the gen of the bucket, and place it into free_inc
   fifo;
C) Until now, the 30s delay work still does not finish work,
   so in the disk, the key still is k1, it is dirty and stale
   (its gen is smaller than the gen of the bucket). and then the
   machine power off suddenly happens;
D) When the machine power on again, after the btree reconstruction,
   the stale dirty key appear.

In bch_extent_bad(), when expensive_debug_checks is off, it would
treat the dirty key as good even it is stale keys, and it would
cause bellow probelms:
A) In read_dirty() it would cause machine crash:
   BUG_ON(ptr_stale(dc->disk.c, &w->key, 0));
B) It could be worse when reads hits stale dirty keys, it would
   read old incorrect data.

This patch tolerate the existence of these stale && dirty keys,
and treat them as bad key in bch_extent_bad().

(Coly Li: fix indent which was modified by sender's email client)
Signed-off-by: Tang Junhui <tang.junhui.linux@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 149d0efa ]

In extents.c:bch_extent_bad(), number 96 is used as parameter to call
btree_bug_on(). The purpose is to check whether stale gen value exceeds
BUCKET_GC_GEN_MAX, so it is better to use macro BUCKET_GC_GEN_MAX to
make the code more understandable.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8ab547a2 ]

* Rename TPM_BUFSIZE defined in drivers/char/tpm/st33zp24/st33zp24.h to
  ST33ZP24_BUFSIZE.
* Rename TPM_BUFSIZE defined in drivers/char/tpm/tpm_i2c_infineon.c to
  TPM_I2C_INFINEON_BUFSIZE.
* Rename TPM_RETRY in tpm_i2c_nuvoton to TPM_I2C_RETRIES.
* Remove TPM_HEADER_SIZE from tpm_i2c_nuvoton.

Cc: stable@vger.kernel.org
Fixes: bf38b871 ("tpm/tpm_i2c_stm_st33: Split tpm_i2c_tpm_st33 in 2 layers (core + phy)")
Fixes: aad628c1 ("char/tpm: Add new driver for Infineon I2C TIS TPM")
Fixes: 32d33b29 ("TPM: Retry SaveState command in suspend path")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 09fdc985 ]

INTEL_SOC_PMIC, INTEL_SOC_PMIC_CHTWC and MFD_TPS68470 select the
I2C_DESIGNWARE_PLATFORM without its dependencies making it possible to see
warning and build error like below:

WARNING: unmet direct dependencies detected for I2C_DESIGNWARE_PLATFORM
  Depends on [n]: I2C [=y] && HAS_IOMEM [=y] && (ACPI [=y] && COMMON_CLK [=n] || !ACPI [=y])
  Selected by [y]:
  - MFD_TPS68470 [=y] && HAS_IOMEM [=y] && ACPI [=y] && I2C [=y]=y

/usr/bin/ld: drivers/i2c/busses/i2c-designware-platdrv.o: in function `dw_i2c_plat_resume':
i2c-designware-platdrv.c:(.text+0x62): undefined reference to `i2c_dw_prepare_clk'
/usr/bin/ld: drivers/i2c/busses/i2c-designware-platdrv.o: in function `dw_i2c_plat_suspend':
i2c-designware-platdrv.c:(.text+0x9a): undefined reference to `i2c_dw_prepare_clk'
/usr/bin/ld: drivers/i2c/busses/i2c-designware-platdrv.o: in function `dw_i2c_plat_probe':
i2c-designware-platdrv.c:(.text+0x41c): undefined reference to `i2c_dw_prepare_clk'
/usr/bin/ld: i2c-designware-platdrv.c:(.text+0x438): undefined reference to `i2c_dw_read_comp_param'
/usr/bin/ld: i2c-designware-platdrv.c:(.text+0x545): undefined reference to `i2c_dw_probe'
/usr/bin/ld: i2c-designware-platdrv.c:(.text+0x727): undefined reference to `i2c_dw_probe_slave'

Fix this by making above options to depend on I2C_DESIGNWARE_PLATFORM
being built-in. I2C_DESIGNWARE_PLATFORM is a visible symbol with
dependencies so in general the select should be avoided.

Fixes: acebcff9 ("mfd: intel_soc_pmic: Select designware i2c-bus driver")
Fixes: de85d79f ("mfd: Add Cherry Trail Whiskey Cove PMIC driver")
Fixes: 9bbf6a15 ("mfd: Add support for TPS68470 device")
Cc: Stable <stable@vger.kernel.org> # v4.14+
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit cab870b7 ]

When there is no output no one will hold a runtime_pm reference
causing a warning when trying to read emom_status in debugfs.

[22.756480] ------------[ cut here ]------------
[22.756489] RPM wakelock ref not held during HW access
[22.756578] WARNING: CPU: 0 PID: 1058 at drivers/gpu/drm/i915/intel_drv.h:2104 gen5_read32+0x16b/0x1a0 [i915]
[22.756580] Modules linked in: snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic i915 coretemp crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core e1000e snd_pcm mei_me prime_numbers mei lpc_ich
[22.756595] CPU: 0 PID: 1058 Comm: debugfs_test Not tainted 4.20.0-rc1-CI-Trybot_3219+ #1
[22.756597] Hardware name: Hewlett-Packard HP Compaq 8100 Elite SFF PC/304Ah, BIOS 786H1 v01.13 07/14/2011
[22.756634] RIP: 0010:gen5_read32+0x16b/0x1a0 [i915]
[22.756637] Code: a4 ea e0 0f 0b e9 d2 fe ff ff 80 3d a5 71 19 00 00 0f 85 d3 fe ff ff 48 c7 c7 48 d0 2d a0 c6 05 91 71 19 00 01 e8 35 a4 ea e0 <0f> 0b e9 b9 fe ff ff e8 69 c6 f2 e0 85 c0 75 92 48 c7 c2 78 d0 2d
[22.756639] RSP: 0018:ffffc90000f1fd38 EFLAGS: 00010282
[22.756642] RAX: 0000000000000000 RBX: ffff8801f7ab0000 RCX: 0000000000000006
[22.756643] RDX: 0000000000000006 RSI: ffffffff8212886a RDI: ffffffff820d6d57
[22.756645] RBP: 0000000000011020 R08: 0000000043e3d1a8 R09: 0000000000000000
[22.756647] R10: ffffc90000f1fd80 R11: 0000000000000000 R12: 0000000000000001
[22.756649] R13: ffff8801f7ab0068 R14: 0000000000000001 R15: ffff88020d53d188
[22.756651] FS:  00007f2878849980(0000) GS:ffff880213a00000(0000) knlGS:0000000000000000
[22.756653] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[22.756655] CR2: 00005638deedf028 CR3: 0000000203292001 CR4: 00000000000206f0
[22.756657] Call Trace:
[22.756689]  i915_mch_val+0x1b/0x60 [i915]
[22.756721]  i915_emon_status+0x45/0xd0 [i915]
[22.756730]  seq_read+0xdb/0x3c0
[22.756736]  ? lockdep_hardirqs_off+0x94/0xd0
[22.756740]  ? __slab_free+0x24e/0x510
[22.756746]  full_proxy_read+0x52/0x90
[22.756752]  __vfs_read+0x31/0x170
[22.756759]  ? do_sys_open+0x13b/0x240
[22.756763]  ? rcu_read_lock_sched_held+0x6f/0x80
[22.756766]  vfs_read+0x9e/0x140
[22.756770]  ksys_read+0x50/0xc0
[22.756775]  do_syscall_64+0x55/0x190
[22.756781]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[22.756783] RIP: 0033:0x7f28781dc34e
[22.756786] Code: 00 00 00 00 48 8b 15 71 8c 20 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff c3 0f 1f 40 00 8b 05 ba d0 20 00 85 c0 75 16 31 c0 0f 05 <48> 3d 00 f0 ff ff 77 5a f3 c3 0f 1f 84 00 00 00 00 00 41 54 55 49
[22.756787] RSP: 002b:00007ffd33fa0d08 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
[22.756790] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f28781dc34e
[22.756792] RDX: 0000000000000200 RSI: 00007ffd33fa0d50 RDI: 0000000000000008
[22.756794] RBP: 00007ffd33fa0f60 R08: 0000000000000000 R09: 0000000000000020
[22.756796] R10: 0000000000000000 R11: 0000000000000246 R12: 00005638de45c2c0
[22.756797] R13: 00007ffd33fa14b0 R14: 0000000000000000 R15: 0000000000000000
[22.756806] irq event stamp: 47950
[22.756811] hardirqs last  enabled at (47949): [<ffffffff810fba74>] vprintk_emit+0x124/0x320
[22.756813] hardirqs last disabled at (47950): [<ffffffff810019b0>] trace_hardirqs_off_thunk+0x1a/0x1c
[22.756816] softirqs last  enabled at (47518): [<ffffffff81c0033a>] __do_softirq+0x33a/0x4b9
[22.756820] softirqs last disabled at (47479): [<ffffffff8108df29>] irq_exit+0xa9/0xc0
[22.756858] WARNING: CPU: 0 PID: 1058 at drivers/gpu/drm/i915/intel_drv.h:2104 gen5_read32+0x16b/0x1a0 [i915]
[22.756860] ---[ end trace bf56fa7d6a3cbf7a ]
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181119230101.32460-1-jose.souza@intel.comSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ed20151a ]

On i965gm we need to adjust max_vblank_count dynamically
depending on whether the TV encoder is used or not. To
that end add a per-crtc max_vblank_count that takes
precedence over its device wide counterpart. The driver
can now call drm_crtc_set_max_vblank_count() to configure
the per-crtc value before calling drm_vblank_on().

Also looks like there was some discussion about exynos needing
similar treatment.

v2: Drop the extra max_vblank_count!=0 check for the
    WARN(last!=current), will take care of it in i915 code (Daniel)
    WARN_ON(!inmodeset) (Daniel)
    WARN_ON(dev->max_vblank_count)
    Pimp up the docs (Daniel)

Cc: stable@vger.kernel.org
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127182004.28885-1-ville.syrjala@linux.intel.comReviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f1071c3e ]

Commit 1358c13a ("crypto: ccree - fix resume race condition on init")
was missing a "inline" qualifier for stub function used when CONFIG_PM
is not set causing a build warning.

Fixes: 1358c13a ("crypto: ccree - fix resume race condition on init")
Cc: stable@kernel.org # v4.20
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1358c13a ]

We were enabling autosuspend, which is using data set by the
hash module, prior to the hash module being inited, casuing
a crash on resume as part of the startup sequence if the race
was lost.

This was never a real problem because the PM infra was using low
res timers so we were always winning the race, until commit 8234f673
("PM-runtime: Switch autosuspend over to using hrtimers") changed that :-)

Fix this by seperating the PM setup and enablement and doing the
latter only at the end of the init sequence.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: stable@kernel.org # v4.20
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 425784aa ]

The async_file might be freed before the disassociation has been ended,
causing qp shutdown to use after free on it.

Since uverbs_destroy_ufile_hw is not a fence, it returns if a
disassociation is ongoing in another thread. It has to be written this way
to avoid deadlock. However this means that the ufile FD close cannot
destroy anything that may still be used by an active kref, such as the the
async_file.

To fix that move the kref_put() to be in ib_uverbs_release_file().

 BUG: unable to handle kernel paging request at ffffffffba682787
 PGD bc80e067 P4D bc80e067 PUD bc80f063 PMD 1313df163 PTE 80000000bc682061
 Oops: 0003 [#1] SMP PTI
 CPU: 1 PID: 32410 Comm: bash Tainted: G           OE 4.20.0-rc6+ #3
 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
 RIP: 0010:__pv_queued_spin_lock_slowpath+0x1b3/0x2a0
 Code: 98 83 e2 60 49 89 df 48 8b 04 c5 80 18 72 ba 48 8d
		ba 80 32 02 00 ba 00 80 00 00 4c 8d 65 14 41 bd 01 00 00 00 48 01 c7 85
		d2 <48> 89 2f 48 89 fb 74 14 8b 45 08 85 c0 75 42 84 d2 74 6b f3 90 83
 RSP: 0018:ffffc1bbc064fb58 EFLAGS: 00010006
 RAX: ffffffffba65f4e7 RBX: ffff9f209c656c00 RCX: 0000000000000001
 RDX: 0000000000008000 RSI: 0000000000000000 RDI: ffffffffba682787
 RBP: ffff9f217bb23280 R08: 0000000000000001 R09: 0000000000000000
 R10: ffff9f209d2c7800 R11: ffffffffffffffe8 R12: ffff9f217bb23294
 R13: 0000000000000001 R14: 0000000000000000 R15: ffff9f209c656c00
 FS:  00007fac55aad740(0000) GS:ffff9f217bb00000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: ffffffffba682787 CR3: 000000012f8e0000 CR4: 00000000000006e0
 Call Trace:
  _raw_spin_lock_irq+0x27/0x30
  ib_uverbs_release_uevent+0x1e/0xa0 [ib_uverbs]
  uverbs_free_qp+0x7e/0x90 [ib_uverbs]
  destroy_hw_idr_uobject+0x1c/0x50 [ib_uverbs]
  uverbs_destroy_uobject+0x2e/0x180 [ib_uverbs]
  __uverbs_cleanup_ufile+0x73/0x90 [ib_uverbs]
  uverbs_destroy_ufile_hw+0x5d/0x120 [ib_uverbs]
  ib_uverbs_remove_one+0xea/0x240 [ib_uverbs]
  ib_unregister_device+0xfb/0x200 [ib_core]
  mlx5_ib_remove+0x51/0xe0 [mlx5_ib]
  mlx5_remove_device+0xc1/0xd0 [mlx5_core]
  mlx5_unregister_device+0x3d/0xb0 [mlx5_core]
  remove_one+0x2a/0x90 [mlx5_core]
  pci_device_remove+0x3b/0xc0
  device_release_driver_internal+0x16d/0x240
  unbind_store+0xb2/0x100
  kernfs_fop_write+0x102/0x180
  __vfs_write+0x36/0x1a0
  ? __alloc_fd+0xa9/0x170
  ? set_close_on_exec+0x49/0x70
  vfs_write+0xad/0x1a0
  ksys_write+0x52/0xc0
  do_syscall_64+0x5b/0x180
  entry_SYSCALL_64_after_hwframe+0x44/0xa9
 RIP: 0033:0x7fac551aac60

Cc: <stable@vger.kernel.org> # 4.2
Fixes: 036b1063 ("IB/uverbs: Enable device removal when there are active user space applications")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4d447455 ]

do_page_fault() forgot to relinquish mmap_sem if a signal came while
handling handle_mm_fault() - due to say a ctl+c or oom etc.
This would later cause a deadlock by acquiring it twice.

This came to light when running libc testsuite tst-tls3-malloc test but
is likely also the cause for prior seen LTP failures. Using lockdep
clearly showed what the issue was.

| # while true; do ./tst-tls3-malloc ; done
| Didn't expect signal from child: got `Segmentation fault'
| ^C
| ============================================
| WARNING: possible recursive locking detected
| 4.17.0+ #25 Not tainted
| --------------------------------------------
| tst-tls3-malloc/510 is trying to acquire lock:
| 606c7728 (&mm->mmap_sem){++++}, at: __might_fault+0x28/0x5c
|
|but task is already holding lock:
|606c7728 (&mm->mmap_sem){++++}, at: do_page_fault+0x9c/0x2a0
|
| other info that might help us debug this:
|  Possible unsafe locking scenario:
|
|       CPU0
|       ----
|  lock(&mm->mmap_sem);
|  lock(&mm->mmap_sem);
|
| *** DEADLOCK ***
|

------------------------------------------------------------
What the change does is not obvious (note to myself)

prior code was

| do_page_fault
|
|   down_read()		<-- lock taken
|   handle_mm_fault	<-- signal pending as this runs
|   if fatal_signal_pending
|       if VM_FAULT_ERROR
|           up_read
|       if user_mode
|          return	<-- lock still held, this was the BUG

New code

| do_page_fault
|
|   down_read()		<-- lock taken
|   handle_mm_fault	<-- signal pending as this runs
|   if fatal_signal_pending
|       if VM_FAULT_RETRY
|          return       <-- not same case as above, but still OK since
|                           core mm already relinq lock for FAULT_RETRY
|    ...
|
|   < Now falls through for bug case above >
|
|   up_read()		<-- lock relinquished

Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f731a8e8 ]

signal handling core calls show_regs() with preemption disabled which
on ARC takes mmap_sem for mm/vma access, causing lockdep splat.

| [ARCLinux]# ./segv-null-ptr
| potentially unexpected fatal signal 11.
| BUG: sleeping function called from invalid context at kernel/fork.c:1011
| in_atomic(): 1, irqs_disabled(): 0, pid: 70, name: segv-null-ptr
| no locks held by segv-null-ptr/70.
| CPU: 0 PID: 70 Comm: segv-null-ptr Not tainted 4.18.0+ #69
|
| Stack Trace:
|  arc_unwind_core+0xcc/0x100
|  ___might_sleep+0x17a/0x190
|  mmput+0x16/0xb8
|  show_regs+0x52/0x310
|  get_signal+0x5ee/0x610
|  do_signal+0x2c/0x218
|  resume_user_mode_begin+0x90/0xd8

Workaround by re-enabling preemption temporarily.

Note that the preemption disabling in core code around show_regs()
was introduced by commit 3a9f84d3 ("signals, debug: fix BUG: using
smp_processor_id() in preemptible code in print_fatal_signal()")

to silence a differnt lockdep seen on x86 bakc in 2009.

Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 240809ef ]

cancel_delayed_work_sync() was called for any queue, but it should only
be called for the queue that is associated with the currently running job.

Otherwise, if two filehandles are streaming at the same time, then closing the
first will cancel the work which might still be running for a job from the
second filehandle. As a result the second filehandle will never be able to
finish the job and an attempt to stop streaming on that second filehandle will
stall.

Fixes: 52117be6 ("media: vim2m: use cancel_delayed_work_sync instead of flush_schedule_work")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org>      # for v4.20 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1b3922a8 ]

[BUG]
Linux v5.0-rc1 will fail fstests/btrfs/163 with the following kernel
message:

  BTRFS error (device dm-6): dev extent devid 1 physical offset 13631488 len 8388608 is beyond device boundary 0
  BTRFS error (device dm-6): failed to verify dev extents against chunks: -117
  BTRFS error (device dm-6): open_ctree failed

[CAUSE]
Commit cf90d884 ("btrfs: Introduce mount time chunk <-> dev extent
mapping check") introduced strict check on dev extents.

We use btrfs_find_device() with dev uuid and fs uuid set to NULL, and
only dependent on @devid to find the real device.

For seed devices, we call clone_fs_devices() in open_seed_devices() to
allow us search seed devices directly.

However clone_fs_devices() just populates devices with devid and dev
uuid, without populating other essential members, like disk_total_bytes.

This makes any device returned by btrfs_find_device(fs_info, devid,
NULL, NULL) is just a dummy, with 0 disk_total_bytes, and any dev
extents on the seed device will not pass the device boundary check.

[FIX]
This patch will try to verify the device returned by btrfs_find_device()
and if it's a dummy then re-search in seed devices.

Fixes: cf90d884 ("btrfs: Introduce mount time chunk <-> dev extent mapping check")
CC: stable@vger.kernel.org # 4.19+
Reported-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 05a37c48 ]

Add extra dev extent end check against device boundary.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2cd4bd19 ]

Protection key tracking information is not copied over to the
mm_struct of the child during fork(). This can cause the child to
erroneously allocate keys that were already allocated. Any allocated
execute-only key is lost aswell.

Add code; called by dup_mmap(), to copy the pkey state from parent to
child explicitly.

This problem was originally found by Dave Hansen on x86, which turns
out to be a problem on powerpc aswell.

Fixes: cf43d3b2 ("powerpc: Enable pkey subsystem")
Cc: stable@vger.kernel.org # v4.16+
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 894169db ]

Although MegaRAID controllers support 64-bit DMA addressing, as per
hardware design, DMA address with all 64-bits set
(0xFFFFFFFF-FFFFFFFF) results in a firmware fault.

Driver will set 63-bit DMA mask to ensure the above address will not be
used.

Cc: stable@vger.kernel.org
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit de93b40d ]

For SAS3 and later controllers, FW sets the reset adapter bit indicating
the driver to perform a controller reset.  Driver needs to check if this
bit is set before doing a reset.  This reduces the driver probe failure
time to 180seconds in case there is a faulty controller connected.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e29c3221 ]

For Invader series, if FW supports more than 8 MSI-x vectors, driver needs
to enable combined reply queue mode. For Ventura series, driver enables
combined reply queue mode in case of more than 16 MSI-x vectors.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d1051d6e ]

Running btrfs/124 in a loop hung up on me sporadically with the
following call trace:

	btrfs           D    0  5760   5324 0x00000000
	Call Trace:
	 ? __schedule+0x243/0x800
	 schedule+0x33/0x90
	 btrfs_start_ordered_extent+0x10c/0x1b0 [btrfs]
	 ? wait_woken+0xa0/0xa0
	 btrfs_wait_ordered_range+0xbb/0x100 [btrfs]
	 btrfs_relocate_block_group+0x1ff/0x230 [btrfs]
	 btrfs_relocate_chunk+0x49/0x100 [btrfs]
	 btrfs_balance+0xbeb/0x1740 [btrfs]
	 btrfs_ioctl_balance+0x2ee/0x380 [btrfs]
	 btrfs_ioctl+0x1691/0x3110 [btrfs]
	 ? lockdep_hardirqs_on+0xed/0x180
	 ? __handle_mm_fault+0x8e7/0xfb0
	 ? _raw_spin_unlock+0x24/0x30
	 ? __handle_mm_fault+0x8e7/0xfb0
	 ? do_vfs_ioctl+0xa5/0x6e0
	 ? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs]
	 do_vfs_ioctl+0xa5/0x6e0
	 ? entry_SYSCALL_64_after_hwframe+0x3e/0xbe
	 ksys_ioctl+0x3a/0x70
	 __x64_sys_ioctl+0x16/0x20
	 do_syscall_64+0x60/0x1b0
	 entry_SYSCALL_64_after_hwframe+0x49/0xbe

This happens because during page writeback it's valid for
writepage_delalloc to instantiate a delalloc range which doesn't belong
to the page currently being written back.

The reason this case is valid is due to find_lock_delalloc_range
returning any available range after the passed delalloc_start and
ignoring whether the page under writeback is within that range.

In turn ordered extents (OE) are always created for the returned range
from find_lock_delalloc_range. If, however, a failure occurs while OE
are being created then the clean up code in btrfs_cleanup_ordered_extents
will be called.

Unfortunately the code in btrfs_cleanup_ordered_extents doesn't consider
the case of such 'foreign' range being processed and instead it always
assumes that the range OE are created for belongs to the page. This
leads to the first page of such foregin range to not be cleaned up since
it's deliberately missed and skipped by the current cleaning up code.

Fix this by correctly checking whether the current page belongs to the
range being instantiated and if so adjsut the range parameters passed
for cleaning up. If it doesn't, then just clean the whole OE range
directly.

Fixes: 52427260 ("btrfs: Handle delalloc error correctly to avoid ordered extent hang")
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5eaad97a ]

This callback is called only from writepage_delalloc which in turn is
guaranteed to be called from the data page writeout path. In the end
there is no reason to have the call to this function to be indrected via
the extent_io_ops structure. This patch removes the callback definition,
exports the function and calls it directly. No functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ rename to btrfs_run_delalloc_range ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a5fb1142 ]

When a transaction commit starts, it attempts to pause scrub and it blocks
until the scrub is paused. So while the transaction is blocked waiting for
scrub to pause, we can not do memory allocation with GFP_KERNEL from scrub,
otherwise we risk getting into a deadlock with reclaim.

Checking for scrub pause requests is done early at the beginning of the
while loop of scrub_stripe() and later in the loop, scrub_extent() and
scrub_raid56_parity() are called, which in turn call scrub_pages() and
scrub_pages_for_parity() respectively. These last two functions do memory
allocations using GFP_KERNEL. Same problem could happen while scrubbing
the super blocks, since it calls scrub_pages().

We also can not have any of the worker tasks, created by the scrub task,
doing GFP_KERNEL allocations, because before pausing, the scrub task waits
for all the worker tasks to complete (also done at scrub_stripe()).

So make sure GFP_NOFS is used for the memory allocations because at any
time a scrub pause request can happen from another task that started to
commit a transaction.

Fixes: 58c4e173 ("btrfs: scrub: use GFP_KERNEL on the submission path")
CC: stable@vger.kernel.org # 4.6+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 32934280 ]

struct scrub_ctx has an ->is_dev_replace member, so there's no point in
passing around is_dev_replace where sctx is available.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 234ff0b7 ]

Testing has revealed an occasional crash which appears to be caused
by a race between kvmppc_switch_mmu_to_hpt and kvm_unmap_hva_range_hv.
The symptom is a NULL pointer dereference in __find_linux_pte() called
from kvm_unmap_radix() with kvm->arch.pgtable == NULL.

Looking at kvmppc_switch_mmu_to_hpt(), it does indeed clear
kvm->arch.pgtable (via kvmppc_free_radix()) before setting
kvm->arch.radix to NULL, and there is nothing to prevent
kvm_unmap_hva_range_hv() or the other MMU callback functions from
being called concurrently with kvmppc_switch_mmu_to_hpt() or
kvmppc_switch_mmu_to_radix().

This patch therefore adds calls to spin_lock/unlock on the kvm->mmu_lock
around the assignments to kvm->arch.radix, and makes sure that the
partition-scoped radix tree or HPT is only freed after changing
kvm->arch.radix.

This also takes the kvm->mmu_lock in kvmppc_rmap_reset() to make sure
that the clearing of each rmap array (one per memslot) doesn't happen
concurrently with use of the array in the kvm_unmap_hva_range_hv()
or the other MMU callbacks.

Fixes: 18c3640c ("KVM: PPC: Book3S HV: Add infrastructure for running HPT guests on radix host")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 30b71084 ]

Since the gt powerstate is allocated by i915_gem_init, clean it from
i915_gem_fini for symmetry and to correct the imbalance on error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180812223642.24865-1-chris@chris-wilson.co.ukSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7ed43df7 ]

If we fail during GEM initialisation, we scrub the HW state by
performing a device level GPU resuet. However, we want to leave the
system in a usable state (with functioning KMS but no GEM) so after
scrubbing the HW state, we need to restore some sane defaults and
re-enable the low-level common parts of the GPU (such as the GMCH).

v2: Restore GTT entries.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180726085033.4044-2-chris@chris-wilson.co.ukReviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 52117be6 ]

The use of flush_schedule_work() made no sense and caused a syzkaller error.
Replace with the correct cancel_delayed_work_sync().
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+69780d144754b8071f4b@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>      # for v4.20 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 144bd0ee ]

v4l2_ctrl uses mutexes, so we can't setup a ctrl_handler in
interrupt context. Switch to a workqueue instead and drop the timer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 104f708f ]

Until the vfio-ap driver came into live there was a well known
agreement about the way how ap devices are initialized and their
states when the driver's probe function is called.

However, the vfio device driver when receiving an ap queue device does
additional resets thereby removing the registration for interrupts for
the ap device done by the ap bus core code. So when later the vfio
driver releases the device and one of the default zcrypt drivers takes
care of the device the interrupt registration needs to get
renewed. The current code does no renew and result is that requests
send into such a queue will never see a reply processed - the
application hangs.

This patch adds a function which resets the aq queue state machine for
the ap queue device and triggers the walk through the initial states
(which are reset and registration for interrupts). This function is
now called before the driver's probe function is invoked.

When the association between driver and device is released, the
driver's remove function is called. The current implementation calls a
ap queue function ap_queue_remove(). This invokation has been moved to
the ap bus function to make the probe / remove pair for ap bus and
drivers more symmetric.

Fixes: 7e0bdbe5 ("s390/zcrypt: AP bus support for alternate driver(s)")
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewd-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewd-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit adcf60ce ]

Since commit eb3744a2 ("gpio: davinci: Do not assume continuous
IRQ numbering") the davinci GPIO driver fails to probe if we boot
in legacy mode from any of the board files. Since the driver now
expects every interrupt to be defined as a separate resource, split
the definition of IRQ resources instead of having a single continuous
interrupt range.

Fixes: eb3744a2 ("gpio: davinci: Do not assume continuous IRQ numbering")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 27db7baa ]

Since commit eb3744a2 ("gpio: davinci: Do not assume continuous
IRQ numbering") the davinci GPIO driver fails to probe if we boot
in legacy mode from any of the board files. Since the driver now
expects every interrupt to be defined as a separate resource, split
the definition of IRQ resources instead of having a single continuous
interrupt range.

Fixes: eb3744a2 ("gpio: davinci: Do not assume continuous IRQ numbering")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>