There are a number of other ioctls that aren't used anywhere
inside the Kernel tree.

Get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

While this ioctl is there at least since Kernel 2.6.12-rc2, it
was never used by any upstream driver.

Get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The em28xx driver never touched the EM2874 register bits that control
the transport stream packet filters, leaving them at whatever default
the firmware has set. E.g. the Pinnacle 290e disables them by default,
while the Hauppauge WinTV dualHD enables discarding NULL packets by
default.

However, some applications require NULL packets, e.g. to determine the
load in DOCSIS segments, so discarding NULL packets is undesired for
such applications.

This patch simply extends the bit mask when starting or stopping the
transport stream packet capture, so that the filter bits are cleared.
It has been verified that this makes the Hauppauge WinTV dualHD pass
an unfiltered DVB-C stream including NULL packets, which it didn't
before.
Signed-off-by: Robert Schlabbach <Robert.Schlabbach@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

add entries for the following drivers:
- earth_pt{1,3} DVB adapter drivers
- mxl301rf DVB tuner drivers
- qm1d1{b0004, c0042} DVB tuner drivers
- tc90522 DVB demod driver
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Found and reported by kbuild test robot:
Message ID: <201805052003.MC007f9h%fengguang.wu@intel.com>
and holding an address of an empty struct in .driver.pm does no harm
when CONFIG_PM_SLEEP is not defined.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

dvb-pll module was 'put' twice on exit:
once by dvb_frontend_detach() and another by dvb_module_release().
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Friio device contains "gl861" bridge and "tc90522" demod,
for which the separate drivers are already in the kernel.
But friio driver was monolithic and did not use them,
practically copying those features.
This patch decomposes friio driver into sub drivers and
re-uses existing ones, thus reduces some code.

It adds some features to gl861,
to support the friio-specific init/config of the devices
and implement i2c communications to the tuner via demod
with USB vendor requests.

[mchehab+samsung@kernel.org: fix merge conflicts]
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The include/linux/platform_data/media/sii9234.h header file is unused,
let's remove it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Look up of buffers in s5p_mfc_handle_frame_new, s5p_mfc_handle_frame_copy_time
functions is not working properly for DMA addresses above 2 GiB. As a result
flags and timestamp of returned buffers are not set correctly and it breaks
operation of GStreamer/OMX plugins which rely on the CAPTURE buffer queue
flags.

Due to improper return type of the get_dec_y_adr, get_dspl_y_adr callbacks
and sign bit extension these callbacks return incorrect address values,
e.g. 0xfffffffffefc0000 instead of 0x00000000fefc0000. Then the statement:

"if (vb2_dma_contig_plane_dma_addr(&dst_buf->b->vb2_buf, 0) == dec_y_addr)"

is always false, which breaks looking up capture queue buffers.

To ensure proper matching by address u32 type is used for the DMA
addresses. This should work on all related SoCs, since the MFC DMA
address width is not larger than 32-bit.

Changes done in this patch are minimal as there is a larger patch series
pending refactoring the whole driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Commit 34dbb848 ("media: mem2mem: Remove excessive try_run call")
removed a redundant call to v4l2_m2m_try_run but instead introduced
a bug. Consider the following case:

 1) Context A schedules, queues and runs job A.
 2) While the m2m device is running, context B schedules
    and queues job B. Job B cannot run, because it has to
    wait for job A.
 3) Job A completes, calls v4l2_m2m_job_finish, and tries
    to queue a job for context A, but since the context is
    empty it won't do anything.

In this scenario, queued job B will never run. Fix this by calling
v4l2_m2m_try_run from v4l2_m2m_try_schedule.

While here, add more documentation to these functions.

Fixes: 34dbb848 ("media: mem2mem: Remove excessive try_run call")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: split >80 cols line]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Currently this driver does not support cropping. The supported modes
are the following, all capturing the entire area:

 - 3840x2160, 1:1 binning (native sensor resolution)
 - 1920x1080, 2:1 binning
 - 1280x720,  3:1 binning

The VIDIOC_SUBDEV_S_FMT ioctl chooses among these 3 configurations the
one that matches the requested format.

Add cropping support via VIDIOC_SUBDEV_S_SELECTION: with target
V4L2_SEL_TGT_CROP to choose the captured area, with
V4L2_SEL_TGT_COMPOSE to choose the output resolution.

To maintain backward compatibility we also allow setting the compose
format via VIDIOC_SUBDEV_S_FMT. To obtain this, compose rect and
output format are computed in the common helper function
__imx274_change_compose(), which sets both to the same width/height
values.

Cropping also calls __imx274_change_compose() whenever cropping rect
size changes in order to reset the compose rect (and output format
size) for 1:1 binning.

Also rename enum imx274_mode to imx274_binning (and its values from
IMX274_MODE_BINNING_* to IMX274_BINNING_*). Without cropping, the two
naming are equivalent. With cropping, the resolution could be
different, e.g. using 2:1 binning mode to crop 1200x960 and output a
600x480 format. Using binning in the names avoids any
misunderstanding. For the same reason, replace the 'size' field in
struct imx274_frmfmt with 'bin_ratio'.

[Sakari Ailus: Remove leftover condition in imx274_apply_trimming]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Currently 2-bytes and 3-bytes registers are set by very similar
functions doing the needed shift & mask manipulation, followed by very
similar for loops setting one byte at a time over I2C.

Replace all of this code by a unique helper function that calls
regmap_bulk_write(), which has two advantages:
 - sets all the bytes in a unique I2C transaction
 - removes lots of now unused code.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

This patch adds V4L2 sub-device driver for OV2680 image sensor.
The OV2680 is a 1/5" CMOS color sensor from Omnivision.
Supports output format: 10-bit Raw RGB.
The OV2680 has a single lane MIPI interface.

The driver exposes following V4L2 controls:
- auto/manual exposure,
- exposure,
- auto/manual gain,
- gain,
- horizontal/vertical flip,
- test pattern menu.
Supported resolution are only: QUXGA, 720P, UXGA.

[Sakari Ailus: Drop "-level" from Kconfig help text]
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Add device tree binding documentation for the OV2680 camera sensor.

[Sakari Ailus: Squash MAINTAINERS entry from Rui]

CC: devicetree@vger.kernel.org
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Add V4L2 sensor driver for Aptina MT9V111 CMOS image sensor.

The MT9V111 is a 1/4-Inch CMOS image sensor based on MT9V011 with an
integrated Image Flow Processor.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Add documentation for Aptina MT9V111 image sensor.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The dw9807 contains a voice coil lens driver as well as an EEPROM. This
driver is just for the VCM. Reflect this in the driver's name --- this is
already the case for the compatible string, for instance.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Latest errata document updates the start procedure for V3M. This change
in addition to adhering to the datasheet update fixes capture on early
revisions of V3M.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

ivtv_probe() and ivtvfb_init_card() are never called in atomic context.
They call kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.

This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

dvb_register() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().

This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

cx88_card_setup_pre_i2c() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().

This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

cx25821_gpio_init(), cx25821_initialize() and cx25821_registers_init()
are never called in atomic context.
They call mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().

This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

cx23885_reset() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().

This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

cx23885_gpio_setup() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep() and usleep_range().

This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

altera_ci_slot_reset() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().

This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

cobalt_probe() is never called in atomic context.
It calls kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.

This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

vs6624_probe() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep() and usleep_range().

This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

adv7842_ddr_ram_test() is never called in atomic context.
It only calls from:
adv7842_ddr_ram_test() <- adv7842_command_ram_test() <- adv7842_ioctl()

adv7842_ddr_ram_test() calls mdelay() to busily wait,
which is not necessary.
mdelay() can be replaced with msleep() and usleep_range().

This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

PTR_ERR was making any pointer passed an error pointer, and should be
replaced with PTR_ERR_OR_ZERO which checks if is an actual error condition.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Implement g_frame_interval to return the current standard's frame
interval.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The ADV7180 and ADV7182 transmit whole fields, bottom field followed
by top (or vice-versa, depending on detected video standard). So
for chips that do not have support for explicitly setting the field
mode via I2P, set the field mode to V4L2_FIELD_ALTERNATE.

I2P converts fields into frames using an edge adaptive algorithm. The
frame rate is the same as the 'field rate': e.g. X fields per second
are now X frames per second.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

In rga_remove(), dma_free_attrs is being passed the wrong
cpu address, which triggers an exception if the driver is
removed. Fix it.

Tested on a RK3399 platform, with a bind/unbind cycle.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The media.h public header is one of only three public headers that include
linux/version.h. Drop it from media.h. It was only used for an obsolete
define.

It has to be added to media-device.c, since that source relied on media.h
to include it.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The vivid driver will overlay stream time on generated frames. Though,
in interlacing mode V4L2_FIELD_ALTERNATE, each field is separate and
must have the same time to ensure proper render. Though, this time was
only updated every 2 frames as the code was checking against the wrong
counter (frame counter rather then field counter).
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

This was kept just for backward compatibility. Solves this warning:
	media.h.rst:6: WARNING: undefined label: media-ent-f-dtv-decoder (if the link has no caption the label must precede a section header)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

The CODA7541 firmware does not set the SPS frame cropping fields to
properly describe coded h.264 streams with frame sizes that are not a
multiple of the macroblock size.
This adds RBSP parsing code and a SPS fixup routine to manually replace
the cropping information in the headers produced by the firmware with
the correct values.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[hans.verkuil@cisco.com: added explanation of SPS RBSP to comment]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

When encoding h.264, if visible resolution is not aligned to macroblock
size, frame cropping has to be set in the SPS header to produce correct
streams. The CODA960 firmware can do this on its own if asked to.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Fix these warnings when building the documentation:

media.h.rst:6: WARNING: undefined label: media-ent-f-dv-decoder (if the link has no caption the label must precede a section header)
media.h.rst:6: WARNING: undefined label: media-ent-f-dv-encoder (if the link has no caption the label must precede a section header)
media.h.rst:6: WARNING: undefined label: media-ent-f-dv-decoder (if the link has no caption the label must precede a section header)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

This patch fixes crystal frequency setting when power on this device.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

In commit 2d9445db ("media: vsp1: Use reference counting for
bodies"), a new field was introduced to the vsp1_dl_body structure to
account for usage tracking of the body.

Document the newly added field in the kerneldoc.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>