Add function to allow the configuation fo the VDCDC2 register by
external users, to allow changing of the standard and low-power
running modes.

This is needed, for example, for the Simtec IM2440D20 where we need
to use the low-power mode to shutdown the LDO/DCDC that are not needed
during suspend (saving substantial power) and the runtime use of the
low-power mode to change VCore.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If the board does not care where the TPS turns up, then specifiying the
value -1 to get gpiolib to dynamically allocate the base for the chip
is valid.

Change the test to look for != 0, so that any boards specifying zero
will not end up with gpio that they didn't want.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Liunx Team <linux@simtec.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Allows TWL's 32kHz oscillator to go in low-power mode when
main battery voltage is running low.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This is currently unused by the wm8350 drivers but getting it merged
now will reduce merge issues in the future when implementing wm8350
genirq support.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Based on Aaro's previous fix, this needs to be fixed for the newly added
remap_off and remap_sleep resources as well.

The code tries to skip values initialized with -1, but since the values
are unsigned the comparison is always true.

The patch eliminates the following compiler warnings:

drivers/mfd/twl4030-power.c: In function 'twl4030_configure_resource':
drivers/mfd/twl4030-power.c:338: warning: comparison is always true due to
limited range of data type
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The power scripts optimisation was mainly done by:
Tero Kristo <tero.kristo@nokia.com> and
Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>

I'm only refactoring and testing it against the mainline kernel.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: linux-omap@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Currently the child devices were not freed if the irq could not be requested.
This patch restructures the function, that in case of an error all previously
allocated resources are freed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The function is not exported as the __ indicates. __
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The code tries to skip values initialized with -1, but since the values
are unsigned the comparison is always true.

The patch eliminates the following compiler warnings:

drivers/mfd/twl4030-power.c: In function 'twl4030_configure_resource':
drivers/mfd/twl4030-power.c:338: warning: comparison is always true due to
limited range of data type
drivers/mfd/twl4030-power.c:358: warning: comparison is always true due to
limited range of data type
drivers/mfd/twl4030-power.c:363: warning: comparison is always true due to
limited range of data type
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The <RESOURCE>_REMAP register allows configuration of the <RESOURCE> in case
of a sleep or off transition.

Allow this property of resources to be configured (through twl4030_resconfig)
and add code to parse these values to program the registers accordingly.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Describe how the resource registers are laid out and the various bit-fields in
them.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Stick to the names used in the reference manual
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Currently the pcf50633-regulator driver data is set to the pcf50633 core
structure, but the pcf50633-regulator remove handler assumes that it is set to
the regulator device. This patch fixes the issue by accessing the pcf506533
core structure through its parent device and setting the driver data to the
regulator device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Platform devices allocated with platform_device_alloc should use
platform_device_add_data to set the platform data, because kfree will be called
on the platform_data when the device is released.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Since platform_device_add_data copies the passed data, the allocated
subdev_pdata is never freed. A simple fix would be to either free subdev_pdata
or put it onto the stack. But since the pcf50633 child devices can rely on
beeing children of the pcf50633 core device it's much more elegant to get access
to pcf50633 core structure through that link. This allows to get completly rid
of pcf5033_subdev_pdata.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

IRQs masking/unmasking should be less verbose.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When not using the i2c suspend/resume callbacks the i2c client resumed
before the i2c master.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

On gta02 hardware revision A5 it can actually bring the system down
during normal operating conditions so we disable it.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Rather than open coding individual IRQs in each function which
manipulates them store data for IRQs in a table which is then
referenced in the users.

This is a substantial code shrink and should be a performance win in
cases where only a single IRQ goes off at once since instead of
reading four of the second level IRQ registers for each interrupt
we read only the sub-registers which have had an interrupt flagged.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

In preparation for refactoring - it's over 700 lines of well-isolated
code and having it in a file by itself makes things more managable.

While we're at it make sure that we clean up the IRQ if we fail after
acquiring it on init.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Base driver for Analog Devices ADP5520/ADP5501 MFD PMICs

Subdevs:
LCD Backlight   : drivers/video/backlight/adp5520_bl.c
LEDs            : drivers/led/leds-adp5520.c
GPIO            : drivers/gpio/adp5520-gpio.c (ADP5520 only)
Keys            : drivers/input/keyboard/adp5520-keys.c (ADP5520 only)
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The common adp5520 mfd defines were namespaced to avoid collisions, so
update the define used in this driver accordingly.  The structs were also
renamed to fix a spelling typo.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The common adp5520 mfd defines were namespaced to avoid collisions, so
update the define used in this driver accordingly.  The structs were also
renamed to fix a spelling typo.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

88PM8607 depends on I2C and MFD_CORE. Since 88PM8607 is built-in
kernel, it also requires that I2C and MFD_CORE are built-in
kernel also.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The function asic3_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The WM8320 is an integrated power management subsystem providing
voltage regulators, RTC, watchdog and other functionality. The
WM8320 is derived from the WM831x and therefore shares most of
the driver code with the WM831x.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This supports future devices with fewer GPIOs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Better support future device revisions by moving some of the output
around and making the chip ID enumeration be the value expected in
the ID register.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The name field of struct i2c_client is for i2c-core's use, it should
never be changed by the drivers themselves.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When building the driver as a module, module_exit was missing, and
subsys_initcall_sync() is not defined.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This adds core driver support for AB4500 mixed signal
multimedia & power management chip. This connects to U8500
on the SSP (pl022) and exports read/write functions for
the device to get access to this chip. This also registers
the client devices and sets the parent.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Reviewed-by: Mark Brown <broonie@sirena.org.uk>
Reviewed-by: Jean-Christophe <plagnioj@jcrosoft.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This adds a core driver for 88PM8607 found in Marvell DKB development
platform. This driver is a proxy for all accesses to 88PM8607
sub-drivers which will be merged on top of this one, RTC, regulators,
battery and so on.

This chip is manufactured by Marvell.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

* 'ixp4xx' of git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6:
  IXP4xx: GTWX5715 platform only has two PCI IRQ lines, not four.
  IXP4xx: Introduce IXP4XX_GPIO_IRQ(n) macro and convert IXP4xx platform files.
  IXP4xx: move Gemtek GTWX5715 platform macros to the platform code.
  IXP4xx: Remove unused Motorola PrPMC1100 platform macros.
  IXP4xx: move FSG platform macros to the platform code.
  IXP4xx: move DSM G600 platform macros to the platform code.
  IXP4xx: move NAS100D platform macros to the platform code.
  IXP4xx: move NSLU2 platform macros to the platform code.
  IXP4xx: move Coyote platform macros to the platform code.
  IXP4xx: move AVILA platform macros to the platform code.
  IXP4xx: move IXDP425 platform macros to the platform code.
  IXP4xx: Extend PCI MMIO indirect address space to 1 GB.
  IXP4xx: Fix compilation failure with CONFIG_IXP4XX_INDIRECT_PCI.
  IXP4xx: Drop "__ixp4xx_" prefix from in/out/ioread/iowrite functions for clarity.
  IXP4xx: Rename indirect MMIO primitives from __ixp4xx_* to __indirect_*.
  IXP4xx: Ensure index is positive in irq_to_gpio() and npe_request().
  ARM: fix insl() and outsl() endianness on IXP4xx architecture.
  IXP4xx: Fix normally-disabled debugging text in drivers/net/arm/ixp4xx_eth.c.
  IXP4xx: change the timer base frequency to 66.666000 MHz.

As shown by the previous patch (6698e347: "tty: Fix BKL taken under a
spinlock bug introduced in the BKL split") the BKL removal is prone to
some subtle issues, where removing the BKL in one place may in fact make
a previously nested BKL call the new outer call, and then prone to nasty
deadlocks with other spinlocks.

In general, we should never take the BKL while we're holding a spinlock,
so let's just add a "might_sleep()" to it (even though the BKL doesn't
technically sleep - at least not yet), and we'll get nice warnings the
next time this kind of problem happens during BKL removal.
Acked-and-Tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The fasync path takes the BKL (it probably doesn't need to in fact)
while holding the file_list spinlock.  You can't do that with the kernel
lock: it causes lock inversions and deadlocks.

Leave the BKL over that bit for the moment.

Identified by AKPM.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-and-Tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (151 commits)
  powerpc: Fix usage of 64-bit instruction in 32-bit altivec code
  MAINTAINERS: Add PowerPC patterns
  powerpc/pseries: Track previous CPPR values to correctly EOI interrupts
  powerpc/pseries: Correct pseries/dlpar.c build break without CONFIG_SMP
  powerpc: Make "intspec" pointers in irq_host->xlate() const
  powerpc/8xx: DTLB Miss cleanup
  powerpc/8xx: Remove DIRTY pte handling in DTLB Error.
  powerpc/8xx: Start using dcbX instructions in various copy routines
  powerpc/8xx: Restore _PAGE_WRITETHRU
  powerpc/8xx: Add missing Guarded setting in DTLB Error.
  powerpc/8xx: Fixup DAR from buggy dcbX instructions.
  powerpc/8xx: Tag DAR with 0x00f0 to catch buggy instructions.
  powerpc/8xx: Update TLB asm so it behaves as linux mm expects.
  powerpc/8xx: Invalidate non present TLBs
  powerpc/pseries: Serialize cpu hotplug operations during deactivate Vs deallocate
  pseries/pseries: Add code to online/offline CPUs of a DLPAR node
  powerpc: stop_this_cpu: remove the cpu from the online map.
  powerpc/pseries: Add kernel based CPU DLPAR handling
  sysfs/cpu: Add probe/release files
  powerpc/pseries: Kernel DLPAR Infrastructure
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Overwrite pin config on intel DG45ID board.
  intelhdmi - dont power off HDA link
  ALSA: hrtimer - Fix lock-up
  ALSA: intelhdmi - add channel mapping for typical configurations
  ALSA: intelhdmi - channel mapping applies to Pin
  ALSA: intelhdmi - accept DisplayPort pin
  ALSA: hda - show HBR(High Bit Rate) pin cap in procfs
  ALSA: hda - Fix LED GPIO setup for HP laptops with IDT codecs
  ASoC: Fix build of OMAP sound drivers
  ALSA: opti93x: fix irq releasing if the irq cannot be allocated

Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (75 commits)
  omap3: Fix OMAP35XX_REV macros
  omap: serial: fix non-empty uart fifo read abort
  omap3: Zoom2/3: Update hsmmc board config params
  omap3 : Enable TWL4030 Keypad for Zoom2 and Zoom3 boards
  omap3: id code detection 3525 vs 3515
  omap3: rx51: Use wl1251 in SPI mode 3
  omap3: zoom2/3: make MMC slot work again
  omap1: htcherald: Update defconfig to include mux support
  omap1: LCD_DMA: Use some define rather than a hexadecimal
  omap: header: remove unused data-type
  omap: arch/arm/plat-omap/devices.c - sort alphabetically
  omap: Correcting GPMC_CONFIG1_DEVICETYPE_NAND
  OMAP3: serial - allow platforms specify which UARTs to initialize
  omap3: cm-t35: add mux initialization
  OMAP4: Sync up omap4430 defconfig
  OMAP4: Remove the secondary wait loop
  OMAP4: AuxCoreBoot registers only accessible in secure mode
  OMAP4: Fix SRAM base and size
  OMAP4: Fix cpu detection
  omap3: pandora: board file updates for .33
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  be2net: fix error in rx completion processing.
  igbvf: avoid reset storms due to mailbox issues
  igb: fix handling of mailbox collisions between PF/VF
  usb: remove rare pm primitive for conversion to new API