Add bindings doc for Sunplus SoC UART Driver
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com>
Link: https://lore.kernel.org/r/1645522563-17183-2-git-send-email-hammerh0314@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Set em485->active_timer = NULL isn't always enough to take out the stop
timer. While there is a check that it acts in the right state (i.e.
waiting for RTS-after-send to pass after sending some chars) but the
following might happen:

 - CPU1: some chars send, shifter becomes empty, stop tx timer armed
 - CPU0: more chars send before RTS-after-send expired
 - CPU0: shifter empty irq, port lock taken
 - CPU1: tx timer triggers, waits for port lock
 - CPU0: em485->active_timer = &em485->stop_tx_timer, hrtimer_start(),
   releases lock()
 - CPU1: get lock, see em485->active_timer == &em485->stop_tx_timer,
   tear down RTS too early

This fix bases on research done by Steffen Trumtrar.

Fixes: b86f86e8 ("serial: 8250: fix potential deadlock in rs485-mode")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220215160236.344236-1-u.kleine-koenig@pengutronix.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make UART driver compatible with S4 SOC UART.
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-7-yu.tu@amlogic.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: meson: The system stuck when you run the stty command on the console to change the baud rate

Start the console and run the following commands in turn:
stty -F /dev/ttyAML0 115200 and stty -F /dev/ttyAML0 921600. The
system will stuck.
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-6-yu.tu@amlogic.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make the internal clock source mux and divider writeable, allowing the
uart to deviate from the settings intially applied by the ROMCode and
using the most appropriate clocks.
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-5-yu.tu@amlogic.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Using the common Clock code to describe the UART baud rate clock
makes it easier for the UART driver to be compatible with the
baud rate requirements of the UART IP on different meson chips.
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-4-yu.tu@amlogic.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace devm_request_mem_region and devm_ioremap with
devm_ioremap_resource to make the code cleaner.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-3-yu.tu@amlogic.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This simplifies resetting the UART controller during probe
and will make it easier to integrate the common clock code
which will require the registers at probe time as well.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220225073922.3947-2-yu.tu@amlogic.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The code uses uart_amba_port::port on many places. Sometimes it even
needs not uart_amba_port itself. So simplify the code on many places
and remove the need of uart_amba_port on some places completely.

No functional changes intended. The objdump -d output shows only a code
move in pl010_rx_chars().
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Russell King <linux@armlinux.org.uk>
Link: https://lore.kernel.org/r/20220224111028.20917-5-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of open-coding what serial_lpc32xx_stop_tx() already does, call
it in __serial_lpc32xx_tx() directly.

Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224111028.20917-6-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the hello print among with version and name definitions. Drivers
should print nothing if they are successful.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224111028.20917-3-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All these return bitmasks, so it makes more sense to return unsigned --
this is what a reader and also all the callers expect.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220224111028.20917-2-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The pci_get_slot() increases its reference count, the caller
must decrement the reference count by calling pci_dev_put().

Fixes: 9a1870ce ("serial: 8250: don't use slave_id of dma_slave_config")
Depends-on: a13e19cf ("serial: 8250_lpss: split LPSS driver to separate module")
Reported-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220223151240.70248-1-andriy.shevchenko@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The pci_get_slot() increases its reference count, the caller
must decrement the reference count by calling pci_dev_put().

Fixes: 90b9aacf ("serial: 8250_pci: add Intel Tangier support")
Fixes: f549e94e ("serial: 8250_pci: add Intel Penwell ports")
Reported-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Depends-on: d9eda9ba ("serial: 8250_pci: Intel MID UART support to its own driver")
Link: https://lore.kernel.org/r/20220215100920.41984-1-andriy.shevchenko@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

coccinelle report:
./drivers/tty/serial/8250/8250_aspeed_vuart.c:85:8-16:
WARNING: use scnprintf or sprintf
./drivers/tty/serial/8250/8250_aspeed_vuart.c:174:8-16:
WARNING: use scnprintf or sprintf
./drivers/tty/serial/8250/8250_aspeed_vuart.c:127:8-16:
WARNING: use scnprintf or sprintf

Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: David Yang <davidcomponentone@gmail.com>
Link: https://lore.kernel.org/r/fed40753603dac4d14b17970c88e6f5f936348c1.1644541843.git.yang.guang5@zte.com.cnSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct the Kconfig help text for SERIAL_8250_LPSS, SERIAL_8250_MID and
SERIAL_8250_PERICOM configuration options for dedicated PCI UART drivers
that have been blacklisted in the generic PCI 8250 UART driver and as
from commit a13e19cf ("serial: 8250_lpss: split LPSS driver to
separate module"), commit d9eda9ba ("serial: 8250_pci: Intel MID
UART support to its own driver"), and commit fcfd3c09 ("serial:
8250_pci: Split out Pericom driver") respectively are not handled by
said driver anymore (rather than for extra features only, as the current
text indicates), and therefore require the respective dedicated drivers
to work at all.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2202121704560.34636@angie.orcam.me.ukSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Define DT node for UART clock "marvell,armada-3700-uart-clock" and use
this UART clock as a base clock for all UART devices.
Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-7-kabel@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Implement simple usage of fractional divisor. When main divisor D is too
large to represent requested baudrate then use divisor M from the
fractional divisor feature. All the M prescalers are set to the same and
maximal value 63, so the fractional part of the fractional divisor is not
used at all. We also determine upper limit for possible baudrates.

Experiments show that UART at baudrate 1500000 Bd with this configuration
is stable. So there is no need to implement complicated calculation of
fractional coefficients yet.

To use this feature with higher baudrates, it is required to use UART clock
provided by UART clock driver. Default boot xtal clock is not capable of
higher baudrates.
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-6-kabel@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Device "marvell,armada-3700-uart" should use
"marvell,armada-3700-uart-clock" compatible clock.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-5-kabel@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Implement a new device driver for controlling UART clocks on Marvell
Armada 3700 SoC. This device driver is loaded for devices which match
the compatible string "marvell,armada-3700-uart-clock".

There are more pitfalls related to UART clocks:
- both UARTs use same parent clock source (which can be xtal or one of
  the TBG clocks),
- if a TBG clock is used as the parent clock, there are two additional
  divisors that can both be configured to divide the rate by 1, 2, ... 6,
  but these divisors are again shared between the two UART controllers
  on the SOC,
- the configuration of the parent clock source and divisors is done in
  the address space of the first UART controller, UART1. Clocks can be
  gated separately for UART1 and UART2, but this setting also lives in
  the address space of UART1,
- Marvell's Functional Specification for Armada 3720 document has the
  clock gating bits swapped, so the one described to gate UART1 clock
  actually gates UART2 and vice versa,
- each UART has it's own "special divisor", and this uses the parent
  clock described above. These divisors are configure in each UART's
  address space separately.

Thus the driver for UART2 controller needs to have access to UART1
address space, since UART1 address space contains some bits exclusive
for UART2 and also some bits which are shared between UART1 and UART2.

Also, during boot, when early console is active on one of the UARTs,
and we want to switch parent clock from xtal (default) to TBG (to be
more flexible with baudrates), the driver changing UART clocks also
needs to be able to change the "special divisor", so that the baudrate
of earlycon is not changed when swtiching to normal console. Thus the
clock driver also needs to be able to access UART2 register space,
for UART2's "special divisor".

For these reasons, this new UART clock driver does not use
ioremap_resource(), but only ioremap() to prevent resource conflicts
between UART clock driver and UART driver.

We need to share only two 32-bit registers between the UART driver and
the UART clock driver:
- UART Clock Control
- UART 2 Baud Rate Divisor
Access to these two registers are protected by one spinlock to prevent
any conflicts. Access is required only during probing, when changing
baudrate or during suspend/resume.

Hardware can be configured to use one of following clocks as UART parent
clock: TBG-A-P, TBG-B-P, TBG-A-S, TBG-B-S, xtal. Not every clock is
usable for higher buadrates. Any subset can be specified in the
device-tree and the driver will choose the best one which also still
supports the mandatory baudrate of 9600 Bd. For smooth boot log output
it is needed to specify clock used by early console, otherwise garbage
would be printed on UART during probe of UART clock driver and
transitioning from early console to normal console.

We are implementing this to be able to configure TBG clock as UART
parent clock, which is required to be able to achieve higher baudrates
than 230400 Bd. We achieve this by referencing this new UART clock
device node in UART's device node. UART clock device driver
automatically chooses the best clock source for UART driver.

Until now, UART's device-tree node needed to reference one of the static
clocks (xtal or one of the TBGs) as parent clock in the `clocks`
phandle - the parent clock which was configured before booting the
kernel. If bootloader changed UART's parent clock, it needed to change
the `clocks` phandle in DTB correspondingly before booting.

From now on both the old mechanism (xtal or TBG referenced as parent
clock in `clocks` phandle) and the new one (UART clock referenced in the
`clocks` phandle) are supported, to provide full backward compatibility
with existing DTS files, full backward compatibility with existing boot
loaders, and to provide new features (runtime clock configuration to
allow higher baudrates than 230400 Bd). New features are available only
with new DTS files.

There was also a discussion about how the UART node and the
clock-controller node could be wrapped together in a new binding [1, 2].
As explained there, this is not possible if we want to keep backwards
compatibility with existing bootloaders, and thus we are doing this by
putting the UART clock-controller node inside the UART1 node.

[1] https://lore.kernel.org/linux-serial/20220120000651.in7s6nazif5qjkme@pali/
[2] https://lore.kernel.org/linux-serial/20220125204006.A6D09C340E0@smtp.kernel.org/Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-4-kabel@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add DT bindings documentation for device nodes with compatible string
"marvell,armada-3700-uart-clock".
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-3-kabel@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Provide DIV_U64_ROUND_CLOSEST helper which uses div_u64 to perform
division rounded to the closest integer using unsigned 64bit
dividend and unsigned 32bit divisor.
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220219152818.4319-2-kabel@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Export only the GPIOs that are not shared with hardware modem control
lines. Introduce new device parameter indicating whether modem control
lines are available.
Signed-off-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220221105618.3503470-4-tomasz.mon@camlingroup.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RTS, DTR and LOOP bits can be updated in a single MCR register update.
This reduces the number of (slow) SPI/I2C bus transactions.
Signed-off-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220221105618.3503470-3-tomasz.mon@camlingroup.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Preserve unaffected bits state when accessing EFR register. This
prevents hardware flow control bits from being cleared on enhanced
functions access.
Signed-off-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220221105618.3503470-2-tomasz.mon@camlingroup.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Don't start the whole chain for TX if there is no data to send. This is
mostly relevant for rs485 mode as there might be rts-before-send and
rts-after-send delays involved.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220217211839.443039-1-u.kleine-koenig@pengutronix.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add Pali Rohár as mvebu-uart.c maintainer
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220222105406.28894-1-pali@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove arch specific termbits.h as there are only trivial space
differences between include/uapi/asm-generic/termbits.h and
arch/xtensa/include/uapi/asm/termbits.h.

$ diff -u0 -b -B include/uapi/asm-generic/termbits.h arch/xtensa/include/uapi/asm/termbits.h
. --- include/uapi/asm-generic/termbits.h       2022-01-10 13:44:42.814107461 +0200
. +++ arch/xtensa/include/uapi/asm/termbits.h   2022-01-10 13:44:42.690106926 +0200
. @@ -2,2 +2,15 @@
. -#ifndef __ASM_GENERIC_TERMBITS_H
. -#define __ASM_GENERIC_TERMBITS_H
. +/*
. + * include/asm-xtensa/termbits.h
. + *
. + * Copied from SH.
. + *
. + * This file is subject to the terms and conditions of the GNU General Public
. + * License.  See the file "COPYING" in the main directory of this archive
. + * for more details.
. + *
. + * Copyright (C) 2001 - 2005 Tensilica Inc.
. + */
. +
. +#ifndef _XTENSA_TERMBITS_H
. +#define _XTENSA_TERMBITS_H
. +
. @@ -200 +221 @@
. -#endif /* __ASM_GENERIC_TERMBITS_H */
. +#endif /* _XTENSA_TERMBITS_H */
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220222115604.7351-3-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove arch specific termbits.h as there are only trivial space
differences between include/uapi/asm-generic/termbits.h and
arch/ia64/include/uapi/asm/termbits.h:

$ diff -u0 -b -B include/uapi/asm-generic/termbits.h arch/ia64/include/uapi/asm/termbits.h
. --- include/uapi/asm-generic/termbits.h         2022-01-10 13:44:42.814107461 +0200
. +++ arch/ia64/include/uapi/asm/termbits.h       2022-01-10 13:44:42.678106874 +0200
. @@ -2,2 +2,11 @@
. -#ifndef __ASM_GENERIC_TERMBITS_H
. -#define __ASM_GENERIC_TERMBITS_H
. +#ifndef _ASM_IA64_TERMBITS_H
. +#define _ASM_IA64_TERMBITS_H
. +
. +/*
. + * Based on <asm-i386/termbits.h>.
. + *
. + * Modified 1999
. + *     David Mosberger-Tang <davidm@hpl.hp.com>, Hewlett-Packard Co
. + *
. + * 99/01/28    Added new baudrates
. + */
. @@ -200 +209 @@
. -#endif /* __ASM_GENERIC_TERMBITS_H */
. +#endif /* _ASM_IA64_TERMBITS_H */
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220222115604.7351-2-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 54da3e38 ("serial: 8250_aspeed_vuart: use UPF_IOREMAP to
set up register mapping") fixed a bug that had, as a side-effect,
prevented the 8250_aspeed_vuart driver from enabling the VUART's
FIFOs.  However, fixing that (and hence enabling the FIFOs) has in
turn revealed what appears to be a hardware bug in the ASPEED VUART in
which the host-side THRE bit doesn't get if the BMC-side receive FIFO
trigger level is set to anything but one byte.  This causes problems
for polled-mode writes from the host -- for example, Linux kernel
console writes proceed at a glacial pace (less than 100 bytes per
second) because the write path waits for a 10ms timeout to expire
after every character instead of being able to continue on to the next
character upon seeing THRE asserted.  (GRUB behaves similarly.)

As a workaround, introduce a new port type for the ASPEED VUART that's
identical to PORT_16550A as it had previously been using, but with
UART_FCR_R_TRIG_00 instead to set the receive FIFO trigger level to
one byte, which (experimentally) seems to avoid the problematic THRE
behavior.

Fixes: 54da3e38 ("serial: 8250_aspeed_vuart: use UPF_IOREMAP to set up register mapping")
Tested-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20220211004203.14915-1-zev@bewilderbeest.netSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All supported platforms by this driver require ->setup() and ->exit().
Remove unneeded test for ->setup() presence.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220215101111.47250-1-andriy.shevchenko@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since PCI core provides a generic PCI_DEVICE_DATA() macro,
replace MID_DEVICE() with former one.

No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220215104126.7220-1-andriy.shevchenko@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

"a * (1 << b)" == "a << b".

No change in generated code.
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/118d62e167f6cf5e98bdf9a738634b4590ea8d09.1645460901.git.geert+renesas@glider.beSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add early console support which relies on the bootloader for the
initialization of the UART.
Please note, that the compatibles are taken from at91-usart MFD
driver.
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220217094620.1148571-1-michael@walle.ccSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'kbuild-fixes-v5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Fix the truncated path issue for HAVE_GCC_PLUGINS test in Kconfig

 - Move -Wunsligned-access to W=1 builds to avoid sprinkling warnings
   for the latest Clang

 - Fix missing fclose() in Kconfig

 - Fix Kconfig to touch dep headers correctly when KCONFIG_AUTOCONFIG is
   overridden.

* tag 'kbuild-fixes-v5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: fix failing to generate auto.conf
  kconfig: fix missing fclose() on error paths
  Makefile.extrawarn: Move -Wunaligned-access to W=1
  kconfig: let 'shell' return enough output for deep path names

Pull irq fixes from Thomas Gleixner:
 "Interrupt chip driver fixes:

   - Don't install an hotplug notifier for GICV3-ITS on systems which do
     not need it to prevent a warning in the notifier about inconsistent
     state

   - Add the missing device tree matching for the T-HEAD PLIC variant so
     the related SoC is properly supported"

* tag 'irq-urgent-2022-02-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/sifive-plic: Add missing thead,c900-plic match string
  dt-bindings: update riscv plic compatible string
  irqchip/gic-v3-its: Skip HP notifier when no ITS is registered

Pull objtool fix from Borislav Petkov:
 "Fix a case where objtool would mistakenly warn about instructions
  being unreachable"

* tag 'objtool_urgent_for_v5.17_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/bug: Merge annotate_reachable() into _BUG_FLAGS() asm

Pull scheduler fix from Borislav Petkov:
 "Fix a NULL-ptr dereference when recalculating a sched entity's weight"

* tag 'sched_urgent_for_v5.17_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Fix fault in reweight_entity