- 14 Jun, 2017 40 commits
-
-
Sui Chen authored
commit 8bfd1743 upstream. (Correction in this resend: fixed function name acer_sa5_271_workaround; fixed the always-true condition in the function; fixed description.) On the Acer Switch Alpha 12 (model number: SA5-271), the internal SSD may not get detected because the port_map and CAP.nr_ports combination causes the driver to skip the port that is actually connected to the SSD. More specifically, either all SATA ports are identified as DUMMY, or all ports get ``link down'' and never get up again. This problem occurs occasionally. When this problem occurs, CAP may hold a value of 0xC734FF00 or 0xC734FF01 and port_map may hold a value of 0x00 or 0x01. When this problem does not occur, CAP holds a value of 0xC734FF02 and port_map may hold a value of 0x07. Overriding the CAP value to 0xC734FF02 and port_map to 0x7 significantly reduces the occurrence of this problem. Link: https://bugzilla.kernel.org/attachment.cgi?id=253091Signed-off-by:
Sui Chen <suichen6@gmail.com> Tested-by:
Damian Ivanov <damianatorrpm@gmail.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Eric Anholt authored
commit 43523eba upstream. Without this, polling on the dma-buf (and presumably other devices synchronizing against our rendering) would return immediately, even while the BO was busy. Signed-off-by:
Eric Anholt <eric@anholt.net> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Rob Clark <robdclark@gmail.com> Cc: linux-arm-msm@vger.kernel.org Cc: freedreno@lists.freedesktop.org Reviewed-by:
Rob Clark <robdclark@gmail.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 4ff83daa upstream. During v4.3 when the overflow/underflow check was relaxed by commit c72c5250: commit c72c5250 Author: Roland Dreier <roland@purestorage.com> Date: Wed Jul 22 15:08:18 2015 -0700 target: allow underflow/overflow for PR OUT etc. commands to allow underflow/overflow for Windows compliance + FCP, a consequence was to allow control CDBs to process overflow data for iscsi-target with immediate data as well. As per Roland's original change, continue to allow underflow cases for control CDBs to make Windows compliance + FCP happy, but until overflow for control CDBs is supported tree-wide, explicitly reject all control WRITEs with overflow following pre v4.3.y logic. Reported-by:
Bart Van Assche <bart.vanassche@sandisk.com> Cc: Roland Dreier <roland@purestorage.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
David Arcari authored
commit 6c770036 upstream. For a driver that does not set the CPUFREQ_STICKY flag, if all of the ->init() calls fail, cpufreq_register_driver() should return an error. This will prevent the driver from loading. Fixes: ce1bcfe9 (cpufreq: check cpufreq_policy_list instead of scanning policies for all CPUs) Signed-off-by:
David Arcari <darcari@redhat.com> Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Pratyush Anand authored
commit 6f9193ec upstream. modprobe is not able to resolve sysfs modalias for mei devices. # cat /sys/class/watchdog/watchdog0/device/watchdog/watchdog0/device/modalias mei::05b79a6f-4628-4d7f-899d-a91514cb32ab: # modprobe --set-version 4.9.6-200.fc25.x86_64 -R mei::05b79a6f-4628-4d7f-899d-a91514cb32ab: modprobe: FATAL: Module mei::05b79a6f-4628-4d7f-899d-a91514cb32ab: not found in directory /lib/modules/4.9.6-200.fc25.x86_64 # cat /lib/modules/4.9.6-200.fc25.x86_64/modules.alias | grep 05b79a6f-4628-4d7f-899d-a91514cb32ab alias mei:*:05b79a6f-4628-4d7f-899d-a91514cb32ab:*:* mei_wdt commit b26864ca ("mei: bus: add client protocol version to the device alias"), however sysfs modalias is still in formmat mei:S:uuid:*. This patch equates format of uevent and sysfs modalias so that modprobe is able to resolve the aliases. Fixes: commit b26864ca ("mei: bus: add client protocol version to the device alias") Signed-off-by:
Pratyush Anand <panand@redhat.com> Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
-
Matt Ranostay authored
commit 9122b54f upstream. Using iio_trigger_poll() can oops when multiple interrupts happen before the first is handled. Use iio_trigger_poll_chained() instead and use the timestamp when processed, since it will be in theory be 2 ms max latency. Fixes: 24ddb0e4 ("iio: Add AS3935 lightning sensor support") Signed-off-by:
Matt Ranostay <matt.ranostay@konsulko.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Matt Ranostay authored
commit 275292d3 upstream. AS3935 interrupt mask has been incorrect so valid lightning events would never trigger an buffer event. Also noise interrupt should be BIT(0). Fixes: 24ddb0e4 ("iio: Add AS3935 lightning sensor support") Signed-off-by:
-
Franziska Naepelt authored
commit 7cc3bff4 upstream. The register mapping for the IIO driver for the Liteon Light and Proximity sensor LTR501 interrupt mode is interchanged (ALS/PS). There is a register called INTERRUPT register (address 0x8F) Bit 0 represents PS measurement trigger. Bit 1 represents ALS measurement trigger. This two bit fields are interchanged within the driver. see datasheet page 24: http://optoelectronics.liteon.com/upload/download/DS86-2012-0006/S_110_LTR-501ALS-01_PrelimDS_ver1%5B1%5D.pdfSigned-off-by:
Franziska Naepelt <franziska.naepelt@idt.com> Fixes: 7ac702b3 ("iio: ltr501: Add interrupt support") Acked-by:
Peter Meerwald-Stadler <pmeerw@pmeerw.net> Signed-off-by:
-
Raveendra Padasalagi authored
commit f7d86ecf upstream. The third argument of devm_request_threaded_irq() is the primary handler. It is called in hardirq context and checks whether the interrupt is relevant to the device. If the primary handler returns IRQ_WAKE_THREAD, the secondary handler (a.k.a. handler thread) is scheduled to run in process context. bcm_iproc_adc.c uses the secondary handler as the primary one and the other way around. So this patch fixes the same, along with re-naming the secondary handler and primary handler names properly. Tested on the BCM9583XX iProc SoC based boards. Fixes: 4324c97e ("iio: Add driver for Broadcom iproc-static-adc") Reported-by:
Pavel Roskin <plroskin@gmail.com> Signed-off-by:
Raveendra Padasalagi <raveendra.padasalagi@broadcom.com> Signed-off-by:
-
Oleg Drokin authored
commit 0a33252e upstream. lov_getstripe() calls set_fs(KERNEL_DS) so that it can handle a struct lov_user_md pointer from user- or kernel-space. This changes the behavior of copy_from_user() on SPARC and may result in a misaligned access exception which in turn oopses the kernel. In fact the relevant argument to lov_getstripe() is never called with a kernel-space pointer and so changing the address limits is unnecessary and so we remove the calls to save, set, and restore the address limits. Signed-off-by:
John L. Hammond <john.hammond@intel.com> Reviewed-on: http://review.whamcloud.com/6150 Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3221Reviewed-by:
Andreas Dilger <andreas.dilger@intel.com> Reviewed-by:
Li Wei <wei.g.li@intel.com> Signed-off-by:
Oleg Drokin <green@linuxhacker.ru> Signed-off-by:
-
Michael Thalmeier authored
commit 0340ff83 upstream. ci_role BUGs when the role is >= CI_ROLE_END. Signed-off-by:
Michael Thalmeier <michael.thalmeier@hale.at> Signed-off-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
-
Jisheng Zhang authored
commit aa1f058d upstream. Fix below NULL pointer dereference. we set ci->roles[CI_ROLE_GADGET] too early in ci_hdrc_gadget_init(), if udc_start() fails due to some reason, the ci->roles[CI_ROLE_GADGET] check in ci_hdrc_gadget_destroy can't protect us. We fix this issue by only setting ci->roles[CI_ROLE_GADGET] if udc_start() succeed. [ 1.398550] Unable to handle kernel NULL pointer dereference at virtual address 00000000 ... [ 1.448600] PC is at dma_pool_free+0xb8/0xf0 [ 1.453012] LR is at dma_pool_free+0x28/0xf0 [ 2.113369] [<ffffff80081817d8>] dma_pool_free+0xb8/0xf0 [ 2.118857] [<ffffff800841209c>] destroy_eps+0x4c/0x68 [ 2.124165] [<ffffff8008413770>] ci_hdrc_gadget_destroy+0x28/0x50 [ 2.130461] [<ffffff800840fa30>] ci_hdrc_probe+0x588/0x7e8 [ 2.136129] [<ffffff8008380fb8>] platform_drv_probe+0x50/0xb8 [ 2.142066] [<ffffff800837f494>] driver_probe_device+0x1fc/0x2a8 [ 2.148270] [<ffffff800837f68c>] __device_attach_driver+0x9c/0xf8 [ 2.154563] [<ffffff800837d570>] bus_for_each_drv+0x58/0x98 [ 2.160317] [<ffffff800837f174>] __device_attach+0xc4/0x138 [ 2.166072] [<ffffff800837f738>] device_initial_probe+0x10/0x18 [ 2.172185] [<ffffff800837e58c>] bus_probe_device+0x94/0xa0 [ 2.177940] [<ffffff800837c560>] device_add+0x3f0/0x560 [ 2.183337] [<ffffff8008380d20>] platform_device_add+0x180/0x240 [ 2.189541] [<ffffff800840f0e8>] ci_hdrc_add_device+0x440/0x4f8 [ 2.195654] [<ffffff8008414194>] ci_hdrc_usb2_probe+0x13c/0x2d8 [ 2.201769] [<ffffff8008380fb8>] platform_drv_probe+0x50/0xb8 [ 2.207705] [<ffffff800837f494>] driver_probe_device+0x1fc/0x2a8 [ 2.213910] [<ffffff800837f5ec>] __driver_attach+0xac/0xb0 [ 2.219575] [<ffffff800837d4b0>] bus_for_each_dev+0x60/0xa0 [ 2.225329] [<ffffff800837ec80>] driver_attach+0x20/0x28 [ 2.230816] [<ffffff800837e880>] bus_add_driver+0x1d0/0x238 [ 2.236571] [<ffffff800837fdb0>] driver_register+0x60/0xf8 [ 2.242237] [<ffffff8008380ef4>] __platform_driver_register+0x44/0x50 [ 2.248891] [<ffffff80086fd440>] ci_hdrc_usb2_driver_init+0x18/0x20 [ 2.255365] [<ffffff8008082950>] do_one_initcall+0x38/0x128 [ 2.261121] [<ffffff80086e0d00>] kernel_init_freeable+0x1ac/0x250 [ 2.267414] [<ffffff800852f0b8>] kernel_init+0x10/0x100 [ 2.272810] [<ffffff8008082680>] ret_from_fork+0x10/0x50 Fixes: 3f124d23 ("usb: chipidea: add role init and destroy APIs") Signed-off-by:
Jisheng Zhang <jszhang@marvell.com> Signed-off-by:
-
Thinh Nguyen authored
commit dc9217b6 upstream. f_mass_storage has a memorry barrier issue with the sleep and wake functions that can cause a deadlock. This results in intermittent hangs during MSC file transfer. The host will reset the device after receiving no response to resume the transfer. This issue is seen when dwc3 is processing 2 transfer-in-progress events at the same time, invoking completion handlers for CSW and CBW. Also this issue occurs depending on the system timing and latency. To increase the chance to hit this issue, you can force dwc3 driver to wait and process those 2 events at once by adding a small delay (~100us) in dwc3_check_event_buf() whenever the request is for CSW and read the event count again. Avoid debugging with printk and ftrace as extra delays and memory barrier will mask this issue. Scenario which can lead to failure: ----------------------------------- 1) The main thread sleeps and waits for the next command in get_next_command(). 2) bulk_in_complete() wakes up main thread for CSW. 3) bulk_out_complete() tries to wake up the running main thread for CBW. 4) thread_wakeup_needed is not loaded with correct value in sleep_thread(). 5) Main thread goes to sleep again. The pattern is shown below. Note the 2 critical variables. * common->thread_wakeup_needed * bh->state CPU 0 (sleep_thread) CPU 1 (wakeup_thread) ============================== =============================== bh->state = BH_STATE_FULL; smp_wmb(); thread_wakeup_needed = 0; thread_wakeup_needed = 1; smp_rmb(); if (bh->state != BH_STATE_FULL) sleep again ... As pointed out by Alan Stern, this is an R-pattern issue. The issue can be seen when there are two wakeups in quick succession. The thread_wakeup_needed can be overwritten in sleep_thread, and the read of the bh->state maybe reordered before the write to thread_wakeup_needed. This patch applies full memory barrier smp_mb() in both sleep_thread() and wakeup_thread() to ensure the order which the thread_wakeup_needed and bh->state are written and loaded. However, a better solution in the future would be to use wait_queue method that takes care of managing memory barrier between waker and waiter. Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Thinh Nguyen <thinhn@synopsys.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Hans de Goede authored
commit 75fb6363 upstream. commit a39be606 ("drm: Do a full device unregister when unplugging") causes backtraces like this one when unplugging an usb drm device while it is in use: usb 2-3: USB disconnect, device number 25 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 242 at drivers/gpu/drm/drm_mode_config.c:424 drm_mode_config_cleanup+0x220/0x280 [drm] ... RIP: 0010:drm_mode_config_cleanup+0x220/0x280 [drm] ... Call Trace: gm12u320_modeset_cleanup+0xe/0x10 [gm12u320] gm12u320_driver_unload+0x35/0x70 [gm12u320] drm_dev_unregister+0x3c/0xe0 [drm] drm_unplug_dev+0x12/0x60 [drm] gm12u320_usb_disconnect+0x36/0x40 [gm12u320] usb_unbind_interface+0x72/0x280 device_release_driver_internal+0x158/0x210 device_release_driver+0x12/0x20 bus_remove_device+0x104/0x180 device_del+0x1d2/0x350 usb_disable_device+0x9f/0x270 usb_disconnect+0xc6/0x260 ... [drm:drm_mode_config_cleanup [drm]] *ERROR* connector Unknown-1 leaked! ------------[ cut here ]------------ WARNING: CPU: 0 PID: 242 at drivers/gpu/drm/drm_mode_config.c:458 drm_mode_config_cleanup+0x268/0x280 [drm] ... <same Call Trace> ---[ end trace 80df975dae439ed6 ]--- general protection fault: 0000 [#1] SMP ... Call Trace: ? __switch_to+0x225/0x450 drm_mode_rmfb_work_fn+0x55/0x70 [drm] process_one_work+0x193/0x3c0 worker_thread+0x4a/0x3a0 ... RIP: drm_framebuffer_remove+0x62/0x3f0 [drm] RSP: ffffb776c39dfd98 ---[ end trace 80df975dae439ed7 ]--- After which the system is unusable this is caused by drm_dev_unregister getting called immediately on unplug, which calls the drivers unload function which calls drm_mode_config_cleanup which removes the framebuffer object while userspace is still holding a reference to it. Reverting commit a39be606 ("drm: Do a full device unregister when unplugging") leads to the following oops on unplug instead, when userspace closes the last fd referencing the drm_dev: sysfs group 'power' not found for kobject 'card1-Unknown-1' ------------[ cut here ]------------ WARNING: CPU: 0 PID: 2459 at fs/sysfs/group.c:237 sysfs_remove_group+0x80/0x90 ... RIP: 0010:sysfs_remove_group+0x80/0x90 ... Call Trace: dpm_sysfs_remove+0x57/0x60 device_del+0xfd/0x350 device_unregister+0x1a/0x60 drm_sysfs_connector_remove+0x39/0x50 [drm] drm_connector_unregister+0x5a/0x70 [drm] drm_connector_unregister_all+0x45/0xa0 [drm] drm_modeset_unregister_all+0x12/0x30 [drm] drm_dev_unregister+0xca/0xe0 [drm] drm_put_dev+0x32/0x60 [drm] drm_release+0x2f3/0x380 [drm] __fput+0xdf/0x1e0 ... ---[ end trace ecfb91ac85688bbe ]--- BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8 IP: down_write+0x1f/0x40 ... Call Trace: debugfs_remove_recursive+0x55/0x1b0 drm_debugfs_connector_remove+0x21/0x40 [drm] drm_connector_unregister+0x62/0x70 [drm] drm_connector_unregister_all+0x45/0xa0 [drm] drm_modeset_unregister_all+0x12/0x30 [drm] drm_dev_unregister+0xca/0xe0 [drm] drm_put_dev+0x32/0x60 [drm] drm_release+0x2f3/0x380 [drm] __fput+0xdf/0x1e0 ... ---[ end trace ecfb91ac85688bbf ]--- This is caused by the revert moving back to drm_unplug_dev calling drm_minor_unregister which does: device_del(minor->kdev); dev_set_drvdata(minor->kdev, NULL); /* safety belt */ drm_debugfs_cleanup(minor); Causing the sysfs entries to already be removed even though we still have references to them in e.g. drm_connector. Note we must call drm_minor_unregister to notify userspace of the unplug of the device, so calling drm_dev_unregister is not completely wrong the problem is that drm_dev_unregister does too much. This commit fixes drm_unplug_dev by not only reverting commit a39be606 ("drm: Do a full device unregister when unplugging") but by also adding a call to drm_modeset_unregister_all before the drm_minor_unregister calls to make sure all sysfs entries are removed before calling device_del(minor->kdev) thereby also fixing the second set of oopses caused by just reverting the commit. Fixes: a39be606 ("drm: Do a full device unregister when unplugging") Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jeffy <jeffy.chen@rock-chips.com> Cc: Marco Diego Aurélio Mesquita <marcodiegomesquita@gmail.com> Reported-by:
Marco Diego Aurélio Mesquita <marcodiegomesquita@gmail.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Sean Paul <seanpaul@chromium.org> Link: http://patchwork.freedesktop.org/patch/msgid/20170601115430.4113-1-hdegoede@redhat.comSigned-off-by:
-
Jan Kara authored
commit 67a7d5f5 upstream. Currently, extent manipulation operations such as hole punch, range zeroing, or extent shifting do not record the fact that file data has changed and thus fdatasync(2) has a work to do. As a result if we crash e.g. after a punch hole and fdatasync, user can still possibly see the punched out data after journal replay. Test generic/392 fails due to these problems. Fix the problem by properly marking that file data has changed in these operations. Fixes: a4bb6b64Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Jan Kara authored
commit 4f8caa60 upstream. When ext4_map_blocks() is called with EXT4_GET_BLOCKS_ZERO to zero-out allocated blocks and these blocks are actually converted from unwritten extent the following race can happen: CPU0 CPU1 page fault page fault ... ... ext4_map_blocks() ext4_ext_map_blocks() ext4_ext_handle_unwritten_extents() ext4_ext_convert_to_initialized() - zero out converted extent ext4_zeroout_es() - inserts extent as initialized in status tree ext4_map_blocks() ext4_es_lookup_extent() - finds initialized extent write data ext4_issue_zeroout() - zeroes out new extent overwriting data This problem can be reproduced by generic/340 for the fallocated case for the last block in the file. Fix the problem by avoiding zeroing out the area we are mapping with ext4_map_blocks() in ext4_ext_convert_to_initialized(). It is pointless to zero out this area in the first place as the caller asked us to convert the area to initialized because he is just going to write data there before the transaction finishes. To achieve this we delete the special case of zeroing out full extent as that will be handled by the cases below zeroing only the part of the extent that needs it. We also instruct ext4_split_extent() that the middle of extent being split contains data so that ext4_split_extent_at() cannot zero out full extent in case of ENOSPC. Fixes: 12735f88Signed-off-by:
-
Konstantin Khlebnikov authored
commit 887a9730 upstream. ext4_expand_extra_isize() should clear only space between old and new size. Fixes: 6dd4ee7c # v2.6.23 Signed-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by:
-
Jan Kara authored
commit 7d95eddf upstream. Currently, SEEK_HOLE implementation in ext4 may both return that there's a hole at some offset although that offset already has data and skip some holes during a search for the next hole. The first problem is demostrated by: xfs_io -c "falloc 0 256k" -c "pwrite 0 56k" -c "seek -h 0" file wrote 57344/57344 bytes at offset 0 56 KiB, 14 ops; 0.0000 sec (2.054 GiB/sec and 538461.5385 ops/sec) Whence Result HOLE 0 Where we can see that SEEK_HOLE wrongly returned offset 0 as containing a hole although we have written data there. The second problem can be demonstrated by: xfs_io -c "falloc 0 256k" -c "pwrite 0 56k" -c "pwrite 128k 8k" -c "seek -h 0" file wrote 57344/57344 bytes at offset 0 56 KiB, 14 ops; 0.0000 sec (1.978 GiB/sec and 518518.5185 ops/sec) wrote 8192/8192 bytes at offset 131072 8 KiB, 2 ops; 0.0000 sec (2 GiB/sec and 500000.0000 ops/sec) Whence Result HOLE 139264 Where we can see that hole at offsets 56k..128k has been ignored by the SEEK_HOLE call. The underlying problem is in the ext4_find_unwritten_pgoff() which is just buggy. In some cases it fails to update returned offset when it finds a hole (when no pages are found or when the first found page has higher index than expected), in some cases conditions for detecting hole are just missing (we fail to detect a situation where indices of returned pages are not contiguous). Fix ext4_find_unwritten_pgoff() to properly detect non-contiguous page indices and also handle all cases where we got less pages then expected in one place and handle it properly there. Fixes: c8c0df24 CC: Zheng Liu <wenqing.lz@taobao.com> Signed-off-by:
-
Julien Grall authored
commit 753c09b5 upstream. Commit 5995a68a "xen/privcmd: Add support for Linux 64KB page granularity" did not go far enough to support 64KB in mmap_batch_fn. The variable 'nr' is the number of 4KB chunk to map. However, when Linux is using 64KB page granularity the array of pages (vma->vm_private_data) contain one page per 64KB. Fix it by incrementing st->index correctly. Furthermore, st->va is not correctly incremented as PAGE_SIZE != XEN_PAGE_SIZE. Fixes: 5995a68a ("xen/privcmd: Add support for Linux 64KB page granularity") Reported-by:
Feng Kan <fkan@apm.com> Signed-off-by:
Julien Grall <julien.grall@arm.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
-
Hou Tao authored
commit 5be6b756 upstream. When adding a cfq_group into the cfq service tree, we use CFQ_IDLE_DELAY as the delay of cfq_group's vdisktime if there have been other cfq_groups already. When cfq is under iops mode, commit 9a7f38c4 ("cfq-iosched: Convert from jiffies to nanoseconds") could result in a large iops delay and lead to an abnormal io schedule delay for the added cfq_group. To fix it, we just need to revert to the old CFQ_IDLE_DELAY value: HZ / 5 when iops mode is enabled. Despite having the same value, the delay of a cfq_queue in idle class and the delay of cfq_group are different things, so I define two new macros for the delay of a cfq_group under time-slice mode and iops mode. Fixes: 9a7f38c4 ("cfq-iosched: Convert from jiffies to nanoseconds") Signed-off-by:
Hou Tao <houtao1@huawei.com> Acked-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Thomas Petazzoni authored
commit b2d3c270 upstream. The XORv2 engine on Armada 7K/8K can only access the first 40 bits of the physical address space, so the DMA mask must be set accordingly. Fixes: 19a340b1 ("dmaengine: mv_xor_v2: new driver") Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Thomas Petazzoni authored
commit 9dd4f319 upstream. The current implementation of interrupt coalescing doesn't work, because it doesn't configure the coalescing timer, which is needed to make sure we get an interrupt at some point. As a fix for stable, we simply remove the interrupt coalescing functionality. It will be re-introduced properly in a future commit. Fixes: 19a340b1 ("dmaengine: mv_xor_v2: new driver") Signed-off-by:
-
Thomas Petazzoni authored
commit 44d5887a upstream. The mv_xor_v2_tx_submit() gets the next available HW descriptor by calling mv_xor_v2_get_desq_write_ptr(), which reads a HW register telling the next available HW descriptor. This was working fine when HW descriptors were issued for processing directly in tx_submit(). However, as part of the review process of the driver, a change was requested to move the actual kick-off of HW descriptors processing to ->issue_pending(). Due to this, reading the HW register to know the next available HW descriptor no longer works. So instead of using this HW register, we implemented a software index pointing to the next available HW descriptor. Fixes: 19a340b1 ("dmaengine: mv_xor_v2: new driver") Signed-off-by:
-
Hanna Hawa authored
commit ab2c5f0a upstream. The engine was enabled prior to its configuration, which isn't correct. This patch relocates the activation of the XOR engine, to be after the configuration of the XOR engine. Fixes: 19a340b1 ("dmaengine: mv_xor_v2: new driver") Signed-off-by:
Hanna Hawa <hannah@marvell.com> Signed-off-by:
-
Thomas Petazzoni authored
commit bc473da1 upstream. Descriptors that have not been acknowledged by the async_tx layer should not be re-used, so this commit adjusts the implementation of mv_xor_v2_prep_sw_desc() to skip descriptors for which async_tx_test_ack() is false. Fixes: 19a340b1 ("dmaengine: mv_xor_v2: new driver") Signed-off-by:
-
Thomas Petazzoni authored
commit 2aab4e18 upstream. mv_xor_v2_tasklet() is looping over completed HW descriptors. Before the loop, it initializes 'next_pending_hw_desc' to the first HW descriptor to handle, and then the loop simply increments this point, without taking care of wrapping when we reach the last HW descriptor. The 'pending_ptr' index was being wrapped back to 0 at the end, but it wasn't used in each iteration of the loop to calculate next_pending_hw_desc. This commit fixes that, and makes next_pending_hw_desc a variable local to the loop itself. Fixes: 19a340b1 ("dmaengine: mv_xor_v2: new driver") Signed-off-by:
-
Thomas Petazzoni authored
commit eb8df543 upstream. The mv_xor_v2_prep_sw_desc() is called from a few different places in the driver, but we never take into account the fact that it might return NULL. This commit fixes that, ensuring that we don't panic if there are no more descriptors available. Fixes: 19a340b1 ("dmaengine: mv_xor_v2: new driver") Signed-off-by:
-
Alexander Sverdlin authored
commit 98f9de36 upstream. Draining the transfers in terminate_all callback happens with IRQs disabled, therefore induces huge latency: irqsoff latency trace v1.1.5 on 4.11.0 -------------------------------------------------------------------- latency: 39770 us, #57/57, CPU#0 | (M:preempt VP:0, KP:0, SP:0 HP:0) ----------------- | task: process-129 (uid:0 nice:0 policy:2 rt_prio:50) ----------------- => started at: _snd_pcm_stream_lock_irqsave => ended at: snd_pcm_stream_unlock_irqrestore _------=> CPU# / _-----=> irqs-off | / _----=> need-resched || / _---=> hardirq/softirq ||| / _--=> preempt-depth |||| / delay cmd pid ||||| time | caller \ / ||||| \ | / process-129 0d.s. 3us : _snd_pcm_stream_lock_irqsave process-129 0d.s1 9us : snd_pcm_stream_lock <-_snd_pcm_stream_lock_irqsave process-129 0d.s1 15us : preempt_count_add <-snd_pcm_stream_lock process-129 0d.s2 22us : preempt_count_add <-snd_pcm_stream_lock process-129 0d.s3 32us : snd_pcm_update_hw_ptr0 <-snd_pcm_period_elapsed process-129 0d.s3 41us : soc_pcm_pointer <-snd_pcm_update_hw_ptr0 process-129 0d.s3 50us : dmaengine_pcm_pointer <-soc_pcm_pointer process-129 0d.s3 58us+: snd_dmaengine_pcm_pointer_no_residue <-dmaengine_pcm_pointer process-129 0d.s3 96us : update_audio_tstamp <-snd_pcm_update_hw_ptr0 process-129 0d.s3 103us : snd_pcm_update_state <-snd_pcm_update_hw_ptr0 process-129 0d.s3 112us : xrun <-snd_pcm_update_state process-129 0d.s3 119us : snd_pcm_stop <-xrun process-129 0d.s3 126us : snd_pcm_action <-snd_pcm_stop process-129 0d.s3 134us : snd_pcm_action_single <-snd_pcm_action process-129 0d.s3 141us : snd_pcm_pre_stop <-snd_pcm_action_single process-129 0d.s3 150us : snd_pcm_do_stop <-snd_pcm_action_single process-129 0d.s3 157us : soc_pcm_trigger <-snd_pcm_do_stop process-129 0d.s3 166us : snd_dmaengine_pcm_trigger <-soc_pcm_trigger process-129 0d.s3 175us : ep93xx_dma_terminate_all <-snd_dmaengine_pcm_trigger process-129 0d.s3 182us : preempt_count_add <-ep93xx_dma_terminate_all process-129 0d.s4 189us*: m2p_hw_shutdown <-ep93xx_dma_terminate_all process-129 0d.s4 39472us : m2p_hw_setup <-ep93xx_dma_terminate_all ... rest skipped... process-129 0d.s. 40080us : <stack trace> => ep93xx_dma_tasklet => tasklet_action => __do_softirq => irq_exit => __handle_domain_irq => vic_handle_irq => __irq_usr => 0xb66c6668 Just abort the transfers and warn if the HW state is not what we expect. Move draining into device_synchronize callback. Signed-off-by:
Alexander Sverdlin <alexander.sverdlin@gmail.com> Signed-off-by:
-
Alexander Sverdlin authored
commit 0037ae47 upstream. The current buffer is being reset to zero on device_free_chan_resources() but not on device_terminate_all(). It could happen that HW is restarted and expects BASE0 to be used, but the driver is not synchronized and will start from BASE1. One solution is to reset the buffer explicitly in m2p_hw_setup(). Signed-off-by:
-
Hiroyuki Yokoyama authored
commit 9a445bbb upstream. This patch fixes the register definition of AE (Address Error flag) bit. Fixes: 0c1c8ff3 ("dmaengine: usb-dmac: Add Renesas USB DMA Controller (USB-DMAC) driver") Signed-off-by:
Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com> [Shimoda: add Fixes and Cc tags in the commit log] Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
-
Marc Zyngier authored
commit ddf42d06 upstream. When an interrupt is injected with the HW bit set (indicating that deactivation should be propagated to the physical distributor), special care must be taken so that we never mark the corresponding LR with the Active+Pending state (as the pending state is kept in the physycal distributor). Cc: stable@vger.kernel.org Fixes: 140b086d ("KVM: arm/arm64: vgic-new: Add GICv2 world switch backend") Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Reviewed-by:
Christoffer Dall <cdall@linaro.org> Signed-off-by:
-
Marc Zyngier authored
commit 3d6e77ad upstream. When an interrupt is injected with the HW bit set (indicating that deactivation should be propagated to the physical distributor), special care must be taken so that we never mark the corresponding LR with the Active+Pending state (as the pending state is kept in the physycal distributor). Fixes: 59529f69 ("KVM: arm/arm64: vgic-new: Add GICv3 world switch backend") Signed-off-by:
-
Wanpeng Li authored
commit 9bc1f09f upstream. INFO: task gnome-terminal-:1734 blocked for more than 120 seconds. Not tainted 4.12.0-rc4+ #8 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. gnome-terminal- D 0 1734 1015 0x00000000 Call Trace: __schedule+0x3cd/0xb30 schedule+0x40/0x90 kvm_async_pf_task_wait+0x1cc/0x270 ? __vfs_read+0x37/0x150 ? prepare_to_swait+0x22/0x70 do_async_page_fault+0x77/0xb0 ? do_async_page_fault+0x77/0xb0 async_page_fault+0x28/0x30 This is triggered by running both win7 and win2016 on L1 KVM simultaneously, and then gives stress to memory on L1, I can observed this hang on L1 when at least ~70% swap area is occupied on L0. This is due to async pf was injected to L2 which should be injected to L1, L2 guest starts receiving pagefault w/ bogus %cr2(apf token from the host actually), and L1 guest starts accumulating tasks stuck in D state in kvm_async_pf_task_wait() since missing PAGE_READY async_pfs. This patch fixes the hang by doing async pf when executing L1 guest. Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Marc Zyngier authored
commit 33b5c388 upstream. We currently have the HSCTLR.A bit set, trapping unaligned accesses at HYP, but we're not really prepared to deal with it. Since the rest of the kernel is pretty happy about that, let's follow its example and set HSCTLR.A to zero. Modern CPUs don't really care. Signed-off-by:
-
Marc Zyngier authored
commit 78fd6dcf upstream. We currently have the SCTLR_EL2.A bit set, trapping unaligned accesses at EL2, but we're not really prepared to deal with it. So far, this has been unnoticed, until GCC 7 started emitting those (in particular 64bit writes on a 32bit boundary). Since the rest of the kernel is pretty happy about that, let's follow its example and set SCTLR_EL2.A to zero. Modern CPUs don't really care. Reported-by:
Alexander Graf <agraf@suse.de> Signed-off-by:
-
Marc Zyngier authored
commit d68c1f7f upstream. __do_hyp_init has the rather bad habit of ignoring RES1 bits and writing them back as zero. On a v8.0-8.2 CPU, this doesn't do anything bad, but may end-up being pretty nasty on future revisions of the architecture. Let's preserve those bits so that we don't have to fix this later on. Signed-off-by:
-
Wanpeng Li authored
commit a3641631 upstream. If "i" is the last element in the vcpu->arch.cpuid_entries[] array, it potentially can be exploited the vulnerability. this will out-of-bounds read and write. Luckily, the effect is small: /* when no next entry is found, the current entry[i] is reselected */ for (j = i + 1; ; j = (j + 1) % nent) { struct kvm_cpuid_entry2 *ej = &vcpu->arch.cpuid_entries[j]; if (ej->function == e->function) { It reads ej->maxphyaddr, which is user controlled. However... ej->flags |= KVM_CPUID_FLAG_STATE_READ_NEXT; After cpuid_entries there is int maxphyaddr; struct x86_emulate_ctxt emulate_ctxt; /* 16-byte aligned */ So we have: - cpuid_entries at offset 1B50 (6992) - maxphyaddr at offset 27D0 (6992 + 3200 = 10192) - padding at 27D4...27DF - emulate_ctxt at 27E0 And it writes in the padding. Pfew, writing the ops field of emulate_ctxt would have been much worse. This patch fixes it by modding the index to avoid the out-of-bounds access. Worst case, i == j and ej->function == e->function, the loop can bail out. Reported-by:
Moguofang <moguofang@huawei.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Guofang Mo <moguofang@huawei.com> Signed-off-by:
-
Paolo Bonzini authored
commit bbaf0e2b upstream. native_safe_halt enables interrupts, and you just shouldn't call rcu_irq_enter() with interrupts enabled. Reorder the call with the following local_irq_disable() to respect the invariant. Reported-by:
Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Tested-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Juergen Gross authored
commit 1ea34adb upstream. When booted as Xen dom0 there won't be an EFI memmap allocated. Avoid issuing an error message in this case: [ 0.144079] efi: Failed to allocate new EFI memmap Signed-off-by:
Matt Fleming <matt@codeblueprint.co.uk> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/20170526113652.21339-2-matt@codeblueprint.co.ukSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Trond Myklebust authored
commit b26b78cb upstream. If an NFSv4 client asks us for the supattr_exclcreat, then we must not return attributes that are unsupported by this minor version. Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Fixes: 75976de6 ("NFSD: Return word2 bitmask if setting security..,") Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
