- 20 Oct, 2021 3 commits
-
-
Guangbin Huang authored
Currently, DWRR of tc will be initialized to a fixed value when this tc is enabled, but it is not been reset to 0 when this tc is disabled. It cause a problem that the DWRR of unused tc is not 0 after using tc tool to add and delete multi-tc parameters. For examples, after enabling 4 TCs and restoring to 1 TC by follow tc commands: $ tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 1 2 3 queues \ 8@0 8@8 8@16 8@24 hw 1 mode channel $ tc qdisc del dev eth0 root Now there is just one TC is enabled for eth0, but the tc info querying by debugfs is shown as follow: $ cat /mnt/hns3/0000:7d:00.0/tm/tc_sch_info enabled tc number: 1 weight_offset: 14 TC MODE WEIGHT 0 dwrr 100 1 dwrr 100 2 dwrr 100 3 dwrr 100 4 dwrr 0 5 dwrr 0 6 dwrr 0 7 dwrr 0 This patch fixes it by resetting DWRR of tc to 0 when tc is disabled. Fixes: 84844054 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiaran Zhang authored
Add configuration of interrupt type and fifo interrupt enable of TM QCN error event if enabled, otherwise this event will not be reported when there is error. Fixes: d914971d ("net: hns3: remove redundant query in hclge_config_tm_hw_err_int()") Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eugene Crosser authored
This reverts commit 09e856d5. When an interface is enslaved in a VRF, prerouting conntrack hook is called twice: once in the context of the original input interface, and once in the context of the VRF interface. If no special precausions are taken, this leads to creation of two conntrack entries instead of one, and breaks SNAT. Commit above was intended to avoid creation of extra conntrack entries when input interface is enslaved in a VRF. It did so by resetting conntrack related data associated with the skb when it enters VRF context. However it breaks netfilter operation. Imagine a use case when conntrack zone must be assigned based on the original input interface, rather than VRF interface (that would make original interfaces indistinguishable). One could create netfilter rules similar to these: chain rawprerouting { type filter hook prerouting priority raw; iif realiface1 ct zone set 1 return iif realiface2 ct zone set 2 return } This works before the mentioned commit, but not after: zone assignment is "forgotten", and any subsequent NAT or filtering that is dependent on the conntrack zone does not work. Here is a reproducer script that demonstrates the difference in behaviour. ========== #!/bin/sh # This script demonstrates unexpected change of nftables behaviour # caused by commit 09e856d5 ""vrf: Reset skb conntrack # connection on VRF rcv" # https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=09e856d54bda5f288ef8437a90ab2b9b3eab83d1 # # Before the commit, it was possible to assign conntrack zone to a # packet (or mark it for `notracking`) in the prerouting chanin, raw # priority, based on the `iif` (interface from which the packet # arrived). # After the change, # if the interface is enslaved in a VRF, such # assignment is lost. Instead, assignment based on the `iif` matching # the VRF master interface is honored. Thus it is impossible to # distinguish packets based on the original interface. # # This script demonstrates this change of behaviour: conntrack zone 1 # or 2 is assigned depending on the match with the original interface # or the vrf master interface. It can be observed that conntrack entry # appears in different zone in the kernel versions before and after # the commit. IPIN=172.30.30.1 IPOUT=172.30.30.2 PFXL=30 ip li sh vein >/dev/null 2>&1 && ip li del vein ip li sh tvrf >/dev/null 2>&1 && ip li del tvrf nft list table testct >/dev/null 2>&1 && nft delete table testct ip li add vein type veth peer veout ip li add tvrf type vrf table 9876 ip li set veout master tvrf ip li set vein up ip li set veout up ip li set tvrf up /sbin/sysctl -w net.ipv4.conf.veout.accept_local=1 /sbin/sysctl -w net.ipv4.conf.veout.rp_filter=0 ip addr add $IPIN/$PFXL dev vein ip addr add $IPOUT/$PFXL dev veout nft -f - <<__END__ table testct { chain rawpre { type filter hook prerouting priority raw; iif { veout, tvrf } meta nftrace set 1 iif veout ct zone set 1 return iif tvrf ct zone set 2 return notrack } chain rawout { type filter hook output priority raw; notrack } } __END__ uname -rv conntrack -F ping -W 1 -c 1 -I vein $IPOUT conntrack -L Signed-off-by: Eugene Crosser <crosser@average.org> Acked-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 19 Oct, 2021 5 commits
-
-
Christophe JAILLET authored
If we return before the end of the 'for_each_child_of_node()' iterator, the reference taken on 'port' must be released. Add the missing 'of_node_put()' calls. Fixes: 83c0afae ("net: dsa: Add new binding implementation") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/15d5310d1d55ad51c1af80775865306d92432e03.1634587046.git.christophe.jaillet@wanadoo.frSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
David S. Miller authored
Merge tag 'linux-can-fixes-for-5.15-20211019' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2021-10-19 this is a pull request of a single patch for net/master. The patch is by me and fixes the error handling in case of a FC timeout in the TX path of the ISOTOP CAN protocol. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Zheyu Ma authored
During the process of driver probing, the probe function should return < 0 for failure, otherwise, the kernel will treat value > 0 as success. Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Zheyu Ma authored
During the process of driver probing, the probe function should return < 0 for failure, otherwise, the kernel will treat value > 0 as success. Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Marc Kleine-Budde authored
When the a large chunk of data send and the receiver does not send a Flow Control frame back in time, the sendmsg() does not return a error code, but the number of bytes sent corresponding to the size of the packet. If a timeout occurs the isotp_tx_timer_handler() is fired, sets sk->sk_err and calls the sk->sk_error_report() function. It was wrongly expected that the error would be propagated to user space in every case. For isotp_sendmsg() blocking on wait_event_interruptible() this is not the case. This patch fixes the problem by checking if sk->sk_err is set and returning the error to user space. Fixes: e057dd3f ("can: add ISO 15765-2:2016 transport protocol") Link: https://github.com/hartkopp/can-isotp/issues/42 Link: https://github.com/hartkopp/can-isotp/pull/43 Link: https://lore.kernel.org/all/20210507091839.1366379-1-mkl@pengutronix.de Cc: stable@vger.kernel.org Reported-by: Sottas Guillaume (LMB) <Guillaume.Sottas@liebherr.com> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
- 18 Oct, 2021 12 commits
-
-
Nathan Chancellor authored
A new warning in clang points out two places in this driver where boolean expressions are being used with a bitwise OR instead of a logical one: drivers/net/ethernet/netronome/nfp/nfp_asm.c:199:20: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical] reg->src_lmextn = swreg_lmextn(lreg) | swreg_lmextn(rreg); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ || drivers/net/ethernet/netronome/nfp/nfp_asm.c:199:20: note: cast one or both operands to int to silence this warning drivers/net/ethernet/netronome/nfp/nfp_asm.c:280:20: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical] reg->src_lmextn = swreg_lmextn(lreg) | swreg_lmextn(rreg); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ || drivers/net/ethernet/netronome/nfp/nfp_asm.c:280:20: note: cast one or both operands to int to silence this warning 2 errors generated. The motivation for the warning is that logical operations short circuit while bitwise operations do not. In this case, it does not seem like short circuiting is harmful so implement the suggested fix of changing to a logical operation to fix the warning. Link: https://github.com/ClangBuiltLinux/linux/issues/1479Reported-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20211018193101.2340261-1-nathan@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
Tianjia Zhang authored
Kernel TLS test has added SM4 GCM/CCM algorithm support, but SM4 algorithm is not compiled by default, this patch add SM4 config dependency. Reported-by: Hangbin Liu <liuhangbin@gmail.com> Reported-by: kernel test robot <oliver.sang@intel.com> Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jeremy Kerr authored
We currently have some implicit padding in struct sockaddr_mctp. This patch makes this padding explicit, and ensures we have consistent layout on platforms with <32bit alignmnent. Fixes: 60fc6398 ("mctp: Add sockaddr_mctp to uapi") Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jeremy Kerr authored
Use the more precise __kernel_sa_family_t for smctp_family, to match struct sockaddr. Also, use an unsigned int for the network member; negative networks don't make much sense. We're already using unsigned for mctp_dev and mctp_skb_cb, but need to change mctp_sock to suit. Fixes: 60fc6398 ("mctp: Add sockaddr_mctp to uapi") Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Acked-by: Eugene Syromiatnikov <esyr@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Zheyu Ma authored
During the process of driver probing, the probe function should return < 0 for failure, otherwise, the kernel will treat value > 0 as success. Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Wan Jiabing authored
Fix following coccicheck warning: ./drivers/net/ethernet/mscc/ocelot_vsc7514.c:946:1-33: WARNING: Function for_each_available_child_of_node should have of_node_put() before goto. Early exits from for_each_available_child_of_node should decrement the node reference counter. Signed-off-by: Wan Jiabing <wanjiabing@vivo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Wan Jiabing authored
Fix following coccicheck warning: ./drivers/net/ethernet/microchip/sparx5/s4parx5_main.c:723:1-33: WARNING: Function for_each_available_child_of_node should have of_node_put() before goto Early exits from for_each_available_child_of_node should decrement the node reference counter. Signed-off-by: Wan Jiabing <wanjiabing@vivo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Paul Blakey authored
First fragmented packets (frag offset = 0) byte len is zeroed when stolen by ip_defrag(). And since act_ct update the stats only afterwards (at end of execute), bytes aren't correctly accounted for such packets. To fix this, move stats update to start of action execute. Fixes: b57dc7c1 ("net/sched: Introduce action ct") Signed-off-by: Paul Blakey <paulb@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
DENG Qingfang authored
Setting ds->num_ports to DSA_MAX_PORTS made DSA core allocate unnecessary dsa_port's and call mt7530_port_disable for non-existent ports. Set it to MT7530_NUM_PORTS to fix that, and dsa_is_user_port check in port_enable/disable is no longer required. Cc: stable@vger.kernel.org Signed-off-by: DENG Qingfang <dqfext@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Aleksander Jan Bajkowski authored
I compared the register definitions with the D-Link DWR-966 GPL sources and found that the PUAFD field definition was incorrect. This definition is unused and causes no issues. Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200") Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge tag 'linux-can-fixes-for-5.15-20211017' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2021-10-17 this is a pull request of 11 patches for net/master. The first 4 patches are by Ziyang Xuan and Zhang Changzhong and fix 1 use after free and 3 standard conformance problems in the j1939 CAN stack. The next 2 patches are by Ziyang Xuan and fix 2 concurrency problems in the ISOTP CAN stack. Yoshihiro Shimoda's patch for the rcar_can fix suspend/resume on not running CAN interfaces. Aswath Govindraju's patch for the m_can driver fixes access for MMIO devices. Zheyu Ma contributes a patch for the peak_pci driver to fix a use after free. Stephane Grosjean's 2 patches fix CAN error state handling in the peak_usb driver. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Randy Dunlap authored
On i386, the baycom_epp driver wants to inspect X86 CPU features (TSC) and then act on that data, but that info is not available when running on UML, so prevent that test and do the default action. Prevents this build error on UML + i386: ../drivers/net/hamradio/baycom_epp.c: In function ‘epp_bh’: ../drivers/net/hamradio/baycom_epp.c:630:6: error: implicit declaration of function ‘boot_cpu_has’; did you mean ‘get_cpu_mask’? [-Werror=implicit-function-declaration] if (boot_cpu_has(X86_FEATURE_TSC)) \ ^ ../drivers/net/hamradio/baycom_epp.c:658:2: note: in expansion of macro ‘GETTICK’ GETTICK(time1); Fixes: 68f5d3f3 ("um: add PCI over virtio emulation driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: linux-um@lists.infradead.org Cc: Jeff Dike <jdike@addtoit.com> Cc: Richard Weinberger <richard@nod.at> Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Thomas Sailer <t.sailer@alumni.ethz.ch> Cc: linux-hams@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 17 Oct, 2021 11 commits
-
-
Stephane Grosjean authored
Since alloc_can_err_skb() puts NULL in cf in the case when skb cannot be allocated and can_change_state() handles the case when cf is NULL, the test on the nullity of skb is now unnecessary. Link: https://lore.kernel.org/all/20210929142111.55757-2-s.grosjean@peak-system.comSigned-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Stephane Grosjean authored
This corrects the lack of notification of a return to ERROR_ACTIVE state for USB - CANFD devices from PEAK-System. Fixes: 0a25e1f4 ("can: peak_usb: add support for PEAK new CANFD USB adapters") Link: https://lore.kernel.org/all/20210929142111.55757-1-s.grosjean@peak-system.com Cc: stable@vger.kernel.org Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Zheyu Ma authored
When remove the module peek_pci, referencing 'chan' again after releasing 'dev' will cause UAF. Fix this by releasing 'dev' later. The following log reveals it: [ 35.961814 ] BUG: KASAN: use-after-free in peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.963414 ] Read of size 8 at addr ffff888136998ee8 by task modprobe/5537 [ 35.965513 ] Call Trace: [ 35.965718 ] dump_stack_lvl+0xa8/0xd1 [ 35.966028 ] print_address_description+0x87/0x3b0 [ 35.966420 ] kasan_report+0x172/0x1c0 [ 35.966725 ] ? peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.967137 ] ? trace_irq_enable_rcuidle+0x10/0x170 [ 35.967529 ] ? peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.967945 ] __asan_report_load8_noabort+0x14/0x20 [ 35.968346 ] peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.968752 ] pci_device_remove+0xa9/0x250 Fixes: e6d9c80b ("can: peak_pci: add support of some new PEAK-System PCI cards") Link: https://lore.kernel.org/all/1634192913-15639-1-git-send-email-zheyuma97@gmail.com Cc: stable@vger.kernel.org Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Aswath Govindraju authored
The read and writes from the fifo are from a buffer, with various fields and data at predefined offsets. So, they should not be done to the same address(or port) in case of val_count greater than 1. Therefore, fix this by using iowrite32()/ioread32() instead of ioread32_rep()/iowrite32_rep(). Also, the write into FIFO must be performed with an offset from the message ram base address. Therefore, fix the base address to mram_base. Fixes: e3938177 ("can: m_can: Disable IRQs on FIFO bus errors") Link: https://lore.kernel.org/all/20210920123344.2320-1-a-govindraju@ti.comSigned-off-by: Aswath Govindraju <a-govindraju@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Yoshihiro Shimoda authored
If the driver was not opened, rcar_can_suspend() should not call clk_disable() because the clock was not enabled. Fixes: fd115931 ("can: add Renesas R-Car CAN driver") Link: https://lore.kernel.org/all/20210924075556.223685-1-yoshihiro.shimoda.uh@renesas.com Cc: stable@vger.kernel.org Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by: Ayumi Nakamichi <ayumi.nakamichi.kf@renesas.com> Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu> Tested-by: Biju Das <biju.das.jz@bp.renesas.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Ziyang Xuan authored
When isotp_sendmsg() concurrent, tx.state of all TX processes can be ISOTP_IDLE. The conditions so->tx.state != ISOTP_IDLE and wq_has_sleeper(&so->wait) can not protect TX buffer from being accessed by multiple TX processes. We can use cmpxchg() to try to modify tx.state to ISOTP_SENDING firstly. If the modification of the previous process succeed, the later process must wait tx.state to ISOTP_IDLE firstly. Thus, we can ensure TX buffer is accessed by only one process at the same time. And we should also restore the original tx.state at the subsequent error processes. Fixes: e057dd3f ("can: add ISO 15765-2:2016 transport protocol") Link: https://lore.kernel.org/all/c2517874fbdf4188585cf9ddf67a8fa74d5dbde5.1633764159.git.william.xuanziyang@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Ziyang Xuan authored
Using wait_event_interruptible() to wait for complete transmission, but do not check the result of wait_event_interruptible() which can be interrupted. It will result in TX buffer has multiple accessors and the later process interferes with the previous process. Following is one of the problems reported by syzbot. ============================================================= WARNING: CPU: 0 PID: 0 at net/can/isotp.c:840 isotp_tx_timer_handler+0x2e0/0x4c0 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.13.0-rc7+ #68 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014 RIP: 0010:isotp_tx_timer_handler+0x2e0/0x4c0 Call Trace: <IRQ> ? isotp_setsockopt+0x390/0x390 __hrtimer_run_queues+0xb8/0x610 hrtimer_run_softirq+0x91/0xd0 ? rcu_read_lock_sched_held+0x4d/0x80 __do_softirq+0xe8/0x553 irq_exit_rcu+0xf8/0x100 sysvec_apic_timer_interrupt+0x9e/0xc0 </IRQ> asm_sysvec_apic_timer_interrupt+0x12/0x20 Add result check for wait_event_interruptible() in isotp_sendmsg() to avoid multiple accessers for tx buffer. Fixes: e057dd3f ("can: add ISO 15765-2:2016 transport protocol") Link: https://lore.kernel.org/all/10ca695732c9dd267c76a3c30f37aefe1ff7e32f.1633764159.git.william.xuanziyang@huawei.com Cc: stable@vger.kernel.org Reported-by: syzbot+78bab6958a614b0c80b9@syzkaller.appspotmail.com Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Zhang Changzhong authored
The receiver should abort TP if 'total message size' in TP.CM_RTS and TP.CM_BAM is less than 9 or greater than 1785 [1], but currently the j1939 stack only checks the upper bound and the receiver will accept the following broadcast message: vcan1 18ECFF00 [8] 20 08 00 02 FF 00 23 01 vcan1 18EBFF00 [8] 01 00 00 00 00 00 00 00 vcan1 18EBFF00 [8] 02 00 FF FF FF FF FF FF This patch adds check for the lower bound and abort illegal TP. [1] SAE-J1939-82 A.3.4 Row 2 and A.3.6 Row 6. Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/all/1634203601-3460-1-git-send-email-zhangchangzhong@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Zhang Changzhong authored
According to SAE-J1939-21, the data length of TP.DT must be 8 bytes, so cancel session when receive unexpected TP.DT message. Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/all/1632972800-45091-1-git-send-email-zhangchangzhong@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Ziyang Xuan authored
It will trigger UAF for rx_kref of j1939_priv as following. cpu0 cpu1 j1939_sk_bind(socket0, ndev0, ...) j1939_netdev_start j1939_sk_bind(socket1, ndev0, ...) j1939_netdev_start j1939_priv_set j1939_priv_get_by_ndev_locked j1939_jsk_add ..... j1939_netdev_stop kref_put_lock(&priv->rx_kref, ...) kref_get(&priv->rx_kref, ...) REFCOUNT_WARN("addition on 0;...") ==================================================== refcount_t: addition on 0; use-after-free. WARNING: CPU: 1 PID: 20874 at lib/refcount.c:25 refcount_warn_saturate+0x169/0x1e0 RIP: 0010:refcount_warn_saturate+0x169/0x1e0 Call Trace: j1939_netdev_start+0x68b/0x920 j1939_sk_bind+0x426/0xeb0 ? security_socket_bind+0x83/0xb0 The rx_kref's kref_get() and kref_put() should use j1939_netdev_lock to protect. Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/all/20210926104757.2021540-1-william.xuanziyang@huawei.com Cc: stable@vger.kernel.org Reported-by: syzbot+85d9878b19c94f9019ad@syzkaller.appspotmail.com Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
Ziyang Xuan authored
When the session state is J1939_SESSION_DONE, j1939_tp_rxtimer() will give an alert "rx timeout, send abort", but do nothing actually. Move the alert into session active judgment condition, it is more reasonable. One of the scenarios is that j1939_tp_rxtimer() execute followed by j1939_xtp_rx_abort_one(). After j1939_xtp_rx_abort_one(), the session state is J1939_SESSION_DONE, then j1939_tp_rxtimer() give an alert. Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/all/20210906094219.95924-1-william.xuanziyang@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-
- 16 Oct, 2021 3 commits
-
-
Nikolay Aleksandrov authored
When I added IGMPv3 support I decided to follow the RFC for computing the GMI dynamically: " 8.4. Group Membership Interval The Group Membership Interval is the amount of time that must pass before a multicast router decides there are no more members of a group or a particular source on a network. This value MUST be ((the Robustness Variable) times (the Query Interval)) plus (one Query Response Interval)." But that actually is inconsistent with how the bridge used to compute it for IGMPv2, where it was user-configurable that has a correct default value but it is up to user-space to maintain it. This would make it consistent with the other timer values which are also maintained correct by the user instead of being dynamically computed. It also changes back to the previous user-expected GMI behaviour for IGMPv3 queries which were supported before IGMPv3 was added. Note that to properly compute it dynamically we would need to add support for "Robustness Variable" which is currently missing. Reported-by: Hangbin Liu <liuhangbin@gmail.com> Fixes: 0436862e ("net: bridge: mcast: support for IGMPv3/MLDv2 ALLOW_NEW_SOURCES report") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Stefano Garzarella authored
In `test_no_sockets` we don't expect any sockets, indeed check_no_sockets() prints an error and exits if `sockets` list is not empty, so free_sock_stat() call is unnecessary since it would only be called when the `sockets` list is empty. This was discovered by a strange warning printed by gcc v11.2.1: In file included from ../../include/linux/list.h:7, from vsock_diag_test.c:18: vsock_diag_test.c: In function ‘test_no_sockets’: ../../include/linux/kernel.h:35:45: error: array subscript ‘struct vsock_stat[0]’ is partly outside array bound s of ‘struct list_head[1]’ [-Werror=array-bounds] 35 | const typeof(((type *)0)->member) * __mptr = (ptr); \ | ^~~~~~ ../../include/linux/list.h:352:9: note: in expansion of macro ‘container_of’ 352 | container_of(ptr, type, member) | ^~~~~~~~~~~~ ../../include/linux/list.h:393:9: note: in expansion of macro ‘list_entry’ 393 | list_entry((pos)->member.next, typeof(*(pos)), member) | ^~~~~~~~~~ ../../include/linux/list.h:522:21: note: in expansion of macro ‘list_next_entry’ 522 | n = list_next_entry(pos, member); \ | ^~~~~~~~~~~~~~~ vsock_diag_test.c:325:9: note: in expansion of macro ‘list_for_each_entry_safe’ 325 | list_for_each_entry_safe(st, next, sockets, list) { | ^~~~~~~~~~~~~~~~~~~~~~~~ In file included from vsock_diag_test.c:18: vsock_diag_test.c:333:19: note: while referencing ‘sockets’ 333 | LIST_HEAD(sockets); | ^~~~~~~ ../../include/linux/list.h:23:26: note: in definition of macro ‘LIST_HEAD’ 23 | struct list_head name = LIST_HEAD_INIT(name) It seems related to some compiler optimization and assumption about the empty `sockets` list, since this warning is printed only with -02 or -O3. Also removing `exit(1)` from check_no_sockets() makes the warning disappear since in that case free_sock_stat() can be reached also when the list is not empty. Reported-by: Marc-André Lureau <marcandre.lureau@redhat.com> Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Link: https://lore.kernel.org/r/20211014152045.173872-1-sgarzare@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queueJakub Kicinski authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2021-10-14 Brett ensures RDMA nodes are removed during release and rebuild. He also corrects fw.mgmt.api to include the patch number for proper identification. Dave stops ida_free() being called when an IDA has not been allocated. Michal corrects the order of parameters being provided and the number of entries skipped for UDP tunnels. ==================== Link: https://lore.kernel.org/r/20211014181953.3538330-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
- 15 Oct, 2021 6 commits
-
-
Stephen Suryaputra authored
Commit bdb7cc64 ("ipv6: Count interface receive statistics on the ingress netdev") does not work when ip6_forward() executes on the skbs with vrf-enslaved netdev. Use IP6CB(skb)->iif to get to the right one. Add a selftest script to verify. Fixes: bdb7cc64 ("ipv6: Count interface receive statistics on the ingress netdev") Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20211014130845.410602-1-ssuryaextr@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>
-
David S. Miller authored
Leonard Crestez says: ==================== tcp: md5: Fix overlap between vrf and non-vrf keys With net.ipv4.tcp_l3mdev_accept=1 it is possible for a listen socket to accept connection from the same client address in different VRFs. It is also possible to set different MD5 keys for these clients which differ only in the tcpm_l3index field. This appears to work when distinguishing between different VRFs but not between non-VRF and VRF connections. In particular: * tcp_md5_do_lookup_exact will match a non-vrf key against a vrf key. This means that adding a key with l3index != 0 after a key with l3index == 0 will cause the earlier key to be deleted. Both keys can be present if the non-vrf key is added later. * _tcp_md5_do_lookup can match a non-vrf key before a vrf key. This casues failures if the passwords differ. This can be fixed by making tcp_md5_do_lookup_exact perform an actual exact comparison on l3index and by making __tcp_md5_do_lookup perfer vrf-bound keys above other considerations like prefixlen. The fact that keys with l3index==0 affect VRF connections is usually not desirable, VRFs are meant to be completely independent. This behavior needs to preserved for backwards compatibility. Also, applications can just bind listen sockets to VRF and never specify TCP_MD5SIG_FLAG_IFINDEX at all. So far the combination of TCP_MD5SIG_FLAG_IFINDEX with tcpm_ifindex == 0 was an error, accept this to mean "key only applies to default VRF". This is what applications using VRFs for traffic separation want. This also contains tests for the second part. It does not contain tests for overlapping keys, that would require more changes in nettest to add multiple keys. These scenarios are also covered by my tests for TCP-AO, especially around this area: https://github.com/cdleonard/tcp-authopt-test/blob/main/tcp_authopt_test/test_vrf_bind.py Changes since V2: * Rename --do-bind-key-ifindex to --force-bind-key-ifindex * Fix referencing TCP_MD5SIG_FLAG_IFINDEX as TCP_MD5SIG_IFINDEX Link to v2: https://lore.kernel.org/netdev/cover.1634107317.git.cdleonard@gmail.com/ Changes since V1: * Accept (TCP_MD5SIG_IFINDEX with tcpm_ifindex == 0) * Add flags for explicitly including or excluding TCP_MD5SIG_FLAG_IFINDEX to nettest * Add few more tests in fcnal-test.sh. Link to v1: https://lore.kernel.org/netdev/3d8387d499f053dba5cd9184c0f7b8445c4470c6.1633542093.git.cdleonard@gmail.com/ ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Leonard Crestez authored
Test that applications binding listening sockets to VRFs without specifying TCP_MD5SIG_FLAG_IFINDEX will work as expected. This would be broken if __tcp_md5_do_lookup always made a strict comparison on l3index. See this email: https://lore.kernel.org/netdev/209548b5-27d2-2059-f2e9-2148f5a0291b@gmail.com/ Applications using tcp_l3mdev_accept=1 and a single global socket (not bound to any interface) also should have a way to specify keys that are only for the default VRF, this is done by --force-bind-key-ifindex without otherwise binding to a device. Signed-off-by: Leonard Crestez <cdleonard@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Leonard Crestez authored
These options allow explicit control over the TCP_MD5SIG_FLAG_IFINDEX flag instead of always setting it based on binding to an interface. Do this by converting to getopt_long because nettest has too many single-character flags already and getopt_long is widely used in selftests. Signed-off-by: Leonard Crestez <cdleonard@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Leonard Crestez authored
Multiple VRFs are generally meant to be "separate" but right now md5 keys for the default VRF also affect connections inside VRFs if the IP addresses happen to overlap. So far the combination of TCP_MD5SIG_FLAG_IFINDEX with tcpm_ifindex == 0 was an error, accept this to mean "key only applies to default VRF". This is what applications using VRFs for traffic separation want. Signed-off-by: Leonard Crestez <cdleonard@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Leonard Crestez authored
With net.ipv4.tcp_l3mdev_accept=1 it is possible for a listen socket to accept connection from the same client address in different VRFs. It is also possible to set different MD5 keys for these clients which differ only in the tcpm_l3index field. This appears to work when distinguishing between different VRFs but not between non-VRF and VRF connections. In particular: * tcp_md5_do_lookup_exact will match a non-vrf key against a vrf key. This means that adding a key with l3index != 0 after a key with l3index == 0 will cause the earlier key to be deleted. Both keys can be present if the non-vrf key is added later. * _tcp_md5_do_lookup can match a non-vrf key before a vrf key. This casues failures if the passwords differ. Fix this by making tcp_md5_do_lookup_exact perform an actual exact comparison on l3index and by making __tcp_md5_do_lookup perfer vrf-bound keys above other considerations like prefixlen. Fixes: dea53bb8 ("tcp: Add l3index to tcp_md5sig_key and md5 functions") Signed-off-by: Leonard Crestez <cdleonard@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-