- 06 Mar, 2013 32 commits
-
-
Dave Airlie authored
commit ae128786 upstream. If grub2 loads efifb/vesafb, then when systemd starts it can set the console font on that framebuffer device, however when we then load the native KMS driver, the first thing it does is tear down the generic framebuffer driver. The thing is the generic code is doing the right thing, it frees the font because otherwise it would leak memory. However we can assume that if you are removing the generic firmware driver (vesa/efi/offb), that a new driver *should* be loading soon after, so we effectively leak the font. However the old code left a dangling pointer in vc->vc_font.data and we can now reuse that dangling pointer to load the font into the new driver, now that we aren't freeing it. Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=892340 Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Dave Airlie authored
commit 2a248307 upstream. When we switch from 256->512 byte font rendering mode, it means the current contents of the screen is being reinterpreted. The bit that holds the high bit of the 9-bit font, may have been previously set, and thus the new font misrenders. The problem case we see is grub2 writes spaces with the bit set, so it ends up with data like 0x820, which gets reinterpreted into 0x120 char which the font translates into G with a circumflex. This flashes up on screen at boot and is quite ugly. A current side effect of this patch though is that any rendering on the screen changes color to a slightly darker color, but at least the screen no longer corrupts. v2: as suggested by hpa, always clear the attribute space, whether we are are going to or from 512 chars. Signed-off-by:
-
Joseph Salisbury authored
commit 66f2fda9 upstream. This patch adds a quirk to allow the Sony VGN-FW41E_H to suspend/resume properly. References: http://bugs.launchpad.net/bugs/1113547Signed-off-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Ian Abbott authored
commit cc400e18 upstream. Some low-level comedi drivers (incorrectly) point `dev->read_subdev` or `dev->write_subdev` to a subdevice that does not support asynchronous commands. Comedi's poll(), read() and write() file operation handlers assume these subdevices do support asynchronous commands. In particular, they assume `s->async` is valid (where `s` points to the read or write subdevice), which it won't be if it has been set incorrectly. This can lead to a NULL pointer dereference. Check `s->async` is non-NULL in `comedi_poll()`, `comedi_read()` and `comedi_write()` to avoid the bug. Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
-
majianpeng authored
commit 2d32b29a upstream. When free nfs-client, it must free the ->cl_stateids. Signed-off-by:
Jianpeng Ma <majianpeng@gmail.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Leonid Shatz authored
commit b22affe0 upstream. hrtimer_enqueue_reprogram contains a race which could result in timer.base switch during unlock/lock sequence. hrtimer_enqueue_reprogram is releasing the lock protecting the timer base for calling raise_softirq_irqsoff() due to a lock ordering issue versus rq->lock. If during that time another CPU calls __hrtimer_start_range_ns() on the same hrtimer, the timer base might switch, before the current CPU can lock base->lock again and therefor the unlock_timer_base() call will unlock the wrong lock. [ tglx: Added comment and massaged changelog ] Signed-off-by:
Leonid Shatz <leonid.shatz@ravellosystems.com> Signed-off-by:
Izik Eidus <izik.eidus@ravellosystems.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Link: http://lkml.kernel.org/r/1359981217-389-1-git-send-email-izik.eidus@ravellosystems.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Oleg Nesterov authored
commit 183d95cd upstream. See https://bugzilla.redhat.com/show_bug.cgi?id=904907 read command causes bash to abort with double free or corruption (out). A simple test-case from Roman: // Compile the reproducer and send sigchld ti that process. // EINTR occurs even if SA_RESTART flag is set. void handler(int sig) { } main() { struct sigaction act; act.sa_handler = handler; act.sa_flags = SA_RESTART; sigaction (SIGCHLD, &act, 0); struct termio ttp; ioctl(0, TCGETA, &ttp); while(1) { if (ioctl(0, TCSETAW, ttp) < 0) { if (errno == EINTR) { fprintf(stderr, "BUG!"); return(1); } } } } Change set_termios/set_termiox to return -ERESTARTSYS to fix this particular problem. I didn't dare to change other EINTR's in drivers/tty/, but they look equally wrong. Reported-by:
Roman Rakus <rrakus@redhat.com> Reported-by:
Lingzhu Xiang <lxiang@redhat.com> Signed-off-by:
Oleg Nesterov <oleg@redhat.com> Cc: Jiri Slaby <jslaby@suse.cz> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Adam Thomas authored
commit 8afd500c upstream. The last orphan in the dnext list has its dnext set to NULL. Because of that, ubifs_delete_orphan assumes that it is not on the dnext list and frees it immediately instead ignoring it as a second delete. The orphan is later freed again by erase_deleted. This change adds an explicit flag to ubifs_orphan indicating whether it is pending delete. Signed-off-by:
Adam Thomas <adamthomas1111@gmail.com> Signed-off-by:
Artem Bityutskiy <artem.bityutskiy@linux.intel.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Takashi Iwai authored
commit edac8943 upstream. snd-aloop driver has no proper PM implementation, thus the PM resume may trigger Oops due to leftover timer instance. This patch adds the missing suspend/resume implementation. Reported-and-tested-by:
El boulangero <elboulangero@gmail.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Bjorn Helgaas authored
commit 4fa3e78b upstream. A bus_type has a list of devices (klist_devices), but the list and the subsys_private structure that contains it are not initialized until the bus_type is registered with bus_register(). The panic/reboot path has fixups that look up devices in pci_bus_type. If we panic before registering pci_bus_type, the bus_type exists but the list does not, so mach_reboot_fixups() trips over a null pointer and panics again: mach_reboot_fixups pci_get_device .. bus_find_device(&pci_bus_type, ...) bus->p is NULL Joonsoo reported a problem when panicking before PCI was initialized. I think this patch should be sufficient to replace the patch he posted here: https://lkml.org/lkml/2012/12/28/75 ("[PATCH] x86, reboot: skip reboot_fixups in early boot phase") Reported-by:
Joonsoo Kim <js1304@gmail.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Minchan Kim authored
commit 7e5a5104 upstream. Now zram allocates new page with GFP_KERNEL in zram I/O path if IO is partial. Unfortunately, It may cause deadlock with reclaim path like below. write_page from fs fs_lock allocation(GFP_KERNEL) reclaim pageout write_page from fs fs_lock <-- deadlock This patch fixes it by using GFP_NOIO. In read path, we reorganize code flow so that kmap_atomic is called after the GFP_NOIO allocation. Acked-by:
Jerome Marchand <jmarchand@redhat.com> Acked-by:
Nitin Gupta <ngupta@vflare.org> [ penberg@kernel.org: don't use GFP_ATOMIC ] Signed-off-by:
Pekka Enberg <penberg@kernel.org> Signed-off-by:
Minchan Kim <minchan@kernel.org> Signed-off-by:
-
Niu Yawei authored
commit f1167009 upstream. In ext4_mb_add_n_trim(), lg_prealloc_lock should be taken when changing the lg_prealloc_list. Signed-off-by:
Niu Yawei <yawei.niu@intel.com> Signed-off-by:
"Theodore Ts'o" <tytso@mit.edu> Signed-off-by:
-
Takashi Iwai authored
commit 2ad779b7 upstream. If the driver detects and invalid ELD, it gives an open error. But it forgot to release the assigned pin, converter and spdif ctls before returning. Signed-off-by:
-
Dave Hansen authored
commit f03574f2 upstream. This code was an optimization for 32-bit NUMA systems. It has probably been the cause of a number of subtle bugs over the years, although the conditions to excite them would have been hard to trigger. Essentially, we remap part of the kernel linear mapping area, and then sometimes part of that area gets freed back in to the bootmem allocator. If those pages get used by kernel data structures (say mem_map[] or a dentry), there's no big deal. But, if anyone ever tried to use the linear mapping for these pages _and_ cared about their physical address, bad things happen. For instance, say you passed __GFP_ZERO to the page allocator and then happened to get handed one of these pages, it zero the remapped page, but it would make a pte to the _old_ page. There are probably a hundred other ways that it could screw with things. We don't need to hang on to performance optimizations for these old boxes any more. All my 32-bit NUMA systems are long dead and buried, and I probably had access to more than most people. This code is causing real things to break today: https://lkml.org/lkml/2013/1/9/376 I looked in to actually fixing this, but it requires surgery to way too much brittle code, as well as stuff like per_cpu_ptr_to_phys(). [ hpa: Cc: this for -stable, since it is a memory corruption issue. However, an alternative is to simply mark NUMA as depends BROKEN rather than EXPERIMENTAL in the X86_32 subclause... ] Link: http://lkml.kernel.org/r/20130131005616.1C79F411@kernel.stglabs.ibm.comSigned-off-by:
H. Peter Anvin <hpa@linux.intel.com> [bwh: For 3.2, using the suggested alternative] Signed-off-by:
-
Clemens Ladisch authored
commit 7da58046 upstream. The quirk for the Roland/Cakewalk A-PRO keyboards accidentally used the wrong interface number, which prevented the driver from attaching to the device. Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
-
Ian Abbott authored
commit 754ab5c0 upstream. Comedi has two sorts of minor devices: (a) normal board minor devices in the range 0 to COMEDI_NUM_BOARD_MINORS-1 inclusive; and (b) special subdevice minor devices in the range COMEDI_NUM_BOARD_MINORS upwards that are used to open the same underlying comedi device as the normal board minor devices, but with non-default read and write subdevices for asynchronous commands. The special subdevice minor devices get created when a board supporting asynchronous commands is attached to a normal board minor device, and destroyed when the board is detached from the normal board minor device. One way to attach or detach a board is by using the COMEDI_DEVCONFIG ioctl. This should only be used on normal board minors as the special subdevice minors are too ephemeral. In particular, the change introduced in commit 7d3135af ("staging: comedi: prevent auto-unconfig of manually configured devices") breaks horribly for special subdevice minor devices. Since there's no legitimate use for the COMEDI_DEVCONFIG ioctl on a special subdevice minor device node, disallow it and return -ENOTTY. Signed-off-by:
-
Christian Borntraeger authored
commit 15bc8d84 upstream. On store status we need to copy the current state of registers into a save area. Currently we might save stale versions: The sie state descriptor doesnt have fields for guest ACRS,FPRS, those registers are simply stored in the host registers. The host program must copy these away if needed. We do that in vcpu_put/load. If we now do a store status in KVM code between vcpu_put/load, the saved values are not up-to-date. Lets collect the ACRS/FPRS before saving them. This also fixes some strange problems with hotplug and virtio-ccw, since the low level machine check handler (on hotplug a machine check will happen) will revalidate all registers with the content of the save area. Signed-off-by:
Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by:
Gleb Natapov <gleb@redhat.com> [bwh: Backported to 3.2 as done in 3.0 by Jiri Slaby] Signed-off-by:
-
Jan Kara authored
commit 091e26df upstream. Running AIO is pinning inode in memory using file reference. Once AIO is completed using aio_complete(), file reference is put and inode can be freed from memory. So we have to be sure that calling aio_complete() is the last thing we do with the inode. Reviewed-by:
Carlos Maiolino <cmaiolino@redhat.com> Acked-by:
Jeff Moyer <jmoyer@redhat.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Theodore Ts'o authored
commit c3ad83d9 upstream. Otherwise, ext4 file systems with the quota featured enable will get a very confusing "No such process" error message if the quota code is built as a module and the quota_v2 module has not been loaded. Signed-off-by:
-
Bjørn Mork authored
commit f8f0302b upstream. Adding three currently unsupported modems based on information from .inf driver files: Diag VID_1BBB&PID_0052&MI_00 AGPS VID_1BBB&PID_0052&MI_01 VOICE VID_1BBB&PID_0052&MI_02 AT VID_1BBB&PID_0052&MI_03 Modem VID_1BBB&PID_0052&MI_05 wwan VID_1BBB&PID_0052&MI_06 Diag VID_1BBB&PID_00B6&MI_00 AT VID_1BBB&PID_00B6&MI_01 Modem VID_1BBB&PID_00B6&MI_02 wwan VID_1BBB&PID_00B6&MI_03 Diag VID_1BBB&PID_00B7&MI_00 AGPS VID_1BBB&PID_00B7&MI_01 VOICE VID_1BBB&PID_00B7&MI_02 AT VID_1BBB&PID_00B7&MI_03 Modem VID_1BBB&PID_00B7&MI_04 wwan VID_1BBB&PID_00B7&MI_05 Updating the blacklist info for the X060S_X200 and X220_X500D, reserving interfaces for a wwan driver, based on wwan VID_1BBB&PID_0000&MI_04 wwan VID_1BBB&PID_0017&MI_06 Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Igor Grinberg authored
commit d107a204 upstream. The Chip Select Configuration Register must be programmed to 0x2 in order to achieve the correct behavior of the Static Memory Controller. Without this patch devices wired to DFI and accessed through SMC cannot be accessed after resume from S2. Do not rely on the boot loader to program the CSMSADRCFG register by programming it in the kernel smemc module. Signed-off-by:
Igor Grinberg <grinberg@compulab.co.il> Acked-by:
Eric Miao <eric.y.miao@gmail.com> Signed-off-by:
Haojian Zhuang <haojian.zhuang@gmail.com> Signed-off-by:
-
John David Anglin authored
commit 7139bc15 upstream. This patch goes a long way toward fixing the minifail bug, and it significantly improves the stability of SMP machines such as the rp3440. When write protecting a page for COW, we need to purge the existing translation. Otherwise, the COW break doesn't occur as expected because the TLB may still have a stale entry which allows writes. [jejb: fix up checkpatch errors] Signed-off-by:
John David Anglin <dave.anglin@bell.net> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Jean Delvare authored
commit 811af972 upstream. It doesn't seem this spinlock was properly initialized. This bug was introduced by commit 7a410e8d. Signed-off-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
Theodore Ts'o authored
commit 860d21e2 upstream. The only reason for sb_getblk() failing is if it can't allocate the buffer_head. So ENOMEM is more appropriate than EIO. In addition, make sure that the file system is marked as being inconsistent if sb_getblk() fails. Signed-off-by:
-
Thadeu Lima de Souza Cascardo authored
commit 6a040ce7 upstream. The DDW code uses a eeh_dev struct from the pci_dev. However, this is not set until eeh_add_device_late is called. Since pci_bus_add_devices is called before eeh_add_device_late, the PCI devices are added to the bus, making drivers' probe hooks to be called. These will call set_dma_mask, which will call the DDW code, which will require the eeh_dev struct from pci_dev. This would result in a crash, due to a NULL dereference. Calling eeh_add_device_late after pci_bus_add_devices would make the system BUG, because device files shouldn't be added to devices there were not added to the system. So, a new function is needed to add such files only after pci_bus_add_devices have been called. Signed-off-by:
Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Acked-by:
Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Maciej Sosnowski authored
commit c419fcfd upstream. When providers get blocked unregister_dca_providers() is called ending up with dca_providers and dca_domain lists emptied. Dca should be prevented from trying to unregister any provider if dca_domain list is found empty. Reported-by:
Jiang Liu <jiang.liu@huawei.com> Tested-by:
Gaohuai Han <hangaohuai@huawei.com> Signed-off-by:
Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by:
Dan Williams <djbw@fb.com> Signed-off-by:
-
Al Viro authored
commit 55ee64b3 upstream. Walking rbtree while it's modified is a Bad Idea(tm); besides, the result of find_vma() can be freed just as it's getting returned to caller. Fortunately, it's easy to fix - just take ->mmap_sem a bit earlier (and don't bother with find_vma() at all if virtp >= PAGE_OFFSET - in that case we don't even look at its result). While we are at it, what prevents VIDIOC_PREPARE_BUF calling v4l_prepare_buf() -> (e.g) vb2_ioctl_prepare_buf() -> vb2_prepare_buf() -> __buf_prepare() -> __qbuf_userptr() -> vb2_vmalloc_get_userptr() -> find_vma(), AFAICS without having taken ->mmap_sem anywhere in process? The code flow is bloody convoluted and depends on a bunch of things done by initialization, so I certainly might've missed something... Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Cc: Sakari Ailus <sakari.ailus@iki.fi> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Archit Taneja <archit@ti.com> Cc: Prabhakar Lad <prabhakar.lad@ti.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Laurent Pinchart authored
commit 317efce9 upstream. When subdev registration fails the subdev v4l2_dev field is left to a non-NULL value. Later calls to v4l2_device_unregister_subdev() will consider the subdev as registered and will module_put() the subdev module without any matching module_get(). Fix this by setting the subdev v4l2_dev field to NULL in v4l2_device_register_subdev() when the function fails. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
-
Tejun Heo authored
commit a2c1c57b upstream. To avoid executing the same work item concurrenlty, workqueue hashes currently busy workers according to their current work items and looks up the the table when it wants to execute a new work item. If there already is a worker which is executing the new work item, the new item is queued to the found worker so that it gets executed only after the current execution finishes. Unfortunately, a work item may be freed while being executed and thus recycled for different purposes. If it gets recycled for a different work item and queued while the previous execution is still in progress, workqueue may make the new work item wait for the old one although the two aren't really related in any way. In extreme cases, this false dependency may lead to deadlock although it's extremely unlikely given that there aren't too many self-freeing work item users and they usually don't wait for other work items. To alleviate the problem, record the current work function in each busy worker and match it together with the work item address in find_worker_executing_work(). While this isn't complete, it ensures that unrelated work items don't interact with each other and in the very unlikely case where a twisted wq user triggers it, it's always onto itself making the culprit easy to spot. Signed-off-by:
Tejun Heo <tj@kernel.org> Reported-by:
Andrey Isakov <andy51@gmx.ru> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=51701 [bwh: Backported to 3.2: - Adjust context - Incorporate earlier logging cleanup in process_one_work() from 044c782c ('workqueue: fix checkpatch issues')] Signed-off-by:
-
Cornelia Huck authored
commit 55c171a6 upstream. Running under a kvm host does not necessarily imply the presence of a page mapped above the main memory with the virtio information; however, the code includes a hard coded access to that page. Instead, check for the presence of the page and exit gracefully before we hit an addressing exception if it does not exist. Reviewed-by:
Marcelo Tosatti <mtosatti@redhat.com> Reviewed-by:
Alexander Graf <agraf@suse.de> Signed-off-by:
Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by:
-
Thomas Gleixner authored
commit e716efde upstream. commit 52553ddf(genirq: fix regression in irqfixup, irqpoll) introduced a potential deadlock by calling the action handler with the irq descriptor lock held. Remove the call and let the handling code run even for an interrupt where only a single action is registered. That matches the goal of the above commit and avoids the deadlock. Document the confusing action = desc->action reload in the handling loop while at it. Reported-and-tested-by:
"Wang, Warner" <warner.wang@hp.com> Tested-by:
Edward Donovan <edward.donovan@numble.net> Cc: "Wang, Song-Bo (Stoney)" <song-bo.wang@hp.com> Signed-off-by:
-
David S. Miller authored
[ Upstream commit f4d96054 ] The 'operations' bitmap corresponds one-for-one with the operation codes, no adjustment is necessary. Reported-by:
Mark Kettenis <mark.kettenis@xs4all.nl> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
- 20 Feb, 2013 8 commits
-
-
Ben Hutchings authored
-
Jan Beulich authored
commit 13d2b4d1 upstream. This fixes CVE-2013-0228 / XSA-42 Drew Jones while working on CVE-2013-0190 found that that unprivileged guest user in 32bit PV guest can use to crash the > guest with the panic like this: ------------- general protection fault: 0000 [#1] SMP last sysfs file: /sys/devices/vbd-51712/block/xvda/dev Modules linked in: sunrpc ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 xen_netfront ext4 mbcache jbd2 xen_blkfront dm_mirror dm_region_hash dm_log dm_mod [last unloaded: scsi_wait_scan] Pid: 1250, comm: r Not tainted 2.6.32-356.el6.i686 #1 EIP: 0061:[<c0407462>] EFLAGS: 00010086 CPU: 0 EIP is at xen_iret+0x12/0x2b EAX: eb8d0000 EBX: 00000001 ECX: 08049860 EDX: 00000010 ESI: 00000000 EDI: 003d0f00 EBP: b77f8388 ESP: eb8d1fe0 DS: 0000 ES: 007b FS: 0000 GS: 00e0 SS: 0069 Process r (pid: 1250, ti=eb8d0000 task=c2953550 task.ti=eb8d0000) Stack: 00000000 0027f416 00000073 00000206 b77f8364 0000007b 00000000 00000000 Call Trace: Code: c3 8b 44 24 18 81 4c 24 38 00 02 00 00 8d 64 24 30 e9 03 00 00 00 8d 76 00 f7 44 24 08 00 00 02 80 75 33 50 b8 00 e0 ff ff 21 e0 <8b> 40 10 8b 04 85 a0 f6 ab c0 8b 80 0c b0 b3 c0 f6 44 24 0d 02 EIP: [<c0407462>] xen_iret+0x12/0x2b SS:ESP 0069:eb8d1fe0 general protection fault: 0000 [#2] ---[ end trace ab0d29a492dcd330 ]--- Kernel panic - not syncing: Fatal exception Pid: 1250, comm: r Tainted: G D --------------- 2.6.32-356.el6.i686 #1 Call Trace: [<c08476df>] ? panic+0x6e/0x122 [<c084b63c>] ? oops_end+0xbc/0xd0 [<c084b260>] ? do_general_protection+0x0/0x210 [<c084a9b7>] ? error_code+0x73/ ------------- Petr says: " I've analysed the bug and I think that xen_iret() cannot cope with mangled DS, in this case zeroed out (null selector/descriptor) by either xen_failsafe_callback() or RESTORE_REGS because the corresponding LDT entry was invalidated by the reproducer. " Jan took a look at the preliminary patch and came up a fix that solves this problem: "This code gets called after all registers other than those handled by IRET got already restored, hence a null selector in %ds or a non-null one that got loaded from a code or read-only data descriptor would cause a kernel mode fault (with the potential of crashing the kernel as a whole, if panic_on_oops is set)." The way to fix this is to realize that the we can only relay on the registers that IRET restores. The two that are guaranteed are the %cs and %ss as they are always fixed GDT selectors. Also they are inaccessible from user mode - so they cannot be altered. This is the approach taken in this patch. Another alternative option suggested by Jan would be to relay on the subtle realization that using the %ebp or %esp relative references uses the %ss segment. In which case we could switch from using %eax to %ebp and would not need the %ss over-rides. That would also require one extra instruction to compensate for the one place where the register is used as scaled index. However Andrew pointed out that is too subtle and if further work was to be done in this code-path it could escape folks attention and lead to accidents. Reviewed-by:
Petr Matousek <pmatouse@redhat.com> Reported-by:
Andrew Cooper <andrew.cooper3@citrix.com> Signed-off-by:
Jan Beulich <jbeulich@suse.com> Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Nithin Nayak Sujir authored
[ Upstream commit daf3ec68 ] TG3_PHY_AUXCTL_SMDSP_ENABLE/DISABLE macros do a blind write to the phy auxiliary control register and overwrite the EXT_PKT_LEN (bit 14) resulting in intermittent crc errors on jumbo frames with some link partners. Change the code to do a read/modify/write. Signed-off-by:
Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
-
Nithin Nayak Sujir authored
[ Upstream commit 9c13cb8b ] When netconsole is enabled, logging messages generated during tg3_open can result in a null pointer dereference for the uninitialized tg3 status block. Use the irq_sync flag to disable polling in the early stages. irq_sync is cleared when the driver is enabling interrupts after all initialization is completed. Signed-off-by:
-
Sarveshwar Bandi authored
[ Upstream commit 6caab7b0 ] If lower layer driver leaves the ip header in the skb fragment, it needs to be first pulled into skb->data before inspecting ip header length or ip version number. Signed-off-by:
Sarveshwar Bandi <sarveshwar.bandi@emulex.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit ae62ca7b ] commit 35f9c09f (tcp: tcp_sendpages() should call tcp_push() once) added an internal flag : MSG_SENDPAGE_NOTLAST meant to be set on all frags but the last one for a splice() call. The condition used to set the flag in pipe_to_sendpage() relied on splice() user passing the exact number of bytes present in the pipe, or a smaller one. But some programs pass an arbitrary high value, and the test fails. The effect of this bug is a lack of tcp_push() at the end of a splice(pipe -> socket) call, and possibly very slow or erratic TCP sessions. We should both test sd->total_len and fact that another fragment is in the pipe (pipe->nrbufs > 1) Many thanks to Willy for providing very clear bug report, bisection and test programs. Reported-by:
Willy Tarreau <w@1wt.eu> Bisected-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Ilpo Järvinen authored
[ Upstream commit 6731d209 ] There are transients during normal FRTO procedure during which the packets_in_flight can go to zero between write_queue state updates and firing the resulting segments out. As FRTO processing occurs during that window the check must be more precise to not match "spuriously" :-). More specificly, e.g., when packets_in_flight is zero but FLAG_DATA_ACKED is true the problematic branch that set cwnd into zero would not be taken and new segments might be sent out later. Signed-off-by:
Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Tested-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 2e5f4212 ] Commit 9dc27415 (tcp: fix ABC in tcp_slow_start()) uncovered a bug in FRTO code : tcp_process_frto() is setting snd_cwnd to 0 if the number of in flight packets is 0. As Neal pointed out, if no packet is in flight we lost our chance to disambiguate whether a loss timeout was spurious. We should assume it was a proper loss. Reported-by:
Pasi Kärkkäinen <pasik@iki.fi> Signed-off-by:
-
