- 21 Oct, 2010 40 commits
-
-
Jarod Wilson authored
Signed-off-by:
Jarod Wilson <jarod@redhat.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
As pointed out (and tested) by Joris van Rantwijk, we do actually need to wire up .compat_ioctl for 32-bit lirc userspace to work with 64-bit lirc kernelspace. Do it. And add a check to make sure we get a valid irctl in the ioctl handler. Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
>From Joris van Rantwijk <jorispubl@xs4all.nl>: I tested lirc_serial and found that it works fine. Except the LIRC ioctls do not work in my 64-bit-kernel/32-bit-user setup. I added compat_ioctl entries in the drivers to fix this. While doing so, I noticed inconsistencies in the argument type of the LIRC ioctls. All ioctls are declared in lirc.h as having argument type __u32, however there are a few places where the driver calls get_user/put_user with an unsigned long argument. The patch below changes lirc_dev and lirc_serial to use __u32 for all ioctl arguments, and adds compat_ioctl entries. It should probably also be done in the other low-level drivers, but I don't have hardware to test those. I've dropped the .compat_ioctl addition from Joris' original patch, as I swear the non-compat definition should now work for both 32-bit and 64-bit userspace. Technically, I think we still need/want a in getting a reply to you). Reported-by:
Joris van Rantwijk <jorispubl@xs4all.nl> Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Per discussion with Andy Walls on irc, rx fifo overruns are not all that uncommon on a busy system, and the initial posting of the nuvoton-cir driver doesn't handle them well enough. With this addition, we'll drain the hw fifo, attempt to process any ir pulse trains completed with that flush, then we'll issue a hw rx fifo clear and reset the raw ir sample kfifo and start over collecting raw ir data. Also slightly refactors the cir interrupt enabling so that we always get consistent flags set and only have to modify them in one place, should they need to be altered. Signed-off-by:
-
Jarod Wilson authored
This is a new ir-core pnp driver for the Nuvoton w836x7hg integrated CIR function. The chip is found on at least the ASRock ION 330HT boxes and apparently, on a number of Intel DP55-series motherboards: http://www.asrock.com/nettop/overview.asp?Model=ION%20330HT http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=17685&lang=eng This driver was made possible by a hardware donation from Nuvoton, along with sample code (in the form of an lirc driver) and datasheet, so huge thanks to them for supporting this effort. Note that this driver constitutes a massive rewrite, porting from the lirc interfaces to the ir-core interfaces, and restructuring the driver to look more like Maxim Levitsky's ene_ir driver (as well as generally making it look more like kernel code). There's some work left to be done on this driver, to fully support the range of functionality possible, but receive and IR power-on/wake are both functional (may require setting wake key under another OS atm). The hardware I've got (one of the ASRock boxes) only supports RX, so TX is completely untested as of yet. Certain RX parameters, like sample resolution and RX IRQ sample length trigger level could possibly stand to be made tweakable via modparams or sysfs nodes, but the current values work well enough for me w/an MCE RC6A remote. The original lirc driver carried support for the Windows MCE IR keyboard/mouse device, which I plan to add back generically, in a way that should be usable by any raw IR receiver (or at least by this driver and the mceusb driver). Suspend and resume have also been tested, the power button on my remote can be used to wake the machine, and CIR functionality resumes just fine. Module unload/reload has also been tested, though not extensively or repetitively. Also tested to work with the lirc bridge plugin for userspace decoding. Signed-off-by:
-
Jean-François Moine authored
Signed-off-by:
Jean-François Moine <moinejf@free.fr> Signed-off-by:
-
Jean-François Moine authored
Signed-off-by:
-
Jean-François Moine authored
Signed-off-by:
-
Jean-François Moine authored
The new control mechanism uses dynamic control values in the subdriver descriptor. It simplifies standard control handling. Signed-off-by:
-
Laurent Pinchart authored
Take the ctrl_mutex mutex before touching control information in those functions. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Laurent Pinchart authored
XU control information is supposed to be entirely discoverable using standard UVC queries. As some devices report bogus information (such as reporting a read-only control as being read-write), add a fixup table for XU controls. This table can also be used to selectively disable requests supposed to be supported by all XU controls (GET_MIN, GET_MAX, GET_DEF, GET_RES) but not correctly (or at all) supported by the device. The table currently disables GET_CUR on the Logitech motor control XU pan/tilt controls. Signed-off-by:
-
Laurent Pinchart authored
XU controls initialization requires querying the device for control information. As some buggy UVC devices will crash when queried repeatedly in a tight loop, delay XU controls initialization until first use. Signed-off-by:
-
Laurent Pinchart authored
Now that control information structures are not shared between control instances, embed a uvc_control_info instance inside the uvc_control structure instead of storing a pointer. Signed-off-by:
-
Martin Rubli authored
This patch removes the sysadmin requirements for UVCIOC_CTRL_MAP (and the stub implementation of UVCIOC_CTRL_ADD). This requirement no longer makes sense with the new XU control access mechanisms since XU controls can be accessed without adding control mappings first. A maximum number (currently 1024) of control mappings per device is enforced to avoid excess memory consumption caused by careless user space applications. Signed-off-by:
Martin Rubli <martin_rubli@logitech.com> Signed-off-by:
-
Laurent Pinchart authored
Devices advertise XU controls using a bitmask, in which each bit corresponds to a control. The control selector, used to query the control, isn't available in the USB descriptors. All known UVC devices use control selectors equal to the control bit index plus one. Hardcode that relationship in the driver, making the UVCIOC_CTRL_ADD ioctl obsolete. All necessary information about XU controls can be obtained by the driver at enumeration time. The UVCIOC_CTRL_ADD ioctl is still supported for compatibility reasons, but now always returns -EEXIST. Finally, control mappings are now on a per-device basis and no longer global. As this changes the userspace interface, bump the driver version number to 1.0.0 (it was about time). Signed-off-by:
-
Laurent Pinchart authored
Increase the sequence number of the v4l2_buffer structure regardless of any buffer states, so that discontinuous sequence numbers allow applications to detect lost video frames. Signed-off-by:
-
Laurent Pinchart authored
The bandwidth estimate computed with the FIX_BANDIWDTH quirk is too low for many cameras. Don't use maximum packet sizes lower than 1024 bytes to try and work around the problem. According to measurements done on two different camera models, the value is high enough to get most resolutions working while not preventing two simultaneous VGA streams at 15 fps. Signed-off-by:
-
Laurent Pinchart authored
Signed-off-by:
-
Laurent Pinchart authored
Instead of printing the query hex value in error messages, print its name to make the messages more readable. Signed-off-by:
-
Laurent Pinchart authored
They're not modified by the function, make them const. Signed-off-by:
-
Laurent Pinchart authored
The Hercules Dualpix Exchange (06f8:3005) camera expose an absolute zoom that is not implemented. Blacklist it. Signed-off-by:
-
Hans Verkuil authored
Don't hold the lock before unregistering the device, since when the device is unregistered the datastruct containing the lock may be freed (if the refcount went to 0). Also fixed the framework documentation that erroneously suggested the wrong locking order as well. Reported-by:
David Ellingsworth <david@identd.dyndns.org> Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Acked-by:
-
Antti Palosaari authored
Use new RC core instead of old legacy RC implementation. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
Button is PIP => KEY_NEW http://www.linuxtv.org/wiki/index.php/Remote_ControllersSigned-off-by:
-
Antti Palosaari authored
Button is PIP => KEY_NEW http://www.linuxtv.org/wiki/index.php/Remote_Controllers Thanks to Cart. Signed-off-by:
-
Antti Palosaari authored
Fix power button mappings as defined in http://www.linuxtv.org/wiki/index.php/Remote_ControllersSigned-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Rename remote controller driver I added earlier. Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Imported from af9015.h. Initial keytable was from Jose Alberto Reguero <jareguero@telefonica.net> and Felipe Morales Moreno <felipe.morales.moreno@gmail.com> Signed-off-by:
-
Antti Palosaari authored
Digittrade DVB-T USB Stick remote controller. Imported from af9015.h. Initial keytable was from Alain Kalker <miki@dds.nl> Signed-off-by:
-
Antti Palosaari authored
Imported from af9015.h. Initial keytable was from Marc Schneider <macke@macke.org> Signed-off-by:
-
Antti Palosaari authored
MSI DIGIVOX mini III remote controller. Uses NEC extended 0x61d6. This remote seems to be same as rc-kworld-315u.c. Anyhow, add new remote since rc-kworld-315u.c lacks NEC extended address byte. Signed-off-by:
-
Antti Palosaari authored
TerraTec slim remote, 7 rows, 4 columns. Uses NEC extended 0x02bd. Signed-off-by:
-
