[ Upstream commit d9b2997e ]

Add a quirk for WORLDE easykey.25 MIDI keyboard (idVendor=0218,
idProduct=0401). The device reports that it has config string
descriptor at index 3, but when the system selects the configuration
and tries to get the description, it returns a -EPROTO error,
the communication restarts and this keeps repeating over and over again.
Not requesting the string descriptor makes the device work correctly.

Relevant info from Wireshark:

[...]

CONFIGURATION DESCRIPTOR
    bLength: 9
    bDescriptorType: 0x02 (CONFIGURATION)
    wTotalLength: 101
    bNumInterfaces: 2
    bConfigurationValue: 1
    iConfiguration: 3
    Configuration bmAttributes: 0xc0  SELF-POWERED  NO REMOTE-WAKEUP
        1... .... = Must be 1: Must be 1 for USB 1.1 and higher
        .1.. .... = Self-Powered: This device is SELF-POWERED
        ..0. .... = Remote Wakeup: This device does NOT support remote wakeup
    bMaxPower: 50  (100mA)

[...]

     45 0.369104       host                  2.38.0                USB      64     GET DESCRIPTOR Request STRING

[...]

URB setup
    bmRequestType: 0x80
        1... .... = Direction: Device-to-host
        .00. .... = Type: Standard (0x00)
        ...0 0000 = Recipient: Device (0x00)
    bRequest: GET DESCRIPTOR (6)
    Descriptor Index: 0x03
    bDescriptorType: 0x03
    Language Id: English (United States) (0x0409)
    wLength: 255

     46 0.369255       2.38.0                host                  USB      64     GET DESCRIPTOR Response STRING[Malformed Packet]

[...]

Frame 46: 64 bytes on wire (512 bits), 64 bytes captured (512 bits) on interface 0
USB URB
    [Source: 2.38.0]
    [Destination: host]
    URB id: 0xffff88021f62d480
    URB type: URB_COMPLETE ('C')
    URB transfer type: URB_CONTROL (0x02)
    Endpoint: 0x80, Direction: IN
    Device: 38
    URB bus id: 2
    Device setup request: not relevant ('-')
    Data: present (0)
    URB sec: 1484896277
    URB usec: 455031
    URB status: Protocol error (-EPROTO) (-71)
    URB length [bytes]: 0
    Data length [bytes]: 0
    [Request in: 45]
    [Time from request: 0.000151000 seconds]
    Unused Setup Header
    Interval: 0
    Start frame: 0
    Copy of Transfer Flags: 0x00000200
    Number of ISO descriptors: 0
[Malformed Packet: USB]
    [Expert Info (Error/Malformed): Malformed Packet (Exception occurred)]
        [Malformed Packet (Exception occurred)]
        [Severity level: Error]
        [Group: Malformed]
Signed-off-by: Lukáš Lalinský <lukas@oxygene.sk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 2dc705a9 ]

Copying color maps to userspace doesn't check the value of to->start,
which will cause kernel heap buffer OOB read due to signedness wraps.

CVE-2016-8405

Link: http://lkml.kernel.org/r/20170105224249.GA50925@beast
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Peter Pi (@heisecode) of Trend Micro
Cc: Min Chong <mchong@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit d51e9894 ]

Since commit be97a41b ("mm/mempolicy.c: merge alloc_hugepage_vma to
alloc_pages_vma") alloc_pages_vma() can potentially free a mempolicy by
mpol_cond_put() before accessing the embedded nodemask by
__alloc_pages_nodemask().  The commit log says it's so "we can use a
single exit path within the function" but that's clearly wrong.  We can
still do that when doing mpol_cond_put() after the allocation attempt.

Make sure the mempolicy is not freed prematurely, otherwise
__alloc_pages_nodemask() can end up using a bogus nodemask, which could
lead e.g.  to premature OOM.

Fixes: be97a41b ("mm/mempolicy.c: merge alloc_hugepage_vma to alloc_pages_vma")
Link: http://lkml.kernel.org/r/20170118141124.8345-1-vbabka@suse.czSigned-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>	[4.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit c929ea0b ]

After removing sunrpc module, I get many kmemleak information as,
unreferenced object 0xffff88003316b1e0 (size 544):
  comm "gssproxy", pid 2148, jiffies 4294794465 (age 4200.081s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffffb0cfb58a>] kmemleak_alloc+0x4a/0xa0
    [<ffffffffb03507fe>] kmem_cache_alloc+0x15e/0x1f0
    [<ffffffffb0639baa>] ida_pre_get+0xaa/0x150
    [<ffffffffb0639cfd>] ida_simple_get+0xad/0x180
    [<ffffffffc06054fb>] nlmsvc_lookup_host+0x4ab/0x7f0 [lockd]
    [<ffffffffc0605e1d>] lockd+0x4d/0x270 [lockd]
    [<ffffffffc06061e5>] param_set_timeout+0x55/0x100 [lockd]
    [<ffffffffc06cba24>] svc_defer+0x114/0x3f0 [sunrpc]
    [<ffffffffc06cbbe7>] svc_defer+0x2d7/0x3f0 [sunrpc]
    [<ffffffffc06c71da>] rpc_show_info+0x8a/0x110 [sunrpc]
    [<ffffffffb044a33f>] proc_reg_write+0x7f/0xc0
    [<ffffffffb038e41f>] __vfs_write+0xdf/0x3c0
    [<ffffffffb0390f1f>] vfs_write+0xef/0x240
    [<ffffffffb0392fbd>] SyS_write+0xad/0x130
    [<ffffffffb0d06c37>] entry_SYSCALL_64_fastpath+0x1a/0xa9
    [<ffffffffffffffff>] 0xffffffffffffffff

I found, the ida information (dynamic memory) isn't cleanup.
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Fixes: 2f048db4 ("SUNRPC: Add an identifier for struct rpc_clnt")
Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 059aa734 ]

Xuan Qi reports that the Linux NFSv4 client failed to lock a file
that was migrated. The steps he observed on the wire:

1. The client sent a LOCK request to the source server
2. The source server replied NFS4ERR_MOVED
3. The client switched to the destination server
4. The client sent the same LOCK request to the destination
   server with a bumped lock sequence ID
5. The destination server rejected the LOCK request with
   NFS4ERR_BAD_SEQID

RFC 3530 section 8.1.5 provides a list of NFS errors which do not
bump a lock sequence ID.

However, RFC 3530 is now obsoleted by RFC 7530. In RFC 7530 section
9.1.7, this list has been updated by the addition of NFS4ERR_MOVED.
Reported-by: Xuan Qi <xuan.qi@oracle.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 5d03a2fd ]

Yet another laptop vendor rebranded Novatel E371.

Cc: stable@vger.kernel.org
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit f05fea5b ]

In __eeh_clear_pe_frozen_state(), we should pass the flag's value
instead of its address to eeh_unfreeze_pe(). The isolated flag is
cleared if no error returned from __eeh_clear_pe_frozen_state(). We
never observed the error from the function. So the isolated flag should
have been always cleared, no real issue is caused because of the misused
@flag.

This fixes the code by passing the value of @flag to eeh_unfreeze_pe().

Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit af2b7fa1 ]

prom_init.c calls 'instance-to-package' twice, but the return
is not checked during prom_find_boot_cpu(). The result is then
passed to prom_getprop(), which could be PROM_ERROR. Add a return check
to prevent this.

This was found on a pasemi system, where CFE doesn't have a working
'instance-to package' prom call.

Before Commit 5c0484e2 ('powerpc: Endian safe trampoline') the area
around addr 0 was mostly 0's and this doesn't cause a problem. Once the
macro 'FIXUP_ENDIAN' has been added to head_64.S, the low memory area
now has non-zero values, which cause the prom_getprop() call
to hang.

mpe: Also confirmed that under SLOF if 'instance-to-package' did fail
with PROM_ERROR we would crash in SLOF. So the bug is not specific to
CFE, it's just that other open firmwares don't trigger it because they
have a working 'instance-to-package'.

Fixes: 5c0484e2 ("powerpc: Endian safe trampoline")
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 11e3b725 ]

Update the ARMv8 Crypto Extensions and the plain NEON AES implementations
in CBC and CTR modes to return the next IV back to the skcipher API client.
This is necessary for chaining to work correctly.

Note that for CTR, this is only done if the request is a round multiple of
the block size, since otherwise, chaining is impossible anyway.

Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit d6040764 ]

Make sure CRYPTO_ALG_DEAD bit is cleared before proceeding with
the algorithm registration. This fixes qat-dh registration when
driver is restarted

Cc: <stable@vger.kernel.org>
Signed-off-by: Salvatore Benedetto <salvatore.benedetto@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 43849785 ]

Read access to the SPI flash are broken on da850-evm, i.e. the data
read is not what is actually programmed on the flash.
According to the datasheet for the M25P64 part present on the da850-evm,
if the SPI frequency is higher than 20MHz then the READ command is not
usable anymore and only the FAST_READ command can be used to read data.

This commit specifies in the DTS that we should use FAST_READ command
instead of the READ command.

Cc: stable@vger.kernel.org
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[nsekhar@ti.com: subject line adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 24d615a6 ]

The Dell DW5570 is a re-branded Sierra Wireless MC8805 which will by
default boot with vid 0x413c and pid 0x81a3. When triggered QDL download
mode, the device switches to pid 0x81a6 and provides the standard TTY
used for firmware upgrade.

Cc: <stable@vger.kernel.org>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit ad9e202a ]

We cannot preserve partial fields for hardware breakpoints, because
the values written by userspace to the hardware breakpoint
registers can't subsequently be recovered intact from the hardware.

So, just reject attempts to write incomplete fields with -EINVAL.

Cc: <stable@vger.kernel.org> # 3.7.x-
Fixes: 478fcb2c ("arm64: Debugging support")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit aeb1f39d ]

This patch adds an explicit __reserved[] field to user_fpsimd_state
to replace what was previously unnamed padding.

This ensures that data in this region are propagated across
assignment rather than being left possibly uninitialised at the
destination.

Cc: <stable@vger.kernel.org> # 3.7.x-
Fixes: 60ffc30d ("arm64: Exception handling")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 9a17b876 ]

Ensure that if userspace supplies insufficient data to
PTRACE_SETREGSET to fill all the registers, the thread's old
registers are preserved.

Cc: <stable@vger.kernel.org> # 3.7.x-
Fixes: 478fcb2c ("arm64: Debugging support")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 6df8c9d8 ]

sparse says:

    fs/ceph/mds_client.c:291:23: warning: restricted __le32 degrades to integer
    fs/ceph/mds_client.c:293:28: warning: restricted __le32 degrades to integer
    fs/ceph/mds_client.c:294:28: warning: restricted __le32 degrades to integer
    fs/ceph/mds_client.c:296:28: warning: restricted __le32 degrades to integer

The op value is __le32, so we need to convert it before comparing it.

Cc: stable@vger.kernel.org # needs backporting for < 3.14
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit befa6011 ]

In order to make the driver work with the common clock framework, this
patch converts the clk_enable()/clk_disable() to
clk_prepare_enable()/clk_disable_unprepare().

Also add error checking for clk_prepare_enable().
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit c97c52be ]

The priv->device pointer for c_can_pci is never set, but it is used
without a NULL check in c_can_start(). Setting it in c_can_pci_probe()
like c_can_plat_probe() prevents c_can_pci.ko from crashing, with and
without CONFIG_PM.

This might also cause the pm_runtime_*() functions in c_can.c to
actually be executed for c_can_pci devices - they are the only other
place where priv->device is used, but they all contain a null check.
Signed-off-by: Einar Jón <tolvupostur@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit fc1ffd6c ]

During code inspection, while investigating following stack trace
seen on one of the test setup, we found out there was possibility
of memory leak becuase driver was not unwinding the stack properly.

This issue has not been reproduced in a test environment or on a
customer setup.

Here's stack trace that was seen.

[1469877.797315] Call Trace:
[1469877.799940]  [<ffffffffa03ab6e9>] qla2x00_mem_alloc+0xb09/0x10c0 [qla2xxx]
[1469877.806980]  [<ffffffffa03ac50a>] qla2x00_probe_one+0x86a/0x1b50 [qla2xxx]
[1469877.814013]  [<ffffffff813b6d01>] ? __pm_runtime_resume+0x51/0xa0
[1469877.820265]  [<ffffffff8157c1f5>] ? _raw_spin_lock_irqsave+0x25/0x90
[1469877.826776]  [<ffffffff8157cd2d>] ? _raw_spin_unlock_irqrestore+0x6d/0x80
[1469877.833720]  [<ffffffff810741d1>] ? preempt_count_sub+0xb1/0x100
[1469877.839885]  [<ffffffff8157cd0c>] ? _raw_spin_unlock_irqrestore+0x4c/0x80
[1469877.846830]  [<ffffffff81319b9c>] local_pci_probe+0x4c/0xb0
[1469877.852562]  [<ffffffff810741d1>] ? preempt_count_sub+0xb1/0x100
[1469877.858727]  [<ffffffff81319c89>] pci_call_probe+0x89/0xb0

Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed spelling in patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 1cb51a15 ]

When replaying the journal it can happen that a journal entry points to
a garbage collected node.
This is the case when a power-cut occurred between a garbage collect run
and a commit. In such a case nodes have to be read using the failable
read functions to detect whether the found node matches what we expect.

One corner case was forgotten, when the journal contains an entry to
remove an inode all xattrs have to be removed too. UBIFS models xattr
like directory entries, so the TNC code iterates over
all xattrs of the inode and removes them too. This code re-uses the
functions for walking directories and calls ubifs_tnc_next_ent().
ubifs_tnc_next_ent() expects to be used only after the journal and
aborts when a node does not match the expected result. This behavior can
render an UBIFS volume unmountable after a power-cut when xattrs are
used.

Fix this issue by using failable read functions in ubifs_tnc_next_ent()
too when replaying the journal.
Cc: stable@vger.kernel.org
Fixes: 1e51764a ("UBIFS: add new flash file system")
Reported-by: Rock Lee <rockdotlee@gmail.com>
Reviewed-by: David Gstir <david@sigma-star.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 78794d18 ]

Context expiry times are in units of seconds since boot, not unix time.

The use of get_seconds() here therefore sets the expiry time decades in
the future.  This prevents timely freeing of contexts destroyed by
client RPC_GSS_PROC_DESTROY requests.  We'd still free them eventually
(when the module is unloaded or the container shut down), but a lot of
contexts could pile up before then.

Cc: stable@vger.kernel.org
Fixes: c5b29f88 "sunrpc: use seconds since boot in expiry cache"
Reported-by: Andy Adamson <andros@netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit cef84c30 ]

KVM's lapic emulation uses static_key_deferred (apic_{hw,sw}_disabled).
These are implemented with delayed_work structs which can still be
pending when the KVM module is unloaded. We've seen this cause kernel
panics when the kvm_intel module is quickly reloaded.

Use the new static_key_deferred_flush() API to flush pending updates on
module unload.
Signed-off-by: David Matlack <dmatlack@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit b6416e61 ]

Modules that use static_key_deferred need a way to synchronize with
any delayed work that is still pending when the module is unloaded.
Introduce static_key_deferred_flush() which flushes any pending
jump label updates.
Signed-off-by: David Matlack <dmatlack@google.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 01167c7b ]

According to the code the intention is to append 8 SCK cycles
instead of 4 at end of a MMC_STOP_TRANSMISSION command. But this
will never happened because it's an AC command not an ADTC command.
So fix this by moving the statement into the right function.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: e4243f13 (mmc: mxs-mmc: add mmc host driver for i.MX23/28)
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit fdf35a6b ]

I noticed that the VT switch doesn't work any longer with a Dell
laptop with 1366x768 eDP when the machine is connected with a DP
monitor.  It behaves as if VT were switched, but the graphics remain
frozen.  Actually the keyboard works, so I could switch back to VT7
again.

I tried to track down the problem, and encountered a long story until
we reach to this error:

- The machine is booted with video=1366x768 option (the distro
  installer seems to add it as default).
- Recently, drm_helper_probe_single_connector_modes() deals with
  cmdline modes, and it tries to create a new mode when no
  matching mode is found.
- The drm_mode_create_from_cmdline_mode() creates a mode based on
  either CVT of GFT according to the given cmdline mode; in our case,
  it's 1366x768.
- Since both CVT and GFT can't express the width 1366 due to
  alignment, the resultant mode becomes 1368x768, slightly larger than
  the given size.
- Later on, the atomic commit is performed, and in
  drm_atomic_check_only(), the size of each plane is checked.
- The size check of 1366x768 fails due to the above, and eventually
  the whole VT switch fails.

Back in the history, we've had a manual fix-up of 1368x768 in various
places via c09dedb7 ("drm/edid: Add a workaround for 1366x768 HD
panel"), but they have been all in drm_edid.c at probing the modes
from EDID.  For addressing the problem above, we need a similar hack
to the mode newly created from cmdline, manually adjusting the width
when the expected size is 1366 while we get 1368 instead.

Fixes: eaf99c74 ("drm: Perform cmdline mode parsing during...")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: http://patchwork.freedesktop.org/patch/msgid/20170109145614.29454-1-tiwai@suse.deReviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit d6169d04 ]

If a URB is killed while the host is removed we can end up in a situation
where the hub thread takes the roothub device lock, and waits for
the URB to be given back by xhci-hcd, blocking the host remove code.

xhci-hcd tries to stop the endpoint and give back the urb, but can't
as the host is removed from PCI bus at the same time, preventing the normal
way of giving back urb.

Instead we need to rely on the stop command timeout function to give back
the urb. This xhci_stop_endpoint_command_watchdog() timeout function
used a XHCI_STATE_DYING flag to indicate if the timeout function is already
running, but later this flag has been taking into use in other places to
mark that xhci is dying.

Remove checks for XHCI_STATE_DYING in xhci_urb_dequeue. We are still
checking that reading from pci state does not return 0xffffffff or that
host is not halted before trying to stop the endpoint.

This whole area of stopping endpoints, giving back URBs, and the wathdog
timeout need rework, this fix focuses on solving a specific deadlock
issue that we can then send to stable before any major rework.

Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 51ebfc92 ]

A PCI-to-PCIe bridge (a "reverse bridge") has a PCI or PCI-X primary
interface and a PCI Express secondary interface.  The PCIe interface is a
Downstream Port that originates a Link.  See the "PCI Express to PCI/PCI-X
Bridge Specification", rev 1.0, sections 1.2 and A.6.

The bug report below involves a PCI-to-PCIe bridge and a PCIe switch below
the bridge:

  00:1e.0 Intel 82801 PCI Bridge to [bus 01-0a]
  01:00.0 Pericom PI7C9X111SL PCIe-to-PCI Reversible Bridge to [bus 02-0a]
  02:00.0 Pericom Device 8608 [PCIe Upstream Port] to [bus 03-0a]
  03:01.0 Pericom Device 8608 [PCIe Downstream Port] to [bus 0a]

01:00.0 is configured as a PCI-to-PCIe bridge (despite the name printed by
lspci).  As we traverse a PCIe hierarchy, device connections alternate
between PCIe Links and internal Switch logic.  Previously we did not
recognize that 01:00.0 had a secondary link, so we thought the 02:00.0
Upstream Port *did* have a secondary link.  In fact, it's the other way
around: 01:00.0 has a secondary link, and 02:00.0 has internal Switch logic
on its secondary side.

When we thought 02:00.0 had a secondary link, the pci_scan_slot() ->
only_one_child() path assumed 02:00.0 could have only one child, so 03:00.0
was the only possible downstream device.  But 03:00.0 doesn't exist, so we
didn't look for any other devices on bus 03.

Booting with "pci=pcie_scan_all" is a workaround, but we don't want users
to have to do that.

Recognize that PCI-to-PCIe bridges originate links on their secondary
interfaces.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=189361
Fixes: d0751b98 ("PCI: Add dev->has_secondary_link to track downstream PCIe links")
Tested-by: Blake Moore <blake.moore@men.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org	# v4.2+
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 89e9f7bc ]

Martin reported that the Supermicro X8DTH-i/6/iF/6F advertises incorrect
host bridge windows via _CRS:

  pci_root PNP0A08:00: host bridge window [io  0xf000-0xffff]
  pci_root PNP0A08:01: host bridge window [io  0xf000-0xffff]

Both bridges advertise the 0xf000-0xffff window, which cannot be correct.

Work around this by ignoring _CRS on this system.  The downside is that we
may not assign resources correctly to hot-added PCI devices (if they are
possible on this system).

Link: https://bugzilla.kernel.org/show_bug.cgi?id=42606Reported-by: Martin Burnicki <martin.burnicki@meinberg.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 2d5a9c72 ]

A short control transfer would currently fail to be detected, something
which could lead to stale buffer data being used as valid input.

Check for short transfers, and make sure to log any transfer errors.

Note that this also avoids leaking heap data to user space (TIOCMGET)
and the remote device (break control).

Fixes: 6ce76104 ("USB: Driver for CH341 USB-serial adaptor")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit c8a6a09c ]

In ca91cx42_slave_get function, the value pointed by vme_base pointer is
set through:

*vme_base = ioread32(bridge->base + CA91CX42_VSI_BS[i]);

So it must be dereferenced to be used in calculation of pci_base:

*pci_base = (dma_addr_t)*vme_base + pci_offset;

This bug was caught thanks to the following gcc warning:

drivers/vme/bridges/vme_ca91cx42.c: In function ‘ca91cx42_slave_get’:
drivers/vme/bridges/vme_ca91cx42.c:467:14: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
*pci_base = (dma_addr_t)vme_base + pci_offset;
Signed-off-by: Augusto Mecking Caringi <augustocaringi@gmail.com>
Acked-By: Martyn Welch <martyn@welchs.me.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 802c0388 ]

The sysrq input handler should be attached to the input device which has
a left alt key.

On 32-bit kernels, some input devices which has a left alt key cannot
attach sysrq handler.  Because the keybit bitmap in struct input_device_id
for sysrq is not correctly initialized.  KEY_LEFTALT is 56 which is
greater than BITS_PER_LONG on 32-bit kernels.

I found this problem when using a matrix keypad device which defines
a KEY_LEFTALT (56) but doesn't have a KEY_O (24 == 56%32).

Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit e5bbc8a6 ]

return_unused_surplus_pages() decrements the global reservation count,
and frees any unused surplus pages that were backing the reservation.

Commit 7848a4bf ("mm/hugetlb.c: add cond_resched_lock() in
return_unused_surplus_pages()") added a call to cond_resched_lock in the
loop freeing the pages.

As a result, the hugetlb_lock could be dropped, and someone else could
use the pages that will be freed in subsequent iterations of the loop.
This could result in inconsistent global hugetlb page state, application
api failures (such as mmap) failures or application crashes.

When dropping the lock in return_unused_surplus_pages, make sure that
the global reservation count (resv_huge_pages) remains sufficiently
large to prevent someone else from claiming pages about to be freed.

Analyzed by Paul Cassella.

Fixes: 7848a4bf ("mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()")
Link: http://lkml.kernel.org/r/1483991767-6879-1-git-send-email-mike.kravetz@oracle.comSigned-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reported-by: Paul Cassella <cassella@cray.com>
Suggested-by: Michal Hocko <mhocko@kernel.org>
Cc: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: <stable@vger.kernel.org>	[3.15+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit e7ee2c08 ]

The crash happens rather often when we reset some cluster nodes while
nodes contend fiercely to do truncate and append.

The crash backtrace is below:

   dlm: C21CBDA5E0774F4BA5A9D4F317717495: dlm_recover_grant 1 locks on 971 resources
   dlm: C21CBDA5E0774F4BA5A9D4F317717495: dlm_recover 9 generation 5 done: 4 ms
   ocfs2: Begin replay journal (node 318952601, slot 2) on device (253,18)
   ocfs2: End replay journal (node 318952601, slot 2) on device (253,18)
   ocfs2: Beginning quota recovery on device (253,18) for slot 2
   ocfs2: Finishing quota recovery on device (253,18) for slot 2
   (truncate,30154,1):ocfs2_truncate_file:470 ERROR: bug expression: le64_to_cpu(fe->i_size) != i_size_read(inode)
   (truncate,30154,1):ocfs2_truncate_file:470 ERROR: Inode 290321, inode i_size = 732 != di i_size = 937, i_flags = 0x1
   ------------[ cut here ]------------
   kernel BUG at /usr/src/linux/fs/ocfs2/file.c:470!
   invalid opcode: 0000 [#1] SMP
   Modules linked in: ocfs2_stack_user(OEN) ocfs2(OEN) ocfs2_nodemanager ocfs2_stackglue(OEN) quota_tree dlm(OEN) configfs fuse sd_mod    iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi af_packet iscsi_ibft iscsi_boot_sysfs softdog xfs libcrc32c ppdev parport_pc pcspkr parport      joydev virtio_balloon virtio_net i2c_piix4 acpi_cpufreq button processor ext4 crc16 jbd2 mbcache ata_generic cirrus virtio_blk ata_piix               drm_kms_helper ahci syscopyarea libahci sysfillrect sysimgblt fb_sys_fops ttm floppy libata drm virtio_pci virtio_ring uhci_hcd virtio ehci_hcd       usbcore serio_raw usb_common sg dm_multipath dm_mod scsi_dh_rdac scsi_dh_emc scsi_dh_alua scsi_mod autofs4
   Supported: No, Unsupported modules are loaded
   CPU: 1 PID: 30154 Comm: truncate Tainted: G           OE   N  4.4.21-69-default #1
   Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.1-0-g4adadbd-20151112_172657-sheep25 04/01/2014
   task: ffff88004ff6d240 ti: ffff880074e68000 task.ti: ffff880074e68000
   RIP: 0010:[<ffffffffa05c8c30>]  [<ffffffffa05c8c30>] ocfs2_truncate_file+0x640/0x6c0 [ocfs2]
   RSP: 0018:ffff880074e6bd50  EFLAGS: 00010282
   RAX: 0000000000000074 RBX: 000000000000029e RCX: 0000000000000000
   RDX: 0000000000000001 RSI: 0000000000000246 RDI: 0000000000000246
   RBP: ffff880074e6bda8 R08: 000000003675dc7a R09: ffffffff82013414
   R10: 0000000000034c50 R11: 0000000000000000 R12: ffff88003aab3448
   R13: 00000000000002dc R14: 0000000000046e11 R15: 0000000000000020
   FS:  00007f839f965700(0000) GS:ffff88007fc80000(0000) knlGS:0000000000000000
   CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
   CR2: 00007f839f97e000 CR3: 0000000036723000 CR4: 00000000000006e0
   Call Trace:
     ocfs2_setattr+0x698/0xa90 [ocfs2]
     notify_change+0x1ae/0x380
     do_truncate+0x5e/0x90
     do_sys_ftruncate.constprop.11+0x108/0x160
     entry_SYSCALL_64_fastpath+0x12/0x6d
   Code: 24 28 ba d6 01 00 00 48 c7 c6 30 43 62 a0 8b 41 2c 89 44 24 08 48 8b 41 20 48 c7 c1 78 a3 62 a0 48 89 04 24 31 c0 e8 a0 97 f9 ff <0f> 0b 3d 00 fe ff ff 0f 84 ab fd ff ff 83 f8 fc 0f 84 a2 fd ff
   RIP  [<ffffffffa05c8c30>] ocfs2_truncate_file+0x640/0x6c0 [ocfs2]

It's because ocfs2_inode_lock() get us stale LVB in which the i_size is
not equal to the disk i_size.  We mistakenly trust the LVB because the
underlaying fsdlm dlm_lock() doesn't set lkb_sbflags with
DLM_SBF_VALNOTVALID properly for us.  But, why?

The current code tries to downconvert lock without DLM_LKF_VALBLK flag
to tell o2cb don't update RSB's LVB if it's a PR->NULL conversion, even
if the lock resource type needs LVB.  This is not the right way for
fsdlm.

The fsdlm plugin behaves different on DLM_LKF_VALBLK, it depends on
DLM_LKF_VALBLK to decide if we care about the LVB in the LKB.  If
DLM_LKF_VALBLK is not set, fsdlm will skip recovering RSB's LVB from
this lkb and set the right DLM_SBF_VALNOTVALID appropriately when node
failure happens.

The following diagram briefly illustrates how this crash happens:

RSB1 is inode metadata lock resource with LOCK_TYPE_USES_LVB;

The 1st round:

             Node1                                    Node2
RSB1: PR
                                                  RSB1(master): NULL->EX
ocfs2_downconvert_lock(PR->NULL, set_lvb==0)
  ocfs2_dlm_lock(no DLM_LKF_VALBLK)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

dlm_lock(no DLM_LKF_VALBLK)
  convert_lock(overwrite lkb->lkb_exflags
               with no DLM_LKF_VALBLK)

RSB1: NULL                                        RSB1: EX
                                                  reset Node2
dlm_recover_rsbs()
  recover_lvb()

/* The LVB is not trustable if the node with EX fails and
 * no lock >= PR is left. We should set RSB_VALNOTVALID for RSB1.
 */

 if(!(kb_exflags & DLM_LKF_VALBLK)) /* This means we miss the chance to
           return;                   * to invalid the LVB here.
                                     */

The 2nd round:

         Node 1                                Node2
RSB1(become master from recovery)

ocfs2_setattr()
  ocfs2_inode_lock(NULL->EX)
    /* dlm_lock() return the stale lvb without setting DLM_SBF_VALNOTVALID */
    ocfs2_meta_lvb_is_trustable() return 1 /* so we don't refresh inode from disk */
  ocfs2_truncate_file()
      mlog_bug_on_msg(disk isize != i_size_read(inode))  /* crash! */

The fix is quite straightforward.  We keep to set DLM_LKF_VALBLK flag
for dlm_lock() if the lock resource type needs LVB and the fsdlm plugin
is uesed.

Link: http://lkml.kernel.org/r/1481275846-6604-1-git-send-email-zren@suse.comSigned-off-by: Eric Ren <zren@suse.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit ddc37832 ]

On APQ8060, the kernel crashes in arch_hw_breakpoint_init, taking an
undefined instruction trap within write_wb_reg. This is because Scorpion
CPUs erroneously appear to set DBGPRSR.SPD when WFI is issued, even if
the core is not powered down. When DBGPRSR.SPD is set, breakpoint and
watchpoint registers are treated as undefined.

It's possible to trigger similar crashes later on from userspace, by
requesting the kernel to install a breakpoint or watchpoint, as we can
go idle at any point between the reset of the debug registers and their
later use. This has always been the case.

Given that this has always been broken, no-one has complained until now,
and there is no clear workaround, disable hardware breakpoints and
watchpoints on Scorpion to avoid these issues.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 146cc8a1 ]

The current implementation failed to detect short transfers when
attempting to read the line state, and also, to make things worse,
logged the content of the uninitialised heap transfer buffer.

Fixes: abf492e7 ("USB: kl5kusb105: fix DMA buffers on stack")
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 2e40795c ]

Plantronics BT600 does not support reading the sample rate which leads
to many lines of "cannot get freq at ep 0x1" and "cannot get freq at
ep 0x82". This patch adds the USB ID of the BT600 to quirks.c and
avoids those error messages.
Signed-off-by: Dennis Kadioglu <denk@post.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 93362fa4 ]

Fixes CVE-2016-9191, proc_sys_readdir doesn't drop reference
added by grab_header when return from !dir_emit_dots path.
It can cause any path called unregister_sysctl_table will
wait forever.

The calltrace of CVE-2016-9191:

[ 5535.960522] Call Trace:
[ 5535.963265]  [<ffffffff817cdaaf>] schedule+0x3f/0xa0
[ 5535.968817]  [<ffffffff817d33fb>] schedule_timeout+0x3db/0x6f0
[ 5535.975346]  [<ffffffff817cf055>] ? wait_for_completion+0x45/0x130
[ 5535.982256]  [<ffffffff817cf0d3>] wait_for_completion+0xc3/0x130
[ 5535.988972]  [<ffffffff810d1fd0>] ? wake_up_q+0x80/0x80
[ 5535.994804]  [<ffffffff8130de64>] drop_sysctl_table+0xc4/0xe0
[ 5536.001227]  [<ffffffff8130de17>] drop_sysctl_table+0x77/0xe0
[ 5536.007648]  [<ffffffff8130decd>] unregister_sysctl_table+0x4d/0xa0
[ 5536.014654]  [<ffffffff8130deff>] unregister_sysctl_table+0x7f/0xa0
[ 5536.021657]  [<ffffffff810f57f5>] unregister_sched_domain_sysctl+0x15/0x40
[ 5536.029344]  [<ffffffff810d7704>] partition_sched_domains+0x44/0x450
[ 5536.036447]  [<ffffffff817d0761>] ? __mutex_unlock_slowpath+0x111/0x1f0
[ 5536.043844]  [<ffffffff81167684>] rebuild_sched_domains_locked+0x64/0xb0
[ 5536.051336]  [<ffffffff8116789d>] update_flag+0x11d/0x210
[ 5536.057373]  [<ffffffff817cf61f>] ? mutex_lock_nested+0x2df/0x450
[ 5536.064186]  [<ffffffff81167acb>] ? cpuset_css_offline+0x1b/0x60
[ 5536.070899]  [<ffffffff810fce3d>] ? trace_hardirqs_on+0xd/0x10
[ 5536.077420]  [<ffffffff817cf61f>] ? mutex_lock_nested+0x2df/0x450
[ 5536.084234]  [<ffffffff8115a9f5>] ? css_killed_work_fn+0x25/0x220
[ 5536.091049]  [<ffffffff81167ae5>] cpuset_css_offline+0x35/0x60
[ 5536.097571]  [<ffffffff8115aa2c>] css_killed_work_fn+0x5c/0x220
[ 5536.104207]  [<ffffffff810bc83f>] process_one_work+0x1df/0x710
[ 5536.110736]  [<ffffffff810bc7c0>] ? process_one_work+0x160/0x710
[ 5536.117461]  [<ffffffff810bce9b>] worker_thread+0x12b/0x4a0
[ 5536.123697]  [<ffffffff810bcd70>] ? process_one_work+0x710/0x710
[ 5536.130426]  [<ffffffff810c3f7e>] kthread+0xfe/0x120
[ 5536.135991]  [<ffffffff817d4baf>] ret_from_fork+0x1f/0x40
[ 5536.142041]  [<ffffffff810c3e80>] ? kthread_create_on_node+0x230/0x230

One cgroup maintainer mentioned that "cgroup is trying to offline
a cpuset css, which takes place under cgroup_mutex.  The offlining
ends up trying to drain active usages of a sysctl table which apprently
is not happening."
The real reason is that proc_sys_readdir doesn't drop reference added
by grab_header when return from !dir_emit_dots path. So this cpuset
offline path will wait here forever.

See here for details: http://www.openwall.com/lists/oss-security/2016/11/04/13

Fixes: f0c3b509 ("[readdir] convert procfs")
Cc: stable@vger.kernel.org
Reported-by: CAI Qian <caiqian@redhat.com>
Tested-by: Yang Shukui <yangshukui@huawei.com>
Signed-off-by: Zhou Chengming <zhouchengming1@huawei.com>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 3895dbf8 ]

Protecting the mountpoint hashtable with namespace_sem was sufficient
until a call to umount_mnt was added to mntput_no_expire.  At which
point it became possible for multiple calls of put_mountpoint on
the same hash chain to happen on the same time.

Kristen Johansen <kjlx@templeofstupid.com> reported:
> This can cause a panic when simultaneous callers of put_mountpoint
> attempt to free the same mountpoint.  This occurs because some callers
> hold the mount_hash_lock, while others hold the namespace lock.  Some
> even hold both.
>
> In this submitter's case, the panic manifested itself as a GP fault in
> put_mountpoint() when it called hlist_del() and attempted to dereference
> a m_hash.pprev that had been poisioned by another thread.

Al Viro observed that the simple fix is to switch from using the namespace_sem
to the mount_lock to protect the mountpoint hash table.

I have taken Al's suggested patch moved put_mountpoint in pivot_root
(instead of taking mount_lock an additional time), and have replaced
new_mountpoint with get_mountpoint a function that does the hash table
lookup and addition under the mount_lock.   The introduction of get_mounptoint
ensures that only the mount_lock is needed to manipulate the mountpoint
hashtable.

d_set_mounted is modified to only set DCACHE_MOUNTED if it is not
already set.  This allows get_mountpoint to use the setting of
DCACHE_MOUNTED to ensure adding a struct mountpoint for a dentry
happens exactly once.

Cc: stable@vger.kernel.org
Fixes: ce07d891 ("mnt: Honor MNT_LOCKED when detaching mounts")
Reported-by: Krister Johansen <kjlx@templeofstupid.com>
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit f2950b78 ]

Make sure to stop the interrupt URB before returning on errors during
open.

Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>

[ Upstream commit 030ee7ae ]

The modem-control signals are managed by the tty-layer during open and
should not be asserted prematurely when set_termios is called from
driver open.

Also make sure that the signals are asserted only when changing speed
from B0.

Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>