This commit fix kernel crash when probing for rfkill devices in dell-laptop
driver failed. Function free_page() was incorrectly used on struct page *
instead of virtual address of SMI buffer.

This commit also simplify allocating page for SMI buffer by using
__get_free_page() function instead of sequential call of functions
alloc_page() and page_address().
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This commit show additional information about rfkill state in debugfs based
on newly released documentation by Dell.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

Make sure that all existing SMBIOS calls for wireless control are properly
documented. This commit also add new documentation released by Dell.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

I haven't touched the code in a long time, and I don't have access to
the hardware anymore to test any changes to this driver.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This fixes a several year old regression that I found while trying
to get the Yoga 3 11 to work. The ideapad_rfk_set function is meant
to send a command to the embedded controller through ACPI, but
as of c1f73658, it sends the index of the rfkill device instead
of the command, and ignores the opcode field.

This changes it back to the original behavior, which indeed
flips the rfkill state as seen in the debugfs interface.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c1f73658 ("ideapad: pass ideapad_priv as argument (part 2)")
Cc: stable@vger.kernel.org # v2.6.38+
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

Until now module dell-laptop registered rfkill device which used i8042
filter function for receiving HW switch rfkill events (handling special
keycode).

But for some dell laptops there is native ACPI driver dell-rbtn which can
receive rfkill events (without i8042 hooks).

So this patch will combine best from both sides. It will use native ACPI
driver dell-rbtn for receiving events and dell-laptop SMBIOS interface for
enabling or disabling radio devices. If ACPI driver or device will not be
available fallback to i8042 filter function will be used.

Patch also changes module_init() to late_initcall() to ensure that init
function will be called after initializing dell-rbtn.c driver.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch exports notifier functions so other modules can receive HW
switch events. By default when some module register notifier, dell-rbtn
driver automatically remove rfkill interfaces from system (it is expected
that other module will use events for other rfkill interface). This
behaviour can be changed with new module parameter "auto_remove_rfkill".

This patch is designed for dell-laptop module for receiving those events.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
[dvhart@linux.intel.com: Cleanup MODULE_PARM_DESC formatting and grammar]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This is an ACPI driver for Dell laptops which receive HW slider radio
switch or hotkey toggle wifi button events. It exports rfkill device
dell-rbtn (which provide correct hard rfkill state) or hotkey input device.

Alex Hung is author of original hotkey input device code.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Cc: Alex Hung <alex.hung@canonical.com>
[fengguang.wu@intel.com: rbtn_ops can be static]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
[dvhart@linux.intel.com: Correct multi-line comment formatting]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

acpi_video_unregister() not only unregisters the acpi-video backlight
interface but also unregisters the acpi video bus event listener, causing
e.g. brightness hotkey presses to no longer generate keypress events.

The unregistering of the acpi video bus event listener usually is
undesirable, which by itself is a good reason to switch to
acpi_video_unregister_backlight().

Another problem with using acpi_video_unregister() rather then using
acpi_video_unregister_backlight() is that on systems with an intel video
opregion (most systems) and a broken_acpi_video quirk, whether or not
the acpi video bus event listener actually gets unregistered depends on
module load ordering:

Scenario a:
1) acpi/video.ko gets loaded (*), does not do acpi_video_register as there
   is an intel opregion.
2) intel.ko gets loaded, calls acpi_video_register() which registers both
   the listener and the acpi backlight interface
3) samsung-laptop.ko gets loaded, calls acpi_video_unregister() causing
   both the listener and the acpi backlight interface to unregister

Scenario b:
1) acpi/video.ko gets loaded (*), does not do acpi_video_register as there
   is an intel opregion.
2) samsung-laptop.ko gets loaded, calls acpi_video_dmi_promote_vendor(),
   calls acpi_video_unregister(), which is a nop since acpi_video_register
   has not yet been called
2) intel.ko gets loaded, calls acpi_video_register() which registers
   the listener, but does not register the acpi backlight interface due to
   the call to the preciding call to acpi_video_dmi_promote_vendor()

*) acpi/video.ko always loads first as both other modules depend on it.

So we end up with or without an acpi video bus event listener depending
on module load ordering, not good.

Switching to using acpi_video_unregister_backlight() means that independ
of ordering we will always have an acpi video bus event listener fixing
this.

Note that this commit means that systems without an intel video opregion,
and systems which were hitting scenario a wrt module load ordering, are
now getting an acpi video bus event listener while before they were not!

On some systems this may cause the brightness hotkeys to start generating
keypresses while before they were not (good), while on other systems this
may cause the brightness hotkeys to generate multiple keypress events for
a single press (not so good). Since on most systems the acpi video bus is
the canonical source for brightness events I believe that the latter case
will needs to be handled on a case by case basis by filtering out the
duplicate keypresses at the other source for them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Corentin Chary <corentin.chary@gmail.com)
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

acpi_video_unregister() not only unregisters the acpi-video backlight
interface but also unregisters the acpi video bus event listener, causing
e.g. brightness hotkey presses to no longer generate keypress events.

The unregistering of the acpi video bus event listener usually is
undesirable, which by itself is a good reason to switch to
acpi_video_unregister_backlight().

Another problem with using acpi_video_unregister() rather then using
acpi_video_unregister_backlight() is that on systems with an intel video
opregion (most systems) and a wmi_backlight_power quirk, whether or not
the acpi video bus event listener actually gets unregistered depends on
module load ordering:

Scenario a:
1) acpi/video.ko gets loaded (*), does not do acpi_video_register as there
   is an intel opregion.
2) intel.ko gets loaded, calls acpi_video_register() which registers both
   the listener and the acpi backlight interface
3) asus-wmi.ko gets loaded, calls acpi_video_unregister() causing both
   the listener and the acpi backlight interface to unregister

Scenario b:
1) acpi/video.ko gets loaded (*), does not do acpi_video_register as there
   is an intel opregion.
2) asus-wmi.ko gets loaded, calls acpi_video_dmi_promote_vendor(),
   calls acpi_video_unregister(), which is a nop since acpi_video_register
   has not yet been called
2) intel.ko gets loaded, calls acpi_video_register() which registers
   the listener, but does not register the acpi backlight interface due to
   the call to the preciding call to acpi_video_dmi_promote_vendor()

*) acpi/video.ko always loads first as both other modules depend on it.

So we end up with or without an acpi video bus event listener depending
on module load ordering, not good.

Switching to using acpi_video_unregister_backlight() means that independ
of ordering we will always have an acpi video bus event listener fixing
this.

Note that this commit means that systems without an intel video opregion,
and systems which were hitting scenario a wrt module load ordering, are
now getting an acpi video bus event listener while before they were not!

On some systems this may cause the brightness hotkeys to start generating
keypresses while before they were not (good), while on other systems this
may cause the brightness hotkeys to generate multiple keypress events for
a single press (not so good). Since on most systems the acpi video bus is
the canonical source for brightness events I believe that the latter case
will needs to be handled on a case by case basis by filtering out the
duplicate keypresses at the other source for them.

Cc: acpi4asus-user@lists.sourceforge.net
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Corentin Chary <corentin.chary@gmail.com)
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

acpi_video_unregister() not only unregisters the acpi-video backlight
interface but also unregisters the acpi video bus event listener, causing
e.g. brightness hotkey presses to no longer generate keypress events.

The unregistering of the acpi video bus event listener usually is
undesirable, which by itself is a good reason to switch to
acpi_video_unregister_backlight().

Another problem with using acpi_video_unregister() rather then using
acpi_video_unregister_backlight() is that on systems with an intel video
opregion (most systems) whether or not the acpi video bus event listener
actually gets unregistered depends on module load ordering:

Scenario a:
1) acpi/video.ko gets loaded (*), does not do acpi_video_register as there
   is an intel opregion.
2) intel.ko gets loaded, calls acpi_video_register() which registers both
   the listener and the acpi backlight interface
3) apple-gmux.ko gets loaded, calls acpi_video_unregister() causing both
   the listener and the acpi backlight interface to unregister

Scenario b:
1) acpi/video.ko gets loaded (*), does not do acpi_video_register as there
   is an intel opregion.
2) apple-gmux.ko gets loaded, calls acpi_video_dmi_promote_vendor(),
   calls acpi_video_unregister(), which is a nop since acpi_video_register
   has not yet been called
2) intel.ko gets loaded, calls acpi_video_register() which registers
   the listener, but does not register the acpi backlight interface due to
   the call to the preciding call to acpi_video_dmi_promote_vendor()

*) acpi/video.ko always loads first as both other modules depend on it.

So we end up with or without an acpi video bus event listener depending
on module load ordering, not good.

Switching to using acpi_video_unregister_backlight() means that independ
of ordering we will always have an acpi video bus event listener fixing
this.

Note that this commit means that systems without an intel video opregion,
and systems which were hitting scenario a wrt module load ordering, are
now getting an acpi video bus event listener while before they were not!

On some systems this may cause the brightness hotkeys to start generating
keypresses while before they were not (good), while on other systems this
may cause the brightness hotkeys to generate multiple keypress events for
a single press (not so good). Since on most systems the acpi video bus is
the canonical source for brightness events I believe that the latter case
will needs to be handled on a case by case basis by filtering out the
duplicate keypresses at the other source for them.

Cc: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

pvpanic was not properly detected when _STA was missing.

ACPI 6.0 April 2015, 6.3.7 _STA (Status)
  If a device object (including the processor object) does not have an
  _STA object, then OSPM assumes that all of the above bits are set
  (i.e., the device is present, enabled, shown in the UI, and
  functioning).

Not adhering to the specification made pvpanic dormant under QEMU 2.3.

The original patch used acpi_bus_get_status_handle, which was not
being exported, so module build blew up;  switch to acpi_bus_get_status
and use the status it populates.

Populated status is a bitfield so we can make the code self-documenting.
We do not check 'present' because 'enabled' has to be false in that case
by specification.  Older QEMUs set 0xff to status and newer ones do 0xb.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
[dvhart@linux.intel.com: Merge acpi_bug_get_status fix to avoid bisect breakage]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

Lenovo G30-50 does not have a hardware wireless switch and wireless
is always blocked.

BugLink: https://bugs.launchpad.net/bugs/1397021Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Philippe Coval <philippe.coval@open.eurogiciel.org>
[dvhart@linux.intel.com: Reordered dmi id per Phillippe's later version]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch is partially based on Felipe Contrera's earlier patch, that
was discussed here: https://lkml.org/lkml/2013/10/8/800
Some problems of that patch are solved, now:

1) The main obstacle for the earlier patch seemed to be the use of
virt_to_phys, which is accepted, now

2) random memory corruption occurred on my notebook, thus DMA-able memory
is allocated now, which solves this problem

3) hwmon interface is used instead of the thermal interface, as a
hwmon device is already set up by this driver and seemed more
appropriate than the thermal interface

4) Calling the ACPI-functions was modularized thus it's possible to call
some multifunctions easily, now (by using
asus_wmi_evaluate_method_agfn).

Unfortunately the WMI doesn't support controlling both fans on
a dual-fan notebook because of an restriction in the acpi-method
"SFNS", that is callable through the wmi. If "SFNV" would be called
directly even dual fan configurations could be controlled, but not by using
wmi.

Speed readings only work on auto-mode, thus "-1" will be reported in
manual mode.
Additionally the speed readings are reported as hundreds of RPM thus
they are not too precise.

This patch is tested only on one notebook (N551JK) but a similar module,
that contained some code to try to control the second fan also, was
reported to work on an UX32VD, at least for the first fan.

As Felipe already mentioned the low-level functions are described here:
http://forum.notebookreview.com/threads/fan-control-on-asus-prime-ux31-ux31a-ux32a-ux32vd.705656/Signed-off-by: Kast Bernd <kastbernd@gmx.de>
Acked-by: Corentin Chary <corentin.chary@gmail.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch adds a new file describing the sysfs entries for the
toshiba_haps driver.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch makes use of DEVICE_ATTR_{RW, WO} macros, simplifying
device attributes creation.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch simply replaces the use of sscanf with kstrtoint returning
the error code in case that something went bad.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch simply bumps the driver version to 0.22, as significant
changes were made to the driver, such as cleanups, updated events,
keymap handling, fixes and the bluetooth rfkill code removal.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch removes the check for TOS_FAILURE whenever we are using
the tci_raw function call, as that code is only returned by the
{hci, sci}_{read, write} functions and never by the tci_raw, and
thus making that check irrelevant.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch simply does some misc cleanup to comments, mainly
capitalizes some left over comments from a previous clean up and
adds some comments at the beginning of some feature function calls,
as well as some misc changes to some comments.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch simply renames the hci_{read, write}1 functions to
hci_{read, write}.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch removes the hci_{read, write}2 functions from the driver,
and the toshiba_hotkey_event_type_get function was adapted to use the
tci_raw function.

The hci_write2 function was only used by the bluetooth rfkill code,
but since its removal, it was causing build warnings, and the
hci_read2 function was only used by the toshiba_hotkey_event_type_get
function.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

The function toshiba_bluetooth_status is currently printing the
status of the device whenever it is queried, but since the
introduction of the rfkill poll code, this value will get printed
everytime the poll occurs.

This patch removes the status message from the *_status function, and
adds a debug message to the *_sync_status function printing the
bluetooth device raw status, killswitch, plug and power states of the
device as well.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch adapts toshiba_bluetooth_enable, toshiba_bt_rfkill_notify
and toshiba_bt_resume functions to rfkill.

The *_enable function was cleaned from code that the rfkill code now
provides, and the other two functions were modified to update the rfkill
switch status, as they were only calling toshiba_bluetooth_enable.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch adds RFKill handler functions to the driver, allowing it
to register and update the rfkill switch status.

Also, a comment block was moved from the header to the poll function,
as it explains why we need to poll the killswitch on older devices.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch adds a struct named toshiba_bluetooth_dev, which will be
used to contain the acpi_device struct and bluetooth status booleans.

This struct will also be used by later patches to store the rfkill
struct as well.

Also, a helper function named toshiba_bluetooth_sync_status was added
to be also used by upcomming patches.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

This patch removes all bluetooth rfkill related code residing in
the toshiba_acpi driver.

Separate patches will add (and adapt) the code to toshiba_bluetooth
(where it belongs).
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>

AMD CPUs don't reinitialize the SS descriptor on SYSRET, so SYSRET with
SS == 0 results in an invalid usermode state in which SS is apparently
equal to __USER_DS but causes #SS if used.

Work around the issue by setting SS to __KERNEL_DS __switch_to, thus
ensuring that SYSRET never happens with SS set to NULL.

This was exposed by a recent vDSO cleanup.

Fixes: e7d6eefa x86/vdso32/syscall.S: Do not load __USER32_DS to %ss
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull intel drm fixes from Dave Airlie.

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: vlv: fix save/restore of GFX_MAX_REQ_COUNT reg
  drm/i915: Workaround to avoid lite restore with HEAD==TAIL
  drm/i915: cope with large i2c transfers

Pull intel iommu updates from David Woodhouse:
 "This lays a little of the groundwork for upcoming Shared Virtual
  Memory support — fixing some bogus #defines for capability bits and
  adding the new ones, and starting to use the new wider page tables
  where we can, in anticipation of actually filling in the new fields
  therein.

  It also allows graphics devices to be assigned to VM guests again.
  This got broken in 3.17 by disallowing assignment of RMRR-afflicted
  devices.  Like USB, we do understand why there's an RMRR for graphics
  devices — and unlike USB, it's actually sane.  So we can make an
  exception for graphics devices, just as we do USB controllers.

  Finally, tone down the warning about the X2APIC_OPT_OUT bit, due to
  persistent requests.  X2APIC_OPT_OUT was added to the spec as a nasty
  hack to allow broken BIOSes to forbid us from using X2APIC when they
  do stupid and invasive things and would break if we did.

  Someone noticed that since Windows doesn't have full IOMMU support for
  DMA protection, setting the X2APIC_OPT_OUT bit made Windows avoid
  initialising the IOMMU on the graphics unit altogether.

  This means that it would be available for use in "driver mode", where
  the IOMMU registers are made available through a BAR of the graphics
  device and the graphics driver can do SVM all for itself.

  So they started setting the X2APIC_OPT_OUT bit on *all* platforms with
  SVM capabilities.  And even the platforms which *might*, if the
  planets had been aligned correctly, possibly have had SVM capability
  but which in practice actually don't"

* git://git.infradead.org/intel-iommu:
  iommu/vt-d: support extended root and context entries
  iommu/vt-d: Add new extended capabilities from v2.3 VT-d specification
  iommu/vt-d: Allow RMRR on graphics devices too
  iommu/vt-d: Print x2apic opt out info instead of printing a warning
  iommu/vt-d: kill bogus ecap_niotlb_iunits()

Pull i2c fixes from Wolfram Sang:
 "This has a mixture of merge window cleanups and bugfixes"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: st: add include for pinctrl
  i2c: mux: use proper dev when removing "channel-X" symlinks
  i2c: digicolor: remove duplicate include
  i2c: Mark adapter devices with pm_runtime_no_callbacks
  i2c: pca-platform: fix broken email address
  i2c: mxs: fix broken email address
  i2c: rk3x: report number of messages transmitted

Pull btrfs fixes from Chris Mason:
 "Filipe hit two problems in my block group cache patches.  We finalized
  the fixes last week and ran through more tests"

* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: prevent list corruption during free space cache processing
  Btrfs: fix inode cache writeout

Merge tag 'drm-intel-next-fixes-2015-04-25' of git://anongit.freedesktop.org/drm-intel into drm-fixes

three fixes for i915.

* tag 'drm-intel-next-fixes-2015-04-25' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: vlv: fix save/restore of GFX_MAX_REQ_COUNT reg
  drm/i915: Workaround to avoid lite restore with HEAD==TAIL
  drm/i915: cope with large i2c transfers

Pull NFS client updates from Trond Myklebust:
 "Another set of mainly bugfixes and a couple of cleanups.  No new
  functionality in this round.

  Highlights include:

  Stable patches:
   - Fix a regression in /proc/self/mountstats
   - Fix the pNFS flexfiles O_DIRECT support
   - Fix high load average due to callback thread sleeping

  Bugfixes:
   - Various patches to fix the pNFS layoutcommit support
   - Do not cache pNFS deviceids unless server notifications are enabled
   - Fix a SUNRPC transport reconnection regression
   - make debugfs file creation failure non-fatal in SUNRPC
   - Another fix for circular directory warnings on NFSv4 "junctioned"
     mountpoints
   - Fix locking around NFSv4.2 fallocate() support
   - Truncating NFSv4 file opens should also sync O_DIRECT writes
   - Prevent infinite loop in rpcrdma_ep_create()

  Features:
   - Various improvements to the RDMA transport code's handling of
     memory registration
   - Various code cleanups"

* tag 'nfs-for-4.1-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (55 commits)
  fs/nfs: fix new compiler warning about boolean in switch
  nfs: Remove unneeded casts in nfs
  NFS: Don't attempt to decode missing directory entries
  Revert "nfs: replace nfs_add_stats with nfs_inc_stats when add one"
  NFS: Rename idmap.c to nfs4idmap.c
  NFS: Move nfs_idmap.h into fs/nfs/
  NFS: Remove CONFIG_NFS_V4 checks from nfs_idmap.h
  NFS: Add a stub for GETDEVICELIST
  nfs: remove WARN_ON_ONCE from nfs_direct_good_bytes
  nfs: fix DIO good bytes calculation
  nfs: Fetch MOUNTED_ON_FILEID when updating an inode
  sunrpc: make debugfs file creation failure non-fatal
  nfs: fix high load average due to callback thread sleeping
  NFS: Reduce time spent holding the i_mutex during fallocate()
  NFS: Don't zap caches on fallocate()
  xprtrdma: Make rpcrdma_{un}map_one() into inline functions
  xprtrdma: Handle non-SEND completions via a callout
  xprtrdma: Add "open" memreg op
  xprtrdma: Add "destroy MRs" memreg op
  xprtrdma: Add "reset MRs" memreg op
  ...

Pull fourth vfs update from Al Viro:
 "d_inode() annotations from David Howells (sat in for-next since before
  the beginning of merge window) + four assorted fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  RCU pathwalk breakage when running into a symlink overmounting something
  fix I_DIO_WAKEUP definition
  direct-io: only inc/dec inode->i_dio_count for file systems
  fs/9p: fix readdir()
  VFS: assorted d_backing_inode() annotations
  VFS: fs/inode.c helpers: d_inode() annotations
  VFS: fs/cachefiles: d_backing_inode() annotations
  VFS: fs library helpers: d_inode() annotations
  VFS: assorted weird filesystems: d_inode() annotations
  VFS: normal filesystems (and lustre): d_inode() annotations
  VFS: security/: d_inode() annotations
  VFS: security/: d_backing_inode() annotations
  VFS: net/: d_inode() annotations
  VFS: net/unix: d_backing_inode() annotations
  VFS: kernel/: d_inode() annotations
  VFS: audit: d_backing_inode() annotations
  VFS: Fix up some ->d_inode accesses in the chelsio driver
  VFS: Cachefiles should perform fs modifications on the top layer only
  VFS: AF_UNIX sockets should call mknod on the top layer only

Pull more power management and ACPI updates from Rafael Wysocki:
 "These are fixes mostly (intel_pstate, ACPI core, ACPI EC driver,
  cpupower tool), a new CPU ID for the Intel RAPL driver and one
  intel_pstate driver improvement that didn't make it to my previous
  pull requests due to timing.

  Specifics:

   - Fix a build warning in the intel_pstate driver showing up in
     non-SMP builds (Borislav Petkov)

   - Change one of the intel_pstate's P-state selection parameters for
     Baytrail and Cherrytrail CPUs to significantly improve performance
     at the cost of a small increase in energy consumption (Kristen
     Carlson Accardi)

   - Fix a NULL pointer dereference in the ACPI EC driver due to an
     unsafe list walk in the query handler removal routine (Chris
     Bainbridge)

   - Get rid of a false-positive lockdep warning in the ACPI container
     hot-remove code (Rafael J Wysocki)

   - Prevent the ACPI device enumeration code from creating device
     objects of a wrong type in some cases (Rafael J Wysocki)

   - Add Skylake processors support to the Intel RAPL power capping
     driver (Brian Bian)

   - Drop the stale MAINTAINERS entry for the ACPI dock driver that is
     regarded as part of the ACPI core and maintained along with it now
     (Chao Yu)

   - Fix cpupower tool breakage caused by a library API change in libpci
     3.3.0 (Lucas Stach)"

* tag 'pm+acpi-4.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / scan: Add a scan handler for PRP0001
  ACPI / scan: Annotate physical_node_lock in acpi_scan_is_offline()
  ACPI / EC: fix NULL pointer dereference in acpi_ec_remove_query_handler()
  MAINTAINERS: remove maintainship entry of docking station driver
  powercap / RAPL: Add support for Intel Skylake processors
  cpufreq: intel_pstate: Fix an annoying !CONFIG_SMP warning
  intel_pstate: Change the setpoint for Atom params
  cpupower: fix breakage from libpci API change

Pull crypto fixes from Herbert Xu:
 "This push fixes a build problem with img-hash under non-standard
  configurations and a serious regression with sha512_ssse3 which can
  lead to boot failures"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: img-hash - CRYPTO_DEV_IMGTEC_HASH should depend on HAS_DMA
  crypto: x86/sha512_ssse3 - fixup for asm function prototype change

Merge tag 'platform-drivers-x86-v4.1-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull x86 platform driver updates from Darren Hart:
 "This series includes significant updates to the toshiba_acpi driver
  and the reintroduction of the dell-laptop keyboard backlight additions
  I had to revert previously.  Also included are various fixes for
  typos, warnings, correctness, and minor bugs.

  Specifics:

  dell-laptop:
     - add support for keyboard backlight.

  toshiba_acpi:
     - adaptive keyboard, hotkey, USB sleep and charge, and backlight
       updates.  Update sysfs documentation.

  toshiba_bluetooth:
     - fix enabling/disabling loop on recent devices

  apple-gmux:
     - lock iGP IO to protect from vgaarb changes

  other:
     - Fix typos, clear gcc warnings, clarify pr_* messages, correct
       return types, update MAINTAINERS"

* tag 'platform-drivers-x86-v4.1-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (25 commits)
  toshiba_acpi: Do not register vendor backlight when acpi_video bl is available
  MAINTAINERS: Add me on list of Dell laptop drivers
  platform: x86: dell-laptop: Add support for keyboard backlight
  Documentation/ABI: Update sysfs-driver-toshiba_acpi entry
  toshiba_acpi: Fix pr_* messages from USB Sleep Functions
  toshiba_acpi: Update and fix USB Sleep and Charge modes
  wmi: Use bool function return values of true/false not 1/0
  toshiba_bluetooth: Fix enabling/disabling loop on recent devices
  toshiba_bluetooth: Clean up *_add function and disable BT device at removal
  toshiba_bluetooth: Add three new functions to the driver
  toshiba_acpi: Fix the enabling of the Special Functions
  toshiba_acpi: Use the Hotkey Event Type function for keymap choosing
  toshiba_acpi: Add Hotkey Event Type function and definitions
  x86/wmi: delete unused wmi_data_lock mutex causing gcc warning
  apple-gmux: lock iGP IO to protect from vgaarb changes
  MAINTAINERS: Add missing Toshiba devices and add myself as maintainer
  toshiba_acpi: Update events in toshiba_acpi_notify
  intel-oaktrail: Fix trivial typo in comment
  thinkpad_acpi: off by one in adaptive_keyboard_hotkey_notify_hotkey()
  thinkpad_acpi: signedness bugs getting current_mode
  ...

Pull chrome platform updates from Olof Johansson:
 "Here's a set of updates to the Chrome OS platform drivers for this
  merge window.

  Main new things this cycle is:

   - Driver changes to expose the lightbar to users.  With this, you can
     make your own blinkenlights on Chromebook Pixels.

   - Changes in the way that the atmel_mxt trackpads are probed.  The
     laptop driver is trying to be smart and not instantiate the devices
     that don't answer to probe.  For the trackpad that can come up in
     two modes (bootloader or regular), this gets complicated since the
     driver already knows how to handle the two modes including the
     actual addresses used.  So now the laptop driver needs to know more
     too, instantiating the regular address even if the bootloader one
     is the probe that passed.

   - mfd driver improvements by Javier Martines Canillas, and a few
     bugfixes from him, kbuild and myself"

* tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
  platform/chrome: chromeos_laptop - instantiate Atmel at primary address
  platform/chrome: cros_ec_lpc - Depend on X86 || COMPILE_TEST
  platform/chrome: cros_ec_lpc - Include linux/io.h header file
  platform/chrome: fix platform_no_drv_owner.cocci warnings
  platform/chrome: cros_ec_lightbar - fix duplicate const warning
  platform/chrome: cros_ec_dev - fix Unknown escape '%' warning
  platform/chrome: Expose Chrome OS Lightbar to users
  platform/chrome: Create sysfs attributes for the ChromeOS EC
  mfd: cros_ec: Instantiate ChromeOS EC character device
  platform/chrome: Add Chrome OS EC userspace device interface
  platform/chrome: Add cros_ec_lpc driver for x86 devices
  mfd: cros_ec: Add char dev and virtual dev pointers
  mfd: cros_ec: Use fixed size arrays to transfer data with the EC