Merge tag 'omap-for-v3.13/fixes-against-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

From Tony Lindgren:

Some omap related fixes that have come up with people moving to device
tree only based booting for omap2+.

The series contains a handful of fixes for the igep boards as they were
one of the first omap3 boards to jump over completely to device tree
based booting. So these can be considered regressions compared to
booting igep in legacy mode with board files in v3.12.

Also included are few other device tree vs legacy booting regressions:

- yet more missing omap3 .dtsi entries that have showed up booting
  various boards with device tree only

- n900 eMMC device tree fix

- fixes for beagle USB EHCI

- two fixes to make omap2420 MMC work

As we're moving omap2+ to be device tree only for v3.14, I'd like to
have v3.13 work equally well for legacy based booting and device tree
based booting. So there will be likely few more device tree related
booting patches trickling in.

This series also includes a regression fix for the omap timer posted
mode that may wrongly stay on from the bootloader for some SoCs.

* tag 'omap-for-v3.13/fixes-against-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  mmc: omap: Fix I2C dependency and make driver usable with device tree
  mmc: omap: Fix DMA configuration to not rely on device id
  ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
  ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
  ARM: dts: AM33XX IGEP0033: add USB support
  ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
  ARM: dts: AM33XX BASE0033: add pinmux and user led support
  ARM: dts: AM33XX BASE0033: add pinmux and hdmi node to enable display
  ARM: dts: omap3-igep0020: Add pinmuxing for DVI output
  ARM: dts: omap3-igep0020: Add pinmux setup for i2c devices
  ARM: dts: omap3-igep: Update to use the TI AM/DM37x processor
  ARM: dts: omap3-igep: Add support for LBEE1USJYC WiFi connected to SDIO
  ARM: dts: omap3-igep: Fix bus-width for mmc1
  ARM: OMAP2+: dss-common: change IGEP's DVI DDC i2c bus
  ARM: OMAP2+: Disable POSTED mode for errata i103 and i767
  ARM: OMAP2+: Fix eMMC on n900 with device tree
  ARM: OMAP2+: Add fixed regulator to omap2plus_defconfig
  ARM: OMAP2+: Fix more missing data for omap3.dtsi file
Signed-off-by: Olof Johansson <olof@lixom.net>

Some features can be configured by the companion I2C chips,
which may not be available at the probe time. Fix the issue
by returning -EPROBE_DEFER when the MMC controller slots
are not configured.

While at it, let's also add minimal device tree support so
omap24xx platforms can use this driver without legacy mode
since we claim to support device tree for mach-omap2 based
systems.

Although adding the minimal device tree support is not strictly
a fix, it does remove one of the last blockers for dropping a
bunch of legacy platform data for mach-omap2.

Cc: linux-mmc@vger.kernel.org
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We are wrongly relying on device id for the DMA configuration
which can lead to wrong DMA channel being selected.

Fix the issue by using the standard resources like we should.

Cc: linux-mmc@vger.kernel.org
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Beagle (rev. C4) and Beagle-XM (all revs) need VAUX2 1.8V supply
for the USB PHY.

As the generic PHY driver can't handle more than one supply
at the moment, we configure this supply to be always on.
This will cause a very small power impact if the USB host subsystem
is not in use, about 76.86 micro-W + LDO power.

Older Beagle boards (prior to C4) don't have VAUX2 connected anywhere,
so there won't be any functional impact on those boards other than
some additional LDO power consumption.
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On Device Tree boot the VDDS_DSI regulator is not linked to
the DPI device so omapfb driver probing fails with:

[    3.186035] OMAPFB: omapfb_probe
[    3.190704] omapdss DPI error: can't get VDDS_DSI regulator
[    3.196594] omapfb omapfb: failed to connect default display
[    3.202667] omapfb omapfb: failed to init overlay connections
[    3.208892] OMAPFB: free_resources
[    3.212493] OMAPFB: free all fbmem
[    3.216735] omapfb omapfb: failed to setup omapfb

As a workaround name the VPLL2 regulator from twl4030 as vdds_dsi
so getting the VDDS_DSI regulator will succeed on dpi_init_regulator().
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add node to support the USB Host and the USB OTG on the IGEP AQUILA
Processor Board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The IGEP AQUILA EXPANSION has a 32KBit EEPROM for user data storage.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable the user leds on the IGEP AQUILA EXPANSION. The has two leds,
one green and one red, that are controllable by software.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable the hdmi output and the LCD Controller on IGEP AQUILA. Also
configure the correct pinmux for output of video data from the SoC
to the HDMI encoder.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The IGEPv2 has a TFP410 DPI-to-DVI encoder attached to OMAP's
Display SubSystem (DSS).

Add mux setup for DSS pins and also for the GPIO 170 pin that
is used to ensure that the DVI-D is powered down on power up.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add pin muxing support for IGEP boards i2c controllers.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Most of the boards are using the TI AM/DM37x processor, there is only a small
quantity of IGEP Processor Boards based on TI OMAP3530. So it's better use the
omap36xx.dtsi include instead of omap34xx.dtsi include. We can add support
for the 34xx based variant later on as needed.

To avoid confusion we have added to the model the (TI AM/DM37x) comment.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[tony@atomide.com: updated comments for the 34xx to 36xx include change]
Signed-off-by: Tony Lindgren <tony@atomide.com>

The LBEE1USJYC is a WiFi/BT combo module used on OMAP3-based IGEP boards. In
both cases, IGEPv2 Rev. C and IGEP COM MODULE, the module is connected using
the same MMC interface and uses the same GPIOs.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Both, IGEPv2 and IGEP COM MODULE have a bus-width of 4 not 8, so fix this and
do not mux data pins from mmc1_data4 to mmc1_data7.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

IGEP's DVI connector's DDC pins are connected to OMAP's third i2c bus.

When booting with Device Trees the requested bus number is set to -1
which means that the bus number should be dynamically assigned. So the
third i2c bus has 2 has a bus number.

Since now only DT booting is supported for IGEP boards after commit
06ff74fd ("ARM: OMAP2+: remove legacy support for IGEP boards"), the
i2c bus number has to be changed.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enabling of Posted mode is seen to cause problems on dmtimer modules on AM33xx
(much like other OMAPs).  Reference discussions on forums [1] [2]. Earlier
patch solving this on other OMAPs [3].

For OMAP SoCs with this errata, the fix has been to not enable Posted mode.
However, on some SoCs (atleast AM33xx) which carry this errata, Posted mode
is enabled on reset. So we not only need to ignore enabling of the POSTED bit
when the timer is requested, but also disable Posted mode if errata is present.

[1] http://e2e.ti.com/support/arm/sitara_arm/f/791/t/285744.aspx
[2] http://e2e.ti.com/support/arm/sitara_arm/f/791/t/270632.aspx
[3] http://www.spinics.net/lists/linux-omap/msg81770.html

Cc: stable@vgerk.kernel.org
Reported-by: Russ Dill <russ.dill@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge tag 'ux500-defconfig-v3.13-rcs' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes

From Linus Walleij, Ux500 defconfig patches for the v3.13 rc series:

- Allow creation and mounting of devtmpfs, which is used
  by OpenEmbedded root filesystems among others.

- Enable CPUidle for the ux500, it has been accidentally
  disabled due to a Kconfig change.

* tag 'ux500-defconfig-v3.13-rcs' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ARM: ux500: u8500_defconfig: add missing cpuidle option
  u8500_defconfig: allow creation and mounting of devtmpfs

Merge tag 'ux500-fixes-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes

From Linus Walleij, Ux500 fixes for the v3.13 series:

- Restore platform data for the (e)MMC/SD controllers, so they can
  pins and special flags properly like before.

* tag 'ux500-fixes-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  Revert "ARM: ux500: Stop passing MMC's platform data for Device Tree boots"
  Revert "ARM: ux500: Remove AUXDATA relating to SDI (MMC) clock-name bindings"

This reverts commit 49c12951.

The special settings for the SD/MMC card parameters that are not
yet fully agreed upon how to encode into the device tree went missing
with this commit. We need to first put it into the device tree,
and then remove the platform data.

Cc: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This reverts commit ce16feb8.

This commit stopped tying down the name of the MMC/SD devices, but these
names are used in the pin control table, so the MMC/SD cards stopped
working.

Cc: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

With the commit d3f2950f, the option
ARM_U8500_CPUIDLE was added to the Kconfig but not reflected in the
default config file, hence the cpuidle driver is no longer enabled
since this commit.

Enable it again by adding the missing option in the default config file.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch enables CONFIG_DETTMPFS and CONFIG_DEVTMPFS_MOUNT
flags for u8500 based devices.

In this way it's possible to create a tmpfs/ramfs already in the
early stages of the boot, allowing programs like udev/mdev to
populate the /dev directory.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The I2C controller node needs #address-cells and #size-cells properties,
but these are currently missing. Add them. This allows child nodes to be
parsed correctly.

Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

The imx fixes for 3.13, part 2:
 - Disable S/PDIF "rxtx5" clock option to fix the clocksource breakage
   introduced by S/PDIF driver

* tag 'imx-fixes-3.13-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: dts: imx6qdl: disable spdif "rxtx5" clock option
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Without the interrupt you'll get problems if you enable
CONFIG_RTC_DRV_MAX77686.  Setup the interrupt properly in the device
tree.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org

Looks like we need to configure the regulators and use the pdata
quirk to make eMMC work with device tree.

It seems that mostly vaux3 is used, and only some earlier revisions
used vmmc2. This has been tested to work on devices where the
system_rev passed by the bootloader has versions 0x0010, 0x2101
and 0x2204.

Cc: devicetree@vger.kernel.org
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@debian.org>
[tony@atomide.com: updated with pinctrl changes and comments from Sebastian]
Signed-off-by: Tony Lindgren <tony@atomide.com>

We do not have REGULATOR_FIXED selected if no boards are selected
and we boot with device tree. This can cause various devices to
fail.
Signed-off-by: Tony Lindgren <tony@atomide.com>

After dropping the duplicate data in hwmod that now should come from
the .dts files, I noticed few more entries missing. Let's add these
as otherwise devices relying on these won't work.

Looks like the side tone entries are bundled into the mcbsp1 to 3,
so that may needs some special handling in the hwmod code as it's
currently trying to look up mcbsp2_sidetone and mcbsp3_sidetone
entries.
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch implements the power_down_finish() method for TC2, to
enable the kernel to confirm when CPUs are safely powered down.

The information required for determining when a CPU is parked
cannot be obtained from any single place, so a few sources of
information must be combined:

  * mcpm_cpu_power_down() must be pending for the CPU, so that we
    don't get confused by false STANDBYWFI positives arising from
    CPUidle.  This is detected by waiting for the tc2_pm use count
    for the target CPU to reach 0.

  * Either the SPC must report that the CPU has asserted
    STANDBYWFI, or the TC2 tile's reset control logic must be
    holding the CPU in reset.

    Just checking for STANDBYWFI is not sufficient, because this
    signal is not latched when the the cluster is clamped off and
    powered down: the relevant status bits just drop to zero.  This
    means that STANDBYWFI status cannot be used for reliable
    detection of the last CPU in a cluster reaching WFI.

This patch is required in order for kexec to work with MCPM on TC2.

MCPM code was changed in commit 0de0d646 ('ARM: 7848/1: mcpm:
Implement cpu_kill() to synchronise on powerdown'), and since then it
will hit a WARN_ON_ONCE() due to power_down_finish not being implemented
on the TC2 platform.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

In order to support increased build test coverage for drivers, implement
dummies for the powergate implementation. This will allow the drivers to
be built without requiring support for Tegra to be selected.

This patch solves the following build errors, which can be triggered in
v3.13-rc1 by selecting DRM_TEGRA without ARCH_TEGRA:

drivers/built-in.o: In function `gr3d_remove':
drivers/gpu/drm/tegra/gr3d.c:321: undefined reference to `tegra_powergate_power_off'
drivers/gpu/drm/tegra/gr3d.c:325: undefined reference to `tegra_powergate_power_off'
drivers/built-in.o: In function `gr3d_probe':
drivers/gpu/drm/tegra/gr3d.c:266: undefined reference to `tegra_powergate_sequence_power_up'
drivers/gpu/drm/tegra/gr3d.c:273: undefined reference to `tegra_powergate_sequence_power_up'
Signed-off-by: Thierry Reding <treding@nvidia.com>
[swarren, updated commit description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.

* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
  ARM: OMAP2+: Remove legacy mux code for display.c
  ARM: OMAP2+: Fix undefined reference to set_cntfreq
  gpio: twl4030: Fix passing of pdata in the device tree case
  gpio: twl4030: Fix regression for twl gpio output
  ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
  ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
  ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
  i2c: omap: Fix missing device tree flags for omap2

Some omap3 code is throwing a warning:
arch/arm/mach-omap2/pm34xx.c: In function 'omap3_save_secure_ram_context':
arch/arm/mach-omap2/pm34xx.c:123:32: warning: cast to pointer from
  integer of different size [-Wint-to-pointer-cast]

In reality this code will never actually execute with LPAE=y, since
Cortex-A8 doesn't support it. So downcasting the __pa() is safe in
this case.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Tony Lindgren <tony@atomide.com>

Merge tag 'ecryptfs-3.13-rc1-quiet-checkers' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull minor eCryptfs fix from Tyler Hicks:
 "Quiet static checkers by removing unneeded conditionals"

* tag 'ecryptfs-3.13-rc1-quiet-checkers' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: file->private_data is always valid

Pull second set of sound fixes from Takashi Iwai:
 "A collection of small fixes in HD-audio quirks and runtime PM, ASoC
  rcar, abs8500 and other codecs.  Most of commits are for stable
  kernels, too"

* tag 'sound-fix2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Set current_headset_type to ALC_HEADSET_TYPE_ENUM (janitorial)
  ALSA: hda - Provide missing pin configs for VAIO with ALC260
  ALSA: hda - Add headset quirk for Dell Inspiron 3135
  ALSA: hda - Fix the headphone jack detection on Sony VAIO TX
  ALSA: hda - Fix missing bass speaker on ASUS N550
  ALSA: hda - Fix unbalanced runtime PM notification at resume
  ASoC: arizona: Set FLL to free-run before disabling
  ALSA: hda - A casual Dell Headset quirk
  ASoC: rcar: fixup dma_async_issue_pending() timing
  ASoC: rcar: off by one in rsnd_scu_set_route()
  ASoC: wm5110: Add post SYSCLK register patch for rev D chip
  ASoC: ab8500: Revert to using custom I/O functions
  ALSA: hda - Also enable mute/micmute LED control for "Lenovo dock" fixup
  ALSA: firewire-lib: include sound/asound.h to refer to snd_pcm_format_t
  ALSA: hda - Select FW_LOADER from CONFIG_SND_HDA_CODEC_CA0132_DSP
  ALSA: hda - Enable mute/mic-mute LEDs for more Thinkpads with Realtek codec
  ASoC: rcar: fixup mod access before checking

Pull DRM fixes from Dave Airlie:
 "I was going to leave this until post -rc1 but sysfs fixes broke
  hotplug in userspace, so I had to fix it harder, otherwise a set of
  pulls from intel, radeon and vmware,

  The vmware/ttm changes are bit larger but since its early and they are
  unlikely to break anything else I put them in, it lets vmware work
  with dri3"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (36 commits)
  drm/sysfs: fix hotplug regression since lifetime changes
  drm/exynos: g2d: fix memory leak to userptr
  drm/i915: Fix gen3 self-refresh watermarks
  drm/ttm: Remove set_need_resched from the ttm fault handler
  drm/ttm: Don't move non-existing data
  drm/radeon: hook up backlight functions for CI and KV family.
  drm/i915: Replicate BIOS eDP bpp clamping hack for hsw
  drm/i915: Do not enable package C8 on unsupported hardware
  drm/i915: Hold pc8 lock around toggling pc8.gpu_idle
  drm/i915: encoder->get_config is no longer optional
  drm/i915/tv: add ->get_config callback
  drm/radeon/cik: Add macrotile mode array query
  drm/radeon/cik: Return backend map information to userspace
  drm/vmwgfx: Make vmwgfx dma buffers prime aware
  drm/vmwgfx: Make surfaces prime-aware
  drm/vmwgfx: Hook up the prime ioctls
  drm/ttm: Add a minimal prime implementation for ttm base objects
  drm/vmwgfx: Fix false lockdep warning
  drm/ttm: Allow execbuf util reserves without ticket
  drm/i915: restore the early forcewake cleanup
  ...

Pull PCI updates from Bjorn Helgaas:
 "Miscellaneous
   - Remove duplicate disable from pcie_portdrv_remove() (Yinghai Lu)
   - Fix whitespace, capitalization, and spelling errors (Bjorn Helgaas)"

* tag 'pci-v3.13-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Remove duplicate pci_disable_device() from pcie_portdrv_remove()
  PCI: Fix whitespace, capitalization, and spelling errors

Pull SCSI target updates from Nicholas Bellinger:
 "Things have been quiet this round with mostly bugfixes, percpu
  conversions, and other minor iscsi-target conformance testing changes.

  The highlights include:

   - Add demo_mode_discovery attribute for iscsi-target (Thomas)
   - Convert tcm_fc(FCoE) to use percpu-ida pre-allocation
   - Add send completion interrupt coalescing for ib_isert
   - Convert target-core to use percpu-refcounting for se_lun
   - Fix mutex_trylock usage bug in iscsit_increment_maxcmdsn
   - tcm_loop updates (Hannes)
   - target-core ALUA cleanups + prep for v3.14 SCSI Referrals support (Hannes)

  v3.14 is currently shaping to be a busy development cycle in target
  land, with initial support for T10 Referrals and T10 DIF currently on
  the roadmap"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits)
  iscsi-target: chap auth shouldn't match username with trailing garbage
  iscsi-target: fix extract_param to handle buffer length corner case
  iscsi-target: Expose default_erl as TPG attribute
  target_core_configfs: split up ALUA supported states
  target_core_alua: Make supported states configurable
  target_core_alua: Store supported ALUA states
  target_core_alua: Rename ALUA_ACCESS_STATE_OPTIMIZED
  target_core_alua: spellcheck
  target core: rename (ex,im)plict -> (ex,im)plicit
  percpu-refcount: Add percpu-refcount.o to obj-y
  iscsi-target: Do not reject non-immediate CmdSNs exceeding MaxCmdSN
  iscsi-target: Convert iscsi_session statistics to atomic_long_t
  target: Convert se_device statistics to atomic_long_t
  target: Fix delayed Task Aborted Status (TAS) handling bug
  iscsi-target: Reject unsupported multi PDU text command sequence
  ib_isert: Avoid duplicate iscsit_increment_maxcmdsn call
  iscsi-target: Fix mutex_trylock usage in iscsit_increment_maxcmdsn
  target: Core does not need blkdev.h
  target: Pass through I/O topology for block backstores
  iser-target: Avoid using FRMR for single dma entry requests
  ...

Pull hwmon fixes from Guenter Roeck:
 - acpi_power_meter: Fix return value check from call to
   acpi_bus_get_device
 - nct6775: Fix/improve NCT6791 support
 - lm75: Add support for GMT G751

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (acpi_power_meter) Fix acpi_bus_get_device() return value check
  hwmon: (nct6775) NCT6791 supports weight control only for CPUFAN
  hwmon: (nct6775) Monitor additional temperature registers
  hwmon: (lm75) Add support for GMT G751 chip

Pull networking fixes from David Miller:

 1) Fix memory leaks and other issues in mwifiex driver, from Amitkumar
    Karwar.

 2) skb_segment() can choke on packets using frag lists, fix from
    Herbert Xu with help from Eric Dumazet and others.

 3) IPv4 output cached route instantiation properly handles races
    involving two threads trying to install the same route, but we
    forgot to propagate this logic to input routes as well.  Fix from
    Alexei Starovoitov.

 4) Put protections in place to make sure that recvmsg() paths never
    accidently copy uninitialized memory back into userspace and also
    make sure that we never try to use more that sockaddr_storage for
    building the on-kernel-stack copy of a sockaddr.  Fixes from Hannes
    Frederic Sowa.

 5) R8152 driver transmit flow bug fixes from Hayes Wang.

 6) Fix some minor fallouts from genetlink changes, from Johannes Berg
    and Michael Opdenacker.

 7) AF_PACKET sendmsg path can race with netdevice unregister notifier,
    fix by using RCU to make sure the network device doesn't go away
    from under us.  Fix from Daniel Borkmann.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
  gso: handle new frag_list of frags GRO packets
  genetlink: fix genl_set_err() group ID
  genetlink: fix genlmsg_multicast() bug
  packet: fix use after free race in send path when dev is released
  xen-netback: stop the VIF thread before unbinding IRQs
  wimax: remove dead code
  net/phy: Add the autocross feature for forced links on VSC82x4
  net/phy: Add VSC8662 support
  net/phy: Add VSC8574 support
  net/phy: Add VSC8234 support
  net: add BUG_ON if kernel advertises msg_namelen > sizeof(struct sockaddr_storage)
  net: rework recvmsg handler msg_name and msg_namelen logic
  bridge: flush br's address entry in fdb when remove the
  net: core: Always propagate flag changes to interfaces
  ipv4: fix race in concurrent ip_route_input_slow()
  r8152: fix incorrect type in assignment
  r8152: support stopping/waking tx queue
  r8152: modify the tx flow
  r8152: fix tx/rx memory overflow
  netfilter: ebt_ip6: fix source and destination matching
  ...