- 25 May, 2018 40 commits
-
-
Daniel Mack authored
There's no need to disable the IRQ from inside its handler. Instead just grab the spinlock of the channel that is being processed. Signed-off-by:
Daniel Mack <daniel@zonque.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Daniel Mack authored
The device takes 32-bit addresses only, so inform the DMA API about it. This is the default on msm8016, so that doesn't change anything, but it's best practice to be explicit. Signed-off-by:
-
Daniel Mack authored
When wcn36xx_dxe_tx_frame() is entered while the device is still processing the queue asyncronously, we are racing against the firmware code with updates to the buffer descriptors. Presumably, the firmware scans the ring buffer that holds the descriptors and scans for a valid control descriptor, and then assumes that the next descriptor contains the payload. If, however, the control descriptor is marked valid, but the payload descriptor isn't, the packet is not sent out. Another issue with the current code is that is lacks memory barriers before descriptors are marked valid. This is important because the CPU may reorder writes to memory, even if it is allocated as coherent DMA area, and hence the device may see incompletely written data. To fix this, the code in wcn36xx_dxe_tx_frame() was restructured a bit so that the payload descriptor is made valid before the control descriptor. Memory barriers are added to ensure coherency of shared memory areas. Signed-off-by:
-
YueHaibing authored
clk_disable_unprepare() already checks that the clock pointer is valid. No need to test it before calling it. Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by:
Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: ETSI -> FCC Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. This change itself doesn't change the selected CTL of this country and is only required to stay in sync with the QCA mappings. Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. This change itself doesn't change the selected CTL of this country and is only required to stay in sync with the QCA mappings. Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. This change itself doesn't change the selected CTL of this country and is only required to stay in sync with the QCA mappings. Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: ETSI -> FCC Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> FCC Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. This change itself doesn't change the selected CTL of this country and is only required to stay in sync with the QCA mappings. Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. This change itself doesn't change the selected CTL of this country and is only required to stay in sync with the QCA mappings. Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. This change itself doesn't change the selected CTL of this country and is only required to stay in sync with the QCA mappings. Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: FCC -> ETSI Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> FCC Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. This change itself doesn't change the selected CTL of this country and is only required to stay in sync with the QCA mappings. Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't correctly mapped to the actual CTL entries in EEPROM then it could happen that the device violates the regulations. But it can also happen that the device is then not able to be used with its full txpower on all rates. The CTL mappings for this regdomain code were now changed to: * 2.4GHz: ETSI * 5GHz: NO_CTL -> ETSI Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this regdomain code are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this regdomain code are: * 2.4GHz: ETSI * 5GHz: ETSI Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this regdomain code are: * 2.4GHz: ETSI * 5GHz: ETSI Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this regdomain code are: * 2.4GHz: ETSI * 5GHz: ETSI Signed-off-by:
-
Sven Eckelmann authored
The regdomain code is used to select the correct the correct conformance test limits (CTL) for a country. If the regdomain code isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this regdomain code are: * 2.4GHz: FCC * 5GHz: FCC Signed-off-by:
-
Sven Eckelmann authored
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by:
-
Sven Eckelmann authored
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by:
-
Sven Eckelmann authored
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: ETSI Signed-off-by:
-
Sven Eckelmann authored
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by:
-
Sven Eckelmann authored
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: FCC * 5GHz: FCC Signed-off-by:
-
Sven Eckelmann authored
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: ETSI Signed-off-by:
-
Sven Eckelmann authored
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: ETSI Signed-off-by:
-
Sven Eckelmann authored
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by:
-
Sven Eckelmann authored
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: FCC * 5GHz: FCC Signed-off-by:
-
Sven Eckelmann authored
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name and to select the correct conformance test limits (CTL) for a country. If the country isn't available and it is still programmed in the EEPROM then it will cause an error and stop the initialization with: Invalid EEPROM contents The current CTL mappings for this country are: * 2.4GHz: ETSI * 5GHz: FCC Signed-off-by:
-
Pradeep Kumar Chitrapu authored
Configure channel dwell time from duration of the scan request received from mac80211 when the duration is non-zero. When the scan request does not have duration value, use the default ones, the current implementation. Corresponding flag NL80211_EXT_FEATURE_SET_SCAN_DWELL is advertized. Supported Chipsets: -QCA988X/QCA9887 PCI -QCA99X0/QCA9984/QCA9888/QCA4019 PCI -QCA6174/QCA9377 PCI/USB/SDIO -WCN3990 SNOC Tested on QCA9984 with firmware ver 10.4-3.6-0010 Signed-off-by:
Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Signed-off-by:
-
