RCU read_lock and refcount is used to protect in-flight packets.

Use RCU and counters to manage freeing lower part of the CAIF stack if
CAIF-link layer is removed. Old solution based on delaying removal of
device is removed.

When CAIF link layer goes down the use of CAIF link layer is disabled
(by calling caif_set_phy_state()), but removal and freeing of the
lower part of the CAIF stack is done when Link layer is unregistered.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace spin_lock with rcu_read_lock when accessing lists to layers
and cache. While packets are in flight rcu_read_lock should not be held,
instead ref-counters are used in combination with RCU.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ping_table is not __read_mostly, since it contains one rwlock,
and is static to ping.c

ping_port_rover & ping_v4_lookup are static
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for a new adapter in the 82599 family.  Included
in that support is a new media_type ixgbe_media_type_fiber_lco.
Signed-of-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

error: bad constant expression
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up two minor issues in ixgbe_down.  Specifically it
addresses the fact that the VFs should not be pinged until after interrupts
are disabled otherwise they might still get a response.  It also drops the
use of the txdctl temporary variable since the only bit we should be
writing to the TXDCTL registers during a shutdown is the flush bit.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change merges the over-temp task into the service task.  As a result
all tasklets are finally combined into once single tasklet for easier
management.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change merges the ATR table reinitialization into the service task.
This is yet another opportunity to avoid any race conditions as we don't
want to be attempting to reinitialize the table during a possible reset.

In addition this change adds a counter for table reinitialization so that
it can be tracked as part of the regular statistics.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to further help to reduce possible configuration
collisions between the various tasklets.  This change combines the device
reset with the service task.  As a result it is now not possible to be
updating the link on the device while also resetting the part.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to merge the functionality of the ixgbe watchdog task
into the service task.  By doing this all link state functionality will be
controlled by a single task.  As a result the reliability of the interface
will be improved as the likelihood of any race conditions is further
reduced.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to address several race conditions with multi-speed
fiber SFP+ modules in 82599 adapters.  Specifically issues have been seen
in which both the SFP configuration and the multi-speed fiber configuration
are running simultaneously which will result in the device getting into an
erroneous link down state.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change moves flags and state into the same cacheline.  The reason for
this change is because both are frequently read around the same time and
infrequently written.  By combining them into the same cacheline this
should help to reduce memory utilization.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The semaphore can be in locked state upon driver load, particularly
on 82598 if a machine is rebooted due to panic and the semaphore was
acquired just prior to the panic.

This patch unlocks the semaphore if it times out.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add infrastructure in the PF driver to support macvlan in the VF driver.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement setup of unicast address list in the VF driver's set_rx_mode
netdev op.  Unicast addresses are sent to the PF via a mailbox message
and the PF will check if it has room in the RAR table and if so set the
filter for the VF.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The broadcast flood protection should be reset to its original value
if the primary interface could not be retrieved.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>

add_bcast_packet_to_list increases the refcount for if_incoming but the
reference count is never decreased. The reference count must be
increased for all kinds of forwarded packets which have the primary
interface stored and forw_packet_free must decrease them. Also
purge_outstanding_packets has to invoke forw_packet_free when a work
item was really cancelled.

This regression was introduced in
32ae9b22.
Reported-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>

At this point iph->daddr equals what rt->rt_dst would hold.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass in the sk_buff so that we can fetch the necessary keys from
the packet header when working with input routes.
Signed-off-by: David S. Miller <davem@davemloft.net>

This will allow ip_options_build() to reliably look at the values of
iph->{daddr,saddr}
Signed-off-by: David S. Miller <davem@davemloft.net>

This code block executes when opt->srr_is_hit is set.  It will be
set only by ip_options_rcv_srr().

ip_options_rcv_srr() walks until it hits a matching nexthop in the SRR
option addresses, and when it matches one 1) looks up the route for
that nexthop and 2) on route lookup success it writes that nexthop
value into iph->daddr.

ip_forward_options() runs later, and again walks the SRR option
addresses looking for the option matching the destination of the route
stored in skb_rtable().  This route will be the same exact one looked
up for the nexthop by ip_options_rcv_srr().

Therefore "rt->rt_dst == iph->daddr" must be true.

All it really needs to do is record the route's source address in the
matching SRR option adddress.  It need not write iph->daddr again,
since that has already been done by ip_options_rcv_srr() as detailed
above.
Signed-off-by: David S. Miller <davem@davemloft.net>

->read_proc interface is going away, switch to seq_file.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 1c5cae81 (net: call dev_alloc_name from register_netdevice),
a bug of bonding was involved, see example 1 and 2.

In register_netdevice(), the name of net_device is not valid until
dev_get_valid_name() is called. But dev->netdev_ops->ndo_init(that is
bond_init) is called before dev_get_valid_name(),
and it uses the invalid name of net_device.

I think register_netdevice() should make sure that the name of net_device is
valid before calling ndo_init().

example 1:
modprobe bonding
ls  /proc/net/bonding/bond%d

ps -eLf
root      3398     2  3398  0    1 21:34 ?        00:00:00 [bond%d]

example 2:
modprobe bonding max_bonds=3

[  170.100292] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[  170.101090] bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details.
[  170.102469] ------------[ cut here ]------------
[  170.103150] WARNING: at /home/pwp/net-next-2.6/fs/proc/generic.c:586 proc_register+0x126/0x157()
[  170.104075] Hardware name: VirtualBox
[  170.105065] proc_dir_entry 'bonding/bond%d' already registered
[  170.105613] Modules linked in: bonding(+) sunrpc ipv6 uinput microcode ppdev parport_pc parport joydev e1000 pcspkr i2c_piix4 i2c_core [last unloaded: bonding]
[  170.108397] Pid: 3457, comm: modprobe Not tainted 2.6.39-rc2+ #14
[  170.108935] Call Trace:
[  170.109382]  [<c0438f3b>] warn_slowpath_common+0x6a/0x7f
[  170.109911]  [<c051a42a>] ? proc_register+0x126/0x157
[  170.110329]  [<c0438fc3>] warn_slowpath_fmt+0x2b/0x2f
[  170.110846]  [<c051a42a>] proc_register+0x126/0x157
[  170.111870]  [<c051a4dd>] proc_create_data+0x82/0x98
[  170.112335]  [<f94e6af6>] bond_create_proc_entry+0x3f/0x73 [bonding]
[  170.112905]  [<f94dd806>] bond_init+0x77/0xa5 [bonding]
[  170.113319]  [<c0721ac6>] register_netdevice+0x8c/0x1d3
[  170.113848]  [<f94e0e30>] bond_create+0x6c/0x90 [bonding]
[  170.114322]  [<f94f4763>] bonding_init+0x763/0x7b1 [bonding]
[  170.114879]  [<c0401240>] do_one_initcall+0x76/0x122
[  170.115317]  [<f94f4000>] ? 0xf94f3fff
[  170.115799]  [<c0463f1e>] sys_init_module+0x1286/0x140d
[  170.116879]  [<c07c6d9f>] sysenter_do_call+0x12/0x28
[  170.117404] ---[ end trace 64e4fac3ae5fff1a ]---
[  170.117924] bond%d: Warning: failed to register to debugfs
[  170.128728] ------------[ cut here ]------------
[  170.129360] WARNING: at /home/pwp/net-next-2.6/fs/proc/generic.c:586 proc_register+0x126/0x157()
[  170.130323] Hardware name: VirtualBox
[  170.130797] proc_dir_entry 'bonding/bond%d' already registered
[  170.131315] Modules linked in: bonding(+) sunrpc ipv6 uinput microcode ppdev parport_pc parport joydev e1000 pcspkr i2c_piix4 i2c_core [last unloaded: bonding]
[  170.133731] Pid: 3457, comm: modprobe Tainted: G        W   2.6.39-rc2+ #14
[  170.134308] Call Trace:
[  170.134743]  [<c0438f3b>] warn_slowpath_common+0x6a/0x7f
[  170.135305]  [<c051a42a>] ? proc_register+0x126/0x157
[  170.135820]  [<c0438fc3>] warn_slowpath_fmt+0x2b/0x2f
[  170.137168]  [<c051a42a>] proc_register+0x126/0x157
[  170.137700]  [<c051a4dd>] proc_create_data+0x82/0x98
[  170.138174]  [<f94e6af6>] bond_create_proc_entry+0x3f/0x73 [bonding]
[  170.138745]  [<f94dd806>] bond_init+0x77/0xa5 [bonding]
[  170.139278]  [<c0721ac6>] register_netdevice+0x8c/0x1d3
[  170.139828]  [<f94e0e30>] bond_create+0x6c/0x90 [bonding]
[  170.140361]  [<f94f4763>] bonding_init+0x763/0x7b1 [bonding]
[  170.140927]  [<c0401240>] do_one_initcall+0x76/0x122
[  170.141494]  [<f94f4000>] ? 0xf94f3fff
[  170.141975]  [<c0463f1e>] sys_init_module+0x1286/0x140d
[  170.142463]  [<c07c6d9f>] sysenter_do_call+0x12/0x28
[  170.142974] ---[ end trace 64e4fac3ae5fff1b ]---
[  170.144949] bond%d: Warning: failed to register to debugfs
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a bug in the set_pauseparam
function that didn't well manage the ANE
field and returned broken values when use
ethtool -A|-a.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver used to call phy's ethtool configuration routine to start
auto-negotiation. This change has it call directly phy's routine to
start auto-negotiation.

The initial version was hiding phy_start_aneg() return value,
this patch returns it (<0 upon error).

Tested: module compiles, tested on STM HDK7108 STB.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The file st5481_init.c locally defines and initializes the adapter_list
variable, but does not use it for anything.  Removing the list makes it
possible to remove the list field from the st5481_adapter data structure.
In the function probe_st5481, it also makes it possible to free the locally
allocated adapter value on an error exit.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds IPPROTO_ICMP socket kind.  It makes it possible to send
ICMP_ECHO messages and receive the corresponding ICMP_ECHOREPLY messages
without any special privileges.  In other words, the patch makes it
possible to implement setuid-less and CAP_NET_RAW-less /bin/ping.  In
order not to increase the kernel's attack surface, the new functionality
is disabled by default, but is enabled at bootup by supporting Linux
distributions, optionally with restriction to a group or a group range
(see below).

Similar functionality is implemented in Mac OS X:
http://www.manpagez.com/man/4/icmp/

A new ping socket is created with

    socket(PF_INET, SOCK_DGRAM, PROT_ICMP)

Message identifiers (octets 4-5 of ICMP header) are interpreted as local
ports. Addresses are stored in struct sockaddr_in. No port numbers are
reserved for privileged processes, port 0 is reserved for API ("let the
kernel pick a free number"). There is no notion of remote ports, remote
port numbers provided by the user (e.g. in connect()) are ignored.

Data sent and received include ICMP headers. This is deliberate to:
1) Avoid the need to transport headers values like sequence numbers by
other means.
2) Make it easier to port existing programs using raw sockets.

ICMP headers given to send() are checked and sanitized. The type must be
ICMP_ECHO and the code must be zero (future extensions might relax this,
see below). The id is set to the number (local port) of the socket, the
checksum is always recomputed.

ICMP reply packets received from the network are demultiplexed according
to their id's, and are returned by recv() without any modifications.
IP header information and ICMP errors of those packets may be obtained
via ancillary data (IP_RECVTTL, IP_RETOPTS, and IP_RECVERR). ICMP source
quenches and redirects are reported as fake errors via the error queue
(IP_RECVERR); the next hop address for redirects is saved to ee_info (in
network order).

socket(2) is restricted to the group range specified in
"/proc/sys/net/ipv4/ping_group_range".  It is "1 0" by default, meaning
that nobody (not even root) may create ping sockets.  Setting it to "100
100" would grant permissions to the single group (to either make
/sbin/ping g+s and owned by this group or to grant permissions to the
"netadmins" group), "0 4294967295" would enable it for the world, "100
4294967295" would enable it for the users, but not daemons.

The existing code might be (in the unlikely case anyone needs it)
extended rather easily to handle other similar pairs of ICMP messages
(Timestamp/Reply, Information Request/Reply, Address Mask Request/Reply
etc.).

Userspace ping util & patch for it:
http://openwall.info/wiki/people/segoon/ping

For Openwall GNU/*/Linux it was the last step on the road to the
setuid-less distro.  A revision of this patch (for RHEL5/OpenVZ kernels)
is in use in Owl-current, such as in the 2011/03/12 LiveCD ISOs:
http://mirrors.kernel.org/openwall/Owl/current/iso/

Initially this functionality was written by Pavel Kankovsky for
Linux 2.4.32, but unfortunately it was never made public.

All ping options (-b, -p, -Q, -R, -s, -t, -T, -M, -I), are tested with
the patch.

PATCH v3:
    - switched to flowi4.
    - minor changes to be consistent with raw sockets code.

PATCH v2:
    - changed ping_debug() to pr_debug().
    - removed CONFIG_IP_PING.
    - removed ping_seq_fops.owner field (unused for procfs).
    - switched to proc_net_fops_create().
    - switched to %pK in seq_printf().

PATCH v1:
    - fixed checksumming bug.
    - CAP_NET_RAW may not create icmp sockets anymore.

RFC v2:
    - minor cleanups.
    - introduced sysctl'able group range to restrict socket(2).
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adapt new API.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

-Wunused-but-set-variable generates compile warnings. The affected
variables are removed.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

-Wunused-but-set-variable generates a compile warning. The affected
variable is removed.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

-Wunused-but-set-variable generates compile warnings. The affected
variables are removed.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

-Wunused-but-set-variable generates a compile warning for lcs' tasklet
function. Invoked functions contain already error handling; thus
additional return code checking is not needed here.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove unused return code handling. The claw driver is mostly dead, so
just make sure it keeps compiling without warnings.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fill in the owner of qeth's ccw device driver.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch improves FFDC (first failure data capture) by requesting
a hardware trace in case the device driver, the hardware or a user
detects an error.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set rx csum default to hw checksumming again.
Remove sysfs interface for rx csum (checksumming) and TSO (large_send).
With the new hw_features it does not work to keep the old sysfs
interface in parallel. Convert options.checksum_type to new hw_features.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update driver version number
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>