- 19 Aug, 2015 1 commit
-
-
Kirill A. Shutemov authored
commit 6b7339f4 upstream. Reading page fault handler code I've noticed that under right circumstances kernel would map anonymous pages into file mappings: if the VMA doesn't have vm_ops->fault() and the VMA wasn't fully populated on ->mmap(), kernel would handle page fault to not populated pte with do_anonymous_page(). Let's change page fault handler to use do_anonymous_page() only on anonymous VMA (->vm_ops == NULL) and make sure that the VMA is not shared. For file mappings without vm_ops->fault() or shred VMA without vm_ops, page fault on pte_none() entry would lead to SIGBUS. Signed-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by:
Oleg Nesterov <oleg@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
- 06 Aug, 2015 2 commits
-
-
Herton R. Krzesinski authored
commit 7250dc3f upstream. I received a report from an user of following mouse which needs this quirk: usb 1-1.6: USB disconnect, device number 58 usb 1-1.6: new low speed USB device number 59 using ehci_hcd usb 1-1.6: New USB device found, idVendor=04f2, idProduct=1053 usb 1-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-1.6: Product: USB Optical Mouse usb 1-1.6: Manufacturer: PixArt usb 1-1.6: configuration #1 chosen from 1 choice input: PixArt USB Optical Mouse as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.6/1-1.6:1.0/input/input5887 generic-usb 0003:04F2:1053.16FE: input,hidraw2: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-0000:00:1a.0-1.6/input0 The quirk was tested by the reporter and it fixed the frequent disconnections etc. [jkosina@suse.cz: reorder the position in hid-ids.h] Signed-off-by:
Herton R. Krzesinski <herton@redhat.com> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Cc: Oliver Neukum <ONeukum@suse.com> Signed-off-by:
-
Brian Silverman authored
commit 30a6b803 upstream. free_pi_state and exit_pi_state_list both clean up futex_pi_state's. exit_pi_state_list takes the hb lock first, and most callers of free_pi_state do too. requeue_pi doesn't, which means free_pi_state can free the pi_state out from under exit_pi_state_list. For example: task A | task B exit_pi_state_list | pi_state = | curr->pi_state_list->next | | futex_requeue(requeue_pi=1) | // pi_state is the same as | // the one in task A | free_pi_state(pi_state) | list_del_init(&pi_state->list) | kfree(pi_state) list_del_init(&pi_state->list) | Move the free_pi_state calls in requeue_pi to before it drops the hb locks which it's already holding. [ tglx: Removed a pointless free_pi_state() call and the hb->lock held debugging. The latter comes via a seperate patch ] Signed-off-by:
Brian Silverman <bsilver16384@gmail.com> Cc: austin.linux@gmail.com Cc: darren@dvhart.com Cc: peterz@infradead.org Cc: Mike Galbraith <mgalbraith@suse.de> Link: http://lkml.kernel.org/r/1414282837-23092-1-git-send-email-bsilver16384@gmail.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
- 05 Aug, 2015 1 commit
-
-
Fupan Li authored
3.12 commit 065487a1 ("x86/efi: Correct EFI boot stub use of code32_start"), upstream commit 7e8213c1 imported a bug, which will cause 32bit kernel boot to fail using EFI method. It should use the label's address instead of the value stored in the label to calculate the address of code32_start. Signed-off-by:
Fupan Li <fupan.li@windriver.com> Reviewed-by:
Matt Fleming <matt.fleming@intel.com> Signed-off-by:
-
- 04 Aug, 2015 36 commits
-
-
Jiri Slaby authored
-
Al Viro authored
commit 451a2886 upstream. unfortunately, allowing an arbitrary 16bit value means a possibility of overflow in the calculation of total number of pages in bio_map_user_iov() - we rely on there being no more than PAGE_SIZE members of sum in the first loop there. If that sum wraps around, we end up allocating too small array of pointers to pages and it's easy to overflow it in the second loop. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> [bwh: s/MAX_UIOVEC/UIO_MAXIOV/. This was fixed upstream by commit fdc81f45 ("sg_start_req(): use import_iovec()"), but we don't have that function.] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Chad Dupuis authored
commit ef86cb20 upstream. Signed-off-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by:
-
Linus Torvalds authored
commit 6f957724 upstream. The firmware class uevent function accessed the "fw_priv->buf" buffer without the proper locking and testing for NULL. This is an old bug (looks like it goes back to 2012 and commit 1244691c: "firmware loader: introduce firmware_buf"), but for some reason it's triggering only now in 4.2-rc1. Shuah Khan is trying to bisect what it is that causes this to trigger more easily, but in the meantime let's just fix the bug since others are hitting it too (at least Ingo reports having seen it as well). Reported-and-tested-by:
Shuah Khan <shuahkh@osg.samsung.com> Acked-by:
Ming Lei <ming.lei@canonical.com> Signed-off-by:
-
Joe Perches authored
commit a28e4b2b upstream. Removing unnecessary static buffers is good. Use the vsprintf %pV extension instead. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
Mikulas Patocka <mikulas@twibright.com> Signed-off-by:
-
Christoffer Dall authored
commit fd28f5d4 upstream. The current pmd_huge() and pud_huge() functions simply check if the table bit is not set and reports the entries as huge in that case. This is counter-intuitive as a clear pmd/pud cannot also be a huge pmd/pud, and it is inconsistent with at least arm and x86. To prevent others from making the same mistake as me in looking at code that calls these functions and to fix an issue with KVM on arm64 that causes memory corruption due to incorrect page reference counting resulting from this mistake, let's change the behavior. Signed-off-by:
Christoffer Dall <christoffer.dall@linaro.org> Reviewed-by:
Steve Capper <steve.capper@linaro.org> Acked-by:
Marc Zyngier <marc.zyngier@arm.com> Fixes: 084bd298 ("ARM64: mm: HugeTLB support.") Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Chris Wilson authored
commit 8b572a42 upstream. In needs_ilk_vtd_wa(), we pass in the GPU device but compared it against the ids for the mobile GPU and the mobile host bridge. That latter is impossible and so likely was just a typo for the desktop GPU device id (which is also buggy). Fixes commit da88a5f7 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Wed Feb 13 09:31:53 2013 +0000 drm/i915: Disable WC PTE updates to w/a buggy IOMMU on ILK Reported-by:
Ting-Wei Lan <lantw44@gmail.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91127 References: https://bugzilla.freedesktop.org/show_bug.cgi?id=60391Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Ilya Dryomov authored
commit 5a60e876 upstream. rbd_obj_request_create() is called on the main I/O path, so we need to use GFP_NOIO to make sure allocation doesn't blow back on us. Not all callers need this, but I'm still hardcoding the flag inside rather than making it a parameter because a) this is going to stable, and b) those callers shouldn't really use rbd_obj_request_create() and will be fixed in the future. More memory allocation fixes will follow. Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Alex Elder <elder@linaro.org> Signed-off-by:
-
Al Viro authored
commit 0a73d0a2 upstream. Signed-off-by:
-
Al Viro authored
commit a84b69cb upstream. If we'd already sent a request and decide to abort it, we *must* issue TFLUSH properly and not just blindly reuse the tag, or we'll get seriously screwed when response eventually arrives and we confuse it for response to later request that had reused the same tag. Signed-off-by:
-
Trond Myklebust authored
commit 88de6af2 upstream. req->rq_private_buf isn't initialised when xprt_setup_backchannel calls xprt_free_allocation. Fixes: fb7a0b9a ("nfs41: New backchannel helper routines") Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Jeff Layton authored
commit 764ad8ba upstream. The current buffer is much too small if you have a relatively long hostname. Bring it up to the size of the one that SETCLIENTID has. Reported-by:
Michael Skralivetsky <michael.skralivetsky@primarydata.com> Signed-off-by:
Jeff Layton <jeff.layton@primarydata.com> Signed-off-by:
-
Olga Kornievskaia authored
commit e8d975e7 upstream. Problem: When an operation like WRITE receives a BAD_STATEID, even though recovery code clears the RECLAIM_NOGRACE recovery flag before recovering the open state, because of clearing delegation state for the associated inode, nfs_inode_find_state_and_recover() gets called and it makes the same state with RECLAIM_NOGRACE flag again. As a results, when we restart looking over the open states, we end up in the infinite loop instead of breaking out in the next test of state flags. Solution: unset the RECLAIM_NOGRACE set because of calling of nfs_inode_find_state_and_recover() after returning from calling recover_open() function. Signed-off-by:
Olga Kornievskaia <kolga@netapp.com> Signed-off-by:
-
Chuck Lever authored
commit d683cc49 upstream. When encoding the NFSACL SETACL operation, reserve just the estimated size of the ACL rather than a fixed maximum. This eliminates needless zero padding on the wire that the server ignores. Fixes: ee5dc773 ('NFS: Fix "kernel BUG at fs/nfs/nfs3xdr.c:1338!"') Signed-off-by:
Chuck Lever <chuck.lever@oracle.com> Signed-off-by:
-
Uwe Kleine-König authored
commit 530c11d4 upstream. The omap watchdog has the annoying behaviour that writes to most registers don't have any effect when the watchdog is already running. Quoting the AM335x reference manual: To modify the timer counter value (the WDT_WCRR register), prescaler ratio (the WDT_WCLR[4:2] PTV bit field), delay configuration value (the WDT_WDLY[31:0] DLY_VALUE bit field), or the load value (the WDT_WLDR[31:0] TIMER_LOAD bit field), the watchdog timer must be disabled by using the start/stop sequence (the WDT_WSPR register). Currently the timer is stopped in the .probe callback but still there are possibilities that yield to a situation where omap_wdt_start is entered with the timer running (e.g. when /dev/watchdog is closed without stopping and then reopened). In such a case programming the timeout silently fails! To circumvent this stop the timer before reprogramming. Assuming one of the first things the watchdog user does is setting the timeout explicitly nothing too bad should happen because this explicit setting works fine. Fixes: 7768a13c ("[PATCH] OMAP: Add Watchdog driver support") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
Wim Van Sebroeck <wim@iguana.be> Signed-off-by:
-
Alan Stern authored
commit 3f2cee73 upstream. The usbfs API has a peculiar hole: Users are not allowed to reap their URBs after the device has been disconnected. There doesn't seem to be any good reason for this; it is an ad-hoc inconsistency. The patch allows users to issue the USBDEVFS_REAPURB and USBDEVFS_REAPURBNDELAY ioctls (together with their 32-bit counterparts on 64-bit systems) even after the device is gone. If no URBs are pending for a disconnected device then the ioctls will return -ENODEV rather than -EAGAIN, because obviously no new URBs will ever be able to complete. The patch also adds a new capability flag for USBDEVFS_GET_CAPABILITIES to indicate that the reap-after-disconnect feature is supported. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Tested-by:
Chris Dickens <christopher.a.dickens@gmail.com> Acked-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Pali Rohár authored
commit b8830a4e upstream. This commit fix kernel crash when probing for rfkill devices in dell-laptop driver failed. Function free_page() was incorrectly used on struct page * instead of virtual address of SMI buffer. This commit also simplify allocating page for SMI buffer by using __get_free_page() function instead of sequential call of functions alloc_page() and page_address(). Signed-off-by:
Pali Rohár <pali.rohar@gmail.com> Acked-by:
Michal Hocko <mhocko@suse.cz> Signed-off-by:
Darren Hart <dvhart@linux.intel.com> Signed-off-by:
-
Arnd Bergmann authored
commit 4b200b46 upstream. This fixes a several year old regression that I found while trying to get the Yoga 3 11 to work. The ideapad_rfk_set function is meant to send a command to the embedded controller through ACPI, but as of c1f73658, it sends the index of the rfkill device instead of the command, and ignores the opcode field. This changes it back to the original behavior, which indeed flips the rfkill state as seen in the debugfs interface. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Fixes: c1f73658 ("ideapad: pass ideapad_priv as argument (part 2)") Signed-off-by:
-
Damian Eppel authored
commit 56a94f13 upstream. Whilst testing cpu hotplug events on kernel configured with DEBUG_PREEMPT and DEBUG_ATOMIC_SLEEP we get following BUG message, caused by calling request_irq() and free_irq() in the context of hotplug notification (which is in this case atomic context). [ 40.785859] CPU1: Software reset [ 40.786660] BUG: sleeping function called from invalid context at mm/slub.c:1241 [ 40.786668] in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/1 [ 40.786678] Preemption disabled at:[< (null)>] (null) [ 40.786681] [ 40.786692] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.19.0-rc4-00024-g7dca860 #36 [ 40.786698] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree) [ 40.786728] [<c0014a00>] (unwind_backtrace) from [<c0011980>] (show_stack+0x10/0x14) [ 40.786747] [<c0011980>] (show_stack) from [<c0449ba0>] (dump_stack+0x70/0xbc) [ 40.786767] [<c0449ba0>] (dump_stack) from [<c00c6124>] (kmem_cache_alloc+0xd8/0x170) [ 40.786785] [<c00c6124>] (kmem_cache_alloc) from [<c005d6f8>] (request_threaded_irq+0x64/0x128) [ 40.786804] [<c005d6f8>] (request_threaded_irq) from [<c0350b8c>] (exynos4_local_timer_setup+0xc0/0x13c) [ 40.786820] [<c0350b8c>] (exynos4_local_timer_setup) from [<c0350ca8>] (exynos4_mct_cpu_notify+0x30/0xa8) [ 40.786838] [<c0350ca8>] (exynos4_mct_cpu_notify) from [<c003b330>] (notifier_call_chain+0x44/0x84) [ 40.786857] [<c003b330>] (notifier_call_chain) from [<c0022fd4>] (__cpu_notify+0x28/0x44) [ 40.786873] [<c0022fd4>] (__cpu_notify) from [<c0013714>] (secondary_start_kernel+0xec/0x150) [ 40.786886] [<c0013714>] (secondary_start_kernel) from [<40008764>] (0x40008764) Interrupts cannot be requested/freed in the CPU_STARTING/CPU_DYING notifications which run on the hotplugged cpu with interrupts and preemption disabled. To avoid the issue, request the interrupts for all possible cpus in the boot code. The interrupts are marked NO_AUTOENABLE to avoid a racy request_irq/disable_irq() sequence. The flag prevents the request_irq() code from enabling the interrupt immediately. The interrupt is then enabled in the CPU_STARTING notifier of the hotplugged cpu and again disabled with disable_irq_nosync() in the CPU_DYING notifier. [ tglx: Massaged changelog to match the patch ] Fixes: 7114cd74 ("clocksource: exynos_mct: use (request/free)_irq calls for local timer registration") Reported-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by:
Marcin Jabrzyk <m.jabrzyk@samsung.com> Signed-off-by:
Damian Eppel <d.eppel@samsung.com> Cc: m.szyprowski@samsung.com Cc: kyungmin.park@samsung.com Cc: daniel.lezcano@linaro.org Cc: kgene@kernel.org Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/1435324984-7328-1-git-send-email-d.eppel@samsung.comSigned-off-by:
-
Michal Kazior authored
commit ab499db8 upstream. There was a possible race between ieee80211_reconfig() and ieee80211_delayed_tailroom_dec(). This could result in inability to transmit data if driver crashed during roaming or rekeying and subsequent skbs with insufficient tailroom appeared. This race was probably never seen in the wild because a device driver would have to crash AND recover within 0.5s which is very unlikely. I was able to prove this race exists after changing the delay to 10s locally and crashing ath10k via debugfs immediately after GTK rekeying. In case of ath10k the counter went below 0. This was harmless but other drivers which actually require tailroom (e.g. for WEP ICV or MMIC) could end up with the counter at 0 instead of >0 and introduce insufficient skb tailroom failures because mac80211 would not resize skbs appropriately anymore. Fixes: 8d1f7ecd ("mac80211: defer tailroom counter manipulation when roaming") Signed-off-by:
Michal Kazior <michal.kazior@tieto.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Vasily Averin authored
commit d194e5d6 upstream. The final version of commit 637241a9 ("kmsg: honor dmesg_restrict sysctl on /dev/kmsg") lost few hooks, as result security_syslog() are processed incorrectly: - open of /dev/kmsg checks syslog access permissions by using check_syslog_permissions() where security_syslog() is not called if dmesg_restrict is set. - syslog syscall and /proc/kmsg calls do_syslog() where security_syslog can be executed twice (inside check_syslog_permissions() and then directly in do_syslog()) With this patch security_syslog() is called once only in all syslog-related operations regardless of dmesg_restrict value. Fixes: 637241a9 ("kmsg: honor dmesg_restrict sysctl on /dev/kmsg") Signed-off-by:
Vasily Averin <vvs@virtuozzo.com> Cc: Kees Cook <keescook@chromium.org> Cc: Josh Boyer <jwboyer@redhat.com> Cc: Eric Paris <eparis@redhat.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Chris Metcalf authored
commit 2528a8b8 upstream. bitmap_parselist("", &mask, nmaskbits) will erroneously set bit zero in the mask. The same bug is visible in cpumask_parselist() since it is layered on top of the bitmask code, e.g. if you boot with "isolcpus=", you will actually end up with cpu zero isolated. The bug was introduced in commit 4b060420 ("bitmap, irq: add smp_affinity_list interface to /proc/irq") when bitmap_parselist() was generalized to support userspace as well as kernelspace. Fixes: 4b060420 ("bitmap, irq: add smp_affinity_list interface to /proc/irq") Signed-off-by:
Chris Metcalf <cmetcalf@ezchip.com> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
-
Ding Wang authored
commit 29535f7b upstream. The current handler of MMC_BLK_CMD_ERR in mmc_blk_issue_rw_rq function may cause new coming request permanent missing when the ongoing request (previoulsy started) complete end. The problem scenario is as follows: (1) Request A is ongoing; (2) Request B arrived, and finally mmc_blk_issue_rw_rq() is called; (3) Request A encounters the MMC_BLK_CMD_ERR error; (4) In the error handling of MMC_BLK_CMD_ERR, suppose mmc_blk_cmd_err() end request A completed and return zero. Continue the error handling, suppose mmc_blk_reset() reset device success; (5) Continue the execution, while loop completed because variable ret is zero now; (6) Finally, mmc_blk_issue_rw_rq() return without processing request B. The process related to the missing request may wait that IO request complete forever, possibly crashing the application or hanging the system. Fix this issue by starting new request when reset success. Signed-off-by:
Ding Wang <justin.wang@spreadtrum.com> Fixes: 67716327 ("mmc: block: add eMMC hardware reset support") Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Sagi Grimberg authored
commit 2f1b6b7d upstream. When receiving a new iser connect request we serialize the pending requests by adding the newly created iser connection to the np accept list and let the login thread process the connect request one by one (np_accept_wait). In case we received a disconnect request before the iser_conn has begun processing (still linked in np_accept_list) we should detach it from the list and clean it up and not have the login thread process a stale connection. We do it only when the connection state is not already terminating (initiator driven disconnect) as this might lead us to access np_accept_mutex after the np was released in live shutdown scenarios. Signed-off-by:
Sagi Grimberg <sagig@mellanox.com> Signed-off-by:
Jenny Falkovich <jennyf@mellanox.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Sagi Grimberg authored
commit 4a579da2 upstream. Before we reach to connection established we may get an error event. In this case the core won't teardown this connection (never established it), so we take care of freeing it ourselves. Signed-off-by:
-
Nicholas Bellinger authored
commit 88dcd2da upstream. This patch converts iscsi-target code to use modern kthread.h API callers for creating RX/TX threads for each new iscsi_conn descriptor, and releasing associated RX/TX threads during connection shutdown. This is done using iscsit_start_kthreads() -> kthread_run() to start new kthreads from within iscsi_post_login_handler(), and invoking kthread_stop() from existing iscsit_close_connection() code. Also, convert iscsit_logout_post_handler_closesession() code to use cmpxchg when determing when iscsit_cause_connection_reinstatement() needs to sleep waiting for completion. Reported-by:
-
Lv Zheng authored
commit c04be184 upstream. ACPICA commit 90f5332a15e9d9ba83831ca700b2b9f708274658 This patch adds a new FACS initialization flag for acpi_tb_initialize(). acpi_enable_subsystem() might be invoked several times in OS bootup process, and we don't want FACS initialization to be invoked twice. Lv Zheng. Link: https://github.com/acpica/acpica/commit/90f5332aSigned-off-by:
Lv Zheng <lv.zheng@intel.com> Signed-off-by:
Bob Moore <robert.moore@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Ilya Dryomov authored
commit 82cd003a upstream. struct crush_bucket_tree::num_nodes is u8, so ceph_decode_8_safe() should be used. -Wconversion catches this, but I guess it went unnoticed in all the noise it spews. The actual problem (at least for common crushmaps) isn't the u32 -> u8 truncation though - it's the advancement by 4 bytes instead of 1 in the crushmap buffer. Fixes: http://tracker.ceph.com/issues/2759Signed-off-by:
Josh Durgin <jdurgin@redhat.com> Signed-off-by:
-
Miklos Szeredi authored
commit 0ad0b325 upstream. fc->release is called from fuse_conn_put() which was used in the error cleanup before fc->release was initialized. [Jeremiah Mahler <jmmahler@gmail.com>: assign fc->release after calling fuse_conn_init(fc) instead of before.] Signed-off-by:
Miklos Szeredi <mszeredi@suse.cz> Fixes: a325f9b9 ("fuse: update fuse_conn_init() and separate out fuse_conn_kill()") Signed-off-by:
-
Filipe Manana authored
commit 497b4050 upstream. We were allocating memory with memdup_user() but we were never releasing that memory. This affected pretty much every call to the ioctl, whether it deduplicated extents or not. This issue was reported on IRC by Julian Taylor and on the mailing list by Marcel Ritter, credit goes to them for finding the issue. Reported-by:
Julian Taylor <jtaylor.debian@googlemail.com> Reported-by:
Marcel Ritter <ritter.marcel@gmail.com> Signed-off-by:
Filipe Manana <fdmanana@suse.com> Reviewed-by:
Mark Fasheh <mfasheh@suse.de> Signed-off-by:
-
Filipe Manana authored
commit c3f4a168 upstream. The free space entries are allocated using kmem_cache_zalloc(), through __btrfs_add_free_space(), therefore we should use kmem_cache_free() and not kfree() to avoid any confusion and any potential problem. Looking at the kfree() definition at mm/slab.c it has the following comment: /* * (...) * * Don't free memory not originally allocated by kmalloc() * or you will run into trouble. */ So better be safe and use kmem_cache_free(). Signed-off-by:
David Sterba <dsterba@suse.cz> Signed-off-by:
Chris Mason <clm@fb.com> Signed-off-by:
-
Firo Yang authored
commit 4e023612 upstream. Warning like this: drivers/md/md.c: In function "update_array_info": drivers/md/md.c:6394:26: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses] !mddev->persistent != info->not_persistent|| Fix it as Neil Brown said: mddev->persistent != !info->not_persistent || Signed-off-by:
Firo Yang <firogm@gmail.com> Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
Stevens, Nick authored
commit 347d7e45 upstream. The mcp3021 scaling code is dividing the VDD (full-scale) value in millivolts by the A2D resolution to obtain the scaling factor. When VDD is 3300mV (the standard value) and the resolution is 12-bit (4096 divisions), the result is a scale factor of 3300/4096, which is always one. Effectively, the raw A2D reading is always being returned because no scaling is applied. This patch fixes the issue and simplifies the register-to-volts calculation, removing the unneeded "output_scale" struct member. Signed-off-by:
Nick Stevens <Nick.Stevens@digi.com> [Guenter Roeck: Dropped unnecessary value check] Signed-off-by:
-
Lior Amsalem authored
commit 9136291f upstream. This patch fixes a bug in the XOR driver where the cleanup function can be called and free descriptors that never been processed by the engine (which result in data errors). The cleanup function will free descriptors based on the ownership bit in the descriptors. Fixes: ff7b0479 ("dmaengine: DMA engine driver for Marvell XOR engine") Signed-off-by:
Lior Amsalem <alior@marvell.com> Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by:
Ofer Heifetz <oferh@marvell.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 6224beb1 upstream. Fengguang Wu's tests triggered a bug in the branch tracer's start up test when CONFIG_DEBUG_PREEMPT set. This was because that config adds some debug logic in the per cpu field, which calls back into the branch tracer. The branch tracer has its own recursive checks, but uses a per cpu variable to implement it. If retrieving the per cpu variable calls back into the branch tracer, you can see how things will break. Instead of using a per cpu variable, use the trace_recursion field of the current task struct. Simply set a bit when entering the branch tracing and clear it when leaving. If the bit is set on entry, just don't do the tracing. There's also the case with lockdep, as the local_irq_save() called before the recursion can also trigger code that can call back into the function. Changing that to a raw_local_irq_save() will protect that as well. This prevents the recursion and the inevitable crash that follows. Link: http://lkml.kernel.org/r/20150630141803.GA28071@wfg-t540p.sh.intel.comReported-by:
Fengguang Wu <fengguang.wu@intel.com> Tested-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 6b88f44e upstream. While debugging a WARN_ON() for filtering, I found that it is possible for the filter string to be referenced after its end. With the filter: # echo '>' > /sys/kernel/debug/events/ext4/ext4_truncate_exit/filter The filter_parse() function can call infix_get_op() which calls infix_advance() that updates the infix filter pointers for the cnt and tail without checking if the filter is already at the end, which will put the cnt to zero and the tail beyond the end. The loop then calls infix_next() that has ps->infix.cnt--; return ps->infix.string[ps->infix.tail++]; The cnt will now be below zero, and the tail that is returned is already passed the end of the filter string. So far the allocation of the filter string usually has some buffer that is zeroed out, but if the filter string is of the exact size of the allocated buffer there's no guarantee that the charater after the nul terminating character will be zero. Luckily, only root can write to the filter. Signed-off-by:
-
