As reported by a static code analyzer, the code for the ordering of
the linked list can be simplified.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

kvfree() helper is now available, use it instead of open code it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Patch fixes following sparse warning:

  CHECK   arch/x86/crypto/des3_ede_glue.c
arch/x86/crypto/des3_ede_glue.c:308:52: warning: restricted __be64 degrades to integer
arch/x86/crypto/des3_ede_glue.c:309:52: warning: restricted __be64 degrades to integer
arch/x86/crypto/des3_ede_glue.c:310:52: warning: restricted __be64 degrades to integer
arch/x86/crypto/des3_ede_glue.c:326:44: warning: restricted __be64 degrades to integer
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

At few places in caamhash and caamalg, after allocating a dmable
buffer for sg table , the buffer was being modified.  As per
definition of DMA_FROM_DEVICE ,afer allocation the memory should
be treated as read-only by the driver. This patch shifts the
allocation of dmable buffer for sg table after it is populated
by the  driver, making it read-only as per the DMA API's requirement.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

CAAM IP has certain 64 bit registers . 32 bit architectures cannot force
atomic-64 operations.  This patch adds definition of these atomic-64
operations for little endian platforms. The definitions which existed
previously were for big endian platforms.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

For platforms with virtualization enabled

    1. The job ring registers can be written to only is the job ring has been
       started i.e STARTR bit in JRSTART register is 1

    2. For DECO's under direct software control, with virtualization enabled
       PL, BMT, ICID and SDID values need to be provided. These are provided by
       selecting a Job ring in start mode whose parameters would be used for the
       DECO access programming.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Some registers like SECVID, CHAVID, CHA Revision Number,
CTPR were defined as 64 bit resgisters.  The IP provides
a DWT bit(Double word Transpose) to transpose the two words when
a double word register is accessed. However setting this bit
would also affect the operation of job descriptors as well as
other registers which are truly double word in nature.
So, for the IP to work correctly on big-endian as well as
little-endian SoC's, change is required to access all 32 bit
registers as 32 bit quantities.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

qat adds -I to the ccflags.  Unfortunately it uses CURDIR which
breaks when make is invoked with O=.  This patch replaces CURDIR
with $(src) which should work with/without O=.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This adds 4 test vectors for GHASH (of which one for chunked mode), making
a total of 5.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch introduces "by8" AES CTR mode AVX optimization inspired by
Intel Optimized IPSEC Cryptograhpic library. For additional information,
please see:
http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=22972

The functions aes_ctr_enc_128_avx_by8(), aes_ctr_enc_192_avx_by8() and
aes_ctr_enc_256_avx_by8() are adapted from
Intel Optimized IPSEC Cryptographic library. When both AES and AVX features
are enabled in a platform, the glue code in AESNI module overrieds the
existing "by4" CTR mode en/decryption with the "by8"
AES CTR mode en/decryption.

On a Haswell desktop, with turbo disabled and all cpus running
at maximum frequency, the "by8" CTR mode optimization
shows better performance results across data & key sizes
as measured by tcrypt.

The average performance improvement of the "by8" version over the "by4"
version is as follows:

For 128 bit key and data sizes >= 256 bytes, there is a 10-16% improvement.
For 192 bit key and data sizes >= 256 bytes, there is a 20-22% improvement.
For 256 bit key and data sizes >= 256 bytes, there is a 20-25% improvement.

A typical run of tcrypt with AES CTR mode encryption of the "by4" and "by8"
optimization shows the following results:

tcrypt with "by4" AES CTR mode encryption optimization on a Haswell Desktop:
---------------------------------------------------------------------------

testing speed of __ctr-aes-aesni encryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 343 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 336 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 491 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 1130 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 7309 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 346 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 361 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 543 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 1321 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 9649 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 369 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 366 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 595 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 1531 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 10522 cycles (8192 bytes)

testing speed of __ctr-aes-aesni decryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 336 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 350 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 487 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 1129 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 7287 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 350 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 359 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 635 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 1324 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 9595 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 364 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 377 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 604 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 1527 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 10549 cycles (8192 bytes)

tcrypt with "by8" AES CTR mode encryption optimization on a Haswell Desktop:
---------------------------------------------------------------------------

testing speed of __ctr-aes-aesni encryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 340 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 330 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 450 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 1043 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 6597 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 339 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 352 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 539 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 1153 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 8458 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 353 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 360 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 512 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 1277 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 8745 cycles (8192 bytes)

testing speed of __ctr-aes-aesni decryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 348 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 335 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 451 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 1030 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 6611 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 354 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 346 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 488 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 1154 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 8390 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 357 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 362 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 515 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 1284 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 8681 cycles (8192 bytes)

crypto: Incorporate feed back to AES CTR mode optimization patch

Specifically, the following:
a) alignment around main loop in aes_ctrby8_avx_x86_64.S
b) .rodata around data constants used in the assembely code.
c) the use of CONFIG_AVX in the glue code.
d) fix up white space.
e) informational message for "by8" AES CTR mode optimization
f) "by8" AES CTR mode optimization can be simply enabled
if the platform supports both AES and AVX features. The
optimization works superbly on Sandybridge as well.

Testing on Haswell shows no performance change since the last.

Testing on Sandybridge shows that the "by8" AES CTR mode optimization
greatly improves performance.

tcrypt log with "by4" AES CTR mode optimization on Sandybridge
--------------------------------------------------------------

testing speed of __ctr-aes-aesni encryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 383 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 408 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 707 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 1864 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 12813 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 395 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 432 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 780 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 2132 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 15765 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 416 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 438 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 842 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 2383 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 16945 cycles (8192 bytes)

testing speed of __ctr-aes-aesni decryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 389 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 409 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 704 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 1865 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 12783 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 409 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 434 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 792 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 2151 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 15804 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 421 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 444 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 840 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 2394 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 16928 cycles (8192 bytes)

tcrypt log with "by8" AES CTR mode optimization on Sandybridge
--------------------------------------------------------------

testing speed of __ctr-aes-aesni encryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 383 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 401 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 522 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 1136 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 7046 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 394 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 418 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 559 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 1263 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 9072 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 408 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 428 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 595 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 1385 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 9224 cycles (8192 bytes)

testing speed of __ctr-aes-aesni decryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 390 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 402 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 530 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 1135 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 7079 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 414 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 417 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 572 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 1312 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 9073 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 415 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 454 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 598 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 1407 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 9288 cycles (8192 bytes)

crypto: Fix redundant checks

a) Fix the redundant check for cpu_has_aes
b) Fix the key length check when invoking the CTR mode "by8"
encryptor/decryptor.

crypto: fix typo in AES ctr mode transform
Signed-off-by: Chandramouli Narayanan <mouli@linux.intel.com>
Reviewed-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Patch adds x86_64 assembly implementation of Triple DES EDE cipher algorithm.
Two assembly implementations are provided. First is regular 'one-block at
time' encrypt/decrypt function. Second is 'three-blocks at time' function that
gains performance increase on out-of-order CPUs.

tcrypt test results:

Intel Core i5-4570:

des3_ede-asm vs des3_ede-generic:
size    ecb-enc ecb-dec cbc-enc cbc-dec ctr-enc ctr-dec
16B     1.21x   1.22x   1.27x   1.36x   1.25x   1.25x
64B     1.98x   1.96x   1.23x   2.04x   2.01x   2.00x
256B    2.34x   2.37x   1.21x   2.40x   2.38x   2.39x
1024B   2.50x   2.47x   1.22x   2.51x   2.52x   2.51x
8192B   2.51x   2.53x   1.21x   2.56x   2.54x   2.55x
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The FIFOST_CONT_MASK define is cut and pasted twice so we can delete the
second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

There's no need for the K_table to be made of 64-bit words.  For some
reason, the original authors didn't fully reduce the values modulo the
CRC32C polynomial, and so had some 33-bit values in there.  They can
all be reduced to 32 bits.

Doing that cuts the table size in half.  Since the code depends on both
pclmulq and crc32, SSE 4.1 is obviously present, so we can use pmovzxdq
to fetch it in the correct format.

This adds (measured on Ivy Bridge) 1 cycle per main loop iteration
(CRC of up to 3K bytes), less than 0.2%.  The hope is that the reduced
D-cache footprint will make up the loss in other code.

Two other related fixes:
* K_table is read-only, so belongs in .rodata, and
* There's no need for more than 8-byte alignment
Acked-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Update to makefiles etc.
Don't update the firmware/Makefile yet since there is no FW binary in
the crypto repo yet. This will be added later.

v3 - removed change to ./firmware/Makefile
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch adds DH895xCC hardware specific code.
It hooks to the common infrastructure and provides acceleration for crypto
algorithms.
Acked-by: John Griffin <john.griffin@intel.com>
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch adds acceleration engine handler part the firmware loader.
Acked-by: Bo Cui <bo.cui@intel.com>
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Karen Xiang <karen.xiang@intel.com>
Signed-off-by: Pingchaox Yang <pingchaox.yang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch adds microcode part of the firmware loader.

v4 - splits FW loader part into two smaller patches.
Acked-by: Bo Cui <bo.cui@intel.com>
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Karen Xiang <karen.xiang@intel.com>
Signed-off-by: Pingchaox Yang <pingchaox.yang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch adds qat crypto interface.
Acked-by: John Griffin <john.griffin@intel.com>
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch adds FW interface structure definitions.
Acked-by: John Griffin <john.griffin@intel.com>
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch adds a code that implements communication channel between the
driver and the firmware.
Acked-by: John Griffin <john.griffin@intel.com>
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch adds a common infractructure that will be used by all Intel(R)
QuickAssist Technology (QAT) devices.

v2 - added ./drivers/crypto/qat/Kconfig and ./drivers/crypto/qat/Makefile
v4 - splits common part into more, smaller patches
Acked-by: John Griffin <john.griffin@intel.com>
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add support for the CCP on arm64 as a platform device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch provides the documentation of the device bindings
for the AMD Cryptographic Coprocessor driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Modify the PCI device support in prep for supporting the
CCP as a platform device for arm64.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The DRBG test code implements the CAVS test approach.

As discussed for the test vectors, all DRBG types are covered with
testing. However, not every backend cipher is covered with testing. To
prevent the testmgr from logging missing testing, the NULL test is
registered for all backend ciphers not covered with specific test cases.

All currently implemented DRBG types and backend ciphers are defined
in SP800-90A. Therefore, the fips_allowed flag is set for all.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

All types of the DRBG (CTR, HMAC, Hash) are covered with test vectors.
In addition, all permutations of use cases of the DRBG are covered:

        * with and without predition resistance
        * with and without additional information string
        * with and without personalization string

As the DRBG implementation is agnositc of the specific backend cipher,
only test vectors for one specific backend cipher is used. For example:
the Hash DRBG uses the same code paths irrespectively of using SHA-256
or SHA-512. Thus, the test vectors for SHA-256 cover the testing of all
DRBG code paths of SHA-512.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The different DRBG types of CTR, Hash, HMAC can be enabled or disabled
at compile time. At least one DRBG type shall be selected.

The default is the HMAC DRBG as its code base is smallest.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The header file includes the definition of:

* DRBG data structures with
        - struct drbg_state as main structure
        - struct drbg_core referencing the backend ciphers
        - struct drbg_state_ops callbach handlers for specific code
          supporting the Hash, HMAC, CTR DRBG implementations
        - struct drbg_conc defining a linked list for input data
        - struct drbg_test_data holding the test "entropy" data for CAVS
          testing and testmgr.c
        - struct drbg_gen allowing test data, additional information
          string and personalization string data to be funneled through
          the kernel crypto API -- the DRBG requires additional
          parameters when invoking the reset and random number
          generation requests than intended by the kernel crypto API

* wrapper function to the kernel crypto API functions using struct
  drbg_gen to pass through all data needed for DRBG

* wrapper functions to kernel crypto API functions usable for testing
  code to inject test_data into the DRBG as needed by CAVS testing and
  testmgr.c.

* DRBG flags required for the operation of the DRBG and for selecting
  the particular DRBG type and backend cipher

* getter functions for data from struct drbg_core
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This is a clean-room implementation of the DRBG defined in SP800-90A.
All three viable DRBGs defined in the standard are implemented:

 * HMAC: This is the leanest DRBG and compiled per default
 * Hash: The more complex DRBG can be enabled at compile time
 * CTR: The most complex DRBG can also be enabled at compile time

The DRBG implementation offers the following:

 * All three DRBG types are implemented with a derivation function.
 * All DRBG types are available with and without prediction resistance.
 * All SHA types of SHA-1, SHA-256, SHA-384, SHA-512 are available for
   the HMAC and Hash DRBGs.
 * All AES types of AES-128, AES-192 and AES-256 are available for the
   CTR DRBG.
 * A self test is implemented with drbg_healthcheck().
 * The FIPS 140-2 continuous self test is implemented.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

References to __exit functions must be wrapped with __exit_p.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Cc: Marcelo Henrique Cerri <mhcerri@linux.vnet.ibm.com>
Cc: Fionnuala Gunter <fin@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions.  Also, linux/device.h is added to make sure the devm_*()
routine declarations are unambiguously available. Earlier, in the probe
function ctrlpriv was leaked on the failure of ctrl = of_iomap(nprop, 0);
as well as on the failure of ctrlpriv->jrpdev = kzalloc(...); . These
two bugs have been fixed by the patch.

The following Coccinelle semantic patch was used for making the change:

identifier p, probefn, removefn;
@@
struct platform_driver p = {
  .probe = probefn,
  .remove = removefn,
};

@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
  <+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
  ...
?-kfree(e);
  ...+>
}

@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
  <...
- kfree(e);
  ...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

zswap allocates one LZO context per online cpu.

Using vmalloc() for small (16KB) memory areas has drawback of slowing
down /proc/vmallocinfo and /proc/meminfo reads, TLB pressure and poor
NUMA locality, as default NUMA policy at boot time is to interleave
pages :

edumazet:~# grep lzo /proc/vmallocinfo | head -4
0xffffc90006062000-0xffffc90006067000   20480 lzo_init+0x1b/0x30 pages=4 vmalloc N0=2 N1=2
0xffffc90006067000-0xffffc9000606c000   20480 lzo_init+0x1b/0x30 pages=4 vmalloc N0=2 N1=2
0xffffc9000606c000-0xffffc90006071000   20480 lzo_init+0x1b/0x30 pages=4 vmalloc N0=2 N1=2
0xffffc90006071000-0xffffc90006076000   20480 lzo_init+0x1b/0x30 pages=4 vmalloc N0=2 N1=2

This patch tries a regular kmalloc() and fallback to vmalloc in case
memory is too fragmented.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Use skcipher_givcrypt_cast(crypto_dequeue_request(queue)) instead, which
does the same thing in much cleaner way. The skcipher_givcrypt_cast()
actually uses container_of() instead of messing around with offsetof()
too.
Signed-off-by: Marek Vasut <marex@denx.de>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

It makes no sense for crypto_yield() to be defined in scatterwalk.h ,
move it into algapi.h as it's an internal function to crypto API.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Pull networking fixes from David Miller:

 1) Fix checksumming regressions, from Tom Herbert.

 2) Undo unintentional permissions changes for SCTP rto_alpha and
    rto_beta sysfs knobs, from Denial Borkmann.

 3) VXLAN, like other IP tunnels, should advertize it's encapsulation
    size using dev->needed_headroom instead of dev->hard_header_len.
    From Cong Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: sctp: fix permissions for rto_alpha and rto_beta knobs
  vxlan: Checksum fixes
  net: add skb_pop_rcv_encapsulation
  udp: call __skb_checksum_complete when doing full checksum
  net: Fix save software checksum complete
  net: Fix GSO constants to match NETIF flags
  udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
  vxlan: use dev->needed_headroom instead of dev->hard_header_len
  MAINTAINERS: update cxgb4 maintainer

Pull more clock framework updates from Mike Turquette:
 "This contains the second half the of the clk changes for 3.16.

  They are simply fixes and code refactoring for the OMAP clock drivers.
  The sunxi clock driver changes include splitting out the one
  mega-driver into several smaller pieces and adding support for the A31
  SoC clocks"

* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
  clk: sunxi: document PRCM clock compatible strings
  clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
  clk: sun6i: Protect SDRAM gating bit
  clk: sun6i: Protect CPU clock
  clk: sunxi: Rework clock protection code
  clk: sunxi: Move the GMAC clock to a file of its own
  clk: sunxi: Move the 24M oscillator to a file of its own
  clk: sunxi: Remove calls to clk_put
  clk: sunxi: document new A31 USB clock compatible
  clk: sunxi: Implement A31 USB clock
  ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
  CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
  ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
  CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
  CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
  dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
  ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
  CLK: TI: gate: add composite interface clock to OMAP2 only build
  ARM: OMAP2: clock: add DT boot support for cpufreq_ck
  CLK: TI: OMAP2: add clock init support
  ...

Pull NVMe update from Matthew Wilcox:
 "Mostly bugfixes again for the NVMe driver.  I'd like to call out the
  exported tracepoint in the block layer; I believe Keith has cleared
  this with Jens.

  We've had a few reports from people who're really pounding on NVMe
  devices at scale, hence the timeout changes (and new module
  parameters), hotplug cpu deadlock, tracepoints, and minor performance
  tweaks"

[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
  end up going away when mq conversion happens ]

* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
  NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
  NVMe: Use Log Page constants in SCSI emulation
  NVMe: Define Log Page constants
  NVMe: Fix hot cpu notification dead lock
  NVMe: Rename io_timeout to nvme_io_timeout
  NVMe: Use last bytes of f/w rev SCSI Inquiry
  NVMe: Adhere to request queue block accounting enable/disable
  NVMe: Fix nvme get/put queue semantics
  NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
  NVMe: Make admin timeout a module parameter
  NVMe: Make iod bio timeout a parameter
  NVMe: Prevent possible NULL pointer dereference
  NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
  NVMe: Update data structures for NVMe 1.2
  NVMe: Enable BUILD_BUG_ON checks
  NVMe: Update namespace and controller identify structures to the 1.1a spec
  NVMe: Flush with data support
  NVMe: Configure support for block flush
  NVMe: Add tracepoints
  NVMe: Protect against badly formatted CQEs
  ...