SPVTR register configures the VLAN mode of the port to enable VLAN
stacking.

It will be used to configure VxLAN to push VLAN to the decapsulated packet.
Without this setting, Spectrum-2 overtakes the VLAN tag of decapsulated
packet for bridging.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently SFN, TNUMT and TNPC registers use separate enums for
tunnel_port.

Create one enum with a neutral name and use it.
Remove the enums that are not currently required.

The next patches add two more registers that contain tunnel_port field,
the new enum can be used for them also.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx5-updates-2020-12-01

mlx5e port TX timestamping support and MISC updates

1) Add support for port TX timestamping, for better PTP accuracy.

Currently in mlx5 HW TX timestamping is done on CQE (TX completion)
generation, which much earlier than when the packet actually goes out to
the wire, in this series Eran implements the option to do timestamping on
the port using a special SQ (Send Queue), such Send Queue will generate 2
CQEs (TX completions), the original one and a new one when the packet
leaves the port, due to the nature of this special handling, such mechanism
is an opt-in only and it is off by default to avoid any performance
degradation on normal traffic flows.

This patchset improves TX Hardware timestamping offset to be less than
40ns at a 100Gbps line rate, compared to 600ns before.

With that, making our HW compliant with G.8273.2 class C, and allow Linux
systems to be deployed in the 5G telco edge, where this standard is a must.

2) Misc updates and trivial improvements.
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: updates for -next

There are some updates for the HNS3 ethernet driver.

promiscuous configuration more flexible, #2 adds ethtool
private flags to control whether enable tx unicast promisc.

previous version:
https://patchwork.kernel.org/project/netdevbpf/cover/1606997936-22166-1-git-send-email-tanhuazhong@huawei.com/
====================

Link: https://lore.kernel.org/r/1607227575-56689-1-git-send-email-tanhuazhong@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

For DEVICE_VERSION_V2, the hardware only supports max two layer
VLAN tags, including port based tag inserted by hardware, tag in
tx buffer descriptor(get from skb->tci) and tag in packet.

For transmit packet:
If port based VLAN disabled, and vf driver gets a VLAN tag from
skb, the VLAN tag must be filled to the Outer_VLAN_TAG field
(tag near to DMAC) of tx buffer descriptor, otherwise it may
be inserted after the tag in packet.

If port based VLAN enabled, and vf driver gets a VLAN tag from
skb, the VLAN tag must be filled to the VLAN_TAG field (tag
far to DMAC) of tx buffer descriptor, otherwise it may be
conflicted with port based VLAN, and raise a hardware error.

For receive packet:
The hardware will strip the VLAN tags and fill them in the rx
buffer descriptor, no matter port based VLAN enable or not.
Because port based VLAN tag is useless for stack, so vf driver
needs to discard the port based VLAN tag get from rx buffer
descriptor when port based VLAN enabled.

So vf must know about the port based VLAN state.

For DEVICE_VERSION_V3, the hardware provides some new
configuration to improve it.

For transmit packet:
When enable tag shift mode, hardware will handle the VLAN tag
in outer_VLAN_TAG field as VLAN_TAG, so it won't conflict with
port based VLAN. And hardware also make sure the tag before
the tag in packet. So vf driver doesn't need to specify the tag
position according to the port based VLAN state anymore.

For receive packet:
When enable discard mode, hardware will strip and discard the
port based VLAN tag, so vf driver doesn't need to identify it
from rx buffer descriptor.

So modify the port based VLAN configuration, simplify the process
for vf handling the VLAN tag.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, the tx unicast promisc is always enabled when promisc
mode on. If tx unicast promisc on, a function will receive all
unicast packet from other functions belong to the same port.
Add a ethtool private flag to control whether enable tx
unicast promisc. Then the function is able to filter the
unknown unicast packets from other function.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

For DEVICE_VERSION_V2, the hardware supports enable tx and rx
promiscuous separately. But tx or rx promiscuous is active for
unicast, multicast and broadcast promiscuous simultaneously.
To support traffics between functions belong to the same port,
we always enable tx promiscuous for broadcast promiscuous, so
tx promiscuous for unicast and multicast promiscuous is also
enabled.

For DEVICE_VERSION_V3, the hardware decouples the above
relationship. Tx unicast promiscuous, rx unicast promiscuous,
tx multicast promiscuous, rx multicast promiscuous, tx broadcast
promiscuous and rx broadcast promiscuous can be enabled separately.

So add support for the new promiscuous command.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Create a function to fill the fields of struct mlx5e_create_cq_param
based on a channel. The purpose is code reuse between normal CQs, XSK
CQs and the upcoming QoS CQs.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Use the new FW caps to advertise for ip-in-ip tunnel support separately
for RX and TX.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Fix smatch warnings:

drivers/net/ethernet/mellanox/mlx5/core/esw/acl/egress_lgcy.c:105 esw_acl_egress_lgcy_setup() warn: passing zero to 'PTR_ERR'
drivers/net/ethernet/mellanox/mlx5/core/esw/acl/egress_ofld.c:177 esw_acl_egress_ofld_setup() warn: passing zero to 'PTR_ERR'
drivers/net/ethernet/mellanox/mlx5/core/esw/acl/ingress_lgcy.c:184 esw_acl_ingress_lgcy_setup() warn: passing zero to 'PTR_ERR'
drivers/net/ethernet/mellanox/mlx5/core/esw/acl/ingress_ofld.c:262 esw_acl_ingress_ofld_setup() warn: passing zero to 'PTR_ERR'

esw_acl_table_create() never returns NULL, so
NULL test should be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently, when more than one EQ is sharing an IRQ, and this IRQ is
being interrupted, all the EQs sharing the IRQ will be armed. This is
done regardless of whether an EQ has EQE.
When multiple EQs are sharing an IRQ, one or more EQs can have valid
EQEs.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Since kvzalloc will initialize the allocated memory, it is not
necessary to initialize it once again.

Fixes: 11b717d6 ("net/mlx5: E-Switch, Get reg_c0 value on CQE")
Signed-off-by: Zhu Yanjun <yanjunz@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Transmitted packet timestamping accuracy can be improved when using
timestamp from the port, instead of packet CQE creation timestamp, as
it better reflects the actual time of a packet's transmit.

TX port timestamping is supported starting from ConnectX6-DX hardware.
Although at the original completion, only CQE timestamp can be attached,
we are able to get TX port timestamping via an additional completion over
a special CQ associated with the SQ (in addition to the regular CQ).

Driver to ignore the original packet completion timestamp, and report
back the timestamp of the special CQ completion. If the absolute timestamp

diff between the two completions is greater than 1 / 128 second, ignore
the TX port timestamp as it has a jitter which is too big.
No skb will be generate out of the extra completion.

Allocate additional CQ per ptpsq, to receive the TX port timestamp.

Driver to hold an skb FIFO in order to map between transmitted skb to
the two expected completions. When using ptpsq, hold double refcount on
the skb, to gaurantee it will not get released before both completions
arrive.

Expose dedicated counters of the ptp additional CQ and connect it to the
TX health reporter.

This patch improves TX Hardware timestamping offset to be less than 40ns
at a 100Gbps line rate, compared to 600ns before.

With that, making our HW compliant with G.8273.2 class C, and allow Linux
systems to be deployed in the 5G telco edge, where this standard is a
must.
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add TX PTP port object support for better TX timestamping accuracy.
Currently, driver supports CQE based TX port timestamp. Device
also offers TX port timestamp, which has less jitter and better
reflects the actual time of a packet's transmit.

Define new driver layout called ptpsq, on which driver will create
SQs that will support TX port timestamp for their transmitted packets.
Driver to identify PTP TX skbs and steer them to these dedicated SQs
as part of the select queue ndo.

Driver to hold ptpsq per TC and report them at
netif_set_real_num_tx_queues().

Add support for all needed functionality in order to xmit and poll
completions received via ptpsq.

Add ptpsq to the TX reporter recover, diagnose and dump methods.

Creation of ptpsqs is disabled by default, and can be enabled via
tx_port_ts private flag.

This patch steer all timestamp related packets to a ptpsq, but it
does not open the port timestamp support for it. The support will
be added in the following patch.
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

MLX5E_RX_ERR_CQE Macro is used only in data-path, move it to the
appropriate header file.
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

SW group counter update function aggregates sw stats out of many
mlx5e_*_stats resides in a given mlx5e_channel_stats struct.
Split the function into a few helper functions.

This will be used later in the series to calculate specific
mlx5e_*_stats which are not defined inside mlx5e_channel_stats.
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The skb fifo push/pop API used pre-defined attributes within the
mlx5e_txqsq.
In order to share the skb fifo API with other non-SQ use cases,
change the API input to get newly defined mlx5e_skb_fifo struct.
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

In order to be able to create an SQ outside of a channel context, remove
sq->channel direct pointer. This requires adding a direct pointer to:
netdevice, priv and mlx5_core in order to support SQs that are part of
mlx5e_channel. Use channel_stats from the corresponding CQ.
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

In order to be able to create an RQ outside of a channel context, remove
rq->channel direct pointer. This requires adding a direct pointer to:
ICOSQ and priv in order to support RQs that are part of mlx5e_channel.
Use channel_stats from the corresponding CQ.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

In order to be able to create a CQ outside of a channel context, remove
cq->channel direct pointer. This requires adding a direct pointer to
channel statistics, netdevice, priv and to mlx5_core in order to support
CQs that are a part of mlx5e_channel.
In addition, parameters the were previously derived from the channel
like napi, NUMA node, channel stats and index are now assembled in
struct mlx5e_create_cq_param which is given to mlx5e_open_cq() instead
of channel pointer. Generalizing mlx5e_open_cq() allows opening CQ
outside of channel context which will be used in following patches in
the patch-set.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The drop RQ has very limited objects to be freed, and differs
from regular RQs in the context that it is freed from.
Add a dedicated function for it, use it where needed, and remove
the drop_rq-specific checks in the generic function.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

These warnings become somewhat more informative when they include the
MTU value that could not be set and not just the errno.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20201205133944.10182-1-rasmus.villemoes@prevas.dkSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Saeed Mahameed says:

====================
mlx5-next auxbus support

This pull request is targeting net-next and rdma-next branches.

This series provides mlx5 support for auxiliary bus devices.

It starts with a merge commit of tag 'auxbus-5.11-rc1' from
gregkh/driver-core into mlx5-next, then the mlx5 patches that will convert
mlx5 ulp devices (netdev, rdma, vdpa) to use the proper auxbus
infrastructure instead of the internal mlx5 device and interface management
implementation, which Leon is deleting at the end of this patchset.

Link: https://lore.kernel.org/alsa-devel/20201026111849.1035786-1-leon@kernel.org/

Thanks to everyone for the joint effort !

* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
  RDMA/mlx5: Remove IB representors dead code
  net/mlx5: Simplify eswitch mode check
  net/mlx5: Delete custom device management logic
  RDMA/mlx5: Convert mlx5_ib to use auxiliary bus
  net/mlx5e: Connect ethernet part to auxiliary bus
  vdpa/mlx5: Connect mlx5_vdpa to auxiliary bus
  net/mlx5: Register mlx5 devices to auxiliary virtual bus
  vdpa/mlx5: Make hardware definitions visible to all mlx5 devices
  net/mlx5_core: Clean driver version and name
  net/mlx5: Properly convey driver version to firmware
  driver core: auxiliary bus: minor coding style tweaks
  driver core: auxiliary bus: make remove function return void
  driver core: auxiliary bus: move slab.h from include file
  Add auxiliary bus support
====================

Link: https://lore.kernel.org/r/20201207053349.402772-1-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

All usages of the definition MAX_MSIX_P_PORT were removed.
It's not in use anymore. Remove it.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Link: https://lore.kernel.org/r/20201206091254.12476-1-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

We can remove one of the ifdef blocks here, and instead of setting both
the xfrm hw_features and features flags, then unsetting the feature
flags if not in AB, wait to set the features flags if we're actually in AB
mode.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Link: https://lore.kernel.org/r/20201205174003.578267-1-jarod@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

We sometimes run into situations where a soft/hard reset of the adapter
takes a long time or fails to complete. Having additional messages that
include important adapter state info will hopefully help understand what
is happening, reduce the guess work and minimize requests to reproduce
problems with debug patches.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Link: https://lore.kernel.org/r/20201205022235.2414110-1-sukadev@linux.ibm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Julian Wiedmann says:

====================
s390/qeth: updates 2020-12-07

please apply the following patch series for qeth to netdev's net-next tree.

Some sysfs cleanups (with the prep work in ccwgroup acked by Heiko), and
a few improvements to the code that deals with async TX completion
notifications for IQD devices.

This also brings the missing patch from the previous net-next submission.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When qeth_qdio_handle_aob() frees dangling allocations in the notified
TX buffer, there are rare tear-down cases where
qeth_drain_output_queue() would later call qeth_clear_output_buffer()
for the same buffer - and thus end up walking the buffer a second time
to check for dangling kmem_cache allocations.

Luckily current code previously scrubs such a buffer, so
qeth_clear_output_buffer() would find buf->buffer->element[i].addr as
NULL and not do anything. But this is fragile, and we can easily improve
it by consistently clearing the ->is_header flag after freeing the
allocation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reuse the QETH_QDIO_BUF_EMPTY state to indicate that a TX buffer has
been completed with a QAOB notification, and may be cleaned up by
qeth_cleanup_handled_pending().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For TX buffers that require an additional async notification via QAOB, the
TX completion code can now manage all the necessary processing if the
notification has already occurred (or is occurring concurrently).

In such cases we can avoid replacing the metadata that is associated
with the buffer's slot on the ring, and just keep using the current one.

As qeth_clear_output_buffer() will also handle any kmem cache-allocated
memory that was mapped into the TX buffer, qeth_qdio_handle_aob()
doesn't need to worry about it.

While at it, also remove the unneeded forward declaration for
qeth_init_qdio_out_buf().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All qeth devices have a minimum set of sysfs attributes, and non-OSN
devices share a group of additional attributes. Depending on whether
the device is forced to use a specific discipline, the device_type then
specifies further attributes.

Shift the common attributes into dev->groups, so that the device_type
only contains the discipline-specific attributes. This avoids exposing
the common attributes to the disciplines, and nicely cleans up our
sysfs code.

While replacing the qeth_l*_*_device_attributes() helpers, switch from
sysfs_*_groups() to the more generic device_*_groups().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bus drivers have their own way of describing the sysfs attributes that
all devices on a bus should provide.
Switch ccwgroup_attr_groups over to use bus->dev_groups, and thus
free up dev->groups for usage by the ccwgroup device drivers.

While adjusting the attribute naming, use ATTRIBUTE_GROUPS() to get rid
of some boilerplate code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

INIT_LIST_HEAD() only needs to be called on actual list heads.
While at it clarify the naming of the field.
Suggested-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Misc updates

This patchset contains miscellaneous patches we gathered in our queue.
Some of them are dependencies of larger patchsets that I will submit
later this cycle.

Patches #1-#3 perform small non-functional changes in mlxsw.

Patch #4 adds more extended ack messages in mlxsw.

Patch #5 adds devlink parameters documentation for mlxsw. To be extended
with more parameters this cycle.

Patches #6-#7 perform small changes in forwarding selftests
infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Turned out that mlxsw_sp_ipip_fib_entry_op_gre4() does not need to
figure out the IP address and virtual router id. Those are exactly
the same as in the fib_entry it is called for. So just use that and
reduce mlxsw_sp_ipip_fib_entry_op_gre4() function to only call
mlxsw_sp_ipip_fib_entry_op_gre4_rtdp() make the ipip decap op
code similar to nve.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The indicated version fixes an issue whereby the MOMTE register would by
default enable mirroring of ECN-marked traffic from all traffic classes,
once the ECN mirroring was configured. This fix is necessary for offload
of RED "ecn_mark" qevent.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suppresses the following coccinelle warning:

drivers/net/ethernet/mellanox/mlxsw/core_acl_flex_keys.c:139:3-7:
WARNING use flexible-array member instead
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suppresses the following coccinelle warning:

drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:18:15-19: WARNING use flexible-array member instead
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, mlxsw triggers the 'devlink:devlink_hwmsg' tracepoint
whenever a request is sent to the device and whenever a response is
received from it. However, the tracepoint is not triggered when an event
(e.g., port up / down) is received from the device.

Also trace EMAD events in order to log a more complete picture of all
the exchanged hardware messages.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>