- 23 Aug, 2023 3 commits
-
-
Christophe Leroy authored
powerpc/85xx: Mark some functions static and add missing includes to fix no previous prototype error corenet{32/64}_smp_defconfig leads to: CC arch/powerpc/sysdev/ehv_pic.o arch/powerpc/sysdev/ehv_pic.c:45:6: error: no previous prototype for 'ehv_pic_unmask_irq' [-Werror=missing-prototypes] 45 | void ehv_pic_unmask_irq(struct irq_data *d) | ^~~~~~~~~~~~~~~~~~ arch/powerpc/sysdev/ehv_pic.c:52:6: error: no previous prototype for 'ehv_pic_mask_irq' [-Werror=missing-prototypes] 52 | void ehv_pic_mask_irq(struct irq_data *d) | ^~~~~~~~~~~~~~~~ arch/powerpc/sysdev/ehv_pic.c:59:6: error: no previous prototype for 'ehv_pic_end_irq' [-Werror=missing-prototypes] 59 | void ehv_pic_end_irq(struct irq_data *d) | ^~~~~~~~~~~~~~~ arch/powerpc/sysdev/ehv_pic.c:66:6: error: no previous prototype for 'ehv_pic_direct_end_irq' [-Werror=missing-prototypes] 66 | void ehv_pic_direct_end_irq(struct irq_data *d) | ^~~~~~~~~~~~~~~~~~~~~~ arch/powerpc/sysdev/ehv_pic.c:71:5: error: no previous prototype for 'ehv_pic_set_affinity' [-Werror=missing-prototypes] 71 | int ehv_pic_set_affinity(struct irq_data *d, const struct cpumask *dest, | ^~~~~~~~~~~~~~~~~~~~ arch/powerpc/sysdev/ehv_pic.c:112:5: error: no previous prototype for 'ehv_pic_set_irq_type' [-Werror=missing-prototypes] 112 | int ehv_pic_set_irq_type(struct irq_data *d, unsigned int flow_type) | ^~~~~~~~~~~~~~~~~~~~ CC arch/powerpc/sysdev/fsl_rio.o arch/powerpc/sysdev/fsl_rio.c:102:5: error: no previous prototype for 'fsl_rio_mcheck_exception' [-Werror=missing-prototypes] 102 | int fsl_rio_mcheck_exception(struct pt_regs *regs) | ^~~~~~~~~~~~~~~~~~~~~~~~ arch/powerpc/sysdev/fsl_rio.c:306:5: error: no previous prototype for 'fsl_map_inb_mem' [-Werror=missing-prototypes] 306 | int fsl_map_inb_mem(struct rio_mport *mport, dma_addr_t lstart, | ^~~~~~~~~~~~~~~ arch/powerpc/sysdev/fsl_rio.c:357:6: error: no previous prototype for 'fsl_unmap_inb_mem' [-Werror=missing-prototypes] 357 | void fsl_unmap_inb_mem(struct rio_mport *mport, dma_addr_t lstart) | ^~~~~~~~~~~~~~~~~ arch/powerpc/sysdev/fsl_rio.c:445:5: error: no previous prototype for 'fsl_rio_setup' [-Werror=missing-prototypes] 445 | int fsl_rio_setup(struct platform_device *dev) | ^~~~~~~~~~~~~ CC arch/powerpc/sysdev/fsl_rmu.o arch/powerpc/sysdev/fsl_rmu.c:362:6: error: no previous prototype for 'msg_unit_error_handler' [-Werror=missing-prototypes] 362 | void msg_unit_error_handler(void) | ^~~~~~~~~~~~~~~~~~~~~~ CC arch/powerpc/platforms/85xx/corenet_generic.o arch/powerpc/platforms/85xx/corenet_generic.c:33:13: error: no previous prototype for 'corenet_gen_pic_init' [-Werror=missing-prototypes] 33 | void __init corenet_gen_pic_init(void) | ^~~~~~~~~~~~~~~~~~~~ arch/powerpc/platforms/85xx/corenet_generic.c:51:13: error: no previous prototype for 'corenet_gen_setup_arch' [-Werror=missing-prototypes] 51 | void __init corenet_gen_setup_arch(void) | ^~~~~~~~~~~~~~~~~~~~~~ arch/powerpc/platforms/85xx/corenet_generic.c:104:12: error: no previous prototype for 'corenet_gen_publish_devices' [-Werror=missing-prototypes] 104 | int __init corenet_gen_publish_devices(void) | ^~~~~~~~~~~~~~~~~~~~~~~~~~~ CC arch/powerpc/platforms/85xx/qemu_e500.o arch/powerpc/platforms/85xx/qemu_e500.c:28:13: error: no previous prototype for 'qemu_e500_pic_init' [-Werror=missing-prototypes] 28 | void __init qemu_e500_pic_init(void) | ^~~~~~~~~~~~~~~~~~ CC arch/powerpc/kernel/pmc.o arch/powerpc/kernel/pmc.c:78:6: error: no previous prototype for 'power4_enable_pmcs' [-Werror=missing-prototypes] 78 | void power4_enable_pmcs(void) | ^~~~~~~~~~~~~~~~~~ Signed-off-by:Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/c90780017b624b91771a3e4240dcbadc68137915.1692684784.git.christophe.leroy@csgroup.eu
-
Christophe Leroy authored
asm/percpu.h includes asm/paca.h which needs struct tlb_core_data which is defined in mmu-e500.h asm/percpu.h is included from asm/mmu.h in a #ifdef CONFIG_E500 before the inclusion of mmu-e500.h To fix that, move the inclusion of asm/percpu.h into mmu-e500.h after the definition of struct tlb_core_data Reported-by:
kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202308220708.nRf5AUAe-lkp@intel.com/ Closes: https://lore.kernel.org/oe-kbuild-all/202308220857.uFq2oAxM-lkp@intel.com/ Closes: https://lore.kernel.org/oe-kbuild-all/202308221055.lw3UzJIL-lkp@intel.com/ Fixes: 3a24ea0d ("powerpc/kuap: Use ASM feature fixups instead of static branches") Signed-off-by:
-
Immad Mir authored
The debugfs_create_dir returns ERR_PTR incase of an error and the correct way of checking it by using the IS_ERR inline function, and not the simple null comparision. This patch fixes this. Suggested-by:
Ivan Orlov <ivan.orlov0322@gmail.com> Signed-off-by:
Immad Mir <mirimmad17@gmail.com> Signed-off-by:
-
- 21 Aug, 2023 16 commits
-
-
Naveen N Rao authored
GCC v13.1 updated support for -fpatchable-function-entry on ppc64le to emit nops after the local entry point, rather than before it. This allows us to use this in the kernel for ftrace purposes. A new script is added under arch/powerpc/tools/ to help detect if nops are emitted after the function local entry point, or before the global entry point. With -fpatchable-function-entry, we no longer have the profiling instructions generated at function entry, so we only need to validate the presence of two nops at the ftrace location in ftrace_init_nop(). We patch the preceding instruction with 'mflr r0' to match the -mprofile-kernel ABI for subsequent ftrace use. This changes the profiling instructions used on ppc32. The default -pg option emits an additional 'stw' instruction after 'mflr r0' and before the branch to _mcount 'bl _mcount'. This is very similar to the original -mprofile-kernel implementation on ppc64le, where an additional 'std' instruction was used to save LR to its save location in the caller's stackframe. Subsequently, this additional store was removed in later compiler versions for performance reasons. The same reasons apply for ppc32 so we only patch in a 'mflr r0'. Signed-off-by:
Naveen N Rao <naveen@kernel.org> Reviewed-by:
-
Naveen N Rao authored
Implement ftrace_replace_code() to consolidate logic from the different ftrace patching routines: ftrace_make_nop(), ftrace_make_call() and ftrace_modify_call(). Note that ftrace_make_call() is still required primarily to handle patching modules during their load time. The other two routines should no longer be called. This lays the groundwork to enable better control in patching ftrace locations, including the ability to nop-out preceding profiling instructions when ftrace is disabled. Signed-off-by:
-
Naveen N Rao authored
ftrace_create_branch_inst() is clearer about its intent than ftrace_call_replace(). Signed-off-by:
-
Naveen N Rao authored
Now that we validate the ftrace location during initialization in ftrace_init_nop(), we can simplify ftrace_modify_call() to patch-in the updated branch instruction without worrying about the instructions surrounding the ftrace location. Note that we continue to ensure we have the expected branch instruction at the ftrace location before patching it with the updated branch destination. Signed-off-by:
-
Naveen N Rao authored
Now that we validate the ftrace location during initialization in ftrace_init_nop(), we can simplify ftrace_make_call() to replace the nop without worrying about the instructions surrounding the ftrace location. Note that we continue to ensure that we have a nop at the ftrace location before patching it. Signed-off-by:
-
Naveen N Rao authored
Now that we validate the ftrace location during initialization in ftrace_init_nop(), we can simplify ftrace_make_nop() to patch-in the nop without worrying about the instructions surrounding the ftrace location. Note that we continue to ensure that we have a bl to ftrace_[regs_]caller at the ftrace location before nop-ing it out. Signed-off-by:
-
Naveen N Rao authored
Currently, we validate instructions around the ftrace location every time we have to enable/disable ftrace. Introduce ftrace_init_nop() to instead perform all the validation during ftrace initialization. This allows us to simply patch the necessary instructions during enabling/disabling ftrace. Signed-off-by:
-
Naveen N Rao authored
Commit 67361cf8 ("powerpc/ftrace: Handle large kernel configs") added ftrace support for ppc64 kernel images with a text section larger than 32MB. The patch did two things: 1. Add stubs at the end of .text to branch into ftrace_[regs_]caller for functions that were out of branch range. 2. Re-purpose linker-generated long branches to _mcount to instead branch to ftrace_[regs_]caller. Before that, we only supported kernel .text up to ~32MB. With the above, we now support up to ~96MB: - The first 32MB of kernel text can branch directly into ftrace_[regs_]caller since that symbol is usually at the beginning. - The modified long_branch from (2) above is used by the next 32MB of kernel text. - The next 32MB of kernel text can use the stub at the end of text to branch back to ftrace_[regs_]caller. While re-purposing the long branch works in practice, it still restricts ftrace to kernel text up to ~96MB. The stub at the end of kernel text from (1) already enables us to extend ftrace support for kernel text up to 64MB, which fulfils the original requirement. Further, once we switch to -fpatchable-function-entry, there will not be a long branch that we can use. Stop re-purposing the linker-generated long branches for ftrace to simplify the code. If there are good reasons to support ftrace on kernels beyond 64MB, we can consider adding support by using -fpatchable-function-entry. Signed-off-by:
-
Naveen N Rao authored
Split up ftrace_modify_code() into a few helpers for future use. Also update error messages accordingly. Signed-off-by:
-
Naveen N Rao authored
ftrace_low.S has just the _mcount stub and return_to_handler(). Merge this back into ftrace_mprofile.S and ftrace_64_pg.S to keep all ftrace code together, and to allow those to evolve independently. ftrace_mprofile.S is also not an entirely accurate name since this also holds ppc32 code. This will be all the more incorrect once support for -fpatchable-function-entry is added. Rename files here to more accurately describe the code: - ftrace_mprofile.S is renamed to ftrace_entry.S - ftrace_pg.c is renamed to ftrace_64_pg.c - ftrace_64_pg.S is rename to ftrace_64_pg_entry.S Signed-off-by:
-
Naveen N Rao authored
Commit 67361cf8 ("powerpc/ftrace: Handle large kernel configs") added ftrace support for ppc64 kernel images with a text section larger than 32MB. The approach itself isn't specific to ppc64, so extend the same to also work on ppc32. While at it, reduce the space reserved for the stub from 64 bytes to 32 bytes since the different stub variants are all less than 8 instructions. To reduce use of #ifdef, a stub implementation is provided for kernel_toc_address() and -SZ_2G is cast to 'long long' to prevent errors on ppc32. Signed-off-by:
-
Naveen N Rao authored
Instead of keying off DYNAMIC_FTRACE_WITH_REGS, use FTRACE_REGS_ADDR to identify the proper ftrace trampoline address to use. Signed-off-by:
-
Naveen N Rao authored
Since we now support DYNAMIC_FTRACE_WITH_ARGS across ppc32 and ppc64 ELFv2, we can simplify function_graph tracer support code in ftrace.c Signed-off-by:
-
Naveen N Rao authored
ELFv1 support is deprecated and on the way out. Pre -mprofile-kernel ftrace support (-pg only) is very limited and is retained primarily for clang builds. It won't be necessary once clang lands support for -fpatchable-function-entry. Copy the existing ftrace code supporting these into ftrace_pg.c. ftrace.c can then be refactored and enhanced with a focus on ppc32 and ppc64 ELFv2. Signed-off-by:
-
Naveen N Rao authored
.ftrace.tramp section is not used for any purpose. This code was added all the way back in the original commit introducing support for dynamic ftrace on ppc64 modules. Remove it. Signed-off-by:
-
Naveen N Rao authored
The minimum level of gcc supported for building the kernel is v5.1. v5.x releases of gcc emitted a three instruction sequence for -mprofile-kernel: mflr r0 std r0, 16(r1) bl _mcount It is only with the v6.x releases that gcc started emitting the two instruction sequence for -mprofile-kernel, omitting the second store instruction. With the older three instruction sequence, the actual ftrace location can be the 5th instruction into a function. Update the allowed offset for ftrace location from 12 to 16 to accommodate the same. Cc: stable@vger.kernel.org Fixes: 7af82ff9 ("powerpc/ftrace: Ignore weak functions") Signed-off-by:
-
- 18 Aug, 2023 21 commits
-
-
Christophe Leroy authored
CC arch/powerpc/perf/core-fsl-emb.o arch/powerpc/perf/core-fsl-emb.c:675:6: error: no previous prototype for 'hw_perf_event_setup' [-Werror=missing-prototypes] 675 | void hw_perf_event_setup(int cpu) | ^~~~~~~~~~~~~~~~~~~ Looks like fsl_emb was completely missed by commit 3f6da390 ("perf: Rework and fix the arch CPU-hotplug hooks") So, apply same changes as commit 3f6da390 ("perf: Rework and fix the arch CPU-hotplug hooks") then commit 57ecde42 ("powerpc/perf: Convert book3s notifier to state machine callbacks") While at it, also fix following error: arch/powerpc/perf/core-fsl-emb.c: In function 'perf_event_interrupt': arch/powerpc/perf/core-fsl-emb.c:648:13: error: variable 'found' set but not used [-Werror=unused-but-set-variable] 648 | int found = 0; | ^~~~~ Fixes: 3f6da390 ("perf: Rework and fix the arch CPU-hotplug hooks") Signed-off-by: -
Mahesh Salgaonkar authored
When certain PHB HW failure causes pHyp to recover PHB, it marks the PE state as temporarily unavailable until recovery is complete. This also triggers an EEH handler in Linux which needs to notify drivers, and perform recovery. But before notifying the driver about the PCI error it uses get_adapter_status()->rpaphp_get_sensor_state()->rtas_call(get-sensor-state) operation of the hotplug_slot to determine if the slot contains a device or not. If the slot is empty, the recovery is skipped entirely. eeh_event_handler() ->eeh_handle_normal_event() ->eeh_slot_presence_check() ->get_adapter_status() ->rpaphp_get_sensor_state() ->rtas_get_sensor() ->rtas_call(get-sensor-state) However on certain PHB failures, the RTAS call rtas_call(get-sensor-state) returns extended busy error (9902) until PHB is recovered by pHyp. Once PHB is recovered, the rtas_call(get-sensor-state) returns success with correct presence status. The RTAS call interface rtas_get_sensor() loops over the RTAS call on extended delay return code (9902) until the return value is either success (0) or error (-1). This causes the EEH handler to get stuck for ~6 seconds before it could notify that the PCI error has been detected and stop any active operations. Hence with running I/O traffic, during this 6 seconds, the network driver continues its operation and hits a timeout (netdev watchdog). ------------ [52732.244731] DEBUG: ibm_read_slot_reset_state2() [52732.244762] DEBUG: ret = 0, rets[0]=5, rets[1]=1, rets[2]=4000, rets[3]=> [52732.244798] DEBUG: in eeh_slot_presence_check [52732.244804] DEBUG: error state check [52732.244807] DEBUG: Is slot hotpluggable [52732.244810] DEBUG: hotpluggable ops ? [52732.244953] DEBUG: Calling ops->get_adapter_status [52732.244958] DEBUG: calling rpaphp_get_sensor_state [52736.564262] ------------[ cut here ]------------ [52736.564299] NETDEV WATCHDOG: enP64p1s0f3 (tg3): transmit queue 0 timed o> [52736.564324] WARNING: CPU: 1442 PID: 0 at net/sched/sch_generic.c:478 dev> [...] [52736.564505] NIP [c000000000c32368] dev_watchdog+0x438/0x440 [52736.564513] LR [c000000000c32364] dev_watchdog+0x434/0x440 ------------ On timeouts, network driver starts dumping debug information to console (e.g bnx2 driver calls bnx2x_panic_dump()), and go into recovery path while pHyp is still recovering the PHB. As part of recovery, the driver tries to reset the device and it keeps failing since every PCI read/write returns ff's. And when EEH recovery kicks-in, the driver is unable to recover the device. This impacts the ssh connection and leads to the system being inaccessible. To get the NIC working again it needs a reboot or re-assign the I/O adapter from HMC. [ 9531.168587] EEH: Beginning: 'slot_reset' [ 9531.168601] PCI 0013:01:00.0#10000: EEH: Invoking bnx2x->slot_reset() [...] [ 9614.110094] bnx2x: [bnx2x_func_stop:9129(enP19p1s0f0)]FUNC_STOP ramrod failed. Running a dry transaction [ 9614.110300] bnx2x: [bnx2x_igu_int_disable:902(enP19p1s0f0)]BUG! Proper val not read from IGU! [ 9629.178067] bnx2x: [bnx2x_fw_command:3055(enP19p1s0f0)]FW failed to respond! [ 9629.178085] bnx2x 0013:01:00.0 enP19p1s0f0: bc 7.10.4 [ 9629.178091] bnx2x: [bnx2x_fw_dump_lvl:789(enP19p1s0f0)]Cannot dump MCP info while in PCI error [ 9644.241813] bnx2x: [bnx2x_io_slot_reset:14245(enP19p1s0f0)]IO slot reset --> driver unload [...] [ 9644.241819] PCI 0013:01:00.0#10000: EEH: bnx2x driver reports: 'disconnect' [ 9644.241823] PCI 0013:01:00.1#10000: EEH: Invoking bnx2x->slot_reset() [ 9644.241827] bnx2x: [bnx2x_io_slot_reset:14229(enP19p1s0f1)]IO slot reset initializing... [ 9644.241916] bnx2x 0013:01:00.1: enabling device (0140 -> 0142) [ 9644.258604] bnx2x: [bnx2x_io_slot_reset:14245(enP19p1s0f1)]IO slot reset --> driver unload [ 9644.258612] PCI 0013:01:00.1#10000: EEH: bnx2x driver reports: 'disconnect' [ 9644.258615] EEH: Finished:'slot_reset' with aggregate recovery state:'disconnect' [ 9644.258620] EEH: Unable to recover from failure from PHB#13-PE#10000. [ 9644.261811] EEH: Beginning: 'error_detected(permanent failure)' [...] [ 9644.261823] EEH: Finished:'error_detected(permanent failure)' Hence, it becomes important to inform driver about the PCI error detection as early as possible, so that driver is aware of PCI error and waits for EEH handler's next action for successful recovery. Current implementation uses rtas_get_sensor() API which blocks the slot check state until RTAS call returns success. To avoid this, fix the PCI hotplug driver (rpaphp) to return an error (-EBUSY) if the slot presence state can not be detected immediately while PE is in EEH recovery state. Change rpaphp_get_sensor_state() to invoke rtas_call(get-sensor-state) directly only if the respective PE is in EEH recovery state, and take actions based on RTAS return status. This way EEH handler will not be blocked on rpaphp_get_sensor_state() and can immediately notify driver about the PCI error and stop any active operations. In normal cases (non-EEH case) rpaphp_get_sensor_state() will continue to invoke rtas_get_sensor() as it was earlier with no change in existing behavior. Signed-off-by:Mahesh Salgaonkar <mahesh@linux.ibm.com> Reviewed-by:
Nathan Lynch <nathanl@linux.ibm.com> Acked-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Mahesh Salgaonkar authored
Also, #define descriptive names for common rtas return codes and use it instead of numeric values. Signed-off-by:
-
Vaibhav Jain authored
This patch enables config option GENERIC_IDLE_POLL_SETUP for arch powerpc. This adds support for kernel param 'nohlt'. Powerpc kernel also supports another kernel boot-time param called 'powersave' which can also be used to disable all cpu idle-states and forces CPU to an idle-loop similar to what cpu_idle_poll() does. This patch however makes powerpc kernel-parameters better aligned to the generic boot-time parameters. Signed-off-by:
Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by:
-
Hari Bathini authored
Invoke ibm,os-term call with rtas_call_unlocked(), without using the RTAS spinlock, to avoid deadlock in the unlikely event of a machine crash while making an RTAS call. Signed-off-by:
Hari Bathini <hbathini@linux.ibm.com> Reviewed-by:
-
Nathan Lynch authored
Various char * parameters in the common powerpc selftest APIs can be const. Signed-off-by:
-
Nathan Lynch authored
Add exec_prot to to mm/.gitignore and sort the result. Signed-off-by:
-
Michal Suchanek authored
Avoid redefining the same value in multiple source. Signed-off-by:
Michal Suchanek <msuchanek@suse.de> Signed-off-by:
-
Nick Desaulniers authored
This reverts commit 9c87156c. I have not been able to reproduce the reported -Wframe-larger-than= warning (or disassembly) with clang-11 or clang-18. I don't know precisely when this was fixed in llvm, but it may be time to revert this. Closes: https://github.com/ClangBuiltLinux/linux/issues/252Signed-off-by:
Nick Desaulniers <ndesaulniers@google.com> Reviewed-by:
Nathan Chancellor <nathan@kernel.org> Signed-off-by:
-
Aneesh Kumar K.V authored
Parse the device tree in early init to find the memory block size to be used by the kernel. Consolidate the memory block size device tree parsing to one helper and use that on both powernv and pseries. We still want to use machine-specific callback because on all machine types other than powernv and pseries we continue to return MIN_MEMORY_BLOCK_SIZE. pseries_memory_block_size used to look for the second memory block (memory@x) to determine the memory_block_size value. This patch changed that to look at all memory blocks and make sure we can map them all correctly using the computed memory block size value. Add workaround to force 256MB memory block size if device driver managed memory such as GPU memory is present. This helps to add GPU memory that is not aligned to 1G. Co-developed-by:
Reza Arbab <arbab@linux.ibm.com> Signed-off-by:
"Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com> Signed-off-by:
-
Trevor Woerner authored
Drop CONFIG_IP_NF_TARGET_CLUSTERIP as it was removed in commit 9db5d918 ("netfilter: ip_tables: remove clusterip target"). Signed-off-by:
Trevor Woerner <twoerner@gmail.com> Signed-off-by:
-
Sourabh Jain authored
In case fadump_reserve_mem() fails to reserve memory, the reserve_dump_area_size variable will retain the reserve area size. This will lead to /sys/kernel/fadump/mem_reserved node displaying an incorrect memory reserved by fadump. To fix this problem, reserve dump area size variable is set to 0 if fadump failed to reserve memory. Fixes: 8255da95 ("powerpc/fadump: release all the memory above boot memory size") Signed-off-by:
Sourabh Jain <sourabhjain@linux.ibm.com> Acked-by:
-
Christophe Leroy authored
A W=1 build of ppc40x_defconfig throws the followings errors: CC arch/powerpc/platforms/4xx/uic.o arch/powerpc/platforms/4xx/uic.c:274:13: warning: no previous prototype for 'uic_init_tree' [-Wmissing-prototypes] 274 | void __init uic_init_tree(void) | ^~~~~~~~~~~~~ arch/powerpc/platforms/4xx/uic.c:319:14: warning: no previous prototype for 'uic_get_irq' [-Wmissing-prototypes] 319 | unsigned int uic_get_irq(void) | ^~~~~~~~~~~ CC arch/powerpc/platforms/4xx/machine_check.o CC arch/powerpc/platforms/4xx/soc.o arch/powerpc/platforms/4xx/soc.c:193:6: warning: no previous prototype for 'ppc4xx_reset_system' [-Wmissing-prototypes] 193 | void ppc4xx_reset_system(char *cmd) | ^~~~~~~~~~~~~~~~~~~ Add missing includes to get the missing prototypes. Signed-off-by: -
Christophe Leroy authored
A W=1 build of 44x/iss476-smp_defconfig gives: arch/powerpc/mm/nohash/44x.c:220:13: error: no previous prototype for 'mmu_init_secondary' [-Werror=missing-prototypes] 220 | void __init mmu_init_secondary(int cpu) | ^~~~~~~~~~~~~~~~~~ That function is called from head_4xx.S Add a prototype in mmu_decl.h Signed-off-by: -
Christophe Leroy authored
4xx/iss476-smp_defconfig leads to: CC arch/powerpc/mm/nohash/tlb.o arch/powerpc/mm/nohash/tlb.c:322:13: error: no previous prototype for 'early_init_mmu_47x' [-Werror=missing-prototypes] 322 | void __init early_init_mmu_47x(void) | ^~~~~~~~~~~~~~~~~~ early_init_mmu_47x() is used only at one place and only locally. Fold it into its only caller and remove it. Signed-off-by: -
Christophe Leroy authored
ppc4xx_defconfig with W=1 results in: CC arch/powerpc/platforms/44x/warp.o arch/powerpc/platforms/44x/warp.c:369:5: error: no previous prototype for 'pika_dtm_register_shutdown' [-Werror=missing-prototypes] 369 | int pika_dtm_register_shutdown(void (*func)(void *arg), void *arg) | ^~~~~~~~~~~~~~~~~~~~~~~~~~ arch/powerpc/platforms/44x/warp.c:374:5: error: no previous prototype for 'pika_dtm_unregister_shutdown' [-Werror=missing-prototypes] 374 | int pika_dtm_unregister_shutdown(void (*func)(void *arg), void *arg) | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~ The functions were added by commit 4ebef31f ("[POWERPC] PIKA Warp: Update platform code to support Rev B boards") Those functions are not used localy and allthough their symbols are exported they are not declared in any header file so they can't be used. Remove them, then remove the associated list as it will now remain empty hence becomes useless. Signed-off-by: -
Christophe Leroy authored
Building ppc40x_defconfig throws the following error: CC arch/powerpc/kernel/traps.o arch/powerpc/kernel/traps.c:2232:29: warning: no previous prototype for 'WatchdogHandler' [-Wmissing-prototypes] 2232 | void __attribute__ ((weak)) WatchdogHandler(struct pt_regs *regs) | ^~~~~~~~~~~~~~~ This function was imported by commit 14cf11af ("powerpc: Merge enough to start building in arch/powerpc.") as a weak function but never defined and/or called outside traps.c As it has only one caller fold it inside its caller and remove it. Signed-off-by:Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Christophe Leroy authored
__set_pte_at() handles 3 main cases with #ifdefs plus the 'percpu' subcase which leads to code duplication. Rewrite the function using IS_ENABLED() to minimise the total number of cases and remove duplicated code. Signed-off-by:
-
Christophe Leroy authored
A W=1 build of mpc885_ads_defconfig throws the following error: CC arch/powerpc/platforms/8xx/m8xx_setup.o arch/powerpc/platforms/8xx/m8xx_setup.c:41:1: error: no previous prototype for 'init_internal_rtc' [-Werror=missing-prototypes] 41 | init_internal_rtc(void) | ^~~~~~~~~~~~~~~~~ init_internal_rtc() was introduced by commit df34403d ("[POWERPC] 8xx: Add mpc885ads support and common mpc8xx files") as a weak function but has never been defined and/or used outside m8xx_setup.c As it is called only once there, just fold it into its caller and remove it. Signed-off-by: -
Christophe Leroy authored
CONFIG_8272 is never used, remove it. CONFIG_8260 is redundant with CONFIG_PPC_82xx, remove it. Signed-off-by:
-
Christophe Leroy authored
Commit 859b21a0 ("powerpc: drop PowerQUICC II Family ADS platform support") removed last user of pq2_init_pci. Remove it. Signed-off-by:
-
