Since commit bbc4d71d ("net: phy: realtek: fix rtl8211e rx/tx
delay config") iSCSI booting fails on the Pine A64 LTS.

This patch changes the phy-mode to use internal delays both for RX and TX
as has been done for other boards affected by the same commit.

Fixes: bbc4d71d ("net: phy: realtek: fix rtl8211e rx/tx delay config")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201129162627.1244808-1-xypron.glpk@gmx.de

The RX/TX delays for the Ethernet PHY on the Linksprite pcDuino 3 Nano
are configured in hardware, using resistors that are populated to pull
the RTL8211E's RXDLY/TXDLY pins low or high as needed.

phy-mode should be set to rgmii-id to reflect this. Previously it was
set to rgmii, which used to work but now results in the delays being
disabled again as a result of the bugfix in commit bbc4d71d ("net:
phy: realtek: fix rtl8211e rx/tx delay config").

Tested on two pcDuino 3 Nano boards purchased in 2015. Without this fix,
Ethernet works unreliably on one board and doesn't work at all on the
other.

Fixes: 061035d4 ("ARM: dts: sun7i: Add dts file for pcDuino 3 Nano board")
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201123174739.6809-1-ats@offog.org

Currently the GIC node in V3s DTSI follows some old DT examples, and
being broken. This leads a warning at boot.

Fix this.

Fixes: f989086c ("ARM: dts: sunxi: add dtsi file for V3s SoC")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201120050851.4123759-1-icenowy@aosc.io

Ethernet PHY on BananaPi M2 Berry provides RX and TX delays. Fix ethernet
node to reflect that fact.

Fixes: 27e81e19 ("ARM: dts: sun8i: v40: bananapi-m2-berry: Enable GMAC ethernet controller")
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1604326769-39802-1-git-send-email-pgreco@centosproject.org

DCDC1 regulator powers many different subsystems. While some of them can
work at 3.0 V, some of them can not. For example, VCC-HDMI can only work
between 3.24 V and 3.36 V. According to OS images provided by the board
manufacturer this regulator should be set to 3.3 V.

Set DCDC1 and DCDC1SW to 3.3 V in order to fix this.

Fixes: 23edc168 ("ARM: dts: sun8i: Add board dts file for Banana Pi M2 Berry")
Fixes: 27e81e19 ("ARM: dts: sun8i: v40: bananapi-m2-berry: Enable GMAC ethernet controller")
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1604326755-39742-1-git-send-email-pgreco@centosproject.org

The Ethernet PHY on the Bananapi M1 has the RX and TX delays enabled on
the PHY, using pull-ups on the RXDLY and TXDLY pins.

Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d ("net: phy: realtek: fix rtl8211e
rx/tx delay config").

Fixes: 8a5b272f ("ARM: dts: sun7i: Add Banana Pi board")
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1604326600-39544-1-git-send-email-pgreco@centosproject.org

The compatible string in the Pine64 Pinecube dts diverges from the ones
used in other S3 based boards, like the LicheePi and the Elimo Impetus
and Initium. Discussion on LKML decided the PineCube should align to the
others.
Signed-off-by: Matteo Scordino <matteo.scordino@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201030234325.5865-7-matteo.scordino@gmail.com

The Allwinner V3 SoC shares the same base as the V3s but comes with
extra pins and features available. As a result, it has its dedicated
compatible string (already used in device trees), which is added here.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201031182137.1879521-2-contact@paulk.fr

RX/TX delay on OrangePi One Plus board is set on PHY. Reflect that in
ethernet node.

Fixes: 7ee32a17 ("arm64: dts: allwinner: h6: orangepi-one-plus: Enable ethernet")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Marcus Cooper <codekipper@gmail.com>
Link: https://lore.kernel.org/r/20201101072609.1681891-1-jernej.skrabec@siol.net

RX and TX delay are provided by ethernet PHY. Reflect that in ethernet
node.

Fixes: 44a94c7e ("arm64: dts: allwinner: H5: Restore EMAC changes")
Signed-off-by: Nenad Peric <nperic@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201028115817.68113-1-nperic@gmail.com

The Ethernet PHY on the Bananapi M64 has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.

Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d ("net: phy: realtek: fix rtl8211e
rx/tx delay config").

Fixes: e7295499 ("arm64: allwinner: bananapi-m64: Enable dwmac-sun8i")
Fixes: 94f44288 ("arm64: dts: allwinner: A64: Restore EMAC changes")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-10-wens@kernel.org

The Ethernet PHY on the Libre Computer ALL-H5-CC has the RX and TX
delays enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.

Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d ("net: phy: realtek: fix rtl8211e
rx/tx delay config").

Fixes: 60d0426d ("arm64: dts: allwinner: h5: Add Libre Computer ALL-H5-CC H5 board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-9-wens@kernel.org

The Ethernet PHY on the Bananapi M2+ has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.

Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d ("net: phy: realtek: fix rtl8211e
rx/tx delay config").

Fixes: 8c7ba536 ("ARM: sun8i: bananapi-m2-plus: Enable dwmac-sun8i")
Fixes: 4904337f ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Fixes: aa8fee41 ("ARM: dts: sun8i: h3: Split out non-SoC-specific parts of Bananapi M2 Plus")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-8-wens@kernel.org

The Ethernet PHY on the Cubieboard 4 and A80 Optimus have the RX
and TX delays enabled on the PHY, using pull-ups on the RXDLY and
TXDLY pins.

Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d ("net: phy: realtek: fix rtl8211e
rx/tx delay config").

Fixes: 98048143 ("ARM: dts: sun9i: cubieboard4: Enable GMAC")
Fixes: bc9bd03a ("ARM: dts: sun9i: a80-optimus: Enable GMAC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-7-wens@kernel.org

The Ethernet PHY on the Bananapi M3 and Cubietruck Plus have the RX
and TX delays enabled on the PHY, using pull-ups on the RXDLY and
TXDLY pins.

Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d ("net: phy: realtek: fix rtl8211e
rx/tx delay config").

Fixes: 03935994 ("ARM: dts: sun8i: a83t: Enable Ethernet on two boards")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-6-wens@kernel.org

The Ethernet PHY on the Orange Pi Plus 2E has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.

Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d ("net: phy: realtek: fix rtl8211e
rx/tx delay config").

Fixes: 4904337f ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Fixes: 7a78ef92 ("ARM: sun8i: h3: Enable EMAC with external PHY on Orange Pi Plus 2E")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-5-wens@kernel.org

The Ethernet PHY on the Bananapi M1+ has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.

Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d ("net: phy: realtek: fix rtl8211e
rx/tx delay config").

Fixes: 04c85eca ("ARM: dts: sun7i: Add dts file for Bananapi M1 Plus board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-4-wens@kernel.org

The Ethernet PHY on the Cubietruck has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.

Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d ("net: phy: realtek: fix rtl8211e
rx/tx delay config").

Fixes: 67073d97 ("ARM: dts: sun7i: cubietruck: Enable the GMAC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Emilio López <emilio@elopez.com.ar>
Reviewed-by: Emilio López <emilio@elopez.com.ar>
Link: https://lore.kernel.org/r/20201024162515.30032-3-wens@kernel.org

The Ethernet PHY on the A31 Hummingbird has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.

Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d ("net: phy: realtek: fix rtl8211e
rx/tx delay config").

Fixes: c220aec2 ("ARM: dts: sun6i: Add Merrii A31 Hummingbird support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-2-wens@kernel.org

This reverts commit 75ee680c.

Turns out the activity and link LEDs on the RJ45 port are active low,
just like on the Orange Pi PC.

Revert the commit that says otherwise.

Fixes: 75ee680c ("arm: sun8i: orangepi-pc-plus: Set EMAC activity LEDs to active high")
Fixes: 4904337f ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-1-wens@kernel.org

Ethernet PHY on BananaPi M2 Ultra provides RX and TX delays. Fix
ethernet node to reflect that fact.

Fixes: c36fd5a4 ("ARM: dts: sun8i: r40: bananapi-m2-ultra: Enable GMAC ethernet controller")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201025081949.783443-1-jernej.skrabec@siol.net

RX and TX delay are provided by ethernet PHY. Reflect that in ethernet
node.

Fixes: 44a94c7e ("arm64: dts: allwinner: H5: Restore EMAC changes")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201023184858.3272918-1-jernej.skrabec@siol.net

According to board schematic, PHY provides both, RX and TX delays.
However, according to "fix" Realtek provided for this board, only TX
delay should be provided by PHY.
Tests show that both variants work but TX only PHY delay works
slightly better.

Update ethernet node to reflect the fact that PHY provides TX delay.

Fixes: 94f44288 ("arm64: dts: allwinner: A64: Restore EMAC changes")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201022211301.3548422-1-jernej.skrabec@siol.net

RX/TX delay on OrangePi Win board is set on PHY. Reflect that in
ethernet node.

Fixes: 93d6a27c ("arm64: dts: allwinner: a64: Orange Pi Win: Add Ethernet node")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201022185839.2779245-1-jernej.skrabec@siol.net

Since commit bbc4d71d ("net: phy: realtek: fix rtl8211e rx/tx delay config"),
the network is unusable on PineH64 model A.

This is due to phy-mode incorrectly set to rgmii instead of rgmii-id.

Fixes: 729e1ffc ("arm64: allwinner: h6: add support for the Ethernet on Pine H64")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201019063449.33316-1-clabbe@baylibre.com

Before the commit bbc4d71d ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the software overwrite for RX/TX delays of the RTL8211e
were not working properly and the Beelink GS1 had both RX/TX delay of RGMII
interface set using pull-up on the TXDLY and RXDLY pins.

Now that these delays are working properly they overwrite the HW
config and set this to 'rgmii' meaning no delay on both RX/TX.
This makes the ethernet of this board not working anymore.

Set the phy-mode to 'rgmii-id' meaning RGMII with RX/TX delays
in the device-tree to keep the correct configuration.

Fixes: 089bee8d ("arm64: dts: allwinner: h6: Introduce Beelink GS1 board")
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201018172409.1754775-1-peron.clem@gmail.com

make dtbs_check warm about unknown address/size-cells property in the
pinetab device-tree.

This is because these information are not necessary.

Drop them.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201011211514.155266-1-peron.clem@gmail.com

Jernej has helped a lot by reviewing patches recently, so let's make it
official.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201009074423.10708-1-maxime@cerno.tech

Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.

Remove the quote operator # from compiler_attributes.h __section macro.

Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.

Conversion done using the script at:

    https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.plSigned-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace".  So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 453431a5 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.

Since then a few more instances of kzfree() have slipped in.

Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.

If GIT_DIR is unset, keep using the current ".git" default.

Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.comSigned-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Thomas Gleixner:
 "A time namespace fix and a matching selftest. The futex absolute
  timeouts which are based on CLOCK_MONOTONIC require time namespace
  corrected. This was missed in the original time namesapce support"

* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  selftests/timens: Add a test for futex()
  futex: Adjust absolute futex timeouts with per time namespace offset

Pull scheduler fixes from Thomas Gleixner:
 "Two scheduler fixes:

   - A trivial build fix for sched_feat() to compile correctly with
     CONFIG_JUMP_LABEL=n

   - Replace a zero lenght array with a flexible array"

* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/features: Fix !CONFIG_JUMP_LABEL case
  sched: Replace zero-length array with flexible-array

Pull perf fix from Thomas Gleixner:
 "A single fix to compute the field offset of the SNOOPX bit in the data
  source bitmask of perf events correctly"

* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: correct SNOOPX field offset

Pull locking fix from Thomas Gleixner:
 "Just a trivial fix for kernel-doc warnings"

* tag 'locking-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/seqlocks: Fix kernel-doc warnings

Pull NTB fixes from Jon Mason.

* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
  NTB: Use struct_size() helper in devm_kzalloc()
  ntb: intel: Fix memleak in intel_ntb_pci_probe
  NTB: hw: amd: fix an issue about leak system resources

Pull i2c fix from Wolfram Sang:
 "Regression fix for rc1 and stable kernels as well"

* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs

Pull more cifs updates from Steve French:
 "Add support for stat of various special file types (WSL reparse points
  for char, block, fifo)"

* tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number
  smb3: add some missing definitions from MS-FSCC
  smb3: remove two unused variables
  smb3: add support for stat of WSL reparse points for special file types