Only a firmware with version 2.1 and above supports dma ring feature.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add dma_ring bit in the mei message header for conveying
that the message data itself are on the dma ring.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The protocol defines how to setup an I/O ring on top of host
memory to utilize the device DMA engine for faster transport.

Three memory buffers are allocated.
A Host circular buffer for from the Host to Device communication.
A Device circular buffer for from Device to the Host communication.
And finally a Control block where the pointers for the both
circular buffers are managed.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove header size knowledge from me and txe hw layers,
this requires to change the write handler to accept
header and its length as well as data and its length.

HBM messages are fixed to use basic header, hence we add mei_hbm2slots()
that converts HBM message length and mei message header,
while mei_data2slots() converts data length directly to the slots.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The call trace:
XXX/1910 is trying to acquire lock:
 (&mm->mmap_sem){++++++}, at: [<ffffffff97008c87>] might_fault+0x57/0xb0

but task is already holding lock:
 (&idev->info_lock){+.+...}, at: [<ffffffffc0638a06>] uio_write+0x46/0x130 [uio]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (&idev->info_lock){+.+...}:
       [<ffffffff96f31fc9>] lock_acquire+0x99/0x1e0
       [<ffffffff975edad3>] mutex_lock_nested+0x93/0x410
       [<ffffffffc063873d>] uio_mmap+0x2d/0x170 [uio]
       [<ffffffff97016b58>] mmap_region+0x428/0x650
       [<ffffffff97017138>] do_mmap+0x3b8/0x4e0
       [<ffffffff96ffaba3>] vm_mmap_pgoff+0xd3/0x120
       [<ffffffff97015261>] SyS_mmap_pgoff+0x1f1/0x270
       [<ffffffff96e387c2>] SyS_mmap+0x22/0x30
       [<ffffffff975ff315>] system_call_fastpath+0x1c/0x21

-> #0 (&mm->mmap_sem){++++++}:
       [<ffffffff96f30e9c>] __lock_acquire+0xdac/0x15f0
       [<ffffffff96f31fc9>] lock_acquire+0x99/0x1e0
       [<ffffffff97008cb4>] might_fault+0x84/0xb0
       [<ffffffffc0638a74>] uio_write+0xb4/0x130 [uio]
       [<ffffffff9706ffa3>] vfs_write+0xc3/0x1f0
       [<ffffffff97070e2a>] SyS_write+0x8a/0x100
       [<ffffffff975ff315>] system_call_fastpath+0x1c/0x21

other info that might help us debug this:
 Possible unsafe locking scenario:
       CPU0                    CPU1
       ----                    ----
  lock(&idev->info_lock);
                               lock(&mm->mmap_sem);
                               lock(&idev->info_lock);
  lock(&mm->mmap_sem);

 *** DEADLOCK ***
1 lock held by XXX/1910:
 #0:  (&idev->info_lock){+.+...}, at: [<ffffffffc0638a06>] uio_write+0x46/0x130 [uio]

stack backtrace:
CPU: 0 PID: 1910 Comm: XXX Kdump: loaded Not tainted #1
Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 05/19/2017
Call Trace:
 [<ffffffff975e9211>] dump_stack+0x19/0x1b
 [<ffffffff975e260a>] print_circular_bug+0x1f9/0x207
 [<ffffffff96f2f6a7>] check_prevs_add+0x957/0x960
 [<ffffffff96f30e9c>] __lock_acquire+0xdac/0x15f0
 [<ffffffff96f2fb19>] ? mark_held_locks+0xb9/0x140
 [<ffffffff96f31fc9>] lock_acquire+0x99/0x1e0
 [<ffffffff97008c87>] ? might_fault+0x57/0xb0
 [<ffffffff97008cb4>] might_fault+0x84/0xb0
 [<ffffffff97008c87>] ? might_fault+0x57/0xb0
 [<ffffffffc0638a74>] uio_write+0xb4/0x130 [uio]
 [<ffffffff9706ffa3>] vfs_write+0xc3/0x1f0
 [<ffffffff9709349c>] ? fget_light+0xfc/0x510
 [<ffffffff97070e2a>] SyS_write+0x8a/0x100
 [<ffffffff975ff315>] system_call_fastpath+0x1c/0x21
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There are two bugs here.  First the error codes weren't set on several
paths.  And second, if the call to request_threaded_irq() inside
uio_register_device() fails then it would lead to a double free when
we call uio_unregister_device() inside pruss_cleanup().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Being able to find the numa_node for a device is useful for userspace
drivers (DPDK) and also for diagnosing performance issues.  This makes
vmbus similar to pci.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Get rid of ISA specific code from vmus_drv.c which is common code.

Fixes: 81b18bce ("Drivers: HV: Send one page worth of kmsg dump over Hyper-V during panic")
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The check to free the Hyper-V control table header was reversed. This
fixes it.

Fixes: 81b18bce ("Drivers: HV: Send one page worth of kmsg dump over Hyper-V during panic")
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The code to support panic control message was checking the return was
checking the return value from kmsg_dump_get_buffer as error value, which
is not what the routine returns. This fixes it.

Fixes: 81b18bce ("Drivers: HV: Send one page worth of kmsg dump over Hyper-V during panic")
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'fsi-updates-2018-07-27' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/linux-fsi into char-misc-next

Ben writes:

Last round of FSI updates for 4.19

This adds a few fixes for things reported since the last merge,
and the latch batch of changes pending for FSI for 4.19.

That batch is a rather mechanical conversion of the misc devices
into proper char devices.

The misc devices were ill suited, the minor space for them is
limited and we can have a lot of chips in a system creating FSI
devices.

This also allows us to better control (and fix) object lifetime
getting rid of the bad devm_kzalloc() of the structures containing
the devices etc...

Finally, we add a chardev to the core FSI that provides raw CFAM
access to FSI slaves as a replacement for the current "raw" binary
sysfs file which will be ultimately deprecated and removed.

The bus scanning process isn't terribly good at parallel attempts
at rescanning the same bus. Let's have a per-master mutex protecting
the scanning process.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This aims to deprecate the "raw" sysfs file used for directly
accessing the CFAM and instead use a char device like the
other sub drivers.

Since it reworks the slave creation code and adds a cfam device
type, we also use the opportunity to convert the attributes
to attribute groups and add a couple more.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This converts FSI scom to use the new fsi-core controlled
chardev allocator and use a real cdev instead of a miscdev.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This converts FSI sbefifo to use the new fsi-core controlled
chardev allocator and use a real cdev instead of a miscdev.

One side effect is to fix the object lifetime by removing
the use of devm_kzalloc() for something that contains kobjects,
and using proper reference counting.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The various FSI devices (sbefifo, occ, scom, more to come)
currently use misc devices.

This is problematic as the minor device space for misc is
limited and there can be a lot of them. Also it limits our
ability to move them to a dedicated /dev/fsi directory or
to be smart about device naming and numbering.

It also means we have IDAs on every single of these drivers

This creates a common fsi "device_type" for the optional
/dev/fsi grouping and a dev_t allocator for all FSI devices.

"Legacy" devices get to use a backward compatible numbering
scheme (as long as chip id <16 and there's only one copy
of a given unit type per chip).

A single major number and a single IDA are shared for all
FSI devices.

This doesn't convert the FSI device drivers to use the new
scheme yet, they will be converted individually.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

s390 defines a global dump_trace() symbol. Rename ours to
dump_ucode_trace() to avoid a collision in build tests.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

In case memory resources for *fw* were allocated, release them
before return.

Addresses-Coverity-ID: 1472044 ("Resource leak")
Fixes: 6a794a27 ("fsi: master-ast-cf: Add new FSI master using Aspeed ColdFire")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

When Thunderbolt host controller is set to RTD3 mode (Runtime D3) it is
present all the time. Because of this it is important to runtime suspend
the controller whenever possible. In case of ICM we have following rules
which all needs to be true before the host controller can be put to D3:

  - The controller firmware reports to support RTD3
  - All the connected devices announce support for RTD3
  - There is no active XDomain connection

Implement this using standard Linux runtime PM APIs so that when all the
children devices are runtime suspended, the Thunderbolt host controller
PCI device is runtime suspended as well. The ICM firmware then starts
powering down power domains towards RTD3 but it can prevent this if it
detects that there is an active Display Port stream (this is not visible
to the software, though).

The Thunderbolt host controller will be runtime resumed either when
there is a remote wake event (device is connected or disconnected), or
when there is access from userspace that requires hardware access.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Variable 'approved' is being assigned but is never used hence it is
redundant and can be removed.

Cleans up clang warning:
warning: variable 'approved' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The correct way to put the ICM into suspend state is to send it
NHI_MAILBOX_DRV_UNLOADS mailbox command. NHI_MAILBOX_SAVE_DEVS is not
needed on Intel Titan Ridge so we can skip it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the connection manager implementation needs to touch the domain
structures it ought to take the lock itself. Currently only ICM
implements these hooks and it does not need the lock because we there
will be no notifications before driver ready message is sent to it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This command is not really fast and can make resume time slower. We only
need to get route again if the link was changed and during initial
device connected message.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI defaults to 32-bit DMA mask but this device is capable of full
64-bit addressing, so make sure we first try 64-bit DMA mask before
falling back to the default 32-bit.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixes small variable name typo and the associated
checkpatch spelling warning.
Signed-off-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Then reading the RTAG/RCRC "registers" from the coprocessor after
a command is complete, mask out the top bits, only keep the relevant
bits. Microcode v5 will leave garbage in those top bits as a
result of a performance optimization.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---

If asm/cacheflush.h is included first, the following build warnings are
seen with sparc32 builds.

In file included from arch/sparc/include/asm/cacheflush.h:11:0,
        from drivers/android/binder.c:54:
arch/sparc/include/asm/cacheflush_32.h:40:37: warning:
	'struct page' declared inside parameter list will not be visible
	outside of this definition or declaration

Moving the asm/ include after linux/ includes solves the problem.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If asm/cacheflush.h is included first, the following build warnings are
seen with sparc32 builds.

In file included from ./arch/sparc/include/asm/cacheflush.h:11:0,
	from drivers/android/binder_alloc.c:20:
./arch/sparc/include/asm/cacheflush_32.h:40:37: warning:
	'struct page' declared inside parameter list

Moving the asm/ include after linux/ includes fixes the problem.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Wrap the mei header boilerplate initialization code in
mei_msg_hdr_init function. On the way remove 'completed'
field from mei_cl_cb structure as this information
is already included in the header and is local to particular
fragment.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The host buffer depth is hardware specific so it's better to
handle it inside the me and txe hw modules. In me the depth
is read from register in txe it's a constant number.
The value is now retrieved via mei_hbuf_depth accessor,
while it replaces mei_hbuf_max_len.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Cleanup conversions between slots and data.
Define MEI_SLOT_SIZE instead of using 4 or sizeof(u32) across
the source code.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A couple of places forgot the 'z' qualifier for dev_dbg
when printing a size_t
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Merge tag 'fsi-updates-2018-07-24' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/linux-fsi into char-misc-testing

Ben writes:

This adds support for offloading the FSI low level bitbanging to the
ColdFire coprocessor of the Aspeed SoCs. All the pre-requisites have
already been merged, this is the final piece in the puzzle.

This branch also pull gpio/ib-aspeed which is a topic branch already
in gpio/for-next (and thus in next) whic contains pre-requisites.

Finally, there's also a bug fix to the sbefifo driver for some
inconsistent use of a mutex in the error handling code.

They get retrieved from the device-tree and exposed
as an attribute in sysfs
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This represents a physical chip in the system and allows
a stable numbering scheme to be passed to udev for userspace
to recognize which chip is which.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Rob Herring <robh@kernel.org>

Some of the exit path missed the unlock. Move the mutex to
an outer function to avoid the problem completely
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The Aspeed AST2x00 can contain a ColdFire v1 coprocessor which
is currently unused on OpenPower systems.

This adds an alternative to the fsi-master-gpio driver that
uses that coprocessor instead of bit banging from the ARM
core itself. The end result is about 4 times faster.

The firmware for the coprocessor and its source code can be
found at https://github.com/ozbenh/cf-fsi and is system specific.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This isn't per-se a real device, it's a pseudo-device that
represents the use of the Aspeed built-in ColdFire to
implement the FSI protocol by bitbanging the GPIOs instead
of doing it from the ARM core.

Thus it's a drop-in replacement for the existing
fsi-master-gpio pseudo-device for use on systems based
on the Aspeed chips. It has most of the same properties,
plus some more needed to operate the coprocessor.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Rob Herring <robh@kernel.org>

There are still quite a few cases where a device might want
to get to a different node of the device-tree, obtain the
resources and map them.

We have of_iomap() and of_io_request_and_map() but they both
have shortcomings, such as not returning the size of the
resource found (which can be useful) and not being "managed".

This adds a devm_of_iomap() that provides all of these and
should probably replace uses of the above in most drivers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>

Merge the GPIO tree "ib-aspeed" topic branch which contains pre-requisites
for subsequent changes. This branch is also in gpio "next".