Add support for the Computer on Module Colibri iMX6ULL and its
Bluetooth/Wifi variant along with the development/evaluation carrier
board device trees. Follow the usual hierarchic include model,
maintaining shared configuration in imx6ull-colibri.dtsi and
imx6ull-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This is a rebased version of patch [0].

The 32 kHz reference clock on the i.MX6UL(L) can be output by
setting the external signal XTALOSC_REF_CLK_32K in one of the
following ways [1]:

|----------------------------------------------------------|
| Signal              | Pad             | Mode | Direction |
|----------------------------------------------------------|
| XTALOSC_REF_CLK_32K | ENET1_RX_EN     | ALT2 | O         |
|                     | GPIO1_IO03      | ALT3 |           |
|                     | JTAG_TCK        | ALT6 |           |
|----------------------------------------------------------|

Before patch [2] the mux mode for the external reference clock was
missing. The patch named the mux mode as used in the NXP Linux
4.9.11_1.0.0 release, but the Reference Manual uses the name
OSC32K_32K_OUT, e.g. in [3].

As Philipp and Shawn suggest the name from the RM should be used
instead.

[0] https://patchwork.kernel.org/patch/10172187/
[1] IMX6ULRM, Rev. 1, 04/2016, Table 58-1, p. 3649
[2] https://patchwork.kernel.org/patch/10156121/
[3] IMX6ULRM, Rev. 1, 04/2016, 30.5.47 SW_MUX_CTL_PAD_ENET1_RX_EN SW MUX
    Control Register (IOMUXC_SW_MUX_CTL_PAD_ENET1_RX_EN), p. 1357
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx6ull-14x14-evk.dts currently includes the imx6ul.dtsi file for an
i.MX6ULL SoC which is plain wrong.

Rename the current imx6ul-14x14-evk.dts to .dtsi and include it from
imx6ul-14x14-evk.dts and imx6ull-14x14-evk.dts, so that both can
include the appropriate SoC specific (imx6ul.dtsi/imx6ull.dtsi) file.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable secure debug enable register access for Bx50v3 devices to enable
PMU and hardware counters for perf.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Put the UART clock node directly under root with a unique node name and
drop unit-address in order to fix the following build warning with W=1:

arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dtb: Warning (simple_bus_reg): Node /clocks/osc26m missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The missing last digit of the CONFIG values is added. Looks like a typo
of some sort when comparing to the downstream dt. This fixes
intermittent behavior behaviour of the ethernet controllers.
Signed-off-by: Aapo Vienamo <aapo@tuxera.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The eSDHC does not work properly if the SION bit is not set for the
bidirectional CMD signal, whatever the eSDHC instance and the selected
pad. Therefore, setting SION is mandatory for all eSDHC CMD ports. Do
this for MX25_PAD_*__ESDHCn_CMD in imx25-pinfunc.h in order to enforce
this behavior for all boards.

This had already been done for eSDHC1, but not for eSDHC2. Also, define
MX25_PAD_FEC_MDC__ESDHC2_CMD so that all the possible cases are covered
from now on.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This file had several naming inconsistencies for eSDHC:
 - the instances were named sometimes SDn, sometimes SDHCn, whereas they
   are named ESDHCn in the reference manual, e.g.:
     MX25_PAD_SD1_CMD__SD1_CMD
     MX25_PAD_D15__SDHC1_DAT7
 - the data ports were named sometimes DATAn, sometimes DATn like in the
   reference manual, e.g.:
     MX25_PAD_SD1_DATA0__SD1_DATA0
     MX25_PAD_D15__SDHC1_DAT7
 - in one case, the clock port was named DAT_CLK instead of CLK:
     MX25_PAD_CSI_D7__SDHC2_DAT_CLK

This change:
 - introduces new definitions using the naming from the reference
   manual,
 - keeps definitions using the legacy naming in order not to break
   compatibility for out-of-tree users (they can be removed later),
 - updates the in-tree files that were using the legacy naming.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Using 'at24' as fallback is now deprecated - use the full
'atmel,<model>' string.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix the following warnings from dtc by adding the unit name to memory
nodes:

Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name

Converted using the following command:

perl -p0777i -e 's/memory \{\n\t\treg = \<0x+([0-9a-f])/memory\@$1$\0000000 \{\n\t\treg = <0x$1/m' `find ./arch/arm/boot/dts -name "imx*"`

The files below were manually fixed:
-imx1-ads.dts
-imx1-apf9328.dts
-imx6q-pistachio.dts
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove the empty reg property from the SoC dtsi files in order to avoid
duplicate memory nodes when the correct size is passed in board dts files.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In preparation for removing 'reg = <0 0>;' from the dtsi SoC files, pass
'reg = <0 0 >;' to the dts/dtsi board files that do not pass the memory
size.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add ARM power domain in PGC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add PU power domain support, GPU is the only
module inside PU power domain, and PU power
is supplied by LDO_SOC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch configures the board to output UART6 to the mikroBus.

The NXP WaRP7 board can route UART6 to the mikroBus, where an RS232
click board can be plugged in to get an additional serial port.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Default boot medium must be internal eMMC, we don't want the SDIO to be
used for these devices.  This commit disables the SD card interface for
GE Healthcare Bx50v3 devices.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

PPD uses the PMIC's TSI pins in general purpose ADC mode.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Utilise new support in Atmel MaxTouch driver to drive the
touchscreen controllers reset line correctly.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In i.MX 6ULL UART8 is part of the AIPS-3 memory map instead of
AIPS-1. Clocks and interrupts remain the same.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX 6ULL features another IOMUX Controller called IOMUXC
SNVS which allows to control BOOT_MODE and TAMPER pins. Add the
controller to the i.MX 6ULL specific imx6ull.dtsi device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add per-core ARM architected timer. Unfortunately bootloaders (U-Boot)
currently do not make the necessary initialization. Also specifing the
clock manually using the clock-frequency property seems not to help.
Therefor leave the timer disabled by default for now.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Cortex-A7 and its GIC support virtualization extensions. To
make use of them the CPU private interrupt needs to be specified.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On i.MX 6ULL, the pin MUX and CTRL register of BOOT_MODEx and TAMPERx
pins are available through IOMUXC_SNVS. Add additional pinfunc defines.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add previously missing daisy chain configurations and several
additional pinmux options.

Synchronized with NXP Linux 4.9.11_1.0.0 release.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the PHYTEC phyBOARD-Mira with i.MX 6QuadPlus with NAND.
It is based on the phyBOARD-Mira with i.MX 6Quad/Dual and supports the
same interfaces.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Stefan Lengfeld <s.lengfeld@phytec.de>
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the PHYTEC phyBOARD-Mira Low-Cost Rapid Development Kit
with i.MX 6DualLight/Solo with NAND.

Following interfaces are supported:
- 100 MBit Ethernet
- USB Host
- RS232
- HDMI
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the PHYTEC phyBOARD-Mira Rapid Development Kit with
i.MX 6Quad/Dual with eMMC or NAND.

Following interfaces are supported:
- Gigabit Ethernet
- USB Host
- CAN
- RS232
- PCIe
- LVDS
- HDMI
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds basic support for PHYTEC phyBOARD-Mira as carrier board
for PHYTEC phyCORE-i.MX 6.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds basic support for PHYTEC phyCORE-i.MX 6 SOM with i.MX
6Quad/Dual or i.MX 6DualLight/Solo.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX 7D SDB has a MPL3115 Pressure sensor.
Add support for this sensor, which is included in the trivial i2c devices
and according to the bindings documentation, just need a compatible field
and an address.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX 6UL EVK has a MAG3110 Magnetometer sensor in its base board.
Add support for this sensor, which is included in the trivial i2c devices
and according to the bindings documentation, just need a compatible field
and an address.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The system has an external watchdog in the environment processor
so the internal watchdog is of no use.

Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: cphealy@gmail.com
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove unnecessary clocks for cpu-freq driver to
avoid confusion.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ads7846 is connected to SPI chip select 0, so pass the unit address
accordingly to fix the following build warning with W=1:

arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dtb: Warning (unit_address_vs_reg): Node /soc/aipi@10000000/cspi@1000e000/ads7846 has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Move i2cmux node from soc node to root node.

i2cmux node does not have any register properties and thus shouldn't be
placed on the bus.

This fixes the following build warnings with W=1:

arch/arm/boot/dts/imx28-cfa10049.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbx@80040000/i2cmux missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pass unit address and reg to IOMUX node to fix the following build
warning with W=1:

arch/arm/boot/dts/imx28-apx4devkit.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/mmc2-sck-cfg-apx4 missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pass unit address and reg to IOMUX node to fix the following build
warning with W=1:

arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/tx28-edt-ft5x06-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/tx28-flexcan-xcvr-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/tx28-lcdif-23bit missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/tx28-lcdif-ctrl missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/tx28-mac0-gpio-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/tx28-pca9554-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/spi-gpiogrp missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/tx28-tsc2007-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/tx28-usbphy0-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/tx28-usbphy1-pins missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pass unit address and reg to IOMUX node to fix the following build
warning with W=1:

arch/arm/boot/dts/imx28-apf28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/gpmi-status-cfg missing or empty reg/ranges property
arch/arm/boot/dts/imx28-apf28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/mmc0-cd-cfg missing or empty reg/ranges property
arch/arm/boot/dts/imx28-apf28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/mmc0-sck-cfg missing or empty reg/ranges property
arch/arm/boot/dts/imx28-apf28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/mmc1-cd-cfg missing or empty reg/ranges property
arch/arm/boot/dts/imx28-apf28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/mmc1-sck-cfg missing or empty reg/ranges property
arch/arm/boot/dts/imx28-apf28.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/mmc2-cd-cfg missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>