- 25 Aug, 2023 1 commit
-
-
Russell Currey authored
fail_iommu_setup() registers the fail_iommu_bus_notifier struct to both PCI and VIO buses. struct notifier_block is a linked list node, so this causes any notifiers later registered to either bus type to also be registered to the other since they share the same node. This causes issues in (at least) the vgaarb code, which registers a notifier for PCI buses. pci_notify() ends up being called on a vio device, converted with to_pci_dev() even though it's not a PCI device, and finally makes a bad access in vga_arbiter_add_pci_device() as discovered with KASAN: BUG: KASAN: slab-out-of-bounds in vga_arbiter_add_pci_device+0x60/0xe00 Read of size 4 at addr c000000264c26fdc by task swapper/0/1 Call Trace: dump_stack_lvl+0x1bc/0x2b8 (unreliable) print_report+0x3f4/0xc60 kasan_report+0x244/0x698 __asan_load4+0xe8/0x250 vga_arbiter_add_pci_device+0x60/0xe00 pci_notify+0x88/0x444 notifier_call_chain+0x104/0x320 blocking_notifier_call_chain+0xa0/0x140 device_add+0xac8/0x1d30 device_register+0x58/0x80 vio_register_device_node+0x9ac/0xce0 vio_bus_scan_register_devices+0xc4/0x13c __machine_initcall_pseries_vio_device_init+0x94/0xf0 do_one_initcall+0x12c/0xaa8 kernel_init_freeable+0xa48/0xba8 kernel_init+0x64/0x400 ret_from_kernel_thread+0x5c/0x64 Fix this by creating separate notifier_block structs for each bus type. Fixes: d6b9a81b ("powerpc: IOMMU fault injection") Reported-by:
Nageswara R Sastry <rnsastry@linux.ibm.com> Signed-off-by:
Russell Currey <ruscur@russell.cc> Tested-by:
Andrew Donnellan <ajd@linux.ibm.com> [mpe: Add #ifdef to fix CONFIG_IBMVIO=n build] Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230322035322.328709-1-ruscur@russell.cc
-
- 24 Aug, 2023 16 commits
-
-
Liang He authored
In mpc5xxx_fwnode_get_bus_frequency(), we should add fwnode_handle_put() when break out of the iteration fwnode_for_each_parent_node() as it will automatically increase and decrease the refcounter. Fixes: de06fba6 ("powerpc/mpc5xxx: Switch mpc5xxx_get_bus_frequency() to use fwnode") Signed-off-by:
Liang He <windhl@126.com> Signed-off-by:
-
Joel Stanley authored
In 5.10 commit 5e84dd54 ("powerpc/configs/skiroot: Enable some more hardening options") set SLUB_DEBUG_ON. When 5.14 came around, commit 79270291 ("slub: force on no_hash_pointers when slub_debug is enabled") print all the pointers when SLUB_DEBUG_ON is set. This was fine, but in 5.12 commit 5ead723a ("lib/vsprintf: no_hash_pointers prints all addresses as unhashed") added the warning at boot. Disable SLAB_DEBUG_ON as we don't want the nasty warning. We have CONFIG_EXPERT so SLAB_DEBUG is enabled. We do lose the settings in DEBUG_DEFAULT_FLAGS, but it's not clear that these should have been always-on anyway. Signed-off-by:
Joel Stanley <joel@jms.id.au> Signed-off-by:
-
Nicholas Piggin authored
When JUMP_LABEL=n, the tracepoint refcount test in the pre-call stores the refcount value to the stack, so the same value can be used for the post-call (presumably to avoid racing with the value concurrently changing). On little-endian (ELFv2) that might have just worked by luck, because 32(r1) is STK_PARAM(R3) there and so the value save gets clobbered by the tracing code when it's non-zero, but fortunately r3 is the hcall number and 0 is an invalid hcall number so it should get clobbered by another non-zero value. In any case, commit cc1adb5f ("powerpc/pseries: Use jump labels for hcall tracepoints") removed the code that actually used the value stored, so now it's just dead code. It's fragile to be storing to the stack like this, and confusing. Better remove it. Signed-off-by:
Nicholas Piggin <npiggin@gmail.com> Signed-off-by:
-
Nicholas Piggin authored
With JUMP_LABEL=n, hcall_tracepoint_refcount's address is being tested instead of its value. This results in the tracing slowpath always being taken unnecessarily. Fixes: 9a10ccb2 ("powerpc/pseries: move hcall_tracepoint_refcount out of .toc") Signed-off-by:
-
Krzysztof Kozlowski authored
Add missing whitespace between node name/label and opening {. Signed-off-by:Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Jialin Zhang authored
PCI core API pci_dev_id() can be used to get the BDF number for a pci device. We don't need to compose it mannually. Use pci_dev_id() to simplify the code a little bit. Signed-off-by:
Jialin Zhang <zhangjialin11@huawei.com> Signed-off-by:
-
Michael Ellerman authored
Currently the -mtune options are set in the Makefile, depending on what the compiler supports. One downside of doing it that way is that the chosen -mtune option is not recorded in the .config. Another downside is that if there's ever a need to do more complicated logic to calculate the correct option, that gets messy in the Makefile. So move the determination of which -mtune option to use into Kconfig logic. Signed-off-by:
-
Michael Ellerman authored
Clang reports: arch/powerpc/platforms/powermac/feature.c:137:19: error: unused function 'simple_feature_tweak' It's only used inside the #ifndef CONFIG_PPC64 block, so move it in there to fix the warning. While at it drop the inline, the compiler will decide whether it should be inlined or not. Reported-by:
kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202308181501.AR5HMDWC-lkp@intel.com/Signed-off-by:
-
Russell Currey authored
lppaca_shared_proc() takes a pointer to the lppaca which is typically accessed through get_lppaca(). With DEBUG_PREEMPT enabled, this leads to checking if preemption is enabled, for example: BUG: using smp_processor_id() in preemptible [00000000] code: grep/10693 caller is lparcfg_data+0x408/0x19a0 CPU: 4 PID: 10693 Comm: grep Not tainted 6.5.0-rc3 #2 Call Trace: dump_stack_lvl+0x154/0x200 (unreliable) check_preemption_disabled+0x214/0x220 lparcfg_data+0x408/0x19a0 ... This isn't actually a problem however, as it does not matter which lppaca is accessed, the shared proc state will be the same. vcpudispatch_stats_procfs_init() already works around this by disabling preemption, but the lparcfg code does not, erroring any time /proc/powerpc/lparcfg is accessed with DEBUG_PREEMPT enabled. Instead of disabling preemption on the caller side, rework lppaca_shared_proc() to not take a pointer and instead directly access the lppaca, bypassing any potential preemption checks. Fixes: f13c13a0 ("powerpc: Stop using non-architected shared_proc field in lppaca") Signed-off-by: -
Michael Ellerman authored
By adding a forward declaration for struct lppaca we can untangle paca.h and lppaca.h. Also move get_lppaca() into lppaca.h for consistency. Add includes of lppaca.h to some files that need it. Signed-off-by:
-
Michael Ellerman authored
Consolidate the two prototypes for hcall_vphn() into vphn.h. Signed-off-by:
-
Michael Ellerman authored
These don't have any particularly good reason to belong in lppaca.h, move them into their own header. Signed-off-by:
-
Michael Ellerman authored
Clang warns: drivers/misc/cxl/native.c:272:20: error: unused function 'detach_spa' [-Werror,-Wunused-function] It was created as part of some refactoring in commit 05155772 ("cxl: Allocate and release the SPA with the AFU"), but has never been called in its current form. Drop it. Acked-by:
-
Michael Ellerman authored
The only callers of zalloc_maybe_bootmem() are PCI setup routines. These used to be called early during boot before slab setup, and also during runtime due to hotplug. But commit 5537fcb3 ("powerpc/pci: Add ppc_md.discover_phbs()") moved the boot-time calls later, after slab setup, meaning there's no longer any need for zalloc_maybe_bootmem(), kzalloc() can be used in all cases. Reviewed-by:
Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by:
-
Michael Ellerman authored
Use the newly added struct opal_prd_msg in some other functions that operate on opal_prd messages, rather than using other types. Signed-off-by:
-
Michael Ellerman authored
As reported by Mahesh & Aneesh, opal_prd_msg_notifier() triggers a FORTIFY_SOURCE warning: memcpy: detected field-spanning write (size 32) of single field "&item->msg" at arch/powerpc/platforms/powernv/opal-prd.c:355 (size 4) WARNING: CPU: 9 PID: 660 at arch/powerpc/platforms/powernv/opal-prd.c:355 opal_prd_msg_notifier+0x174/0x188 [opal_prd] NIP opal_prd_msg_notifier+0x174/0x188 [opal_prd] LR opal_prd_msg_notifier+0x170/0x188 [opal_prd] Call Trace: opal_prd_msg_notifier+0x170/0x188 [opal_prd] (unreliable) notifier_call_chain+0xc0/0x1b0 atomic_notifier_call_chain+0x2c/0x40 opal_message_notify+0xf4/0x2c0 This happens because the copy is targeting item->msg, which is only 4 bytes in size, even though the enclosing item was allocated with extra space following the msg. To fix the warning define struct opal_prd_msg with a union of the header and a flex array, and have the memcpy target the flex array. Reported-by:"Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com> Reported-by:
Mahesh Salgaonkar <mahesh@linux.ibm.com> Tested-by:
-
- 23 Aug, 2023 3 commits
-
-
Christophe Leroy authored
powerpc/85xx: Mark some functions static and add missing includes to fix no previous prototype error corenet{32/64}_smp_defconfig leads to: CC arch/powerpc/sysdev/ehv_pic.o arch/powerpc/sysdev/ehv_pic.c:45:6: error: no previous prototype for 'ehv_pic_unmask_irq' [-Werror=missing-prototypes] 45 | void ehv_pic_unmask_irq(struct irq_data *d) | ^~~~~~~~~~~~~~~~~~ arch/powerpc/sysdev/ehv_pic.c:52:6: error: no previous prototype for 'ehv_pic_mask_irq' [-Werror=missing-prototypes] 52 | void ehv_pic_mask_irq(struct irq_data *d) | ^~~~~~~~~~~~~~~~ arch/powerpc/sysdev/ehv_pic.c:59:6: error: no previous prototype for 'ehv_pic_end_irq' [-Werror=missing-prototypes] 59 | void ehv_pic_end_irq(struct irq_data *d) | ^~~~~~~~~~~~~~~ arch/powerpc/sysdev/ehv_pic.c:66:6: error: no previous prototype for 'ehv_pic_direct_end_irq' [-Werror=missing-prototypes] 66 | void ehv_pic_direct_end_irq(struct irq_data *d) | ^~~~~~~~~~~~~~~~~~~~~~ arch/powerpc/sysdev/ehv_pic.c:71:5: error: no previous prototype for 'ehv_pic_set_affinity' [-Werror=missing-prototypes] 71 | int ehv_pic_set_affinity(struct irq_data *d, const struct cpumask *dest, | ^~~~~~~~~~~~~~~~~~~~ arch/powerpc/sysdev/ehv_pic.c:112:5: error: no previous prototype for 'ehv_pic_set_irq_type' [-Werror=missing-prototypes] 112 | int ehv_pic_set_irq_type(struct irq_data *d, unsigned int flow_type) | ^~~~~~~~~~~~~~~~~~~~ CC arch/powerpc/sysdev/fsl_rio.o arch/powerpc/sysdev/fsl_rio.c:102:5: error: no previous prototype for 'fsl_rio_mcheck_exception' [-Werror=missing-prototypes] 102 | int fsl_rio_mcheck_exception(struct pt_regs *regs) | ^~~~~~~~~~~~~~~~~~~~~~~~ arch/powerpc/sysdev/fsl_rio.c:306:5: error: no previous prototype for 'fsl_map_inb_mem' [-Werror=missing-prototypes] 306 | int fsl_map_inb_mem(struct rio_mport *mport, dma_addr_t lstart, | ^~~~~~~~~~~~~~~ arch/powerpc/sysdev/fsl_rio.c:357:6: error: no previous prototype for 'fsl_unmap_inb_mem' [-Werror=missing-prototypes] 357 | void fsl_unmap_inb_mem(struct rio_mport *mport, dma_addr_t lstart) | ^~~~~~~~~~~~~~~~~ arch/powerpc/sysdev/fsl_rio.c:445:5: error: no previous prototype for 'fsl_rio_setup' [-Werror=missing-prototypes] 445 | int fsl_rio_setup(struct platform_device *dev) | ^~~~~~~~~~~~~ CC arch/powerpc/sysdev/fsl_rmu.o arch/powerpc/sysdev/fsl_rmu.c:362:6: error: no previous prototype for 'msg_unit_error_handler' [-Werror=missing-prototypes] 362 | void msg_unit_error_handler(void) | ^~~~~~~~~~~~~~~~~~~~~~ CC arch/powerpc/platforms/85xx/corenet_generic.o arch/powerpc/platforms/85xx/corenet_generic.c:33:13: error: no previous prototype for 'corenet_gen_pic_init' [-Werror=missing-prototypes] 33 | void __init corenet_gen_pic_init(void) | ^~~~~~~~~~~~~~~~~~~~ arch/powerpc/platforms/85xx/corenet_generic.c:51:13: error: no previous prototype for 'corenet_gen_setup_arch' [-Werror=missing-prototypes] 51 | void __init corenet_gen_setup_arch(void) | ^~~~~~~~~~~~~~~~~~~~~~ arch/powerpc/platforms/85xx/corenet_generic.c:104:12: error: no previous prototype for 'corenet_gen_publish_devices' [-Werror=missing-prototypes] 104 | int __init corenet_gen_publish_devices(void) | ^~~~~~~~~~~~~~~~~~~~~~~~~~~ CC arch/powerpc/platforms/85xx/qemu_e500.o arch/powerpc/platforms/85xx/qemu_e500.c:28:13: error: no previous prototype for 'qemu_e500_pic_init' [-Werror=missing-prototypes] 28 | void __init qemu_e500_pic_init(void) | ^~~~~~~~~~~~~~~~~~ CC arch/powerpc/kernel/pmc.o arch/powerpc/kernel/pmc.c:78:6: error: no previous prototype for 'power4_enable_pmcs' [-Werror=missing-prototypes] 78 | void power4_enable_pmcs(void) | ^~~~~~~~~~~~~~~~~~ Signed-off-by: -
Christophe Leroy authored
asm/percpu.h includes asm/paca.h which needs struct tlb_core_data which is defined in mmu-e500.h asm/percpu.h is included from asm/mmu.h in a #ifdef CONFIG_E500 before the inclusion of mmu-e500.h To fix that, move the inclusion of asm/percpu.h into mmu-e500.h after the definition of struct tlb_core_data Reported-by:
-
Immad Mir authored
The debugfs_create_dir returns ERR_PTR incase of an error and the correct way of checking it by using the IS_ERR inline function, and not the simple null comparision. This patch fixes this. Suggested-by:
Ivan Orlov <ivan.orlov0322@gmail.com> Signed-off-by:
Immad Mir <mirimmad17@gmail.com> Signed-off-by:
-
- 21 Aug, 2023 16 commits
-
-
Naveen N Rao authored
GCC v13.1 updated support for -fpatchable-function-entry on ppc64le to emit nops after the local entry point, rather than before it. This allows us to use this in the kernel for ftrace purposes. A new script is added under arch/powerpc/tools/ to help detect if nops are emitted after the function local entry point, or before the global entry point. With -fpatchable-function-entry, we no longer have the profiling instructions generated at function entry, so we only need to validate the presence of two nops at the ftrace location in ftrace_init_nop(). We patch the preceding instruction with 'mflr r0' to match the -mprofile-kernel ABI for subsequent ftrace use. This changes the profiling instructions used on ppc32. The default -pg option emits an additional 'stw' instruction after 'mflr r0' and before the branch to _mcount 'bl _mcount'. This is very similar to the original -mprofile-kernel implementation on ppc64le, where an additional 'std' instruction was used to save LR to its save location in the caller's stackframe. Subsequently, this additional store was removed in later compiler versions for performance reasons. The same reasons apply for ppc32 so we only patch in a 'mflr r0'. Signed-off-by:
Naveen N Rao <naveen@kernel.org> Reviewed-by:
-
Naveen N Rao authored
Implement ftrace_replace_code() to consolidate logic from the different ftrace patching routines: ftrace_make_nop(), ftrace_make_call() and ftrace_modify_call(). Note that ftrace_make_call() is still required primarily to handle patching modules during their load time. The other two routines should no longer be called. This lays the groundwork to enable better control in patching ftrace locations, including the ability to nop-out preceding profiling instructions when ftrace is disabled. Signed-off-by:
-
Naveen N Rao authored
ftrace_create_branch_inst() is clearer about its intent than ftrace_call_replace(). Signed-off-by:
-
Naveen N Rao authored
Now that we validate the ftrace location during initialization in ftrace_init_nop(), we can simplify ftrace_modify_call() to patch-in the updated branch instruction without worrying about the instructions surrounding the ftrace location. Note that we continue to ensure we have the expected branch instruction at the ftrace location before patching it with the updated branch destination. Signed-off-by:
-
Naveen N Rao authored
Now that we validate the ftrace location during initialization in ftrace_init_nop(), we can simplify ftrace_make_call() to replace the nop without worrying about the instructions surrounding the ftrace location. Note that we continue to ensure that we have a nop at the ftrace location before patching it. Signed-off-by:
-
Naveen N Rao authored
Now that we validate the ftrace location during initialization in ftrace_init_nop(), we can simplify ftrace_make_nop() to patch-in the nop without worrying about the instructions surrounding the ftrace location. Note that we continue to ensure that we have a bl to ftrace_[regs_]caller at the ftrace location before nop-ing it out. Signed-off-by:
-
Naveen N Rao authored
Currently, we validate instructions around the ftrace location every time we have to enable/disable ftrace. Introduce ftrace_init_nop() to instead perform all the validation during ftrace initialization. This allows us to simply patch the necessary instructions during enabling/disabling ftrace. Signed-off-by:
-
Naveen N Rao authored
Commit 67361cf8 ("powerpc/ftrace: Handle large kernel configs") added ftrace support for ppc64 kernel images with a text section larger than 32MB. The patch did two things: 1. Add stubs at the end of .text to branch into ftrace_[regs_]caller for functions that were out of branch range. 2. Re-purpose linker-generated long branches to _mcount to instead branch to ftrace_[regs_]caller. Before that, we only supported kernel .text up to ~32MB. With the above, we now support up to ~96MB: - The first 32MB of kernel text can branch directly into ftrace_[regs_]caller since that symbol is usually at the beginning. - The modified long_branch from (2) above is used by the next 32MB of kernel text. - The next 32MB of kernel text can use the stub at the end of text to branch back to ftrace_[regs_]caller. While re-purposing the long branch works in practice, it still restricts ftrace to kernel text up to ~96MB. The stub at the end of kernel text from (1) already enables us to extend ftrace support for kernel text up to 64MB, which fulfils the original requirement. Further, once we switch to -fpatchable-function-entry, there will not be a long branch that we can use. Stop re-purposing the linker-generated long branches for ftrace to simplify the code. If there are good reasons to support ftrace on kernels beyond 64MB, we can consider adding support by using -fpatchable-function-entry. Signed-off-by:
-
Naveen N Rao authored
Split up ftrace_modify_code() into a few helpers for future use. Also update error messages accordingly. Signed-off-by:
-
Naveen N Rao authored
ftrace_low.S has just the _mcount stub and return_to_handler(). Merge this back into ftrace_mprofile.S and ftrace_64_pg.S to keep all ftrace code together, and to allow those to evolve independently. ftrace_mprofile.S is also not an entirely accurate name since this also holds ppc32 code. This will be all the more incorrect once support for -fpatchable-function-entry is added. Rename files here to more accurately describe the code: - ftrace_mprofile.S is renamed to ftrace_entry.S - ftrace_pg.c is renamed to ftrace_64_pg.c - ftrace_64_pg.S is rename to ftrace_64_pg_entry.S Signed-off-by:
-
Naveen N Rao authored
Commit 67361cf8 ("powerpc/ftrace: Handle large kernel configs") added ftrace support for ppc64 kernel images with a text section larger than 32MB. The approach itself isn't specific to ppc64, so extend the same to also work on ppc32. While at it, reduce the space reserved for the stub from 64 bytes to 32 bytes since the different stub variants are all less than 8 instructions. To reduce use of #ifdef, a stub implementation is provided for kernel_toc_address() and -SZ_2G is cast to 'long long' to prevent errors on ppc32. Signed-off-by:
-
Naveen N Rao authored
Instead of keying off DYNAMIC_FTRACE_WITH_REGS, use FTRACE_REGS_ADDR to identify the proper ftrace trampoline address to use. Signed-off-by:
-
Naveen N Rao authored
Since we now support DYNAMIC_FTRACE_WITH_ARGS across ppc32 and ppc64 ELFv2, we can simplify function_graph tracer support code in ftrace.c Signed-off-by:
-
Naveen N Rao authored
ELFv1 support is deprecated and on the way out. Pre -mprofile-kernel ftrace support (-pg only) is very limited and is retained primarily for clang builds. It won't be necessary once clang lands support for -fpatchable-function-entry. Copy the existing ftrace code supporting these into ftrace_pg.c. ftrace.c can then be refactored and enhanced with a focus on ppc32 and ppc64 ELFv2. Signed-off-by:
-
Naveen N Rao authored
.ftrace.tramp section is not used for any purpose. This code was added all the way back in the original commit introducing support for dynamic ftrace on ppc64 modules. Remove it. Signed-off-by:
-
Naveen N Rao authored
The minimum level of gcc supported for building the kernel is v5.1. v5.x releases of gcc emitted a three instruction sequence for -mprofile-kernel: mflr r0 std r0, 16(r1) bl _mcount It is only with the v6.x releases that gcc started emitting the two instruction sequence for -mprofile-kernel, omitting the second store instruction. With the older three instruction sequence, the actual ftrace location can be the 5th instruction into a function. Update the allowed offset for ftrace location from 12 to 16 to accommodate the same. Cc: stable@vger.kernel.org Fixes: 7af82ff9 ("powerpc/ftrace: Ignore weak functions") Signed-off-by:
-
- 18 Aug, 2023 4 commits
-
-
Christophe Leroy authored
CC arch/powerpc/perf/core-fsl-emb.o arch/powerpc/perf/core-fsl-emb.c:675:6: error: no previous prototype for 'hw_perf_event_setup' [-Werror=missing-prototypes] 675 | void hw_perf_event_setup(int cpu) | ^~~~~~~~~~~~~~~~~~~ Looks like fsl_emb was completely missed by commit 3f6da390 ("perf: Rework and fix the arch CPU-hotplug hooks") So, apply same changes as commit 3f6da390 ("perf: Rework and fix the arch CPU-hotplug hooks") then commit 57ecde42 ("powerpc/perf: Convert book3s notifier to state machine callbacks") While at it, also fix following error: arch/powerpc/perf/core-fsl-emb.c: In function 'perf_event_interrupt': arch/powerpc/perf/core-fsl-emb.c:648:13: error: variable 'found' set but not used [-Werror=unused-but-set-variable] 648 | int found = 0; | ^~~~~ Fixes: 3f6da390 ("perf: Rework and fix the arch CPU-hotplug hooks") Signed-off-by: -
Mahesh Salgaonkar authored
When certain PHB HW failure causes pHyp to recover PHB, it marks the PE state as temporarily unavailable until recovery is complete. This also triggers an EEH handler in Linux which needs to notify drivers, and perform recovery. But before notifying the driver about the PCI error it uses get_adapter_status()->rpaphp_get_sensor_state()->rtas_call(get-sensor-state) operation of the hotplug_slot to determine if the slot contains a device or not. If the slot is empty, the recovery is skipped entirely. eeh_event_handler() ->eeh_handle_normal_event() ->eeh_slot_presence_check() ->get_adapter_status() ->rpaphp_get_sensor_state() ->rtas_get_sensor() ->rtas_call(get-sensor-state) However on certain PHB failures, the RTAS call rtas_call(get-sensor-state) returns extended busy error (9902) until PHB is recovered by pHyp. Once PHB is recovered, the rtas_call(get-sensor-state) returns success with correct presence status. The RTAS call interface rtas_get_sensor() loops over the RTAS call on extended delay return code (9902) until the return value is either success (0) or error (-1). This causes the EEH handler to get stuck for ~6 seconds before it could notify that the PCI error has been detected and stop any active operations. Hence with running I/O traffic, during this 6 seconds, the network driver continues its operation and hits a timeout (netdev watchdog). ------------ [52732.244731] DEBUG: ibm_read_slot_reset_state2() [52732.244762] DEBUG: ret = 0, rets[0]=5, rets[1]=1, rets[2]=4000, rets[3]=> [52732.244798] DEBUG: in eeh_slot_presence_check [52732.244804] DEBUG: error state check [52732.244807] DEBUG: Is slot hotpluggable [52732.244810] DEBUG: hotpluggable ops ? [52732.244953] DEBUG: Calling ops->get_adapter_status [52732.244958] DEBUG: calling rpaphp_get_sensor_state [52736.564262] ------------[ cut here ]------------ [52736.564299] NETDEV WATCHDOG: enP64p1s0f3 (tg3): transmit queue 0 timed o> [52736.564324] WARNING: CPU: 1442 PID: 0 at net/sched/sch_generic.c:478 dev> [...] [52736.564505] NIP [c000000000c32368] dev_watchdog+0x438/0x440 [52736.564513] LR [c000000000c32364] dev_watchdog+0x434/0x440 ------------ On timeouts, network driver starts dumping debug information to console (e.g bnx2 driver calls bnx2x_panic_dump()), and go into recovery path while pHyp is still recovering the PHB. As part of recovery, the driver tries to reset the device and it keeps failing since every PCI read/write returns ff's. And when EEH recovery kicks-in, the driver is unable to recover the device. This impacts the ssh connection and leads to the system being inaccessible. To get the NIC working again it needs a reboot or re-assign the I/O adapter from HMC. [ 9531.168587] EEH: Beginning: 'slot_reset' [ 9531.168601] PCI 0013:01:00.0#10000: EEH: Invoking bnx2x->slot_reset() [...] [ 9614.110094] bnx2x: [bnx2x_func_stop:9129(enP19p1s0f0)]FUNC_STOP ramrod failed. Running a dry transaction [ 9614.110300] bnx2x: [bnx2x_igu_int_disable:902(enP19p1s0f0)]BUG! Proper val not read from IGU! [ 9629.178067] bnx2x: [bnx2x_fw_command:3055(enP19p1s0f0)]FW failed to respond! [ 9629.178085] bnx2x 0013:01:00.0 enP19p1s0f0: bc 7.10.4 [ 9629.178091] bnx2x: [bnx2x_fw_dump_lvl:789(enP19p1s0f0)]Cannot dump MCP info while in PCI error [ 9644.241813] bnx2x: [bnx2x_io_slot_reset:14245(enP19p1s0f0)]IO slot reset --> driver unload [...] [ 9644.241819] PCI 0013:01:00.0#10000: EEH: bnx2x driver reports: 'disconnect' [ 9644.241823] PCI 0013:01:00.1#10000: EEH: Invoking bnx2x->slot_reset() [ 9644.241827] bnx2x: [bnx2x_io_slot_reset:14229(enP19p1s0f1)]IO slot reset initializing... [ 9644.241916] bnx2x 0013:01:00.1: enabling device (0140 -> 0142) [ 9644.258604] bnx2x: [bnx2x_io_slot_reset:14245(enP19p1s0f1)]IO slot reset --> driver unload [ 9644.258612] PCI 0013:01:00.1#10000: EEH: bnx2x driver reports: 'disconnect' [ 9644.258615] EEH: Finished:'slot_reset' with aggregate recovery state:'disconnect' [ 9644.258620] EEH: Unable to recover from failure from PHB#13-PE#10000. [ 9644.261811] EEH: Beginning: 'error_detected(permanent failure)' [...] [ 9644.261823] EEH: Finished:'error_detected(permanent failure)' Hence, it becomes important to inform driver about the PCI error detection as early as possible, so that driver is aware of PCI error and waits for EEH handler's next action for successful recovery. Current implementation uses rtas_get_sensor() API which blocks the slot check state until RTAS call returns success. To avoid this, fix the PCI hotplug driver (rpaphp) to return an error (-EBUSY) if the slot presence state can not be detected immediately while PE is in EEH recovery state. Change rpaphp_get_sensor_state() to invoke rtas_call(get-sensor-state) directly only if the respective PE is in EEH recovery state, and take actions based on RTAS return status. This way EEH handler will not be blocked on rpaphp_get_sensor_state() and can immediately notify driver about the PCI error and stop any active operations. In normal cases (non-EEH case) rpaphp_get_sensor_state() will continue to invoke rtas_get_sensor() as it was earlier with no change in existing behavior. Signed-off-by:Nathan Lynch <nathanl@linux.ibm.com> Acked-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Mahesh Salgaonkar authored
Also, #define descriptive names for common rtas return codes and use it instead of numeric values. Signed-off-by:
-
Vaibhav Jain authored
This patch enables config option GENERIC_IDLE_POLL_SETUP for arch powerpc. This adds support for kernel param 'nohlt'. Powerpc kernel also supports another kernel boot-time param called 'powersave' which can also be used to disable all cpu idle-states and forces CPU to an idle-loop similar to what cpu_idle_poll() does. This patch however makes powerpc kernel-parameters better aligned to the generic boot-time parameters. Signed-off-by:
Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by:
-
