When we leave host-mode because the id-pin is no longer connected to
ground, the 5v boost converter is normally still on, so we will see
Vbus, but it is not from a charger (normally) so the charger-type
detection will fail.

This commit silences the cht_wc_extcon_get_charger() false-positive
errors when we're leaving host mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

Disable the 5v boost converter on probe in case it was left on by
the BIOS, this fixes 2 problems:

1) This gets seen by the external battery charger as a valid Vbus
   supply and it then tries to feed Vsys from this creating a
   feedback loop which causes aprox. 300 mA extra battery drain
   (and unless we drive the external-charger-disable pin high it
   also tries to charge the battery causing even more feedback).
2) This gets seen by the pwrsrc block as a SDP USB Vbus supply

Since the external battery charger has its own 5v boost converter
which does not have these issues, we simply turn the separate
external 5v boost converter off and leave it off entirely.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

This patch removes the porting compatibility for switch class
because there is no any usage and requirement of swich class
over a couple of years.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

Add a driver for charger detection / control on the Intel Cherrytrail
Whiskey Cove PMIC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

The USB cable state can change during suspend/resume
so be sure to check and update the extcon state.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

We must check for ID/VBUS changes during resume irrespective
of whether our device wakeup is enabled or not.

Without this we seem to be missing ID/VBUS events after
system suspend/resume.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

Whether the USB port as a wakeup source should be determined by user,
but not enabled by default.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

As the HPDET can't be aborted mid way through we should not allow any new
insertion to be processed until the previous HPDET has finished. It is very
unlikely but with low enough debounce settings you could start a new HPDET
before the old one has completed, which results in an erroneous reading.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

The extcon core already provides the extcon_register_notifier() function
in order to register the notifier block which is used to monitor
the state change for the specific external connector such as EXTCON_USB,
EXTCON_USB_HOST and so on. The extcon consumer uses the this function.

The extcon consumer might need to monitor the all supported external
connectors from the extcon device. In this case, The extcon consumer
should have each notifier_block structure for each external connector.

This patch adds the new extcon_register_notifier_all() function
that extcon consumer is able to monitor the state change of all
supported external connectors by using only one notifier_block structure.

- List of new added functions:
int extcon_register_notifier_all(struct extcon_dev *edev,
			struct notifier_block *nb);
int extcon_unregister_notifier_all(struct extcon_dev *edev,
			struct notifier_block *nb);
int devm_extcon_register_notifier_all(struct device *dev,
			struct extcon_dev *edev, struct notifier_block *nb);
void devm_extcon_unregister_notifier_all(struct device *dev,
			struct extcon_dev *edev, struct notifier_block *nb);
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>

The commit 942c7924 introduced a check for ACPI handle for the
device that never appears on any ACPI-enabled platform so far. It seems
a confusion with extcon-intel-int3496 which does support ACPI-enabled
platforms.

Revert commit 942c7924 to avoid any confusion in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

Pull char/misc driver fixes from Greg KH:
 "A smattering of different small fixes for some random driver
  subsystems. Nothing all that major, just resolutions for reported
  issues and bugs.

  All have been in linux-next with no reported issues"

* tag 'char-misc-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
  extcon: int3496: Set the id pin to direction-input if necessary
  extcon: int3496: Use gpiod_get instead of gpiod_get_index
  extcon: int3496: Add dependency on X86 as it's Intel specific
  extcon: int3496: Add GPIO ACPI mapping table
  extcon: int3496: Rename GPIO pins in accordance with binding
  vmw_vmci: handle the return value from pci_alloc_irq_vectors correctly
  ppdev: fix registering same device name
  parport: fix attempt to write duplicate procfiles
  auxdisplay: img-ascii-lcd: add missing sentinel entry in img_ascii_lcd_matches
  Drivers: hv: vmbus: Don't leak memory when a channel is rescinded
  Drivers: hv: vmbus: Don't leak channel ids
  Drivers: hv: util: don't forget to init host_ts.lock
  Drivers: hv: util: move waiting for release to hv_utils_transport itself
  vmbus: remove hv_event_tasklet_disable/enable
  vmbus: use rcu for per-cpu channel list
  mei: don't wait for os version message reply
  mei: fix deadlock on mei reset
  intel_th: pci: Add Gemini Lake support
  intel_th: pci: Add Denverton SOC support
  intel_th: Don't leak module refcount on failure to activate
  ...

Merge tag 'driver-core-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fix from Greg KH:
 "Here is a single kernfs fix for 4.11-rc4 that resolves a reported
  issue.

  It has been in linux-next with no reported issues"

* tag 'driver-core-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  kernfs: Check KERNFS_HAS_RELEASE before calling kernfs_release_file()

Pull tty/serial driver fixes from Greg KH:
 "Here are some tty and serial driver fixes for 4.11-rc4.

  One of these fix a long-standing issue in the ldisc code that was
  found by Dmitry Vyukov with his great fuzzing work. The other fixes
  resolve other reported issues, and there is one revert of a patch in
  4.11-rc1 that wasn't correct.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: fix data race in tty_ldisc_ref_wait()
  tty: don't panic on OOM in tty_set_ldisc()
  Revert "tty: serial: pl011: add ttyAMA for matching pl011 console"
  tty: acpi/spcr: QDF2400 E44 checks for wrong OEM revision
  serial: 8250_dw: Fix breakage when HAVE_CLK=n
  serial: 8250_dw: Honor clk_round_rate errors in dw8250_set_termios

Pull IIO driver fixes from Greg KH:
 "Here are some small IIO driver fixes for 4.11-rc4 that resolve a
  number of tiny reported issues. All of these have been in linux-next
  for a while with no reported issues"

* tag 'staging-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: imu: st_lsm6dsx: fix FIFO_CTRL2 overwrite during watermark configuration
  iio: adc: ti_am335x_adc: fix fifo overrun recovery
  iio: sw-device: Fix config group initialization
  iio: magnetometer: ak8974: remove incorrect __exit markups
  iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3

Pull USB/PHY fixes from Greg KH:
 "Here are a number of small USB and PHY driver fixes for 4.11-rc4.

  Nothing major here, just an bunch of small fixes, and a handfull of
  good fixes from Johan for devices with crazy descriptors. There are a
  few new device ids in here as well.

  All of these have been in linux-next with no reported issues"

* tag 'usb-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
  usb: gadget: f_hid: fix: Don't access hidg->req without spinlock held
  usb: gadget: udc: remove pointer dereference after free
  usb: gadget: f_uvc: Sanity check wMaxPacketSize for SuperSpeed
  usb: gadget: f_uvc: Fix SuperSpeed companion descriptor's wBytesPerInterval
  usb: gadget: acm: fix endianness in notifications
  usb: dwc3: gadget: delay unmap of bounced requests
  USB: serial: qcserial: add Dell DW5811e
  usb: hub: Fix crash after failure to read BOS descriptor
  ACM gadget: fix endianness in notifications
  USB: usbtmc: fix probe error path
  USB: usbtmc: add missing endpoint sanity check
  USB: serial: option: add Quectel UC15, UC20, EC21, and EC25 modems
  usb: musb: fix possible spinlock deadlock
  usb: musb: dsps: fix iounmap in error and exit paths
  usb: musb: cppi41: don't check early-TX-interrupt for Isoch transfer
  usb-core: Add LINEAR_FRAME_INTR_BINTERVAL USB quirk
  uwb: i1480-dfu: fix NULL-deref at probe
  uwb: hwa-rc: fix NULL-deref at probe
  USB: wusbcore: fix NULL-deref at probe
  USB: uss720: fix NULL-deref at probe
  ...

Pull more powerpc fixes from Michael Ellerman:
 "These are all pretty minor. The fix for idle wakeup would be a bad bug
  but has not been observed in practice.

  The update to the gcc-plugins docs was Cc'ed to Kees and Jon, Kees
  OK'ed it going via powerpc and I didn't hear from Jon.

   - cxl: Route eeh events to all slices for pci_channel_io_perm_failure state

   - powerpc/64s: Fix idle wakeup potential to clobber registers

   - Revert "powerpc/64: Disable use of radix under a hypervisor"

   - gcc-plugins: update architecture list in documentation

  Thanks to: Andrew Donnellan, Nicholas Piggin, Paul Mackerras, Vaibhav
  Jain"

* tag 'powerpc-4.11-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  gcc-plugins: update architecture list in documentation
  Revert "powerpc/64: Disable use of radix under a hypervisor"
  powerpc/64s: Fix idle wakeup potential to clobber registers
  cxl: Route eeh events to all slices for pci_channel_io_perm_failure state

Pull ext4 fixes from Ted Ts'o:
 "Fix a memory leak on an error path, and two races when modifying
  inodes relating to the inline_data and metadata checksum features"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix two spelling nits
  ext4: lock the xattr block before checksuming it
  jbd2: don't leak memory if setting up journal fails
  ext4: mark inode dirty after converting inline directory

Pull fscrypto fixes from Ted Ts'o:
 "A code cleanup and bugfix for fs/crypto"

* tag 'fscrypt-for-linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt:
  fscrypt: eliminate ->prepare_context() operation
  fscrypt: remove broken support for detecting keyring key revocation

Merge tag 'hwmon-for-linus-v4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:

 - bug fixes in asus_atk0110, it87 and max31790 drivers

 - added missing API definition to hwmon core

* tag 'hwmon-for-linus-v4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (asus_atk0110) fix uninitialized data access
  hwmon: Add missing HWMON_T_ALARM
  hwmon: (it87) Avoid registering the same chip on both SIO addresses
  hwmon: (max31790) Set correct PWM value

Pull rdma fixes from Doug Ledford:
 "This has been a slow -rc cycle for the RDMA subsystem. We really
  haven't had a lot of rc fixes come in. This pull request is the first
  of this entire rc cycle and it has all of the suitable fixes so far
  and it's still only about 20 patches. The fix for the minor breakage
  cause by the dma mapping patchset is in here, as well as a couple
  other potential oops fixes, but the rest is more minor.

  Summary:

   - fix for dma_ops change in this kernel, resolving the s390, powerpc,
     and IOMMU operation

   - a few other oops fixes

   - the rest are all minor fixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  IB/qib: fix false-postive maybe-uninitialized warning
  RDMA/iser: Fix possible mr leak on device removal event
  IB/device: Convert ib-comp-wq to be CPU-bound
  IB/cq: Don't process more than the given budget
  IB/rxe: increment msn only when completing a request
  uapi: fix rdma/mlx5-abi.h userspace compilation errors
  IB/core: Restore I/O MMU, s390 and powerpc support
  IB/rxe: Update documentation link
  RDMA/ocrdma: fix a type issue in ocrdma_put_pd_num()
  IB/rxe: double free on error
  RDMA/vmw_pvrdma: Activate device on ethernet link up
  RDMA/vmw_pvrdma: Dont hardcode QP header page
  RDMA/vmw_pvrdma: Cleanup unused variables
  infiniband: Fix alignment of mmap cookies to support VIPT caching
  IB/core: Protect against self-requeue of a cq work item
  i40iw: Receive netdev events post INET_NOTIFIER state

Pull audit fix from Paul Moore:
 "We've got an audit fix, and unfortunately it is big.

  While I'm not excited that we need to be sending you something this
  large during the -rcX phase, it does fix some very real, and very
  tangled, problems relating to locking, backlog queues, and the audit
  daemon connection.

  This code has passed our testsuite without problem and it has held up
  to my ad-hoc stress tests (arguably better than the existing code),
  please consider pulling this as fix for the next v4.11-rcX tag"

* 'stable-4.11' of git://git.infradead.org/users/pcmoore/audit:
  audit: fix auditd/kernel connection state tracking

Signed-off-by: Theodore Ts'o <tytso@mit.edu>

We must lock the xattr block before calculating or verifying the
checksum in order to avoid spurious checksum failures.

https://bugzilla.kernel.org/show_bug.cgi?id=193661Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org

Pull clk fixes from Stephen Boyd:
 "A handful of Sunxi and Rockchip clk driver fixes and a core framework
  one where we need to copy a string because we can't guarantee it isn't
  freed sometime later"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: sunxi-ng: fix recalc_rate formula of NKMP clocks
  clk: sunxi-ng: Fix div/mult settings for osc12M on A64
  clk: rockchip: Make uartpll a child of the gpll on rk3036
  clk: rockchip: add "," to mux_pll_src_apll_dpll_gpll_usb480m_p on rk3036
  clk: core: Copy connection id
  dt-bindings: arm: update Armada CP110 system controller binding
  clk: sunxi-ng: sun6i: Fix enable bit offset for hdmi-ddc module clock
  clk: sunxi: ccu-sun5i needs nkmp
  clk: sunxi-ng: mp: Adjust parent rate for pre-dividers

aarch64-linux-gcc-7 complains about code it doesn't fully understand:

drivers/infiniband/hw/qib/qib_iba7322.c: In function 'qib_7322_txchk_change':
include/asm-generic/bitops/non-atomic.h:105:35: error: 'shadow' may be used uninitialized in this function [-Werror=maybe-uninitialized]

The code is right, and despite trying hard, I could not come up with a version
that I liked better than just adding a fake initialization here to shut up the
warning.

Fixes: f931551b ("IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When the rdma device is removed, we must cleanup all
the rdma resources within the DEVICE_REMOVAL event
handler to let the device teardown gracefully. When
this happens with live I/O, some memory regions are
occupied. Thus, track them too and dereg all the mr's.

We are safe with mr access by iscsi_iser_cleanup_task.
Reported-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This workqueue is used by our storage target mode ULPs
via the new CQ API. Recent observations when working
with very high-end flash storage devices reveal that
UNBOUND workqueue threads can migrate between cpu cores
and even numa nodes (although some numa locality is accounted
for).

While this attribute can be useful in some workloads,
it does not fit in very nicely with the normal
run-to-completion model we usually use in our target-mode
ULPs and the block-mq irq<->cpu affinity facilities.

The whole block-mq concept is that the completion will
land on the same cpu where the submission was performed.
The fact that our submitter thread is migrating cpus
can break this locality.

We assume that as a target mode ULP, we will serve multiple
initiators/clients and we can spread the load enough without
having to use unbound kworkers.

Also, while we're at it, expose this workqueue via sysfs which
is harmless and can be useful for debug.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>--
Signed-off-by: Doug Ledford <dledford@redhat.com>

The caller might not want this overhead.
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

According to C9-147, MSN should only be incremented when the last packet of
a multi packet request has been received.

"Logically, the requester associates a sequential Send Sequence Number
(SSN) with each WQE posted to the send queue. The SSN bears a one-
to-one relationship to the MSN returned by the responder in each re-
sponse packet. Therefore, when the requester receives a response, it in-
terprets the MSN as representing the SSN of the most recent request
completed by the responder to determine which send WQE(s) can be
completed."

Fixes: 8700e3e7 ("Soft RoCE driver")
Signed-off-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Consistently use types from linux/types.h to fix the following
rdma/mlx5-abi.h userspace compilation errors:

/usr/include/rdma/mlx5-abi.h:69:25: error: 'u64' undeclared here (not in a function)
  MLX5_LIB_CAP_4K_UAR = (u64)1 << 0,
/usr/include/rdma/mlx5-abi.h:69:29: error: expected ',' or '}' before numeric constant
  MLX5_LIB_CAP_4K_UAR = (u64)1 << 0,

Include <linux/if_ether.h> to fix the following rdma/mlx5-abi.h
userspace compilation error:

/usr/include/rdma/mlx5-abi.h:286:12: error: 'ETH_ALEN' undeclared here (not in a function)
  __u8 dmac[ETH_ALEN];
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Avoid that the following error message is reported on the console
while loading an RDMA driver with I/O MMU support enabled:

DMAR: Allocating domain for mlx5_0 failed

Ensure that DMA mapping operations that use to_pci_dev() to
access to struct pci_dev see the correct PCI device. E.g. the s390
and powerpc DMA mapping operations use to_pci_dev() even with I/O
MMU support disabled.

This patch preserves the following changes of the DMA mapping updates
patch series:
- Introduction of dma_virt_ops.
- Removal of ib_device.dma_ops.
- Removal of struct ib_dma_mapping_ops.
- Removal of an if-statement from each ib_dma_*() operation.
- IB HW drivers no longer set dma_device directly.
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reported-by: Parav Pandit <parav@mellanox.com>
Fixes: commit 99db9494 ("IB/core: Remove ib_device.dma_device")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: parav@mellanox.com
Tested-by: parav@mellanox.com
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

All Soft-RoCE (rxe) is handled now in rdma-core user space library,
so the documentation. The patch below updates the documentation
link to that new location.
Reported-by: Josh Beavers <josh.beavers@gmail.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

We want to return zero on success or negative error codes.  The type
should be int and not u8.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

"goto err;" has it's own kfree_skb() call so it's a double free.  We
only need to free on the "goto exit;" path.

Fixes: 8700e3e7 ("Soft RoCE driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Restore device state when ethernet link changes to active.
Acked-by: George Zhang <georgezhang@vmware.com>
Acked-by: Jorgen Hansen <jhansen@vmware.com>
Acked-by: Bryan Tan <bryantan@vmware.com>
Signed-off-by: Aditya Sarwade <asarwade@vmware.com>
Signed-off-by: Adit Ranadive <aditr@vmware.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Moved the header page count to a macro.
Reported-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Aditya Sarwade <asarwade@vmware.com>
Tested-by: Andrew Boyer <andrew.boyer@dell.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Removed the unused nreq and redundant index variables.
Moved hardcoded async and cq ring pages number to macro.
Reported-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Aditya Sarwade <asarwade@vmware.com>
Tested-by: Andrew Boyer <andrew.boyer@dell.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Pull VFIO fix from Alex Williamson:
 "Rework sanity check for mdev driver group notifier de-registration
  (Alex Williamson)"

* tag 'vfio-v4.11-rc4' of git://github.com/awilliam/linux-vfio:
  vfio: Rework group release notifier warning