Overhaul the AFS callback handling by the following means:

 (1) Don't give up callback promises on vnodes that we are no longer using,
     rather let them just expire on the server or let the server break
     them.  This is actually more efficient for the server as the callback
     lookup is expensive if there are lots of extant callbacks.

 (2) Only give up the callback promises we have from a server when the
     server record is destroyed.  Then we can just give up *all* the
     callback promises on it in one go.

 (3) Servers can end up being shared between cells if cells are aliased, so
     don't add all the vnodes being backed by a particular server into a
     big FID-indexed tree on that server as there may be duplicates.

     Instead have each volume instance (~= superblock) register an interest
     in a server as it starts to make use of it and use this to allow the
     processor for callbacks from the server to find the superblock and
     thence the inode corresponding to the FID being broken by means of
     ilookup_nowait().

 (4) Rather than iterating over the entire callback list when a mass-break
     comes in from the server, maintain a counter of mass-breaks in
     afs_server (cb_seq) and make afs_validate() check it against the copy
     in afs_vnode.

     It would be nice not to have to take a read_lock whilst doing this,
     but that's tricky without using RCU.

 (5) Save a ref on the fileserver we're using for a call in the afs_call
     struct so that we can access its cb_s_break during call decoding.

 (6) Write-lock around callback and status storage in a vnode and read-lock
     around getattr so that we don't see the status mid-update.

This has the following consequences:

 (1) Data invalidation isn't seen until someone calls afs_validate() on a
     vnode.  Unfortunately, we need to use a key to query the server, but
     getting one from a background thread is tricky without caching loads
     of keys all over the place.

 (2) Mass invalidation isn't seen until someone calls afs_validate().

 (3) Callback breaking is going to hit the inode_hash_lock quite a bit.
     Could this be replaced with rcu_read_lock() since inodes are destroyed
     under RCU conditions.
Signed-off-by: David Howells <dhowells@redhat.com>

Rename the server member of struct afs_call to cm_server as we're only
going to be using it for incoming calls for the Cache Manager service.
This makes it easier to differentiate from the pointer to the target server
for the client, which will point to a different structure to allow for
callback handling.
Signed-off-by: David Howells <dhowells@redhat.com>

In AFS's encoding of a UUID, the eight 'char' fields are all signed, so
represent them with __s8 rather than __u8.  This makes the compiler
sign-extend them correctly when XDR-encoding them.
Signed-off-by: David Howells <dhowells@redhat.com>

The handler for the CB.ProbeUuid operation in the cache manager is
implemented, but isn't listed in the switch-statement of operation
selection, so won't be used.  Fix this by adding it.
Signed-off-by: David Howells <dhowells@redhat.com>

If call->ret_reply0 is set, return call->reply[0] on success.  Change the
return type of afs_make_call() to long so that this can be passed back
without bit loss and then cast to a pointer if required.
Signed-off-by: David Howells <dhowells@redhat.com>

Condense struct afs_call's reply anchor members - reply{,2,3,4} - into an
array.
Signed-off-by: David Howells <dhowells@redhat.com>

The AFS abort code space is shared across all services, so there's no need
for separate abort_to_error translators for each service.

Consolidate them into a single function and remove the function pointers
for them.
Signed-off-by: David Howells <dhowells@redhat.com>

Allow VL server specifications to be given IPv6 addresses as well as IPv4
addresses, for example as:

	echo add foo.org 1111:2222:3333:0:4444:5555:6666:7777 >/proc/fs/afs/cells

Note that ':' is the expected separator for separating IPv4 addresses, but
if a ',' is detected or no '.' is detected in the string, the delimiter is
switched to ','.

This also works with DNS AFSDB or SRV record strings fetched by upcall from
userspace.
Signed-off-by: David Howells <dhowells@redhat.com>

Keep and pass sockaddr_rxrpc addresses around rather than keeping and
passing in_addr addresses to allow for the use of IPv6 and non-standard
port numbers in future.

This also allows the port and service_id fields to be removed from the
afs_call struct.
Signed-off-by: David Howells <dhowells@redhat.com>

Update the cache index structure in the following ways:

 (1) Don't use the volume name followed by the volume type as levels in the
     cache index.  Volumes can be renamed.  Use the volume ID instead.

 (2) Don't store the VLDB data for a volume in the tree.  If the volume
     database should be cached locally, then it should be done in a separate
     tree.

 (3) Expand the volume ID stored in the cache to 64 bits.

 (4) Expand the file/vnode ID stored in the cache to 96 bits.

 (5) Increment the cache structure version number to 1.
Signed-off-by: David Howells <dhowells@redhat.com>

Add some protocol definitions, including max field lengths, flag defs, an
XDR-encoded UUID def, more VL operation IDs and more fileserver abort
codes.
Signed-off-by: David Howells <dhowells@redhat.com>

Push the network namespace pointer to more places in AFS, including the
afs_server structure (which doesn't hold a ref on the netns).

In particular, afs_put_cell() now takes requires a net ns parameter so that
it can safely alter the netns after decrementing the cell usage count - the
cell will be deallocated by a background thread after being cached for a
period, which means that it's not safe to access it after reducing its
usage count.
Signed-off-by: David Howells <dhowells@redhat.com>

Keep a reference to the cell in the superblock info structure in addition
to the volume and net pointers.  This will make it easier to clean up in a
future patch in which afs_put_volume() will need the cell pointer.

Whilst we're at it, make the cell and volume getting functions return a
pointer to the object got to make the call sites look neater.
Signed-off-by: David Howells <dhowells@redhat.com>

Fix server reaping and make sure it's all done before we start trying to
purge cells, given that servers currently pin cells.
Signed-off-by: David Howells <dhowells@redhat.com>

Close the rxrpc socket only after we've purged the server records (and also
cell and volume records which might refer to servers) so that we can give
up the callbacks on each server.
Signed-off-by: David Howells <dhowells@redhat.com>

Lay the groundwork for supporting network namespaces (netns) to the AFS
filesystem by moving various global features to a network-namespace struct
(afs_net) and providing an instance of this as a temporary global variable
that everything uses via accessor functions for the moment.

The following changes have been made:

 (1) Store the netns in the superblock info.  This will be obtained from
     the mounter's nsproxy on a manual mount and inherited from the parent
     superblock on an automount.

 (2) The cell list is made per-netns.  It can be viewed through
     /proc/net/afs/cells and also be modified by writing commands to that
     file.

 (3) The local workstation cell is set per-ns in /proc/net/afs/rootcell.
     This is unset by default.

 (4) The 'rootcell' module parameter, which sets a cell and VL server list
     modifies the init net namespace, thereby allowing an AFS root fs to be
     theoretically used.

 (5) The volume location lists and the file lock manager are made
     per-netns.

 (6) The AF_RXRPC socket and associated I/O bits are made per-ns.

The various workqueues remain global for the moment.

Changes still to be made:

 (1) /proc/fs/afs/ should be moved to /proc/net/afs/ and a symlink emplaced
     from the old name.

 (2) A per-netns subsys needs to be registered for AFS into which it can
     store its per-netns data.

 (3) Rather than the AF_RXRPC socket being opened on module init, it needs
     to be opened on the creation of a superblock in that netns.

 (4) The socket needs to be closed when the last superblock using it is
     destroyed and all outstanding client calls on it have been completed.
     This prevents a reference loop on the namespace.

 (5) It is possible that several namespaces will want to use AFS, in which
     case each one will need its own UDP port.  These can either be set
     through /proc/net/afs/cm_port or the kernel can pick one at random.
     The init_ns gets 7001 by default.

Other issues that need resolving:

 (1) The DNS keyring needs net-namespacing.

 (2) Where do upcalls go (eg. DNS request-key upcall)?

 (3) Need something like open_socket_in_file_ns() syscall so that AFS
     command line tools attempting to operate on an AFS file/volume have
     their RPC calls go to the right place.
Signed-off-by: David Howells <dhowells@redhat.com>

Make wait_on_atomic_t() pass the TASK_* mode onto its action function as an
extra argument and make it 'unsigned int throughout.

Also, consolidate a bunch of identical action functions into a default
function that can do the appropriate thing for the mode.

Also, change the argument name in the bit_wait*() function declarations to
reflect the fact that it's the mode and not the bit number.

[Peter Z gives this a grudging ACK, but thinks that the whole atomic_t wait
should be done differently, though he's not immediately sure as to how]
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
cc: Ingo Molnar <mingo@kernel.org>

These AFS patches need the timer_reduce() patch from timers/core.
Signed-off-by: David Howells <dhowells@redhat.com>

Xin Long says:

====================
net: improve the process of redirect and toobig for ipv6 tunnels

Now let's say there are 3 kinds of icmp packets to process for tunnels,
toobig(needfrag), redirect, others, their process should be:

 - toobig(needfrag)
   update the lower dst's pmtu by route cache, also update sk dst's pmtu
   if possible, or it will be fine if sk dst pmtu will get updated on tx
   path.

 - redirect
   update the lower dst's gw by route cache and return, no need to send
   this redirect packet to user sk.

 - others
   send the packet to user's sk, or it will also be fine to use err_count
   to count it and report fail link on tx path.

All ipv4 tunnels basically follow this while some of ipv6 tunnels are
doing in different ways, like ip6gre and ip6_tunnels update tnl dev's
mtu instead of updating lower dst pmtu, no redirect process on their
err_handlers, which doesn't make any sense and even causes performance
problems.

This patchset is to improve the process of redirect and toobig for ip6gre
ip4ip6, ip6ip6 tunnels, as in ipv4 tunnels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to remove some useless codes of redirect and fix some
indents on ip4ip6 and ip6ip6's err_handlers.

Note that redirect icmp packet is already processed in ip6_tnl_err,
the old redirect codes in ip4ip6_err actually never worked even
before this patch. Besides, there's no need to send redirect to
user's sk, it's for lower dst, so just remove it in this patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same improvement in "ip6_gre: process toobig in a better way"
is needed by ip4ip6 and ip6ip6 as well.

Note that ip4ip6 and ip6ip6 will also update sk dst pmtu in their
err_handlers. Like I said before, gre6 could not do this as it's
inner proto is not certain. But for all of them, sk dst pmtu will
be updated in tx path if in need.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same process for redirect in "ip6_gre: add the process for redirect
in ip6gre_err" is needed by ip4ip6 and ip6ip6 as well.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now ip6gre processes toobig icmp packet by setting gre dev's mtu in
ip6gre_err, which would cause few things not good:

  - It couldn't set mtu with dev_set_mtu due to it's not in user context,
    which causes route cache and idev->cnf.mtu6 not to be updated.

  - It has to update sk dst pmtu in tx path according to gredev->mtu for
    ip6gre, while it updates pmtu again according to lower dst pmtu in
    ip6_tnl_xmit.

  - To change dev->mtu by toobig icmp packet is not a good idea, it should
    only work on pmtu.

This patch is to process toobig by updating the lower dst's pmtu, as later
sk dst pmtu will be updated in ip6_tnl_xmit, the same way as in ip4gre.

Note that gre dev's mtu will not be updated any more, it doesn't make any
sense to change dev's mtu after receiving a toobig packet.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add redirect icmp packet process for ip6gre by
calling ip6_redirect() in ip6gre_err(), as in vti6_err.

Prior to this patch, there's even no route cache generated after
receiving redirect.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In xmit process, the variables are set many times. In fact,
it is enough for these variables to be set once.
After a long time test, the throughput performance is better
than before.

CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Samuel Ortiz says:

====================
NFC 4.15 pull request

This is the NFC pull request for 4.15. We have:

- A new netlink command for explicitly deactivating NFC targets
- i2c constification for all NFC drivers
- One NFC device allocation error path fix
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Andy Zhou says:

====================
Openvswitch meter action

This patch series is the first attempt to add openvswitch
meter support. We have previously experimented with adding
metering support in nftables. However 1) It was not clear
how to expose a named nftables object cleanly, and 2)
the logic that implements metering is quite small, < 100 lines
of code.

With those two observations, it seems cleaner to add meter
support in the openvswitch module directly.

---

    v1(RFC)->v2:  remove unused code improve locking
		  and other review comments
    v2 -> v3:     rebase
    v3 -> v4:     fix undefined "__udivdi3" references on 32 bit builds.
                  use div_u64() instead.
    v4 -> v5:     rebase
====================
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implements OVS kernel meter action support.
Signed-off-by: Andy Zhou <azhou@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

OVS kernel datapath so far does not support Openflow meter action.
This is the first stab at adding kernel datapath meter support.
This implementation supports only drop band type.
Signed-off-by: Andy Zhou <azhou@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Later patches will invoke get_dp() outside of datapath.c. Export it.
Signed-off-by: Andy Zhou <azhou@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Meter has its own netlink family. Define netlink messages and attributes
for communicating with the user space programs.
Signed-off-by: Andy Zhou <azhou@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: b53: Support prepended Broadcom tags

This patch series adds support for prepended 4-bytes Broadcom tags that we
already support. This type of tag will typically be used when interfaced to
a SoC like BCM58xx (NorthStar Plus) which supports a Flow Accelerator (WIP).
In that case, we need to support a slightly different tagging format.

The first patch does a bit of re-factoring and passes a port index to
the get_tag_protocol() function since at least two different drivers need
that type of information (mt7530, b53) to support tagging or not.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On BCM58xx devices (Northstar Plus), there is an accelerator attached to
port 8 which would only work if we use prepended Broadcom tags. Resolve
that difference in our get_tag_protocol() function by setting the
appropriate tagging protocol in that case. We need to change
b53_brcm_hdr_setup() a little bit now since we can deal with two types
of Broadcom tags.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new type: DSA_TAG_PROTO_PREPEND which allows us to support for the
4-bytes Broadcom tag that we already support, but in a format where it
is pre-pended to the packet instead of located between the MAC SA and
the Ethertyper (DSA_TAG_PROTO_BRCM).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for supporting the same Broadcom tag format, but instead
of inserted between the MAC SA and EtherType, prepended to the Ethernet
frame, restructure the code a little bit to make that possible and take
an offset parameter.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

A number of drivers want to check whether the configured CPU port is a
possible configuration for enabling tagging, pass down the CPU port
number so they verify that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

gcc-4.4.4 (at lest) has issues with initializers and anonymous unions:

net/sched/sch_red.c: In function 'red_dump_offload':
net/sched/sch_red.c:282: error: unknown field 'stats' specified in initializer
net/sched/sch_red.c:282: warning: initialization makes integer from pointer without a cast
net/sched/sch_red.c:283: error: unknown field 'stats' specified in initializer
net/sched/sch_red.c:283: warning: initialization makes integer from pointer without a cast
net/sched/sch_red.c: In function 'red_dump_stats':
net/sched/sch_red.c:352: error: unknown field 'xstats' specified in initializer
net/sched/sch_red.c:352: warning: initialization makes integer from pointer without a cast

Work around this.

Fixes: 602f3baf ("net_sch: red: Add offload ability to RED qdisc")
Cc: Nogah Frankel <nogahf@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Simon Horman <simon.horman@netronome.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since Mellanox focus is on newer adapters, we would like to have the
ability to disable the support for old gen2 adapters.

This can be done by turning off the MLX4_CORE_GEN2 Kconfig flag.
We keep it turned on by default.
Signed-off-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The way people generally use netlink_dump is that they fill in the skb
as much as possible, breaking when nla_put returns an error. Then, they
get called again and start filling out the next skb, and again, and so
forth. The mechanism at work here is the ability for the iterative
dumping function to detect when the skb is filled up and not fill it
past the brim, waiting for a fresh skb for the rest of the data.

However, if the attributes are small and nicely packed, it is possible
that a dump callback function successfully fills in attributes until the
skb is of size 4080 (libmnl's default page-sized receive buffer size).
The dump function completes, satisfied, and then, if it happens to be
that this is actually the last skb, and no further ones are to be sent,
then netlink_dump will add on the NLMSG_DONE part:

  nlh = nlmsg_put_answer(skb, cb, NLMSG_DONE, sizeof(len), NLM_F_MULTI);

It is very important that netlink_dump does this, of course. However, in
this example, that call to nlmsg_put_answer will fail, because the
previous filling by the dump function did not leave it enough room. And
how could it possibly have done so? All of the nla_put variety of
functions simply check to see if the skb has enough tailroom,
independent of the context it is in.

In order to keep the important assumptions of all netlink dump users, it
is therefore important to give them an skb that has this end part of the
tail already reserved, so that the call to nlmsg_put_answer does not
fail. Otherwise, library authors are forced to find some bizarre sized
receive buffer that has a large modulo relative to the common sizes of
messages received, which is ugly and buggy.

This patch thus saves the NLMSG_DONE for an additional message, for the
case that things are dangerously close to the brim. This requires
keeping track of the errno from ->dump() across calls.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dave Taht says:

====================
netem: add nsec scheduling and slot feature

This patch series converts netem away from the old "ticks" interface and
userspace API, and adds support for a new "slot" feature intended to
emulate bursty macs such as WiFi and LTE better.

Changes since v2:
Use u64 for packet_len_sched_time()
Use simpler max(time_to_send,q->slot.slot_next)

Changes since v1:
Always pass new nanosecond APIs to userspace
====================
Signed-off-by: David S. Miller <davem@davemloft.net>