For DEVICE_VERSION_V2, the hardware supports enable tx and rx
promiscuous separately. But tx or rx promiscuous is active for
unicast, multicast and broadcast promiscuous simultaneously.
To support traffics between functions belong to the same port,
we always enable tx promiscuous for broadcast promiscuous, so
tx promiscuous for unicast and multicast promiscuous is also
enabled.

For DEVICE_VERSION_V3, the hardware decouples the above
relationship. Tx unicast promiscuous, rx unicast promiscuous,
tx multicast promiscuous, rx multicast promiscuous, tx broadcast
promiscuous and rx broadcast promiscuous can be enabled separately.

So add support for the new promiscuous command.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

These warnings become somewhat more informative when they include the
MTU value that could not be set and not just the errno.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20201205133944.10182-1-rasmus.villemoes@prevas.dkSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Saeed Mahameed says:

====================
mlx5-next auxbus support

This pull request is targeting net-next and rdma-next branches.

This series provides mlx5 support for auxiliary bus devices.

It starts with a merge commit of tag 'auxbus-5.11-rc1' from
gregkh/driver-core into mlx5-next, then the mlx5 patches that will convert
mlx5 ulp devices (netdev, rdma, vdpa) to use the proper auxbus
infrastructure instead of the internal mlx5 device and interface management
implementation, which Leon is deleting at the end of this patchset.

Link: https://lore.kernel.org/alsa-devel/20201026111849.1035786-1-leon@kernel.org/

Thanks to everyone for the joint effort !

* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
  RDMA/mlx5: Remove IB representors dead code
  net/mlx5: Simplify eswitch mode check
  net/mlx5: Delete custom device management logic
  RDMA/mlx5: Convert mlx5_ib to use auxiliary bus
  net/mlx5e: Connect ethernet part to auxiliary bus
  vdpa/mlx5: Connect mlx5_vdpa to auxiliary bus
  net/mlx5: Register mlx5 devices to auxiliary virtual bus
  vdpa/mlx5: Make hardware definitions visible to all mlx5 devices
  net/mlx5_core: Clean driver version and name
  net/mlx5: Properly convey driver version to firmware
  driver core: auxiliary bus: minor coding style tweaks
  driver core: auxiliary bus: make remove function return void
  driver core: auxiliary bus: move slab.h from include file
  Add auxiliary bus support
====================

Link: https://lore.kernel.org/r/20201207053349.402772-1-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

All usages of the definition MAX_MSIX_P_PORT were removed.
It's not in use anymore. Remove it.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Link: https://lore.kernel.org/r/20201206091254.12476-1-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

We can remove one of the ifdef blocks here, and instead of setting both
the xfrm hw_features and features flags, then unsetting the feature
flags if not in AB, wait to set the features flags if we're actually in AB
mode.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Link: https://lore.kernel.org/r/20201205174003.578267-1-jarod@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

We sometimes run into situations where a soft/hard reset of the adapter
takes a long time or fails to complete. Having additional messages that
include important adapter state info will hopefully help understand what
is happening, reduce the guess work and minimize requests to reproduce
problems with debug patches.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Link: https://lore.kernel.org/r/20201205022235.2414110-1-sukadev@linux.ibm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Julian Wiedmann says:

====================
s390/qeth: updates 2020-12-07

please apply the following patch series for qeth to netdev's net-next tree.

Some sysfs cleanups (with the prep work in ccwgroup acked by Heiko), and
a few improvements to the code that deals with async TX completion
notifications for IQD devices.

This also brings the missing patch from the previous net-next submission.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When qeth_qdio_handle_aob() frees dangling allocations in the notified
TX buffer, there are rare tear-down cases where
qeth_drain_output_queue() would later call qeth_clear_output_buffer()
for the same buffer - and thus end up walking the buffer a second time
to check for dangling kmem_cache allocations.

Luckily current code previously scrubs such a buffer, so
qeth_clear_output_buffer() would find buf->buffer->element[i].addr as
NULL and not do anything. But this is fragile, and we can easily improve
it by consistently clearing the ->is_header flag after freeing the
allocation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reuse the QETH_QDIO_BUF_EMPTY state to indicate that a TX buffer has
been completed with a QAOB notification, and may be cleaned up by
qeth_cleanup_handled_pending().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For TX buffers that require an additional async notification via QAOB, the
TX completion code can now manage all the necessary processing if the
notification has already occurred (or is occurring concurrently).

In such cases we can avoid replacing the metadata that is associated
with the buffer's slot on the ring, and just keep using the current one.

As qeth_clear_output_buffer() will also handle any kmem cache-allocated
memory that was mapped into the TX buffer, qeth_qdio_handle_aob()
doesn't need to worry about it.

While at it, also remove the unneeded forward declaration for
qeth_init_qdio_out_buf().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All qeth devices have a minimum set of sysfs attributes, and non-OSN
devices share a group of additional attributes. Depending on whether
the device is forced to use a specific discipline, the device_type then
specifies further attributes.

Shift the common attributes into dev->groups, so that the device_type
only contains the discipline-specific attributes. This avoids exposing
the common attributes to the disciplines, and nicely cleans up our
sysfs code.

While replacing the qeth_l*_*_device_attributes() helpers, switch from
sysfs_*_groups() to the more generic device_*_groups().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bus drivers have their own way of describing the sysfs attributes that
all devices on a bus should provide.
Switch ccwgroup_attr_groups over to use bus->dev_groups, and thus
free up dev->groups for usage by the ccwgroup device drivers.

While adjusting the attribute naming, use ATTRIBUTE_GROUPS() to get rid
of some boilerplate code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

INIT_LIST_HEAD() only needs to be called on actual list heads.
While at it clarify the naming of the field.
Suggested-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Misc updates

This patchset contains miscellaneous patches we gathered in our queue.
Some of them are dependencies of larger patchsets that I will submit
later this cycle.

Patches #1-#3 perform small non-functional changes in mlxsw.

Patch #4 adds more extended ack messages in mlxsw.

Patch #5 adds devlink parameters documentation for mlxsw. To be extended
with more parameters this cycle.

Patches #6-#7 perform small changes in forwarding selftests
infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Turned out that mlxsw_sp_ipip_fib_entry_op_gre4() does not need to
figure out the IP address and virtual router id. Those are exactly
the same as in the fib_entry it is called for. So just use that and
reduce mlxsw_sp_ipip_fib_entry_op_gre4() function to only call
mlxsw_sp_ipip_fib_entry_op_gre4_rtdp() make the ipip decap op
code similar to nve.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The indicated version fixes an issue whereby the MOMTE register would by
default enable mirroring of ECN-marked traffic from all traffic classes,
once the ECN mirroring was configured. This fix is necessary for offload
of RED "ecn_mark" qevent.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suppresses the following coccinelle warning:

drivers/net/ethernet/mellanox/mlxsw/core_acl_flex_keys.c:139:3-7:
WARNING use flexible-array member instead
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suppresses the following coccinelle warning:

drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:18:15-19: WARNING use flexible-array member instead
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, mlxsw triggers the 'devlink:devlink_hwmsg' tracepoint
whenever a request is sent to the device and whenever a response is
received from it. However, the tracepoint is not triggered when an event
(e.g., port up / down) is received from the device.

Also trace EMAD events in order to log a more complete picture of all
the exchanged hardware messages.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that the reference count of a router interface (RIF) configured for
a LAG is incremented / decremented when ports join / leave the LAG. Use
the offload indication on routes configured on the RIF to understand if
it was created / destroyed.

The test fails without the previous patch.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case a router interface (RIF) is configured for a LAG, make sure its
configuration is applied on the new LAG member.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Delete dead code.
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>

Provide mlx5_core device instead of "priv" pointer while checking
eswith mode.
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>

After conversion to use auxiliary bus, all custom device management is
not needed anymore, delete it.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>

The conversion to auxiliary bus solves long standing issue with
existing mlx5_ib<->mlx5_core coupling. It required to have both
modules in initramfs if one of them needed for the boot.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>

Reuse auxiliary bus to perform device management of the
ethernet part of the mlx5 driver.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>

Change module registration logic to use auxiliary bus instead of custom
made mlx5 register interface.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>

Heiner Kallweit says:

====================
r8169: improve rtl_rx and NUM_RX_DESC handling

This series improves rtl_rx() and the handling of NUM_RX_DESC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After recent changes there's no need any longer to define NUM_RX_DESC
as an unsigned value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's no need to check min(budget, NUM_RX_DESC). At first budget
(NAPI_POLL_WEIGHT = 64) is less then NUM_RX_DESC (256).
And more important: Even in case of budget > NUM_RX_DESC we could
safely continue processing descriptors as long as they are owned by
the CPU. In addition replace rx_left with a normal counter variable,
this allows to simplify the code. Last but not least there's no need
any longer to pass the budget as an u32.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in the Kconfig help text. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201204194549.1153063-1-colin.king@canonical.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Simon Wunderlich says:

====================
This cleanup patchset includes the following patches:

 - bump version strings, by Simon Wunderlich

 - update include for min/max helpers, by Sven Eckelmann

 - add infrastructure and netlink functions for routing algo selection,
   by Sven Eckelmann (2 patches)

 - drop deprecated debugfs and sysfs support and obsoleted
   functionality, by Sven Eckelmann (3 patches)

 - drop unused include in fragmentation.c, by Simon Wunderlich

* tag 'batadv-next-pullrequest-20201204' of git://git.open-mesh.org/linux-merge:
  batman-adv: Drop unused soft-interface.h include in fragmentation.c
  batman-adv: Drop legacy code for auto deleting mesh interfaces
  batman-adv: Drop deprecated debugfs support
  batman-adv: Drop deprecated sysfs support
  batman-adv: Allow selection of routing algorithm over rtnetlink
  batman-adv: Prepare infrastructure for newlink settings
  batman-adv: Add new include for min/max helpers
  batman-adv: Start new development cycle
====================

Link: https://lore.kernel.org/r/20201204154631.21063-1-sw@simonwunderlich.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When CONFIG_OF is disabled, there is a harmless warning about
an unused variable:

enetc_pf.c: In function 'enetc_phylink_create':
enetc_pf.c:981:17: error: unused variable 'dev' [-Werror=unused-variable]

Slightly rearrange the code to pass around the of_node as a
function argument, which avoids the problem without hurting
readability.

Fixes: 71b77a7a ("enetc: Migrate to PHYLINK and PCS_LYNX")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201204120800.17193-1-claudiu.manoil@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The OpenCompute time card is an atomic clock along with
a GPS receiver that provides a Grandmaster clock source
for a PTP enabled network.

More information is available at http://www.timingcard.com/Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20201204035128.2219252-2-jonathan.lemon@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

implement the NCI 2.x initial sequence to support NCI 2.x NFCC.
Since NCI 2.0, CORE_RESET and CORE_INIT sequence have been changed.
If NFCEE supports NCI 2.x, then NCI 2.x initial sequence will work.

In NCI 1.0, Initial sequence and payloads are as below:
(DH)                     (NFCC)
 |  -- CORE_RESET_CMD --> |
 |  <-- CORE_RESET_RSP -- |
 |  -- CORE_INIT_CMD -->  |
 |  <-- CORE_INIT_RSP --  |
 CORE_RESET_RSP payloads are Status, NCI version, Configuration Status.
 CORE_INIT_CMD payloads are empty.
 CORE_INIT_RSP payloads are Status, NFCC Features,
    Number of Supported RF Interfaces, Supported RF Interface,
    Max Logical Connections, Max Routing table Size,
    Max Control Packet Payload Size, Max Size for Large Parameters,
    Manufacturer ID, Manufacturer Specific Information.

In NCI 2.0, Initial Sequence and Parameters are as below:
(DH)                     (NFCC)
 |  -- CORE_RESET_CMD --> |
 |  <-- CORE_RESET_RSP -- |
 |  <-- CORE_RESET_NTF -- |
 |  -- CORE_INIT_CMD -->  |
 |  <-- CORE_INIT_RSP --  |
 CORE_RESET_RSP payloads are Status.
 CORE_RESET_NTF payloads are Reset Trigger,
    Configuration Status, NCI Version, Manufacturer ID,
    Manufacturer Specific Information Length,
    Manufacturer Specific Information.
 CORE_INIT_CMD payloads are Feature1, Feature2.
 CORE_INIT_RSP payloads are Status, NFCC Features,
    Max Logical Connections, Max Routing Table Size,
    Max Control Packet Payload Size,
    Max Data Packet Payload Size of the Static HCI Connection,
    Number of Credits of the Static HCI Connection,
    Max NFC-V RF Frame Size, Number of Supported RF Interfaces,
    Supported RF Interfaces.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Link: https://lore.kernel.org/r/20201202223147.3472-1-bongsu.jeon@samsung.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Connect hosts H1 and H2 using two intermediate encapsulation routers
(LER1 and LER2). These routers encapsulate traffic from the hosts,
including the original Ethernet header, into MPLS.

Use ping to test reachability between H1 and H2.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://lore.kernel.org/r/625f5c1aafa3a8085f8d3e082d680a82e16ffbaa.1606918980.git.gnault@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The macro use will already have a semicolon.
Clean up escaped newlines.
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20201202163622.3733506-1-trix@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

We add the support to remove a specific node down with 128bit
node identifier, as an alternative to legacy 32-bit node address.

example:
$tipc peer remove identiy <1001002|16777777>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Link: https://lore.kernel.org/r/20201203035045.4564-1-hoang.h.le@dektech.com.auSigned-off-by: Jakub Kicinski <kuba@kernel.org>

There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code
should always use "flexible array members"[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9/process/deprecated.html#zero-length-and-one-element-arrays

Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Link: https://lore.kernel.org/r/20201204125601.24876-1-simon.horman@netronome.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If there isn't a proper NFC firmware image, Bootloader mode will be
skipped.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201203225257.2446-1-bongsu.jeon@samsung.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>