- 22 Jul, 2021 6 commits
-
-
Dongliang Mu authored
If dibusb_read_eeprom_byte fails, the mac address is not initialized. And nova_t_read_mac_address does not handle this failure, which leads to the uninit-value in dvb_usb_adapter_dvb_init. Fix this by handling the failure of dibusb_read_eeprom_byte. Reported-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com Fixes: 786baecf ("[media] dvb-usb: move it to drivers/media/usb/dvb-usb") Signed-off-by:
Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-
Sean Young authored
The s_learning_mode() function is called in response to the ioctl LIRC_SET_WIDEBAND_RECEIVER, so rename it to s_wideband_receiver(). Learning mode is when both the wideband receiver is turned on and carrier reports are enabled. Signed-off-by:
-
Sean Young authored
Any timeout larger than LIRC_VALUE_MASK cannot work for the lirc uapi. LIRC_VALUE_MASK is about 16 seconds which is more than enough. Signed-off-by:
-
Sean Young authored
When carrier reports are enabled, send them over loopback. Signed-off-by:
-
Sean Young authored
Make use of dynamic debug. Signed-off-by:
-
Sean Young authored
The LIRC_SET_TRANSMITTER_MASK ioctl should return the number of emitters if an invalid list was set. Cc: stable@vger.kernel.org Signed-off-by:
-
- 12 Jul, 2021 34 commits
-
-
Uwe Kleine-König authored
The Logilink VG0022A DVB-T2 stick has these three devices. So to enable support for this stick in the presence of MEDIA_SUBDRV_AUTOSELECT, let DVB_USB_AF9035 select the two other drivers. Signed-off-by:
Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by:
-
Uwe Kleine-König authored
If a sub device doesn't immediately bind after it was added, emit an error indication to the kernel log to help debugging. This happens for example if the needed driver isn't available at all. Signed-off-by:
-
lijian authored
break is not useful after a goto, so delete 'break' after 'goto'. Signed-off-by:
lijian <lijian@yulong.com> Signed-off-by:
-
Christophe JAILLET authored
If an error occurs after a successful 'regulator_enable()' call, 'regulator_disable()' must be called. Fix the error handling path of the probe accordingly. Fixes: cb496cd4 ("media: cxd2880-spi: Add optional vcc regulator") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
lijian authored
deleted the repeated word 'the' in the comments. Signed-off-by:
-
lijian authored
Change 'an' to 'on'. Signed-off-by:
-
lijian authored
Removed unnecessary 'return'. Signed-off-by:
-
Tomi Valkeinen authored
Add support for capturing embedded data from the sensor. The only difference with capturing pixel data and embedded data is that we need to ensure the PIX PROC is disabled for embedded data so that CAL doesn't repack the data. Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
-
Tomi Valkeinen authored
CAL RX has a single sink and a single source pad. To support multiple streams, we will have multiple source pads (up to 8, one for each CAL context). Change the driver to allow creating more source pads and change the code accordingly to handle multiple source pads. We still keep CAL_CAMERARX_NUM_SOURCE_PADS as 1, and the behavior is unchanged. Also rename CAL_CAMERARX_PAD_SOURCE to CAL_CAMERARX_PAD_FIRST_SOURCE to highlight that it's the first source. Signed-off-by:
-
Tomi Valkeinen authored
The following patches add multistream support and we will have multiple video devices using the same camerarx instances. Thus we need enable/disable refcounting for the camerarx. Signed-off-by:
-
Tomi Valkeinen authored
We don't have any locking in camerarx for the subdev ops. We have managed fine so far without locking, but in the future multiple video capture devices can use the same camerarx, and locking is a must. Add a mutex to protect the camerarx subdev ops. Some of the functions were slightly restructured to make lock handling cleaner. Signed-off-by:
-
Tomi Valkeinen authored
When starting streaming the driver currently programs the buffer address to the CAL base-address register and assigns the buffer pointer to ctx->dma.pending. This is not correct, as the buffer is not "pending", but active, and causes the first buffer to be needlessly written twice. Fix this by assigning the buffer pointer to ctx->dma.active. Signed-off-by:
-
Tomi Valkeinen authored
Somewhere along the way the context uninitialization has gone a bit odd: * We have cal_ctx_create() but no matching destroy call, but we still need to call cal_ctx_v4l2_cleanup() for each context. * We have cal_media_cleanup() which calls cal_ctx_v4l2_cleanup() for all contexts, but cal_media_init() is not where the contexts are created. * The order of uninit steps in cal_remove() is different than the error handling path in cal_probe(). * cal_probe()'s error handling calls cal_ctx_v4l2_cleanup() for each context, but also calls cal_media_clean(), doing the same context cleanup twice. So fix these, by introducing cal_ctx_destroy(), and using that in appropriate places instead of calling cal_ctx_v4l2_cleanup() in cal_media_clean(). Also use normal kzalloc (and kfree) instead of devm version as we anyway do manual cleanup for each context. Signed-off-by:
-
Tomi Valkeinen authored
Most of the driver has moved from ARRAY_SIZE(cal->phy) to cal->data->num_csi2_phy, but we have one place left in cal_remove. Also, checking for cal->phy[i] != NULL is not needed as we always have all the phys instantiated. Signed-off-by:
-
Tomi Valkeinen authored
The current driver only ever needs 2 DMA contexts (one per PHY), but we need to use more of the 8 contexts to add support for multiple streams. Change the code so that we allocate DMA contexts as needed, which at this time is 1 per PHY, but could be up to 8. Signed-off-by:
-
Tomi Valkeinen authored
struct cal_camerarx has fmtinfo field which is used to point to the current active input format. The only place where the field is used is cal_camerarx_get_ext_link_freq(). With multiple streams the whole concept of single input format is not valid anymore, so lets remove the field by looking up the format in cal_camerarx_get_ext_link_freq(), making it easier to handle the multistream-case in the following patches. Signed-off-by:
-
Tomi Valkeinen authored
CAL driver enumerates mbus codes in the connected subdev to create a list of supported formats reported to userspace, and initializes ctx->v_fmt and ctx->fmtinfo to one of those formats. This works fine for legacy mode, but is not correct for MC mode, and the list is not even used in MC mode. Fix this by adding a new function, cal_ctx_v4l2_init_mc_format, which only initializes ctx->v_fmt and ctx->fmtinfo to a default value. Signed-off-by:
-
Tomi Valkeinen authored
To make it more obvious if the function in question is dealing with media-controller API or the legacy API, rename legacy API functions to cal_legacy_*. Signed-off-by:
-
Tomi Valkeinen authored
Commit e5b6b07a ("media: v4l2: Extend VIDIOC_ENUM_FMT to support MC-centric devices") added support to enumerate formats based on mbus-code. Add this feature to cal driver. Signed-off-by:
-
Tomi Valkeinen authored
Fix a typo in a comment in cal_camerarx_sd_set_fmt(). Signed-off-by:
-
Tomi Valkeinen authored
cal_camerarx_sd_set_fmt() accepts any value for the format field, but there should be no reason to have any other value accepted than V4L2_FIELD_NONE. So set the field always to V4L2_FIELD_NONE. Signed-off-by:
-
Tomi Valkeinen authored
cal_async_notifier_complete() doesn't handle errors returned from cal_ctx_v4l2_register(). Add the error handling. Signed-off-by:
-
Tomi Valkeinen authored
In preparation for supporting multiple virtual channels and datatypes, add vc and datatype fields to cal_ctx, initialize them to the currently used values, and use those fields when writing to the register. Signed-off-by:
-
Tomi Valkeinen authored
I have not noticed any errors due to this, but the DMA configuration looks racy. Setting the DMA mode bitfield in CAL_WR_DMA_CTRL supposedly enables the DMA. However, the driver currently a) continues configuring the DMA after setting the mode, and b) enables the DMA interrupts only after setting the mode. This probably doesn't cause any issues as there should be no data coming in to the DMA yet, but it's still better to fix this. Add a new function, cal_ctx_wr_dma_enable(), to set the DMA mode field, and call that function only after the DMA config and the irq enabling has been done. Signed-off-by:
-
Tomi Valkeinen authored
We already have functions to reserve and release a pix proc unit, but we always reserve such and the code expects the pix proc unit to be used. Add a new field, 'use_pix_proc', to indicate if the pix prox unit has been reserved and should be used. Use the flag to skip programming pix proc unit when not needed. Note that we still always set the use_pix_proc flag to true. Signed-off-by:
-
Tomi Valkeinen authored
CAL has 4 pixel processing units but the units are not needed e.g. for metadata. As we could be capturing 4 pixel streams and 4 metadata streams, i.e. using 8 DMA contexts, we cannot assign a pixel processing unit to every DMA context. Instead we need to reserve a pixel processing unit only when needed. Add functions to reserve and release a pix proc unit, and use them in cal_ctx_prepare/unprepare. Note that for the time being we still always reserve a pix proc unit. Signed-off-by:
-
Tomi Valkeinen authored
Disable CSI2 context and pix proc in cal_ctx_stop() to ensure they are not used if the same context is used later on a different PHY or without pix proc. Signed-off-by:
-
Tomi Valkeinen authored
Asserting ComplexIO reset seems to affect the HW (ie. asserting reset will break an active capture), but the RESET_DONE bit never changes to "reset is ongoing" state. Thus we always get a timeout. Drop the wait, as it seems to achieve nothing. Signed-off-by:
-
Tomi Valkeinen authored
CAL driver currently ignores VC related errors. To help catch error conditions, enable all the VC error interrupts and handle them in the interrupt handler by printing an error. Signed-off-by:
-
Tomi Valkeinen authored
The macros related to CAL_CSI2_VC_IRQ can be handled better by having the VC number as a macro parameter. Note that the macros are not used anywhere yet, so no other changes are needed. Signed-off-by:
-
Tomi Valkeinen authored
CAL_HL_IRQ_MASK macro is used for both WDMA start and end status bits. For clarity, rename CAL_HL_IRQ_MASK macro to CAL_HL_IRQ_WDMA_END_MASK and CAL_HL_IRQ_WDMA_START_MASK. Signed-off-by:
-
Tomi Valkeinen authored
Rename cal_ctx->index to dma_ctx to clarify that the field refers to the DMA context number. Signed-off-by:
-
Tomi Valkeinen authored
CAL has 4 pixel processing contexts (PIX PROC) of which the driver currently uses pix proc 0 for PHY0, and pix proc 1 for PHY1 (as the driver supports only a single source per PHY). Add a pix_proc field to cal_ctx to allow us to use different pix proc contexts in the future Signed-off-by:
-
Tomi Valkeinen authored
CAL has 8 CSI2 contexts per PHY, which are used to tag the incoming data. The current driver only uses the first context, but we need to support all of them to implement multi-stream support. Add a csi2_ctx field to cal_ctx, which indicates which of the 8 CSI2 contexts is used for the particular cal_ctx. Also clean up the context register macros to take the CSI2 context number as a parameter. Note that before this patch the CSI2 context used for both PHYs was always 0. This patch always uses cal_ctx index number as the CSI2 context. There is no functional difference, but this approach will work also in the future when we use more than 1 CSI2 context per PHY. Signed-off-by:
-
