The PCI instructions may be used in IRQ context so scheduling is forbidden.
Use udelay and shorten the delay since we are now polling.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The dereference to 'zdev' should be moved below the NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Using kmem_cache_zalloc() instead of kmem_cache_alloc() and memset().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Add support for XOR instruction for use with X/K.

s390 JIT support for the new BPF_S_ALU_XOR_* instructions introduced
with 9e49e889 "filter: add XOR instruction for use with X/K".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Add support for MOD operation for s390's JIT.

Same as 280050cc "x86 bpf_jit: support MOD operation" for x86 which
adds JIT support for the generic new MOD operation introduced with
b6069a95 "filter: add MOD operation".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The check to whom a device is reserved is done by checking the path
state of the affected channel paths. If it turns out that one path is
flagged as reserved by someone else the whole device is marked as such.

However the meaning of the RESVD_ELSE bit is that the addressed device
is reserved to a different pathgroup (and not reserved to a different
LPAR). If we do this test on a path which is currently not a member of
the pathgroup we could erroneously mark the device as reserved to
someone else.

To fix this collect the reserved state for all potential members of the
pathgroup and only mark the device as reserved if all of those potential
members have the RESVD_ELSE bit set.

Cc: stable@vger.kernel.org
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

CONFIG_PCI is disabled by default currently.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Add some s390 specific sysfs attributes to the PCI device directory.
The following attributes are introduced:
- function_id (PCI function ID)
- function_handle (PCI function handle)
- pchid (PCI channel ID)
- pfgid (PCI function group ID aka PCI root complex)
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Add SCLP PCI configure/deconfigure and implement a PCI hotplug
controller (s390_pci_hpc). The hotplug controller creates a slot
for every PCI function in stand-by or configured state. The PCI
functions are named after the PCI function ID (fid). By writing to
the power attribute in /sys/bus/pci/slots/<fid>/power the PCI function
is moved to stand-by or configured state. If moved to the configured
state the device is automatically scanned by the s390 PCI layer.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Add CHSC store-event-information support for PCI (notfication type 2)
and report error and availability events to the PCI architecture layer.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Add DMA IOMMU support using 4K page table entries. Implement dma_map_ops.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Support PCI adapter interrupts using the Single-IRQ-mode. Single-IRQ-mode
disables an adapter IRQ automatically after delivering it until the SIC
instruction enables it again. This is used to reduce the number of IRQs
for streaming workloads.

Up to 64 MSI handlers can be registered per PCI function.
A hash table is used to map interrupt numbers to MSI descriptors.
The interrupt vector is scanned using the flogr instruction.
Only MSI/MSI-X interrupts are supported, no legacy INTs.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The flogr instruction scans a bitmap starting from the leftmost bit.
Implement support for these bitops. This could be useful to scan
bitmaps like an interrupt vector set by the hardware starting
at the leftmost bit.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

CLP instructions are used to query the firmware about detected PCI
functions, the attributes of those functions and to enable or disable
a PCI function. The CLP interface is the equivalent to a PCI bus scan.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Add PCI support for s390, (only 64 bit mode is supported by hardware):
- PCI facility tests
- PCI instructions: pcilg, pcistg, pcistb, stpcifc, mpcifc, rpcit
- map readb/w/l/q and writeb/w/l/q to pcilg and pcistg instructions
- pci_iomap implementation
- memcpy_fromio/toio
- pci_root_ops using special pcilg/pcistg
- device, bus and domain allocation
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The regular behavior of the DASD device driver when setting a device
offline is to return all outstanding I/O as failed. This behavior is
different from that of other System z operating systems and may lead
to unexpected data loss. Adding an explicit 'safe' offline function
will allow customers to use DASDs in the way they expect them to work.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

If a channel path is cabled incorrectly and the device is suspended and
resumed the device may be inaccessible afterwards.
Make the path connection check not interrupt the resume callback there
could be other valid paths available.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Reference-ID: RQM 1262
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Allow drivers to enable/disable ccwgroup devices.
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Return -EINVAL if set_{on,off}line is called for already {on,off}line
devices. Also return -EINVAL for drivers which do not provide a callback
for set_{on,off}line. This behaviour is now consistent with the one for
ccw devices.
Reported-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

I was chasing down a bug of random validity intercepts on s390.
(guest prefix page not mapped in the host virtual aspace). Turns out
that the problem was a wrong address space control element. The
cause was quite complex:

During paging activity a DAT protection during SIE caused a program
interrupt. Normally, the sie retry loop tries to catch all
interrupts during and shortly before sie to rerun the setup. The
problem is now that protection causes a suppressing program interrupt,
causing the PSW to point to the instruction AFTER SIE in case of DAT
protection. This confused the logic of the retry loop to not trigger,
instead we jumped directly back to SIE after return from
the program  interrupt. (the protection fault handler itself did
a rewind of the psw). This usually works quite well, but:

If now the protection fault handler has to wait, another program
might be scheduled in. Later on the sie process will be schedules
in again. In that case the content of CR1 (primary address space)
will be wrong because switch_to will put the user space ASCE into CR1
and not the guest ASCE.

In addition the program parameter is also wrong for every protection
fault of a guest, since we dont issue the SPP instruction.

So lets also check for PSW == instruction after SIE in the program
check handler. Instead of expensively checking all program
interruption codes that might be suppressing we assume that a program
interrupt pointing after SIE was always a program interrupt in SIE.
(Otherwise we have a kernel bug anyway).

We also have to compensate the rewinding, since the C-level handlers
will do that. Therefore we need to add a nop with the same length
as SIE before the sie_loop.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: stable@vger.kernel.org
CC: Heiko Carstens <heiko.carstens@de.ibm.com>

The current single step code is racy in regard to concurrent delivery
of signals. If a signal is delivered after a PER program check occurred
but before the TIF_PER_TRAP bit has been checked in entry[64].S the code
clears TIF_PER_TRAP and then calls do_signal. This is wrong, if the
instruction completed (or has been suppressed) a SIGTRAP should be
delivered to the debugger in any case. Only if the instruction has been
nullified the SIGTRAP may not be send.

The new logic always sets TIF_PER_TRAP if the program check indicates PER
tracing but removes it again for all program checks that are nullifying.
The effect is that for each change in the PSW address we now get a
single SIGTRAP.
Reported-by: Andreas Arnez <arnez@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>

Allow to generate code that only runs on zEC12 machines.

Also add a check which prevents the kernel to run on machines which
do not have any of the following new facilities installed:

- (48) decimal-floating-point zoned-conversion
- (49) execution-hint
- (49) load-and-trap
- (49) miscellaneous-instruction-extensions
- (49) processor-assist
- (50) constrained transactional-execution
- (73) transactional-execution

48, 49, 50 and 73 are the bit numbers of the facility indications for
each of the required facilities.

Note that we assume that user-space gets compiled with the same
compiler options, therefore we also test for a dfp facility even
if the kernel doesn't make use of it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>

Mainly merge all different per-cpu arrays into a single array which
holds all topology information per logical cpu.
Also fix the broken core vs socket variable naming and simplify the
locking a bit.
When running in environments without topology information also
invent book, socket and core ids, so that not all ids are zero.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Keep related functions together and move to appropriate file.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Move and rename init_storage_keys() to pageattr.c, so it can also be
used from the sclp memory hotplug code in order to initialize
storage keys.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The message request handling (type50 - clear key) for RSA operations
(in CRT format) are now handled correctly with respect to the crb
format container.
Signed-off-by: Ingo Tuchscherer <ingo.tuchscherer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Just convert fault_init() to an early initcall. That's still early
enough since it only needs be called before user space processes get
executed. No reason to externalize it.
Also add the function to the init section and move the store_indication
variable to the read_mostly section.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Let the dasd driver and qdio use ccw_device_get_schid and
get rid of other similar functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

This will be needed by the new virtio-ccw transport.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Remove the BUG_ON's that check for failure or incomplete
results of the s390 hardware crypto instructions.
Rather report the errors as -EIO to the crypto layer.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Remove or replace BUG/BUG_ON where possible and convert WARN_ON
to WARN_ON_ONCE if they can occur freqeuently as pointed out by:
https://lkml.org/lkml/2012/9/27/461

Checks have been removed if:
- the error condition leads to a hardware error which gets logged
  and in most cases stops the device
- the error condition is a null pointer access
- the error condition is just pointless or already handled at
  another location
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Do not use more than one KERN_<level> per printk.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Preinitialize the program check table, so we can put it into the
read-only data section.
Also use only four byte entries for the table, since each program
check handler resides within the first 2GB. Therefore this reduces
the size of the table by 50% on 64 bit builds.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Use 1MB frames for vmemmap if EDAT1 is available in order to
reduce TLB pressure
Always use a 1MB frame even if its only partially needed for
struct pages. Otherwise we would end up with a mix of large
frame and page mappings, because vmemmap_populate gets called
for each section (256MB -> 3.5MB memmap) separately.
Worst case is that we would waste 512KB.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Use 2GB frames for indentity mapping if EDAT2 is
available to reduce TLB pressure.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Pull input updates from Dmitry Torokhov:
 "This fixes recent regression where /dev/input/mice got assigned wrong
  device node which messed up setups with static /dev, and a regression
  in ads7846 GPIO debounce setup."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  ARM - OMAP: ads7846: fix pendown debounce setting
  Input: ads7846 - enable pendown GPIO debounce time setting
  Input: mousedev - move /dev/input/mice to the correct minor
  Input: MT - document new 'flags' argument of input_mt_init_slots()

Pull ARM SoC fixes from Olof Johansson:
 "A few more fixes for final 3.7.  Two dealing with pinmux setup on
  OMAP, and one dealing with TV output on DaVinci.  And one small
  MAINTAINER update."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: davinci: dm644x: fix out range signal for ED
  ARM: OMAP4: TWL: mux sys_drm_msecure as output for PMIC
  ARM: OMAP3: igep0020: Set WIFI/BT GPIO pins in correct mux mode
  ARM: OMAP: Add maintainer entry for IGEP machines

Pull PARISC fixes from James Bottomley:
 "This is two bug fixes: one fixes a loophole where rt_sigprocmask()
  with the wrong values panics the box (Denial of Service) and the other
  fixes an aliasing problem with get_shared_area() which could cause
  data corruption.

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
  [PARISC] fix user-triggerable panic on parisc
  [PARISC] fix virtual aliasing issue in get_shared_area()