- 21 Jan, 2022 16 commits
-
-
Geetha sowjanya authored
While freeing SQB pointers to aura, driver first memcpy to target address and then triggers lmtst operation to free pointer to the aura. We need to ensure(by adding dmb barrier)that memcpy is finished before pointers are freed to the aura. This patch also adds the missing sq context structure entry in debugfs. Fixes: ef6c8da7 ("octeontx2-pf: cn10K: Reserve LMTST lines per core") Signed-off-by:
Geetha sowjanya <gakula@marvell.com> Signed-off-by:
Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by:
Sunil Goutham <sgoutham@marvell.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Geetha sowjanya authored
CN10K platforms uses RPM(0..2)_MTI_MAC100(0..3)_COMMAND_CONFIG register for lmac TX/RX enable whereas CN9xxx platforms use CGX_CMRX_CONFIG register. This config change was missed when adding support for CN10K RPM. Fixes: 91c6945e ("octeontx2-af: cn10k: Add RPM MAC support") Signed-off-by:
-
Geetha sowjanya authored
Few RVU blocks like SSO require more time for reset on some silicons. Hence retrying the block reset until success. Fixes: c0fa2cff ("octeontx2-af: Handle return value in block reset") Signed-off-by:
-
Sunil Goutham authored
In rvu_nix_get_bpid() lbk_bpid_cnt is being read from wrong register. Due to this backpressure enable is failing for LBK VF32 onwards. This patch fixes that. Fixes: fe1939bb ("octeontx2-af: Add SDP interface support") Signed-off-by:
-
Subbaraya Sundeep authored
AF modifies all the rules destined for VF to use the action same as default RSS action. This fixup was needed because AF only installs default rules with RSS action. But the action in rules installed by a PF for its VFs should not be changed by this fixup. This is because action can be drop or direct to queue as specified by user(ntuple filters). This patch fixes that problem. Fixes: 967db352 ("octeontx2-af: add support for multicast/promisc packet") Signed-off-by:
Naveen Mamindlapalli <naveenm@marvell.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wirelessDavid S. Miller authored
Kalle Valo says: ==================== wireless fixes for v5.17 First set of fixes for v5.17. This is the first pull request from the new wireless tree and only changes to MAINTAINERS file. ==================== Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queueDavid S. Miller authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2022-01-20 This series contains updates to i40e driver only. Jedrzej increases delay for EMP reset and adds checks to ensure a VF request to change queues can be met. Sylwester moves the placement of the Flow Director queue as to not fragment the queue pile which would cause later re-allocation issues. Karen prevents VF reset being invoked while another is still occurring to avoid reading invalid data. Joe Damato fixes some statistics fields to match the values of the fields they are based on. ==================== Signed-off-by: -
Jakub Kicinski authored
Mat Martineau says: ==================== mptcp: A few fixes Patch 1 fixes a RCU locking issue when processing a netlink command that updates endpoint flags in the in-kernel MPTCP path manager. Patch 2 fixes a typo affecting available endpoint id tracking. Patch 3 fixes IPv6 routing in the MPTCP self tests. ==================== Link: https://lore.kernel.org/r/20220121003529.54930-1-mathew.j.martineau@linux.intel.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Paolo Abeni authored
MPJ ipv6 selftests currently lack per link route to the server net. Additionally, ipv6 subflows endpoints are created without any interface specified. The end-result is that in ipv6 self-tests subflows are created all on the same link, leading to expected delays and sporadic self-tests failures. Fix the issue by adding the missing setup bits. Fixes: 523514ed ("selftests: mptcp: add ADD_ADDR IPv6 test cases") Reported-and-tested-by:
Geliang Tang <geliang.tang@suse.com> Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by:
-
Geliang Tang authored
In mptcp_pm_nl_rm_addr_or_subflow(), the bit of rm_list->ids[i] in the id_avail_bitmap should be set, not rm_list->ids[1]. This patch fixed it. Fixes: 86e39e04 ("mptcp: keep track of local endpoint still available for each msk") Acked-by:
-
Paolo Abeni authored
The MPTCP endpoint list is under RCU protection, guarded by the pernet spinlock. mptcp_nl_cmd_set_flags() traverses the list without acquiring the spin-lock nor under the RCU critical section. This change addresses the issue performing the lookup and the endpoint update under the pernet spinlock. Fixes: 0f9f696a ("mptcp: add set_flags command in PM netlink") Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfJakub Kicinski authored
Pablo Neira Ayuso says: ==================== Netfilter fixes for net 1) Incorrect helper module alias in netbios_ns, from Florian Westphal. 2) Remove unused variable in nf_tables. 3) Uninitialized last expression in nf_tables register tracking. 4) Memleak in nft_connlimit after moving stateful data out of the expression data area. 5) Bogus invalid stats update when NF_REPEAT is returned, from Florian. * git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf: netfilter: conntrack: don't increment invalid counter on NF_REPEAT netfilter: nft_connlimit: memleak if nf_ct_netns_get() fails netfilter: nf_tables: set last expression in register tracking area netfilter: nf_tables: remove unused variable netfilter: nf_conntrack_netbios_ns: fix helper module alias ==================== Link: https://lore.kernel.org/r/20220120125212.991271-1-pablo@netfilter.orgSigned-off-by:
-
Eric Dumazet authored
struct fib6_node's fn_sernum field can be read while other threads change it. Add READ_ONCE()/WRITE_ONCE() annotations. Do not change existing smp barriers in fib6_get_cookie_safe() and __fib6_update_sernum_upto_root() syzbot reported: BUG: KCSAN: data-race in fib6_clean_node / inet6_csk_route_socket write to 0xffff88813df62e2c of 4 bytes by task 1920 on cpu 1: fib6_clean_node+0xc2/0x260 net/ipv6/ip6_fib.c:2178 fib6_walk_continue+0x38e/0x430 net/ipv6/ip6_fib.c:2112 fib6_walk net/ipv6/ip6_fib.c:2160 [inline] fib6_clean_tree net/ipv6/ip6_fib.c:2240 [inline] __fib6_clean_all+0x1a9/0x2e0 net/ipv6/ip6_fib.c:2256 fib6_flush_trees+0x6c/0x80 net/ipv6/ip6_fib.c:2281 rt_genid_bump_ipv6 include/net/net_namespace.h:488 [inline] addrconf_dad_completed+0x57f/0x870 net/ipv6/addrconf.c:4230 addrconf_dad_work+0x908/0x1170 process_one_work+0x3f6/0x960 kernel/workqueue.c:2307 worker_thread+0x616/0xa70 kernel/workqueue.c:2454 kthread+0x1bf/0x1e0 kernel/kthread.c:359 ret_from_fork+0x1f/0x30 read to 0xffff88813df62e2c of 4 bytes by task 15701 on cpu 0: fib6_get_cookie_safe include/net/ip6_fib.h:285 [inline] rt6_get_cookie include/net/ip6_fib.h:306 [inline] ip6_dst_store include/net/ip6_route.h:234 [inline] inet6_csk_route_socket+0x352/0x3c0 net/ipv6/inet6_connection_sock.c:109 inet6_csk_xmit+0x91/0x1e0 net/ipv6/inet6_connection_sock.c:121 __tcp_transmit_skb+0x1323/0x1840 net/ipv4/tcp_output.c:1402 tcp_transmit_skb net/ipv4/tcp_output.c:1420 [inline] tcp_write_xmit+0x1450/0x4460 net/ipv4/tcp_output.c:2680 __tcp_push_pending_frames+0x68/0x1c0 net/ipv4/tcp_output.c:2864 tcp_push+0x2d9/0x2f0 net/ipv4/tcp.c:725 mptcp_push_release net/mptcp/protocol.c:1491 [inline] __mptcp_push_pending+0x46c/0x490 net/mptcp/protocol.c:1578 mptcp_sendmsg+0x9ec/0xa50 net/mptcp/protocol.c:1764 inet6_sendmsg+0x5f/0x80 net/ipv6/af_inet6.c:643 sock_sendmsg_nosec net/socket.c:705 [inline] sock_sendmsg net/socket.c:725 [inline] kernel_sendmsg+0x97/0xd0 net/socket.c:745 sock_no_sendpage+0x84/0xb0 net/core/sock.c:3086 inet_sendpage+0x9d/0xc0 net/ipv4/af_inet.c:834 kernel_sendpage+0x187/0x200 net/socket.c:3492 sock_sendpage+0x5a/0x70 net/socket.c:1007 pipe_to_sendpage+0x128/0x160 fs/splice.c:364 splice_from_pipe_feed fs/splice.c:418 [inline] __splice_from_pipe+0x207/0x500 fs/splice.c:562 splice_from_pipe fs/splice.c:597 [inline] generic_splice_sendpage+0x94/0xd0 fs/splice.c:746 do_splice_from fs/splice.c:767 [inline] direct_splice_actor+0x80/0xa0 fs/splice.c:936 splice_direct_to_actor+0x345/0x650 fs/splice.c:891 do_splice_direct+0x106/0x190 fs/splice.c:979 do_sendfile+0x675/0xc40 fs/read_write.c:1245 __do_sys_sendfile64 fs/read_write.c:1310 [inline] __se_sys_sendfile64 fs/read_write.c:1296 [inline] __x64_sys_sendfile64+0x102/0x140 fs/read_write.c:1296 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae value changed: 0x0000026f -> 0x00000271 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 15701 Comm: syz-executor.2 Not tainted 5.16.0-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 The Fixes tag I chose is probably arbitrary, I do not think we need to backport this patch to older kernels. Fixes: c5cff856 ("ipv6: add rcu grace period before freeing fib6_node") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Link: https://lore.kernel.org/r/20220120174112.1126644-1-eric.dumazet@gmail.comSigned-off-by:
-
Eric Dumazet authored
Without it, splice users can hit the warning added in commit 79074a72 ("net: Flush deferred skb free on socket destroy") Fixes: f35f8219 ("tcp: defer skb freeing after socket lock is released") Fixes: 79074a72 ("net: Flush deferred skb free on socket destroy") Suggested-by:
-
Gal Pressman authored
When compiling the kernel with CONFIG_INET disabled, the sk_defer_free_flush() should be defined as a nop. This resolves the following compilation error: ld: net/core/sock.o: in function `sk_defer_free_flush': ./include/net/tcp.h:1378: undefined reference to `__sk_defer_free_flush' Fixes: 79074a72 ("net: Flush deferred skb free on socket destroy") Reported-by:
kernel test robot <lkp@intel.com> Reviewed-by:
Tariq Toukan <tariqt@nvidia.com> Signed-off-by:
Gal Pressman <gal@nvidia.com> Reviewed-by:
-
Marek Behún authored
Commit bafbdd52 ("phylib: Add device reset GPIO support") added call to phy_device_reset(phydev) after the put_device() call in phy_detach(). The comment before the put_device() call says that the phydev might go away with put_device(). Fix potential use-after-free by calling phy_device_reset() before put_device(). Fixes: bafbdd52 ("phylib: Add device reset GPIO support") Signed-off-by:
Marek Behún <kabel@kernel.org> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220119162748.32418-1-kabel@kernel.orgSigned-off-by:
-
- 20 Jan, 2022 24 commits
-
-
Joe Damato authored
Change i40e_update_vsi_stats and struct i40e_vsi to use u64 fields to match the width of the stats counters in struct i40e_rx_queue_stats. Update debugfs code to use the correct format specifier for u64. Fixes: 41c445ff ("i40e: main driver core") Signed-off-by:
Joe Damato <jdamato@fastly.com> Reported-by:
Gurucharan G <gurucharanx.g@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Karen Sornek authored
Fix for failed to init adminq: -53 while VF is resetting via MAC address changing procedure. Added sync module to avoid reading deadbeef value in reinit adminq during software reset. Without this patch it is possible to trigger VF reset procedure during reinit adminq. This resulted in an incorrect reading of value from the AQP registers and generated the -53 error. Fixes: 5c3c48ac ("i40e: implement virtual device interface") Signed-off-by:
Grzegorz Szczurek <grzegorzx.szczurek@intel.com> Signed-off-by:
Karen Sornek <karen.sornek@intel.com> Tested-by:
Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by:
-
Sylwester Dziedziuch authored
When XDP was configured on a system with large number of CPUs and X722 NIC there was a call trace with NULL pointer dereference. i40e 0000:87:00.0: failed to get tracking for 256 queues for VSI 0 err -12 i40e 0000:87:00.0: setup of MAIN VSI failed BUG: kernel NULL pointer dereference, address: 0000000000000000 RIP: 0010:i40e_xdp+0xea/0x1b0 [i40e] Call Trace: ? i40e_reconfig_rss_queues+0x130/0x130 [i40e] dev_xdp_install+0x61/0xe0 dev_xdp_attach+0x18a/0x4c0 dev_change_xdp_fd+0x1e6/0x220 do_setlink+0x616/0x1030 ? ahci_port_stop+0x80/0x80 ? ata_qc_issue+0x107/0x1e0 ? lock_timer_base+0x61/0x80 ? __mod_timer+0x202/0x380 rtnl_setlink+0xe5/0x170 ? bpf_lsm_binder_transaction+0x10/0x10 ? security_capable+0x36/0x50 rtnetlink_rcv_msg+0x121/0x350 ? rtnl_calcit.isra.0+0x100/0x100 netlink_rcv_skb+0x50/0xf0 netlink_unicast+0x1d3/0x2a0 netlink_sendmsg+0x22a/0x440 sock_sendmsg+0x5e/0x60 __sys_sendto+0xf0/0x160 ? __sys_getsockname+0x7e/0xc0 ? _copy_from_user+0x3c/0x80 ? __sys_setsockopt+0xc8/0x1a0 __x64_sys_sendto+0x20/0x30 do_syscall_64+0x33/0x40 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f83fa7a39e0 This was caused by PF queue pile fragmentation due to flow director VSI queue being placed right after main VSI. Because of this main VSI was not able to resize its queue allocation for XDP resulting in no queues allocated for main VSI when XDP was turned on. Fix this by always allocating last queue in PF queue pile for a flow director VSI. Fixes: 41c445ff ("i40e: main driver core") Fixes: 74608d17 ("i40e: add support for XDP_TX action") Signed-off-by:
Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by:
Mateusz Palczewski <mateusz.palczewski@intel.com> Reviewed-by:
Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by:
Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by:
-
Jedrzej Jagielski authored
Before this patch VF interface vanished when maximum queue number was exceeded. Driver tried to add next queues even if there was not enough space. PF sent incorrect number of queues to the VF when there were not enough of them. Add an additional condition introduced to check available space in 'qp_pile' before proceeding. This condition makes it impossible to add queues if they number is greater than the number resulting from available space. Also add the search for free space in PF queue pair piles. Without this patch VF interfaces are not seen when available space for queues has been exceeded and following logs appears permanently in dmesg: "Unable to get VF config (-32)". "VF 62 failed opcode 3, retval: -5" "Unable to get VF config due to PF error condition, not retrying" Fixes: 7daa6bf3 ("i40e: driver core headers") Fixes: 41c445ff ("i40e: main driver core") Signed-off-by:
Jaroslaw Gawin <jaroslawx.gawin@intel.com> Signed-off-by:
Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by:
Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by:
-
Jedrzej Jagielski authored
Recently simplified i40e_rebuild causes that FW sometimes is not ready after NVM update, the ping does not return. Increase the delay in case of EMP reset. Old delay of 300 ms was introduced for specific cards for 710 series. Now it works for all the cards and delay was increased. Fixes: 1fa51a65 ("i40e: Add delay after EMP reset for firmware to recover") Signed-off-by:
Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by:
-
David S. Miller authored
Yuji Ishikawa says: ==================== net: stmmac: dwmac-visconti: Fix bit definitions and clock configuration for RMII mode This series is a fix for RMII/MII operation mode of the dwmac-visconti driver. It is composed of two parts: * 1/2: fix constant definitions for cleared bits in ETHER_CLK_SEL register * 2/2: fix configuration of ETHER_CLK_SEL register for running in RMII operation mode. net: stmmac: dwmac-visconti: Fix bit definitions for ETHER_CLK_SEL v1 -> v2: - added Fixes tag to commit message net: stmmac: dwmac-visconti: Fix clock configuration for RMII mode v1 -> v2: - added Fixes tag to commit message ==================== Signed-off-by: -
Yuji Ishikawa authored
Bit pattern of the ETHER_CLOCK_SEL register for RMII/MII mode should be fixed. Also, some control bits should be modified with a specific sequence. Fixes: b38dd98f ("net: stmmac: Add Toshiba Visconti SoCs glue driver") Signed-off-by:
Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp> Reviewed-by:
Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by:
-
Yuji Ishikawa authored
just 0 should be used to represent cleared bits * ETHER_CLK_SEL_DIV_SEL_20 * ETHER_CLK_SEL_TX_CLK_EXT_SEL_IN * ETHER_CLK_SEL_RX_CLK_EXT_SEL_IN * ETHER_CLK_SEL_TX_CLK_O_TX_I * ETHER_CLK_SEL_RMII_CLK_SEL_IN Fixes: b38dd98f ("net: stmmac: Add Toshiba Visconti SoCs glue driver") Signed-off-by:
-
Ido Schimmel authored
The warning messages can be invoked from the data path for every packet transmitted through an ip6gre netdev, leading to high CPU utilization. Fix that by rate limiting the messages. Fixes: 09c6bbf0 ("[IPV6]: Do mandatory IPv6 tunnel endpoint checks in realtime") Reported-by:
Maksym Yaremchuk <maksymy@nvidia.com> Tested-by:
Ido Schimmel <idosch@nvidia.com> Reviewed-by:
Amit Cohen <amcohen@nvidia.com> Signed-off-by:
-
Moshe Tal authored
The link extended sub-states are assigned as enum that is an integer size but read from a union as u8, this is working for small values on little endian systems but for big endian this always give 0. Fix the variable in the union to match the enum size. Fixes: ecc31c60 ("ethtool: Add link extended state") Signed-off-by:
Moshe Tal <moshet@nvidia.com> Reviewed-by:
-
Robert Hancock authored
A problem was encountered with the Bel-Fuse 1GBT-SFP05 SFP module (which is a 1 Gbps copper module operating in SGMII mode with an internal BCM54616S PHY device) using the Xilinx AXI Ethernet MAC core, where the module would work properly on the initial insertion or boot of the device, but after the device was rebooted, the link would either only come up at 100 Mbps speeds or go up and down erratically. I found no meaningful changes in the PHY configuration registers between the working and non-working boots, but the status registers seemed to have a lot of error indications set on the SERDES side of the device on the non-working boot. I suspect the problem is that whatever happens on the SGMII link when the device is rebooted and the FPGA logic gets reloaded ends up putting the module's onboard PHY into a bad state. Since commit 6e2d85ec ("net: phy: Stop with excessive soft reset") the genphy_soft_reset call is not made automatically by the PHY core unless the callback is explicitly specified in the driver structure. For most of these Broadcom devices, there is probably a hardware reset that gets asserted to reset the PHY during boot, however for SFP modules (where the BCM54616S is commonly found) no such reset line exists, so if the board keeps the SFP cage powered up across a reboot, it will end up with no reset occurring during reboots. Hook up the genphy_soft_reset callback for BCM54616S to ensure that a PHY reset is performed before the device is initialized. This appears to fix the issue with erratic operation after a reboot with this SFP module. Fixes: 6e2d85ec ("net: phy: Stop with excessive soft reset") Signed-off-by:
Robert Hancock <robert.hancock@calian.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Victor Nogueira authored
When adding a tc rule with a qdisc kind that is not supported or not compiled into the kernel, the kernel emits the following error: "Error: Specified qdisc not found.". Found via tdc testing when ETS qdisc was not compiled in and it was not obvious right away what the message meant without looking at the kernel code. Change the error message to be more explicit and say the qdisc kind is unknown. Signed-off-by:
Victor Nogueira <victor@mojatatu.com> Signed-off-by:
-
Congyu Liu authored
In one net namespace, after creating a packet socket without binding it to a device, users in other net namespaces can observe the new `packet_type` added by this packet socket by reading `/proc/net/ptype` file. This is minor information leakage as packet socket is namespace aware. Add a net pointer in `packet_type` to keep the net namespace of of corresponding packet socket. In `ptype_seq_show`, this net pointer must be checked when it is not NULL. Fixes: 2feb27db ("[NETNS]: Minor information leak via /proc/net/ptype file.") Signed-off-by:
Congyu Liu <liu3101@purdue.edu> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Jakub Kicinski: "Including fixes from netfilter, bpf. Quite a handful of old regression fixes but most of those are pre-5.16. Current release - regressions: - fix memory leaks in the skb free deferral scheme if upper layer protocols are used, i.e. in-kernel TCP readers like TLS Current release - new code bugs: - nf_tables: fix NULL check typo in _clone() functions - change the default to y for Vertexcom vendor Kconfig - a couple of fixes to incorrect uses of ref tracking - two fixes for constifying netdev->dev_addr Previous releases - regressions: - bpf: - various verifier fixes mainly around register offset handling when passed to helper functions - fix mount source displayed for bpffs (none -> bpffs) - bonding: - fix extraction of ports for connection hash calculation - fix bond_xmit_broadcast return value when some devices are down - phy: marvell: add Marvell specific PHY loopback - sch_api: don't skip qdisc attach on ingress, prevent ref leak - htb: restore minimal packet size handling in rate control - sfp: fix high power modules without diagnostic monitoring - mscc: ocelot: - don't let phylink re-enable TX PAUSE on the NPI port - don't dereference NULL pointers with shared tc filters - smsc95xx: correct reset handling for LAN9514 - cpsw: avoid alignment faults by taking NET_IP_ALIGN into account - phy: micrel: use kszphy_suspend/_resume for irq aware devices, avoid races with the interrupt Previous releases - always broken: - xdp: check prog type before updating BPF link - smc: resolve various races around abnormal connection termination - sit: allow encapsulated IPv6 traffic to be delivered locally - axienet: fix init/reset handling, add missing barriers, read the right status words, stop queues correctly - add missing dev_put() in sock_timestamping_bind_phc() Misc: - ipv4: prevent accidentally passing RTO_ONLINK to ip_route_output_key_hash() by sanitizing flags - ipv4: avoid quadratic behavior in netns dismantle - stmmac: dwmac-oxnas: add support for OX810SE - fsl: xgmac_mdio: add workaround for erratum A-009885" * tag 'net-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (92 commits) ipv4: add net_hash_mix() dispersion to fib_info_laddrhash keys ipv4: avoid quadratic behavior in netns dismantle net/fsl: xgmac_mdio: Fix incorrect iounmap when removing module powerpc/fsl/dts: Enable WA for erratum A-009885 on fman3l MDIO buses dt-bindings: net: Document fsl,erratum-a009885 net/fsl: xgmac_mdio: Add workaround for erratum A-009885 net: mscc: ocelot: fix using match before it is set net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices net: cpsw: avoid alignment faults by taking NET_IP_ALIGN into account nfc: llcp: fix NULL error pointer dereference on sendmsg() after failed bind() net: axienet: increase default TX ring size to 128 net: axienet: fix for TX busy handling net: axienet: fix number of TX ring slots for available check net: axienet: Fix TX ring slot available check net: axienet: limit minimum TX ring size net: axienet: add missing memory barriers net: axienet: reset core on initialization prior to MDIO access net: axienet: Wait for PhyRstCmplt after core reset net: axienet: increase reset timeout bpf, selftests: Add ringbuf memory type confusion test ... -
Linus Torvalds authored
Merge more updates from Andrew Morton: "55 patches. Subsystems affected by this patch series: percpu, procfs, sysctl, misc, core-kernel, get_maintainer, lib, checkpatch, binfmt, nilfs2, hfs, fat, adfs, panic, delayacct, kconfig, kcov, and ubsan" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (55 commits) lib: remove redundant assignment to variable ret ubsan: remove CONFIG_UBSAN_OBJECT_SIZE kcov: fix generic Kconfig dependencies if ARCH_WANTS_NO_INSTR lib/Kconfig.debug: make TEST_KMOD depend on PAGE_SIZE_LESS_THAN_256KB btrfs: use generic Kconfig option for 256kB page size limit arch/Kconfig: split PAGE_SIZE_LESS_THAN_256KB from PAGE_SIZE_LESS_THAN_64KB configs: introduce debug.config for CI-like setup delayacct: track delays from memory compact Documentation/accounting/delay-accounting.rst: add thrashing page cache and direct compact delayacct: cleanup flags in struct task_delay_info and functions use it delayacct: fix incomplete disable operation when switch enable to disable delayacct: support swapin delay accounting for swapping without blkio panic: remove oops_id panic: use error_report_end tracepoint on warnings fs/adfs: remove unneeded variable make code cleaner FAT: use io_schedule_timeout() instead of congestion_wait() hfsplus: use struct_group_attr() for memcpy() region nilfs2: remove redundant pointer sbufs fs/binfmt_elf: use PT_LOAD p_align values for static PIE const_structs.checkpatch: add frequently used ops structs ...
-
Colin Ian King authored
The variable ret is being assigned a value that is never read. If the for-loop is entered then ret is immediately re-assigned a new value. If the for-loop is not executed ret is never read. The assignment is redundant and can be removed. Link: https://lkml.kernel.org/r/20211230134557.83633-1-colin.i.king@gmail.comSigned-off-by:
Colin Ian King <colin.i.king@gmail.com> Reviewed-by:
Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Kees Cook authored
The object-size sanitizer is redundant to -Warray-bounds, and inappropriately performs its checks at run-time when all information needed for the evaluation is available at compile-time, making it quite difficult to use: https://bugzilla.kernel.org/show_bug.cgi?id=214861 With -Warray-bounds almost enabled globally, it doesn't make sense to keep this around. Link: https://lkml.kernel.org/r/20211203235346.110809-1-keescook@chromium.orgSigned-off-by:
Kees Cook <keescook@chromium.org> Reviewed-by:
Marco Elver <elver@google.com> Cc: Masahiro Yamada <masahiroy@kernel.org> Cc: Michal Marek <michal.lkml@markovi.net> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Marco Elver authored
Until recent versions of GCC and Clang, it was not possible to disable KCOV instrumentation via a function attribute. The relevant function attribute was introduced in 540540d0 ("kcov: add __no_sanitize_coverage to fix noinstr for all architectures"). x86 was the first architecture to want a working noinstr, and at the time no compiler support for the attribute existed yet. Therefore, commit 0f1441b4 ("objtool: Fix noinstr vs KCOV") introduced the ability to NOP __sanitizer_cov_*() calls in .noinstr.text. However, this doesn't work for other architectures like arm64 and s390 that want a working noinstr per ARCH_WANTS_NO_INSTR. At the time of 0f1441b4, we didn't yet have ARCH_WANTS_NO_INSTR, but now we can move the Kconfig dependency checks to the generic KCOV option. KCOV will be available if: - architecture does not care about noinstr, OR - we have objtool support (like on x86), OR - GCC is 12.0 or newer, OR - Clang is 13.0 or newer. Link: https://lkml.kernel.org/r/20211201152604.3984495-1-elver@google.comSigned-off-by:
Nathan Chancellor <nathan@kernel.org> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Signed-off-by:
-
Nathan Chancellor authored
Commit b05fbcc3 ("btrfs: disable build on platforms having page size 256K") disabled btrfs for configurations that used a 256kB page size. However, it did not fully solve the problem because CONFIG_TEST_KMOD selects CONFIG_BTRFS, which does not account for the dependency. This results in a Kconfig warning and the failed BUILD_BUG_ON error returning. WARNING: unmet direct dependencies detected for BTRFS_FS Depends on [n]: BLOCK [=y] && !PPC_256K_PAGES && !PAGE_SIZE_256KB [=y] Selected by [m]: - TEST_KMOD [=m] && RUNTIME_TESTING_MENU [=y] && m && MODULES [=y] && NETDEVICES [=y] && NET_CORE [=y] && INET [=y] && BLOCK [=y] To resolve this, add CONFIG_PAGE_SIZE_LESS_THAN_256KB as a dependency of CONFIG_TEST_KMOD so there is no more invalid configuration or build errors. Link: https://lkml.kernel.org/r/20211129230141.228085-4-nathan@kernel.org Fixes: b05fbcc3 ("btrfs: disable build on platforms having page size 256K") Signed-off-by:
-
Nathan Chancellor authored
Use the newly introduced CONFIG_PAGE_SIZE_LESS_THAN_256KB to describe the dependency introduced by commit b05fbcc3 ("btrfs: disable build on platforms having page size 256K"). Link: https://lkml.kernel.org/r/20211129230141.228085-3-nathan@kernel.orgSigned-off-by:
David Sterba <dsterba@suse.com> Cc: Chris Mason <clm@fb.com> Cc: Josef Bacik <josef@toxicpanda.com> Cc: kernel test robot <lkp@intel.com> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
-
Nathan Chancellor authored
Patch series "Fix CONFIG_TEST_KMOD with 256kB page size". The kernel test robot reported a build error [1] from a failed assertion in fs/btrfs/inode.c with a hexagon randconfig that includes CONFIG_PAGE_SIZE_256KB. This error is the same one that was addressed by commit b05fbcc3 ("btrfs: disable build on platforms having page size 256K") but CONFIG_TEST_KMOD selects CONFIG_BTRFS without having the "page size less than 256kB dependency", which results in the error reappearing. The first patch introduces CONFIG_PAGE_SIZE_LESS_THAN_256KB by splitting it off from CONFIG_PAGE_SIZE_LESS_THAN_64KB, which was introduced in commit 1f0e290c ("arch: Add generic Kconfig option indicating page size smaller than 64k") for a similar reason in 5.16-rc3. The second patch uses that configuration option for CONFIG_BTRFS to reduce duplication. The third patch resolves the build error by adding CONFIG_PAGE_SIZE_LESS_THAN_256KB as a dependency to CONFIG_TEST_KMOD so that CONFIG_BTRFS does not get enabled under that invalid configuration. [1]: https://lore.kernel.org/r/202111270255.UYOoN5VN-lkp@intel.com/ This patch (of 3): btrfs requires a page size smaller than 256kB. To use that dependency in other places, introduce CONFIG_PAGE_SIZE_LESS_THAN_256KB and reuse that dependency in CONFIG_PAGE_SIZE_LESS_THAN_64KB. Link: https://lkml.kernel.org/r/20211129230141.228085-1-nathan@kernel.org Link: https://lkml.kernel.org/r/20211129230141.228085-2-nathan@kernel.orgSigned-off-by:
-
Qian Cai authored
Some general debugging features like kmemleak, KASAN, lockdep, UBSAN etc help fix many viruses like a microscope. On the other hand, those features are scatter around and mixed up with more situational debugging options making them difficult to consume properly. This cold help amplify the general debugging/testing efforts and help establish sensitive default values for those options across the broad. This could also help different distros to collaborate on maintaining debug-flavored kernels. The config is based on years' experiences running daily CI inside the largest enterprise Linux distro company to seek regressions on linux-next builds on different bare-metal and virtual platforms. It can be used for example, $ make ARCH=arm64 defconfig debug.config Since KASAN and KCSAN can't be enabled together, we will need to create a separate one for KCSAN later as well. Link: https://lkml.kernel.org/r/20211115134754.7334-1-quic_qiancai@quicinc.comSigned-off-by:
Qian Cai <quic_qiancai@quicinc.com> Acked-by:
Paul E. McKenney <paulmck@kernel.org> Cc: Marco Elver <elver@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: Masahiro Yamada <masahiroy@kernel.org> Cc: Naresh Kamboju <naresh.kamboju@linaro.org> Cc: "Stephen Rothwell" <sfr@canb.auug.org.au> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
-
wangyong authored
Delay accounting does not track the delay of memory compact. When there is not enough free memory, tasks can spend a amount of their time waiting for compact. To get the impact of tasks in direct memory compact, measure the delay when allocating memory through memory compact. Also update tools/accounting/getdelays.c: / # ./getdelays_next -di -p 304 print delayacct stats ON printing IO accounting PID 304 CPU count real total virtual total delay total delay average 277 780000000 849039485 18877296 0.068ms IO count delay total delay average 0 0 0ms SWAP count delay total delay average 0 0 0ms RECLAIM count delay total delay average 5 11088812685 2217ms THRASHING count delay total delay average 0 0 0ms COMPACT count delay total delay average 3 72758 0ms watch: read=0, write=0, cancelled_write=0 Link: https://lkml.kernel.org/r/1638619795-71451-1-git-send-email-wang.yong12@zte.com.cnSigned-off-by:wangyong <wang.yong12@zte.com.cn> Reviewed-by:
Jiang Xuexin <jiang.xuexin@zte.com.cn> Reviewed-by:
Zhang Wenya <zhang.wenya1@zte.com.cn> Reviewed-by:
Yang Yang <yang.yang29@zte.com.cn> Reviewed-by:
Balbir Singh <bsingharora@gmail.com> Signed-off-by:
-
wangyong authored
Add thrashing page cache and direct compact related descriptions and update the usage of getdelays userspace utility. The following patches modifications have been updated: https://lore.kernel.org/all/20190312102002.31737-4-jinpuwang@gmail.com/ https://lore.kernel.org/all/1638619795-71451-1-git-send-email- wang.yong12@zte.com.cn/ Link: https://lkml.kernel.org/r/1639583021-92977-1-git-send-email-wang.yong12@zte.com.cnSigned-off-by:
Zeal Robot <zealci@zte.com.cn> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
