575XX (P5) chips have the same UDP RSS hashing capability as P4 chips,
so we can enable it on P5 chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The dev_port is meant to distinguish the network ports belonging to
the same PCI function.  Our devices only have one network port
associated with each PCI function and so we should not set it for
correctness.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the 2nd parameter fw_dflt is not set, we are calling bnxt_probe_phy()
after the firmware has reset.  There is no need to query the current
PHY settings from firmware as these settings may be different from
the ethtool settings that the driver will re-establish later.  So
return earlier in bnxt_probe_phy() to save one firmware call.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In bnxt_update_phy_setting(), ethtool_get_link_ksettings() and
bnxt_disable_an_for_lpbk(), we inconsistently use netif_carrier_ok()
to determine link.  Instead, we should use bp->link_info.link_up
which has the true link state.  The netif_carrier state may be off
during self-test and while the device is being reset and may not always
reflect the true link state.

By always using bp->link_info.link_up, the code is now more
consistent and more correct.  Some unnecessary link toggles are
now prevented with this patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michal Kubecek says:

====================
ethtool netlink interface, part 2

This shorter series adds support for getting and setting of wake-on-lan
settings and message mask (originally message level). Together with the
code already in net-next, this will allow full implementation of
"ethtool <dev>" and "ethtool -s <dev> ...".

Older versions of the ethtool netlink series allowed getting WoL settings
by unprivileged users and only filtered out the password but this was
a source of controversy so for now, ETHTOOL_MSG_WOL_GET request always
requires CAP_NET_ADMIN as ETHTOOL_GWOL ioctl request does.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Send ETHTOOL_MSG_WOL_NTF notification whenever wake-on-lan settings of
a device are modified using ETHTOOL_MSG_WOL_SET netlink message or
ETHTOOL_SWOL ioctl request.

As notifications can be received by anyone, do not include SecureOn(tm)
password in notification messages.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement WOL_SET netlink request to set wake-on-lan settings. This is
equivalent to ETHTOOL_SWOL ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement WOL_GET request to get wake-on-lan settings for a device,
traditionally available via ETHTOOL_GWOL ioctl request.

As part of the implementation, provide symbolic names for wake-on-line
modes as ETH_SS_WOL_MODES string set.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Send ETHTOOL_MSG_DEBUG_NTF notification message whenever debugging message
mask for a device are modified using ETHTOOL_MSG_DEBUG_SET netlink message
or ETHTOOL_SMSGLVL ioctl request.

The notification message has the same format as reply to DEBUG_GET request.
As with other ethtool notifications, netlink requests only trigger the
notification if the mask is actually changed while ioctl request trigger it
whenever the request results in calling the ethtool_ops handler.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement DEBUG_SET netlink request to set debugging settings for a device.
At the moment, only message mask corresponding to message level as set by
ETHTOOL_SMSGLVL ioctl request can be set. (It is called message level in
ioctl interface but almost all drivers interpret it as a bit mask.)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement DEBUG_GET request to get debugging settings for a device. At the
moment, only message mask corresponding to message level as reported by
ETHTOOL_GMSGLVL ioctl request is provided. (It is called message level in
ioctl interface but almost all drivers interpret it as a bit mask.)

As part of the implementation, provide symbolic names for message mask bits
as ETH_SS_MSG_CLASSES string set.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix missing or incorrect function argument and struct member descriptions.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-2020-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for v5.6

Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.

Major changes:

ar5523

* add support for SMCWUSBT-G2 USB device

iwlwifi

* support new versions of the FTM FW APIs

* support new version of the beacon template FW API

* print some extra information when the driver is loaded

rtw88

* support wowlan feature for 8822c

* add support for WIPHY_WOWLAN_NET_DETECT

brcmfmac

* add initial support for monitor mode

qtnfmac

* add module parameter to enable DFS offloading in firmware

* add support for STA HE rates

* add support for TWT responder and spatial reuse
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2020-01-26

Here's (probably) the last bluetooth-next pull request for the 5.6 kernel.

 - Initial pieces of Bluetooth 5.2 Isochronous Channels support
 - mgmt: Various cleanups and a new Set Blocked Keys command
 - btusb: Added support for 04ca:3021 QCA_ROME device
 - hci_qca: Multiple fixes & cleanups
 - hci_bcm: Fixes & improved device tree support
 - Fixed attempts to create duplicate debugfs entries

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

'alloc_etherdev_mqs()' expects first 'tx', then 'rx'. The semantic here
looks reversed.

Reorder the arguments passed to 'alloc_etherdev_mqs()' in order to keep
the correct semantic.

In fact, this is a no-op because both XGENE_NUM_[RT]X_RING are 8.

Fixes: 107dec27 ("drivers: net: xgene: Add support for multiple queues")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Defaults for min_mtu and max_mtu are set by ether_setup(), which is
called from devm_alloc_etherdev(). Let rtl_jumbo_max() only return
a positive value if actually jumbo packets are supported. This also
allows to remove constant Jumbo_1K which is a little misleading anyway.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

An 'alloc_etherdev()' called is not ballanced by a corresponding
'free_netdev()' call in one error handling path.

Slighly reorder the error handling code to catch the missed case.

Fixes: c100e47c ("mlxsw: minimal: Add ethtool support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DSA sets up a switch tree little by little. Every switch of the N
members of the tree calls dsa_register_switch, and (N - 1) will just
touch the dst->ports list with their ports and quickly exit. Only the
last switch that calls dsa_register_switch will find all DSA links
complete in dsa_tree_setup_routing_table, and not return zero as a
result but instead go ahead and set up the entire DSA switch tree
(practically on behalf of the other switches too).

The trouble is that the (N - 1) switches don't clean up after themselves
after they get an error such as EPROBE_DEFER. Their footprint left in
dst->ports by dsa_switch_touch_ports is still there. And switch N, the
one responsible with actually setting up the tree, is going to work with
those stale dp, dp->ds and dp->ds->dev pointers. In particular ds and
ds->dev might get freed by the device driver.

Be there a 2-switch tree and the following calling order:
- Switch 1 calls dsa_register_switch
  - Calls dsa_switch_touch_ports, populates dst->ports
  - Calls dsa_port_parse_cpu, gets -EPROBE_DEFER, exits.
- Switch 2 calls dsa_register_switch
  - Calls dsa_switch_touch_ports, populates dst->ports
  - Probe doesn't get deferred, so it goes ahead.
  - Calls dsa_tree_setup_routing_table, which returns "complete == true"
    due to Switch 1 having called dsa_switch_touch_ports before.
  - Because the DSA links are complete, it calls dsa_tree_setup_switches
    now.
  - dsa_tree_setup_switches iterates through dst->ports, initializing
    the Switch 1 ds structure (invalid) and the Switch 2 ds structure
    (valid).
  - Undefined behavior (use after free, sometimes NULL pointers, etc).

Real example below (debugging prints added by me, as well as guards
against NULL pointers):

[    5.477947] dsa_tree_setup_switches: Setting up port 0 of switch ffffff803df0b980 (dev ffffff803f775c00)
[    6.313002] dsa_tree_setup_switches: Setting up port 1 of switch ffffff803df0b980 (dev ffffff803f775c00)
[    6.319932] dsa_tree_setup_switches: Setting up port 2 of switch ffffff803df0b980 (dev ffffff803f775c00)
[    6.329693] dsa_tree_setup_switches: Setting up port 3 of switch ffffff803df0b980 (dev ffffff803f775c00)
[    6.339458] dsa_tree_setup_switches: Setting up port 4 of switch ffffff803df0b980 (dev ffffff803f775c00)
[    6.349226] dsa_tree_setup_switches: Setting up port 5 of switch ffffff803df0b980 (dev ffffff803f775c00)
[    6.358991] dsa_tree_setup_switches: Setting up port 6 of switch ffffff803df0b980 (dev ffffff803f775c00)
[    6.368758] dsa_tree_setup_switches: Setting up port 7 of switch ffffff803df0b980 (dev ffffff803f775c00)
[    6.378524] dsa_tree_setup_switches: Setting up port 8 of switch ffffff803df0b980 (dev ffffff803f775c00)
[    6.388291] dsa_tree_setup_switches: Setting up port 9 of switch ffffff803df0b980 (dev ffffff803f775c00)
[    6.398057] dsa_tree_setup_switches: Setting up port 10 of switch ffffff803df0b980 (dev ffffff803f775c00)
[    6.407912] dsa_tree_setup_switches: Setting up port 0 of switch ffffff803da02f80 (dev 0000000000000000)
[    6.417682] dsa_tree_setup_switches: Setting up port 1 of switch ffffff803da02f80 (dev 0000000000000000)
[    6.427446] dsa_tree_setup_switches: Setting up port 2 of switch ffffff803da02f80 (dev 0000000000000000)
[    6.437212] dsa_tree_setup_switches: Setting up port 3 of switch ffffff803da02f80 (dev 0000000000000000)
[    6.446979] dsa_tree_setup_switches: Setting up port 4 of switch ffffff803da02f80 (dev 0000000000000000)
[    6.456744] dsa_tree_setup_switches: Setting up port 5 of switch ffffff803da02f80 (dev 0000000000000000)
[    6.466512] dsa_tree_setup_switches: Setting up port 6 of switch ffffff803da02f80 (dev 0000000000000000)
[    6.476277] dsa_tree_setup_switches: Setting up port 7 of switch ffffff803da02f80 (dev 0000000000000000)
[    6.486043] dsa_tree_setup_switches: Setting up port 8 of switch ffffff803da02f80 (dev 0000000000000000)
[    6.495810] dsa_tree_setup_switches: Setting up port 9 of switch ffffff803da02f80 (dev 0000000000000000)
[    6.505577] dsa_tree_setup_switches: Setting up port 10 of switch ffffff803da02f80 (dev 0000000000000000)
[    6.515433] dsa_tree_setup_switches: Setting up port 0 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[    7.354120] dsa_tree_setup_switches: Setting up port 1 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[    7.361045] dsa_tree_setup_switches: Setting up port 2 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[    7.370805] dsa_tree_setup_switches: Setting up port 3 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[    7.380571] dsa_tree_setup_switches: Setting up port 4 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[    7.390337] dsa_tree_setup_switches: Setting up port 5 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[    7.400104] dsa_tree_setup_switches: Setting up port 6 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[    7.409872] dsa_tree_setup_switches: Setting up port 7 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[    7.419637] dsa_tree_setup_switches: Setting up port 8 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[    7.429403] dsa_tree_setup_switches: Setting up port 9 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[    7.439169] dsa_tree_setup_switches: Setting up port 10 of switch ffffff803db15b80 (dev ffffff803d8e4800)

The solution is to recognize that the functions that call
dsa_switch_touch_ports (dsa_switch_parse_of, dsa_switch_parse) have side
effects, and therefore one should clean up their side effects on error
path. The cleanup of dst->ports was taken from dsa_switch_remove and
moved into a dedicated dsa_switch_release_ports function, which should
really be per-switch (free only the members of dst->ports that are also
members of ds, instead of all switch ports).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All usage of this function was removed three years ago, and the
function was marked as deprecated:
a52ad514 ("net: deprecate eth_change_mtu, remove usage")
So I think we can remove it now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lorenzo Bianconi says:

====================
XDP fixes for socionext driver

Fix possible user-after-in XDP rx path
Fix rx statistics accounting if no bpf program is attached
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix xdp_result initialization in netsec_process_rx in order to not
increase rx counters if there is no bpf program attached to the xdp hook
and napi_gro_receive returns GRO_DROP

Fixes: ba2b2321 ("net: netsec: add XDP support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix possible use-after-free in in netsec_process_rx that can occurs if
the first packet is sent to the normal networking stack and the
following one is dropped by the bpf program attached to the xdp hook.
Fix the issue defining the skb pointer in the 'budget' loop

Fixes: ba2b2321 ("net: netsec: add XDP support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
net: allow per-net notifier to follow netdev into namespace

Currently we have per-net notifier, which allows to get only
notifications relevant to particular network namespace. That is enough
for drivers that have netdevs local in a particular namespace (cannot
move elsewhere).

However if netdev can change namespace, per-net notifier cannot be used.
Introduce dev_net variant that is basically per-net notifier with an
extension that re-registers the per-net notifier upon netdev namespace
change. Basically the per-net notifier follows the netdev into
namespace.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Register the dev_net notifier and allow the per-net notifier to follow
the device into different namespace.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce dev_net variants of netdev notifier register/unregister functions
and allow per-net notifier to follow the netdevice into the namespace it is
moved to.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Push the code which is done under rtnl lock in net notifier register and
unregister function into separate helpers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function does the same thing as the existing code, so rather call
call_netdevice_unregister_net_notifiers() instead of code duplication.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

reuseport_grow() does not need to initialize the more_reuse->max_socks
again. It is already initialized in __reuseport_alloc().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
Support fraglist GRO/GSO

This patchset adds support to do GRO/GSO by chaining packets
of the same flow at the SKB frag_list pointer. This avoids
the overhead to merge payloads into one big packet, and
on the other end, if GSO is needed it avoids the overhead
of splitting the big packet back to the native form.

Patch 1 adds netdev feature flags to enable fraglist GRO,
this implements one of the configuration options discussed
at netconf 2019.

Patch 2 adds a netdev software feature set that defaults to off
and assigns the new fraglist GRO feature flag to it.

Patch 3 adds the core infrastructure to do fraglist GRO/GSO.

Patch 4 enables UDP to use fraglist GRO/GSO if configured.

I have only meaningful forwarding performance measurements.
I did some tests for the local receive path with netperf and iperf,
but in this case the sender that generates the packets is the
bottleneck. So the benchmarks are not that meaningful for the
receive path.

Paolo Abeni did some benchmarks of the local receive path for the
RFC v2 version of this pachset, results can be found here:

https://www.spinics.net/lists/netdev/msg551158.html

I used my IPsec forwarding test setup for the performance measurements:

           ------------         ------------
        -->| router 1 |-------->| router 2 |--
        |  ------------         ------------  |
        |                                     |
        |       --------------------          |
        --------|Spirent Testcenter|<----------
                --------------------

net-next (September 7th 2019):

Single stream UDP frame size 1460 Bytes: 1.161.000 fps (13.5 Gbps).

----------------------------------------------------------------------

net-next (September 7th 2019) + standard UDP GRO/GSO (not implemented
in this patchset):

Single stream UDP frame size 1460 Bytes: 1.801.000 fps (21 Gbps).

----------------------------------------------------------------------

net-next (September 7th 2019) + fraglist UDP GRO/GSO:

Single stream UDP frame size 1460 Bytes: 2.860.000 fps (33.4 Gbps).

=======================================================================

net-next (January 23th 2020):

Single stream UDP frame size 1460 Bytes: 919.000 fps (10.73 Gbps).

----------------------------------------------------------------------

net-next (January 23th 2020) + fraglist UDP GRO/GSO:

Single stream UDP frame size 1460 Bytes: 2.430.000 fps (28.38 Gbps).

-----------------------------------------------------------------------

Changes from RFC v1:

- Add IPv6 support.
- Split patchset to enable UDP GRO by default before adding
  fraglist GRO support.
- Mark fraglist GRO packets as CHECKSUM_NONE.
- Take a refcount on the first segment skb when doing fraglist
  segmentation. With this we can use the same error handling
  path as with standard segmentation.

Changes from RFC v2:

- Add a netdev feature flag to configure listifyed GRO.
- Fix UDP GRO enabling for IPv6.
- Fix a rcu_read_lock() imbalance.
- Fix error path in skb_segment_list().

Changes from RFC v3:

- Rename NETIF_F_GRO_LIST to NETIF_F_GRO_FRAGLIST and add
  NETIF_F_GSO_FRAGLIST.
- Move introduction of SKB_GSO_FRAGLIST to patch 2.
- Use udpv6_encap_needed_key instead of udp_encap_needed_key in IPv6.
- Move some missplaced code from patch 5 to patch 1 where it belongs to.

Changes from RFC v4:

- Drop the 'UDP: enable GRO by default' patch for now. Standard UDP GRO
  is not changed with this patchset.
- Rebase to net-next current.

Changes fom v1 (December 18th):

- Do a full __copy_skb_header instead of tryng to find the really
  needed subset header fields. Thisa can be done later.
- Mark all fraglist GRO packets with CHECKSUM_UNNECESSARY.
- Rebase to net-next current.

Changes fom v2 (January 24th):

- Do the CHECKSUM_UNNECESSARY setting from IPv4 for IPv6 too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch extends UDP GRO to support fraglist GRO/GSO
by using the previously introduced infrastructure.
If the feature is enabled, all UDP packets are going to
fraglist GRO (local input and forward).

After validating the csum,  we mark ip_summed as
CHECKSUM_UNNECESSARY for fraglist GRO packets to
make sure that the csum is not touched.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the core functions to chain/unchain
GSO skbs at the frag_list pointer. This also adds
a new GSO type SKB_GSO_FRAGLIST and a is_flist
flag to napi_gro_cb which indicates that this
flow will be GROed by fraglist chaining.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous patch added the NETIF_F_GRO_FRAGLIST feature.
This is a software feature that should default to off.
Current software features default to on, so add a new
feature set that defaults to off.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds new Fraglist GRO/GSO feature flags. They will be used
to configure fraglist GRO/GSO what will be implemented with some
followup paches.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recently XDP Support was added to the mvneta driver
for software buffer management only.
It is still possible to attach an XDP program if
hardware buffer management is used.
It is not doing anything at that point.

The patch disallows attaching XDP programs to mvneta
if hardware buffer management is used.

I am sorry about that. It is my first submission and I am having
some troubles with the format of my emails.

v4 -> v5:
- Remove extra tabs

v3 -> v4:
- Please ignore v3 I accidentally submitted
  my other patch with git-send-mail and v4 is correct

v2 -> v3:
- My mailserver corrupted the patch
  resubmission with git-send-email

v1 -> v2:
- Fixing the patches indentation
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The subpacket scanning loop in rxrpc_receive_data() references the
subpacket count in the private data part of the sk_buff in the loop
termination condition.  However, when the final subpacket is pasted into
the ring buffer, the function is no longer has a ref on the sk_buff and
should not be looking at sp->* any more.  This point is actually marked in
the code when skb is cleared (but sp is not - which is an error).

Fix this by caching sp->nr_subpackets in a local variable and using that
instead.

Also clear 'sp' to catch accesses after that point.

This can show up as an oops in rxrpc_get_skb() if sp->nr_subpackets gets
trashed by the sk_buff getting freed and reused in the meantime.

Fixes: e2de6c40 ("rxrpc: Use info in skbuff instead of reparsing a jumbo packet")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is possible for malicious userspace to set TCF_EM_SIMPLE bit
even for matches that should not have this bit set.

This can fool two places using tcf_em_is_simple()

1) tcf_em_tree_destroy() -> memory leak of em->data
   if ops->destroy() is NULL

2) tcf_em_tree_dump() wrongly report/leak 4 low-order bytes
   of a kernel pointer.

BUG: memory leak
unreferenced object 0xffff888121850a40 (size 32):
  comm "syz-executor927", pid 7193, jiffies 4294941655 (age 19.840s)
  hex dump (first 32 bytes):
    00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<00000000f67036ea>] kmemleak_alloc_recursive include/linux/kmemleak.h:43 [inline]
    [<00000000f67036ea>] slab_post_alloc_hook mm/slab.h:586 [inline]
    [<00000000f67036ea>] slab_alloc mm/slab.c:3320 [inline]
    [<00000000f67036ea>] __do_kmalloc mm/slab.c:3654 [inline]
    [<00000000f67036ea>] __kmalloc_track_caller+0x165/0x300 mm/slab.c:3671
    [<00000000fab0cc8e>] kmemdup+0x27/0x60 mm/util.c:127
    [<00000000d9992e0a>] kmemdup include/linux/string.h:453 [inline]
    [<00000000d9992e0a>] em_nbyte_change+0x5b/0x90 net/sched/em_nbyte.c:32
    [<000000007e04f711>] tcf_em_validate net/sched/ematch.c:241 [inline]
    [<000000007e04f711>] tcf_em_tree_validate net/sched/ematch.c:359 [inline]
    [<000000007e04f711>] tcf_em_tree_validate+0x332/0x46f net/sched/ematch.c:300
    [<000000007a769204>] basic_set_parms net/sched/cls_basic.c:157 [inline]
    [<000000007a769204>] basic_change+0x1d7/0x5f0 net/sched/cls_basic.c:219
    [<00000000e57a5997>] tc_new_tfilter+0x566/0xf70 net/sched/cls_api.c:2104
    [<0000000074b68559>] rtnetlink_rcv_msg+0x3b2/0x4b0 net/core/rtnetlink.c:5415
    [<00000000b7fe53fb>] netlink_rcv_skb+0x61/0x170 net/netlink/af_netlink.c:2477
    [<00000000e83a40d0>] rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5442
    [<00000000d62ba933>] netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
    [<00000000d62ba933>] netlink_unicast+0x223/0x310 net/netlink/af_netlink.c:1328
    [<0000000088070f72>] netlink_sendmsg+0x2c0/0x570 net/netlink/af_netlink.c:1917
    [<00000000f70b15ea>] sock_sendmsg_nosec net/socket.c:639 [inline]
    [<00000000f70b15ea>] sock_sendmsg+0x54/0x70 net/socket.c:659
    [<00000000ef95a9be>] ____sys_sendmsg+0x2d0/0x300 net/socket.c:2330
    [<00000000b650f1ab>] ___sys_sendmsg+0x8a/0xd0 net/socket.c:2384
    [<0000000055bfa74a>] __sys_sendmsg+0x80/0xf0 net/socket.c:2417
    [<000000002abac183>] __do_sys_sendmsg net/socket.c:2426 [inline]
    [<000000002abac183>] __se_sys_sendmsg net/socket.c:2424 [inline]
    [<000000002abac183>] __x64_sys_sendmsg+0x23/0x30 net/socket.c:2424

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+03c4738ed29d5d366ddf@syzkaller.appspotmail.com
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Include the size of struct nhmsg size when calculating
how much of a payload to allocate in a new netlink nexthop
notification message.

Without this, we will fail to fill the skbuff at certain nexthop
group sizes.

You can reproduce the failure with the following iproute2 commands:

ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link add dummy3 type dummy
ip link add dummy4 type dummy
ip link add dummy5 type dummy
ip link add dummy6 type dummy
ip link add dummy7 type dummy
ip link add dummy8 type dummy
ip link add dummy9 type dummy
ip link add dummy10 type dummy
ip link add dummy11 type dummy
ip link add dummy12 type dummy
ip link add dummy13 type dummy
ip link add dummy14 type dummy
ip link add dummy15 type dummy
ip link add dummy16 type dummy
ip link add dummy17 type dummy
ip link add dummy18 type dummy
ip link add dummy19 type dummy

ip ro add 1.1.1.1/32 dev dummy1
ip ro add 1.1.1.2/32 dev dummy2
ip ro add 1.1.1.3/32 dev dummy3
ip ro add 1.1.1.4/32 dev dummy4
ip ro add 1.1.1.5/32 dev dummy5
ip ro add 1.1.1.6/32 dev dummy6
ip ro add 1.1.1.7/32 dev dummy7
ip ro add 1.1.1.8/32 dev dummy8
ip ro add 1.1.1.9/32 dev dummy9
ip ro add 1.1.1.10/32 dev dummy10
ip ro add 1.1.1.11/32 dev dummy11
ip ro add 1.1.1.12/32 dev dummy12
ip ro add 1.1.1.13/32 dev dummy13
ip ro add 1.1.1.14/32 dev dummy14
ip ro add 1.1.1.15/32 dev dummy15
ip ro add 1.1.1.16/32 dev dummy16
ip ro add 1.1.1.17/32 dev dummy17
ip ro add 1.1.1.18/32 dev dummy18
ip ro add 1.1.1.19/32 dev dummy19

ip next add id 1 via 1.1.1.1 dev dummy1
ip next add id 2 via 1.1.1.2 dev dummy2
ip next add id 3 via 1.1.1.3 dev dummy3
ip next add id 4 via 1.1.1.4 dev dummy4
ip next add id 5 via 1.1.1.5 dev dummy5
ip next add id 6 via 1.1.1.6 dev dummy6
ip next add id 7 via 1.1.1.7 dev dummy7
ip next add id 8 via 1.1.1.8 dev dummy8
ip next add id 9 via 1.1.1.9 dev dummy9
ip next add id 10 via 1.1.1.10 dev dummy10
ip next add id 11 via 1.1.1.11 dev dummy11
ip next add id 12 via 1.1.1.12 dev dummy12
ip next add id 13 via 1.1.1.13 dev dummy13
ip next add id 14 via 1.1.1.14 dev dummy14
ip next add id 15 via 1.1.1.15 dev dummy15
ip next add id 16 via 1.1.1.16 dev dummy16
ip next add id 17 via 1.1.1.17 dev dummy17
ip next add id 18 via 1.1.1.18 dev dummy18
ip next add id 19 via 1.1.1.19 dev dummy19

ip next add id 1111 group 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16/17/18/19
ip next del id 1111

Fixes: 430a0491 ("nexthop: Add support for nexthop groups")
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In a complex TC class hierarchy like this:

tc qdisc add dev eth0 root handle 1:0 cbq bandwidth 100Mbit         \
  avpkt 1000 cell 8
tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 100Mbit  \
  rate 6Mbit weight 0.6Mbit prio 8 allot 1514 cell 8 maxburst 20      \
  avpkt 1000 bounded

tc filter add dev eth0 parent 1:0 protocol ip prio 1 u32 match ip \
  sport 80 0xffff flowid 1:3
tc filter add dev eth0 parent 1:0 protocol ip prio 1 u32 match ip \
  sport 25 0xffff flowid 1:4

tc class add dev eth0 parent 1:1 classid 1:3 cbq bandwidth 100Mbit  \
  rate 5Mbit weight 0.5Mbit prio 5 allot 1514 cell 8 maxburst 20      \
  avpkt 1000
tc class add dev eth0 parent 1:1 classid 1:4 cbq bandwidth 100Mbit  \
  rate 3Mbit weight 0.3Mbit prio 5 allot 1514 cell 8 maxburst 20      \
  avpkt 1000

where filters are installed on qdisc 1:0, so we can't merely
search from class 1:1 when creating class 1:3 and class 1:4. We have
to walk through all the child classes of the direct parent qdisc.
Otherwise we would miss filters those need reverse binding.

Fixes: 07d79fc7 ("net_sched: add reverse binding for tc class")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current implementations of ops->bind_class() are merely
searching for classid and updating class in the struct tcf_result,
without invoking either of cl_ops->bind_tcf() or
cl_ops->unbind_tcf(). This breaks the design of them as qdisc's
like cbq use them to count filters too. This is why syzbot triggered
the warning in cbq_destroy_class().

In order to fix this, we have to call cl_ops->bind_tcf() and
cl_ops->unbind_tcf() like the filter binding path. This patch does
so by refactoring out two helper functions __tcf_bind_filter()
and __tcf_unbind_filter(), which are lockless and accept a Qdisc
pointer, then teaching each implementation to call them correctly.

Note, we merely pass the Qdisc pointer as an opaque pointer to
each filter, they only need to pass it down to the helper
functions without understanding it at all.

Fixes: 07d79fc7 ("net_sched: add reverse binding for tc class")
Reported-and-tested-by: syzbot+0a0596220218fcb603a8@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+63bdb6006961d8c917c6@syzkaller.appspotmail.com
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

This batch contains Netfilter updates for net-next:

1) Add nft_setelem_parse_key() helper function.

2) Add NFTA_SET_ELEM_KEY_END to specify a range with one single element.

3) Add NFTA_SET_DESC_CONCAT to describe the set element concatenation,
   from Stefano Brivio.

4) Add bitmap_cut() to copy n-bits from source to destination,
   from Stefano Brivio.

5) Add set to match on arbitrary concatenations, from Stefano Brivio.

6) Add selftest for this new set type. An extract of Stefano's
   description follows:

"Existing nftables set implementations allow matching entries with
interval expressions (rbtree), e.g. 192.0.2.1-192.0.2.4, entries
specifying field concatenation (hash, rhash), e.g. 192.0.2.1:22,
but not both.

In other words, none of the set types allows matching on range
expressions for more than one packet field at a time, such as ipset
does with types bitmap:ip,mac, and, to a more limited extent
(netmasks, not arbitrary ranges), with types hash:net,net,
hash:net,port, hash:ip,port,net, and hash:net,port,net.

As a pure hash-based approach is unsuitable for matching on ranges,
and "proxying" the existing red-black tree type looks impractical as
elements would need to be shared and managed across all employed
trees, this new set implementation intends to fill the functionality
gap by employing a relatively novel approach.

The fundamental idea, illustrated in deeper detail in patch 5/9, is to
use lookup tables classifying a small number of grouped bits from each
field, and map the lookup results in a way that yields a verdict for
the full set of specified fields.

The grouping bit aspect is loosely inspired by the Grouper algorithm,
by Jay Ligatti, Josh Kuhn, and Chris Gage (see patch 5/9 for the full
reference).

A reference, stand-alone implementation of the algorithm itself is
available at:
        https://pipapo.lameexcu.se

Some notes about possible future optimisations are also mentioned
there. This algorithm reduces the matching problem to, essentially,
a repetitive sequence of simple bitwise operations, and is
particularly suitable to be optimised by leveraging SIMD instruction
sets."
====================
Signed-off-by: David S. Miller <davem@davemloft.net>