We don't have cpu_is_omapxxxx SoC detection initialized until
SoC detection is initialized from init_early.

Note that with the common map_io we should no longer need
cpu_is_omapxxxx for ioremap.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Otherwise we can't do generic map_io as we currently rely on
static mappings that work only because of arch_ioremap.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This allows us to remove omap hacks for map_io.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This assumes fixed mappings which will not work once we move
to use ioremap_exec(). It seems that these are currently
not in use, or in use for some out of tree corner cases.

If SRAM support for framebuffer is wanted, it should be done
with ioremap in the driver.

Note that further removal of the code can now be done,
but that can be done seprately by the driver maintainers.
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This way we don't need to initialize SoC detection early
and can start using generic map_io.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This allows removing omap hacks for map_io allowing generic
map_io.

Note that in the future we can't do cpu_is_omapxxxx detection
until in init_early. This means that board-innovator.c now
assumes 15xx only, and board-generic.c assumes 16xx only.
This is best fixed later on by passing the SoC type from
device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Move the platform device definitions from boards code to plat-samsung
to avoid multiple instances when multiple board support is compiled in.
The boards should select at least S5P_DEV_FIMC0 to enable FIMC support.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch cleans up the Samsung resources in plat-samsung/devs.c
by using defined helpers at <linux/ioport.h>.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch merges each dev files to one devs.c file in
plat-samsung directory and this help to keep it more
easily to reduce plat- directories such as plat-s3c24xx
and plat-s5p.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch moves regarding s5p dev files to one devs.c file
in plat-samsung directory and this help to keep it more
easily.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch moves regarding s3c64xx dev files to one devs.c
file in plat-samsung directory and this help to keep it more
easily.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch moves regarding s3c24xx dev files to one devs.c
file in plat-samsung directory and this is required to merge
to plat-samsung.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add nodes for devices used by PM code (mpu, dsp, iva).

Add a cpus node as well as recommended in the DT spec.

Remove mpu, dsp, iva devices init if is populated.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Kevin Hilman <khilman@ti.com>

Used the main OCP node to add bindings with the l3_noc driver.
Remove l3_noc static device creation if DT is populated.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>

Add device-tree support for the l3-noc driver.

Use platform_driver_register to defer the probing at device init
time.

Add documentation for the l3-noc bindings.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>

Still needed to boot until the i2c & twl driver is adapted to
device-tree. Otherwise the voltage control code will try to
access the twl and crash.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

Re-cycle the original board-generic.c file to support Device Tree
for every OMAP2+ variants.

The current approach is an intermediate step before having only
one machine descriptor that will use some generic DT aware
functions.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

Add OMAP3 beagleboard DTS file to use the omap3.dtsi SoC file.

Add a default bootargs line to allow a boot from RAMDISK.

Add memory node information.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>

Add initial OMAP3 soc file with empty ocp bus.

Based on initial patch from Manju:
http://www.spinics.net/lists/linux-omap/msg55830.htmlSigned-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>

Add the SDP/Blaze (Software Development Board) support with
device tree.
That file is based on the omap4-panda.dts.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>

Based on the original omap4-panda.dts file from Manju.
http://www.spinics.net/lists/linux-omap/msg55836.html

Add memory information and a default bootargs to allow
a boot from RAMDISK.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>

Add initial device-tree support for OMAP4 SoC.

This is based on the original panda board patch done by Manju:
http://permalink.gmane.org/gmane.linux.ports.arm.omap/60393

Add the generic GIC interrupt-controller from ARM.

Add an empty "soc" node to contain non memory mapped IPs
(DSP, MPU, IPU...).

Note: Since reg, irq and dma are provided by hwmod for the
moment, these attributes will not be present at all in DTS
to highlight the gap. They will be added as soon as dma bindings
will be there and drivers will be adapted.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>

Add a notifier called during device_add phase. If an of_node is present,
retrieve the hwmod entry in order to populate properly the omap_device
structure.

For the moment the resource from the device-tree are overloaded.
DT does not support named resource yet, and thus, most driver will not
work without that information.

Add a documentation to capture the specifics OMAP bindings needed for
device-tree support.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Split the omap_device_build_ss into two smaller functions
that will allow to populate a platform_device already allocated by
device-tree.

The functionality of the omap_device_build_ss is still the same, but
the omap_device_alloc will be usable with devices already built by
device-tree.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Add of_property_read_string_index and of_property_count_strings
to retrieve one string inside a property that will contains
severals strings.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Remove all these duplicated structures since a default one is now
available.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Most devices are using the same default omap_device_pm_latency structure
during device built. In order to avoid the duplication of the same
structure everywhere, add a default structure that will be used if
the device does not have an explicit one.

Next patches will clean the duplicated structures.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Since the device pointer is now retrieved using the hwmod name, remove
the static variables used to store the device pointers for DSP, MPU, IVA
and L3 devices for PM/DVFS usage.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Replace the struct device parameter of omap2_set_init_voltage
by the hwmod name. It will avoid having to store explicitely
the device pointer into a static variable.

Moreover, it will be a little bit more scalable if we introduce
new DVFS devices.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Replace the multiple omap2_get_XXX_device APIs with the new
omap_hwmod_name_get_dev that uses the hwmod name to get the proper
device.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

An API which translates a standard hwmod name to corresponding
platform_device is useful for drivers when they need to look up the
device associated with a hwmod name to map back into the device
structure pointers. These ideally should be used by drivers in
mach directory. Using a generic hwmod name like "gpu" instead of
the actual device name which could change in the future, allows
us to:
a) Could in effect help replace apis such as omap2_get_mpuss_device,
omap2_get_iva_device, omap2_get_l3_device, omap4_get_dsp_device,
etc..
b) Scale to more devices rather than be restricted to named functions
c) Simplify driver's platform_data from passing additional fields
all doing the same thing with different function pointer names
just for accessing a different device name.
Signed-off-by: Nishanth Menon <nm@ti.com>
[b-cousson@ti.com: Adapt it to the new pdev pointer inside od,
remove the unneeded helpers, and fold the next patch here]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Add suspend-to-ram support for SMDK6440/50
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The sleep code for S5PV210 and EXYNOS4 are identical; moreover
S5p64X0 and S5PC100 for which support will be added soon can
use the same procedure. Create a common sleep code in the plat-s5p
directory so that it can be re-used.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Pave the way for adding PM support on S5P64X0, which is more similar
to the S3C64XX series than the S5P series. Hence, the common pm code
(containing dummy functions) should not be used for S5P64X0.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Conflicts:
	arch/arm/plat-s5p/include/plat/pll.h

Conflicts:
	arch/arm/mach-exynos4/clock.c
	arch/arm/mach-s3c2412/gpio.c
	arch/arm/mach-s5p64x0/dma.c
	arch/arm/mach-s5p64x0/gpiolib.c