- 10 Jun, 2016 28 commits
-
-
David Müller authored
commit 6f210c18 upstream. Since commit 21947ba6 ("serial: 8250_pci: replace switch-case by formula"), the 8250 driver crashes in the byt_set_termios() function with a divide error. This is caused by the fact that a baud rate of 0 (B0) is not handled properly. Fix it by falling back to B9600 in this case. Signed-off-by:
David Müller <d.mueller@elsoft.ch> Fixes: 21947ba6 ("serial: 8250_pci: replace switch-case by formula") Suggested-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Chris Bainbridge authored
commit feb26ac3 upstream. The XHCI controller presents two USB buses to the system - one for USB2 and one for USB3. The hub init code (hub_port_init) is reentrant but only locks one bus per thread, leading to a race condition failure when two threads attempt to simultaneously initialise a USB2 and USB3 device: [ 8.034843] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command [ 13.183701] usb 3-3: device descriptor read/all, error -110 On a test system this failure occurred on 6% of all boots. The call traces at the point of failure are: Call Trace: [<ffffffff81b9bab7>] schedule+0x37/0x90 [<ffffffff817da7cd>] usb_kill_urb+0x8d/0xd0 [<ffffffff8111e5e0>] ? wake_up_atomic_t+0x30/0x30 [<ffffffff817dafbe>] usb_start_wait_urb+0xbe/0x150 [<ffffffff817db10c>] usb_control_msg+0xbc/0xf0 [<ffffffff817d07de>] hub_port_init+0x51e/0xb70 [<ffffffff817d4697>] hub_event+0x817/0x1570 [<ffffffff810f3e6f>] process_one_work+0x1ff/0x620 [<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620 [<ffffffff810f4684>] worker_thread+0x64/0x4b0 [<ffffffff810f4620>] ? rescuer_thread+0x390/0x390 [<ffffffff810fa7f5>] kthread+0x105/0x120 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200 [<ffffffff81ba183f>] ret_from_fork+0x3f/0x70 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200 Call Trace: [<ffffffff817fd36d>] xhci_setup_device+0x53d/0xa40 [<ffffffff817fd87e>] xhci_address_device+0xe/0x10 [<ffffffff817d047f>] hub_port_init+0x1bf/0xb70 [<ffffffff811247ed>] ? trace_hardirqs_on+0xd/0x10 [<ffffffff817d4697>] hub_event+0x817/0x1570 [<ffffffff810f3e6f>] process_one_work+0x1ff/0x620 [<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620 [<ffffffff810f4684>] worker_thread+0x64/0x4b0 [<ffffffff810f4620>] ? rescuer_thread+0x390/0x390 [<ffffffff810fa7f5>] kthread+0x105/0x120 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200 [<ffffffff81ba183f>] ret_from_fork+0x3f/0x70 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200 Which results from the two call chains: hub_port_init usb_get_device_descriptor usb_get_descriptor usb_control_msg usb_internal_control_msg usb_start_wait_urb usb_submit_urb / wait_for_completion_timeout / usb_kill_urb hub_port_init hub_set_address xhci_address_device xhci_setup_device Mathias Nyman explains the current behaviour violates the XHCI spec: hub_port_reset() will end up moving the corresponding xhci device slot to default state. As hub_port_reset() is called several times in hub_port_init() it sounds reasonable that we could end up with two threads having their xhci device slots in default state at the same time, which according to xhci 4.5.3 specs still is a big no no: "Note: Software shall not transition more than one Device Slot to the Default State at a time" So both threads fail at their next task after this. One fails to read the descriptor, and the other fails addressing the device. Fix this in hub_port_init by locking the USB controller (instead of an individual bus) to prevent simultaneous initialisation of both buses. Fixes: 638139eb ("usb: hub: allow to process more usb hub events in parallel") Link: https://lkml.org/lkml/2016/2/8/312 Link: https://lkml.org/lkml/2016/2/4/748Signed-off-by:
Chris Bainbridge <chris.bainbridge@gmail.com> Acked-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Luke Dashjr authored
commit 4c63c245 upstream. 32-bit ioctl uses these rather than the regular FS_IOC_* versions. They can be handled in btrfs using the same code. Without this, 32-bit {ch,ls}attr fail. Signed-off-by:
Luke Dashjr <luke-jr+git@utopios.org> Reviewed-by:
Josef Bacik <jbacik@fb.com> Reviewed-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Andrew Jeffery authored
commit 71324fdc upstream. The range is registered into a linked list which can be referenced throughout the lifetime of the driver. Ensure the range's memory is useful for the same lifetime by adding it to the driver's private data structure. The bug was introduced in the driver's initial commit, which was present in v3.10. Fixes: f0b9a7e5 ("pinctrl: exynos5440: add pinctrl driver for Samsung EXYNOS5440 SoC") Signed-off-by:
Andrew Jeffery <andrew@aj.id.au> Acked-by:
Tomasz Figa <tomasz.figa@gmail.com> Reviewed-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Vittorio Gambaletta (VittGam) authored
commit 0f9edcdd upstream. The Wistron DNMA-92 and Compex WLM200NX have inverted LED polarity (active high instead of active low). The same PCI Subsystem ID is used by both cards, which are based on the same Atheros MB92 design. Cc: <linux-wireless@vger.kernel.org> Cc: <ath9k-devel@qca.qualcomm.com> Cc: <ath9k-devel@lists.ath9k.org> Signed-off-by:
Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
-
Vittorio Gambaletta (VittGam) authored
commit cd84042c upstream. The LED can be active high instead of active low on some hardware. Add the led_active_high module parameter. It defaults to -1 to obey platform data as before. Setting the parameter to 1 or 0 will force the LED respectively active high or active low. Cc: <linux-wireless@vger.kernel.org> Cc: <ath9k-devel@qca.qualcomm.com> Cc: <ath9k-devel@lists.ath9k.org> Signed-off-by:
-
Krzysztof Kozlowski authored
commit 79152e8d upstream. The tcrypt testing module on Exynos5422-based Odroid XU3/4 board failed on testing 8 kB size blocks: $ sudo modprobe tcrypt sec=1 mode=500 testing speed of async ecb(aes) (ecb-aes-s5p) encryption test 0 (128 bit key, 16 byte blocks): 21971 operations in 1 seconds (351536 bytes) test 1 (128 bit key, 64 byte blocks): 21731 operations in 1 seconds (1390784 bytes) test 2 (128 bit key, 256 byte blocks): 21932 operations in 1 seconds (5614592 bytes) test 3 (128 bit key, 1024 byte blocks): 21685 operations in 1 seconds (22205440 bytes) test 4 (128 bit key, 8192 byte blocks): This was caused by a race issue of missed BRDMA_DONE ("Block cipher Receiving DMA") interrupt. Device starts processing the data in DMA mode immediately after setting length of DMA block: receiving (FCBRDMAL) or transmitting (FCBTDMAL). The driver sets these lengths from interrupt handler through s5p_set_dma_indata() function (or xxx_setdata()). However the interrupt handler was first dealing with receive buffer (dma-unmap old, dma-map new, set receive block length which starts the operation), then with transmit buffer and finally was clearing pending interrupts (FCINTPEND). Because of the time window between setting receive buffer length and clearing pending interrupts, the operation on receive buffer could end already and driver would miss new interrupt. User manual for Exynos5422 confirms in example code that setting DMA block lengths should be the last operation. The tcrypt hang could be also observed in following blocked-task dmesg: INFO: task modprobe:258 blocked for more than 120 seconds. Not tainted 4.6.0-rc4-next-20160419-00005-g9eac8b7b7753-dirty #42 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. modprobe D c06b09d8 0 258 256 0x00000000 [<c06b09d8>] (__schedule) from [<c06b0f24>] (schedule+0x40/0xac) [<c06b0f24>] (schedule) from [<c06b49f8>] (schedule_timeout+0x124/0x178) [<c06b49f8>] (schedule_timeout) from [<c06b17fc>] (wait_for_common+0xb8/0x144) [<c06b17fc>] (wait_for_common) from [<bf0013b8>] (test_acipher_speed+0x49c/0x740 [tcrypt]) [<bf0013b8>] (test_acipher_speed [tcrypt]) from [<bf003e8c>] (do_test+0x2240/0x30ec [tcrypt]) [<bf003e8c>] (do_test [tcrypt]) from [<bf008048>] (tcrypt_mod_init+0x48/0xa4 [tcrypt]) [<bf008048>] (tcrypt_mod_init [tcrypt]) from [<c010177c>] (do_one_initcall+0x3c/0x16c) [<c010177c>] (do_one_initcall) from [<c0191ff0>] (do_init_module+0x5c/0x1ac) [<c0191ff0>] (do_init_module) from [<c0185610>] (load_module+0x1a30/0x1d08) [<c0185610>] (load_module) from [<c0185ab0>] (SyS_finit_module+0x8c/0x98) [<c0185ab0>] (SyS_finit_module) from [<c01078c0>] (ret_fast_syscall+0x0/0x3c) Fixes: a49e490c ("crypto: s5p-sss - add S5PV210 advanced crypto engine support") Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> [ kamal: backport to 4.2-stable: context ] Signed-off-by:
-
Ulf Hansson authored
commit 0ae3aeef upstream. As pm_runtime_set_active() may fail because the device's parent isn't active, we can end up executing the ->runtime_resume() callback for the device when it isn't allowed. Fix this by invoking pm_runtime_set_active() before running the callback and let's also deal with the error code. Fixes: 37f20416 (PM: Add pm_runtime_suspend|resume_force functions) Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Hari Bathini authored
commit 8ed8ab40 upstream. Some of the interrupt vectors on 64-bit POWER server processors are only 32 bytes long (8 instructions), which is not enough for the full first-level interrupt handler. For these we need to branch to an out-of-line (OOL) handler. But when we are running a relocatable kernel, interrupt vectors till __end_interrupts marker are copied down to real address 0x100. So, branching to labels (ie. OOL handlers) outside this section must be handled differently (see LOAD_HANDLER()), considering relocatable kernel, which would need at least 4 instructions. However, branching from interrupt vector means that we corrupt the CFAR (come-from address register) on POWER7 and later processors as mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions) that contains the part up to the point where the CFAR is saved in the PACA should be part of the short interrupt vectors before we branch out to OOL handlers. But as mentioned already, there are interrupt vectors on 64-bit POWER server processors that are only 32 bytes long (like vectors 0x4f00, 0x4f20, etc.), which cannot accomodate the above two cases at the same time owing to space constraint. Currently, in these interrupt vectors, we simply branch out to OOL handlers, without using LOAD_HANDLER(), which leaves us vulnerable when running a relocatable kernel (eg. kdump case). While this has been the case for sometime now and kdump is used widely, we were fortunate not to see any problems so far, for three reasons: 1. In almost all cases, production kernel (relocatable) is used for kdump as well, which would mean that crashed kernel's OOL handler would be at the same place where we end up branching to, from short interrupt vector of kdump kernel. 2. Also, OOL handler was unlikely the reason for crash in almost all the kdump scenarios, which meant we had a sane OOL handler from crashed kernel that we branched to. 3. On most 64-bit POWER server processors, page size is large enough that marking interrupt vector code as executable (see commit 429d2e83) leads to marking OOL handler code from crashed kernel, that sits right below interrupt vector code from kdump kernel, as executable as well. Let us fix this by moving the __end_interrupts marker down past OOL handlers to make sure that we also copy OOL handlers to real address 0x100 when running a relocatable kernel. This fix has been tested successfully in kdump scenario, on an LPAR with 4K page size by using different default/production kernel and kdump kernel. Also tested by manually corrupting the OOL handlers in the first kernel and then kdump'ing, and then causing the OOL handlers to fire - mpe. Fixes: c1fb6816 ("powerpc: Add relocation on exception vector handlers") Signed-off-by:
Hari Bathini <hbathini@linux.vnet.ibm.com> Signed-off-by:
Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Takashi Iwai authored
commit c7c999cb upstream. hci_vhci driver creates a hci device object dynamically upon each HCI_VENDOR_PKT write. Although it checks the already created object and returns an error, it's still racy and may build multiple hci_dev objects concurrently when parallel writes are performed, as the device tracks only a single hci_dev object. This patch introduces a mutex to protect against the concurrent device creations. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Rajkumar Manoharan authored
commit 1ce8c148 upstream. Upon firmware assert, restart work will be triggered so that mac80211 will reconfigure the driver. An issue is reported that after restart work, survey dump data do not contain in-use (SURVEY_INFO_IN_USE) info for operating channel. During reconfigure, since mac80211 already has valid channel context for given radio, channel context iteration return num_chanctx > 0. Hence rx_channel is always NULL. Fix this by assigning channel context to rx_channel when driver restart is in progress. Signed-off-by:
Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by:
-
Akshay Bhat authored
commit 7a18afe8 upstream. On ads7828 the internal reference defaults to off upon power up. When using internal reference, it needs to be turned on and the voltage needs to settle before normal conversion cycle can be started. Hence perform a dummy read in the probe to enable the internal reference allowing the voltage to settle before performing a normal read. Without this fix, the first read from the ADC when using internal reference always returns incorrect data. Signed-off-by:
Akshay Bhat <akshay.bhat@timesys.com> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Michal Nazarewicz authored
commit f78bbcae upstream. When binding the function to usb_configuration, check whether the thread is running before starting another one. Without that, when function instance is added to multiple configurations, fsg_bing starts multiple threads with all but the latest one being forgotten by the driver. This leads to obvious thread leaks, possible lockups when trying to halt the machine and possible more issues. This fixes issues with legacy/multi¹ gadget as well as configfs gadgets when mass_storage function is added to multiple configurations. This change also simplifies API since the legacy gadgets no longer need to worry about starting the thread by themselves (which was where bug in legacy/multi was in the first place). N.B., this patch doesn’t address adding single mass_storage function instance to a single configuration twice. Thankfully, there’s no legitimate reason for such setup plus, if I’m not mistaken, configfs gadget doesn’t even allow it to be expressed. ¹ I have no example failure though. Conclusion that legacy/multi has a bug is based purely on me reading the code. Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Michal Nazarewicz <mina86@mina86.com> Tested-by:
Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> [ kamal: backport to 4.2-stable: fsg_bind() decl 'common'; no change to nokia.c (no fsg_opts) ] Signed-off-by:
-
Jani Nikula authored
commit e6f57789 upstream. Due to "some hardware limitation" the DPI enable bit in port C control register does not get set on VLV. As a workaround we check the status in pipe B conf register instead. The workaround was added in commit c0beefd2 Author: Gaurav K Singh <gaurav.k.singh@intel.com> Date: Tue Dec 9 10:59:20 2014 +0530 drm/i915: Software workaround for getting the HW status of DSI Port C on BYT Empirical evidence (on Surface 3 with DSI on port C per VBT) shows that this is the case also on CHV, so extend the workaround to CHV. We still have the device ready register check in place, so this should not get confused with e.g. HDMI on pipe B. This fixes a number of state checker warnings on CHV DSI port C. Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1460724451-13810-1-git-send-email-jani.nikula@intel.com [ kamal: backport to 4.2-stable: context ] Signed-off-by:
-
Johannes Thumshirn authored
commit 305c2e71 upstream. Now that we've done a more comprehensive fix with the intermediate target state we can remove the previous hack introduced with commit 90a88d6e ("scsi: fix soft lockup in scsi_remove_target() on module removal"). Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by:
Ewan D. Milne <emilne@redhat.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Johannes Thumshirn authored
commit f05795d3 upstream. Add intermediate STARGET_REMOVE state to scsi_target_state to avoid running into the BUG_ON() in scsi_target_reap(). The STARGET_REMOVE state is only valid in the path from scsi_remove_target() to scsi_target_destroy() indicating this target is going to be removed. This re-fixes the problem introduced in commits bc3f02a7 ("[SCSI] scsi_remove_target: fix softlockup regression on hot remove") and 40998193 ("scsi: restart list search after unlock in scsi_remove_target") in a more comprehensive way. [mkp: Included James' fix for scsi_target_destroy()] Signed-off-by:
Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Tested-by:
James Bottomley <jejb@linux.vnet.ibm.com> Signed-off-by:
-
Tiffany Lin authored
commit baf43c6e upstream. In v4l2-compliance utility, test VIDIOC_CREATE_BUFS will check whether reserved filed of v4l2_create_buffers filled with zero Reserved field is filled with zero in v4l_create_bufs. This patch copy reserved field of v4l2_create_buffer from kernel space to user space Signed-off-by:
Tiffany Lin <tiffany.lin@mediatek.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Andy Shevchenko authored
commit 7f0c5ae1 upstream. There is a potential resource leak in case when ->probe() fails. We have to unregister and remove clock tree which is done here. This is a follow up to previously pushed commit c4726abc ("mfd: intel_quark_i2c_gpio: Use clkdev_create()") that prevents double free() when clkdev_drop() followed by kfree() in devm_kcalloc() release stage. I leave Fixes tag here, but the backporting will require to backport the commit c4726abc ("mfd: intel_quark_i2c_gpio: Use clkdev_create()") first. Fixes: 60ae5b9f (mfd: intel_quark_i2c_gpio: Add Intel Quark X1000 I2C-GPIO MFD Driver) Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Stephen Boyd authored
commit c4726abc upstream. Convert this driver to use clkdev_create() instead of clk_register_clkdevs(). The latter API is only used by this driver, although this driver only allocates one clk to add anyway. Furthermore, this driver allocates the clk_lookup structure with devm, but clkdev_drop() will free that structure when passed, leading to a double free when this driver is removed. Clean it all up and pave the way for the removal of clk_register_clkdevs(). Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Russell King <linux@arm.linux.org.uk> Signed-off-by:
-
Dave Gerlach authored
commit c998c078 upstream. Currently the 'registered' member of the cpuidle_device struct is set to 1 during cpuidle_register_device. In this same function there are checks to see if the device is already registered to prevent duplicate calls to register the device, but this value is never set to 0 even on unregister of the device. Because of this, any attempt to call cpuidle_register_device after a call to cpuidle_unregister_device will fail which shouldn't be the case. To prevent this, set registered to 0 when the device is unregistered. Fixes: c878a52d (cpuidle: Check if device is already registered) Signed-off-by:
Dave Gerlach <d-gerlach@ti.com> Acked-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
-
Jiri Slaby authored
commit 13407376 upstream. The write handler allocates skbs and queues them into data->readq. Read side should read them, if there is any. If there is none, skbs should be dropped by hdev->flush. But this happens only if the device is HCI_UP, i.e. hdev->power_on work was triggered already. When it was not, skbs stay allocated in the queue when /dev/vhci is closed. So purge the queue in ->release. Program to reproduce: #include <err.h> #include <fcntl.h> #include <stdio.h> #include <unistd.h> #include <sys/stat.h> #include <sys/types.h> #include <sys/uio.h> int main() { char buf[] = { 0xff, 0 }; struct iovec iov = { .iov_base = buf, .iov_len = sizeof(buf), }; int fd; while (1) { fd = open("/dev/vhci", O_RDWR); if (fd < 0) err(1, "open"); usleep(50); if (writev(fd, &iov, 1) < 0) err(1, "writev"); usleep(50); close(fd); } return 0; } Result: kmemleak: 4609 new suspected memory leaks unreferenced object 0xffff88059f4d5440 (size 232): comm "vhci", pid 1084, jiffies 4294912542 (age 37569.296s) hex dump (first 32 bytes): 20 f0 23 87 05 88 ff ff 20 f0 23 87 05 88 ff ff .#..... .#..... 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: ... [<ffffffff81ece010>] __alloc_skb+0x0/0x5a0 [<ffffffffa021886c>] vhci_create_device+0x5c/0x580 [hci_vhci] [<ffffffffa0219436>] vhci_write+0x306/0x4c8 [hci_vhci] Fixes: 23424c0d (Bluetooth: Add support creating virtual AMP controllers) Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
-
Jiri Slaby authored
commit 373a32c8 upstream. Both vhci_get_user and vhci_release race with open_timeout work. They both contain cancel_delayed_work_sync, but do not test whether the work actually created hdev or not. Since the work can be in progress and _sync will wait for finishing it, we can have data->hdev allocated when cancel_delayed_work_sync returns. But the call sites do 'if (data->hdev)' *before* cancel_delayed_work_sync. As a result: * vhci_get_user allocates a second hdev and puts it into data->hdev. The former is leaked. * vhci_release does not release data->hdev properly as it thinks there is none. Fix both cases by moving the actual test *after* the call to cancel_delayed_work_sync. This can be hit by this program: #include <err.h> #include <fcntl.h> #include <stdio.h> #include <stdlib.h> #include <time.h> #include <unistd.h> #include <sys/stat.h> #include <sys/types.h> int main(int argc, char **argv) { int fd; srand(time(NULL)); while (1) { const int delta = (rand() % 200 - 100) * 100; fd = open("/dev/vhci", O_RDWR); if (fd < 0) err(1, "open"); usleep(1000000 + delta); close(fd); } return 0; } And the result is: BUG: KASAN: use-after-free in skb_queue_tail+0x13e/0x150 at addr ffff88006b0c1228 Read of size 8 by task kworker/u13:1/32068 ============================================================================= BUG kmalloc-192 (Tainted: G E ): kasan: bad access detected ----------------------------------------------------------------------------- Disabling lock debugging due to kernel taint INFO: Allocated in vhci_open+0x50/0x330 [hci_vhci] age=260 cpu=3 pid=32040 ... kmem_cache_alloc_trace+0x150/0x190 vhci_open+0x50/0x330 [hci_vhci] misc_open+0x35b/0x4e0 chrdev_open+0x23b/0x510 ... INFO: Freed in vhci_release+0xa4/0xd0 [hci_vhci] age=9 cpu=2 pid=32040 ... __slab_free+0x204/0x310 vhci_release+0xa4/0xd0 [hci_vhci] ... INFO: Slab 0xffffea0001ac3000 objects=16 used=13 fp=0xffff88006b0c1e00 flags=0x5fffff80004080 INFO: Object 0xffff88006b0c1200 @offset=4608 fp=0xffff88006b0c0600 Bytes b4 ffff88006b0c11f0: 09 df 00 00 01 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff88006b0c1200: 00 06 0c 6b 00 88 ff ff 00 00 00 00 00 00 00 00 ...k............ Object ffff88006b0c1210: 10 12 0c 6b 00 88 ff ff 10 12 0c 6b 00 88 ff ff ...k.......k.... Object ffff88006b0c1220: c0 46 c2 6b 00 88 ff ff c0 46 c2 6b 00 88 ff ff .F.k.....F.k.... Object ffff88006b0c1230: 01 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 ................ Object ffff88006b0c1240: 40 12 0c 6b 00 88 ff ff 40 12 0c 6b 00 88 ff ff @..k....@..k.... Object ffff88006b0c1250: 50 0d 6e a0 ff ff ff ff 00 02 00 00 00 00 ad de P.n............. Object ffff88006b0c1260: 00 00 00 00 00 00 00 00 ab 62 02 00 01 00 00 00 .........b...... Object ffff88006b0c1270: 90 b9 19 81 ff ff ff ff 38 12 0c 6b 00 88 ff ff ........8..k.... Object ffff88006b0c1280: 03 00 20 00 ff ff ff ff ff ff ff ff 00 00 00 00 .. ............. Object ffff88006b0c1290: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff88006b0c12a0: 00 00 00 00 00 00 00 00 00 80 cd 3d 00 88 ff ff ...........=.... Object ffff88006b0c12b0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 . .............. Redzone ffff88006b0c12c0: bb bb bb bb bb bb bb bb ........ Padding ffff88006b0c13f8: 00 00 00 00 00 00 00 00 ........ CPU: 3 PID: 32068 Comm: kworker/u13:1 Tainted: G B E 4.4.6-0-default #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.1-0-g4adadbd-20151112_172657-sheep25 04/01/2014 Workqueue: hci0 hci_cmd_work [bluetooth] 00000000ffffffff ffffffff81926cfa ffff88006be37c68 ffff88006bc27180 ffff88006b0c1200 ffff88006b0c1234 ffffffff81577993 ffffffff82489320 ffff88006bc24240 0000000000000046 ffff88006a100000 000000026e51eb80 Call Trace: ... [<ffffffff81ec8ebe>] ? skb_queue_tail+0x13e/0x150 [<ffffffffa06e027c>] ? vhci_send_frame+0xac/0x100 [hci_vhci] [<ffffffffa0c61268>] ? hci_send_frame+0x188/0x320 [bluetooth] [<ffffffffa0c61515>] ? hci_cmd_work+0x115/0x310 [bluetooth] [<ffffffff811a1375>] ? process_one_work+0x815/0x1340 [<ffffffff811a1f85>] ? worker_thread+0xe5/0x11f0 [<ffffffff811a1ea0>] ? process_one_work+0x1340/0x1340 [<ffffffff811b3c68>] ? kthread+0x1c8/0x230 ... Memory state around the buggy address: ffff88006b0c1100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88006b0c1180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >ffff88006b0c1200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff88006b0c1280: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff88006b0c1300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc Fixes: 23424c0d (Bluetooth: Add support creating virtual AMP controllers) Signed-off-by:
-
Itai Handler authored
commit 7ccca1d5 upstream. Fix possible out of bounds read, by adding missing comma. The code may read pass the end of the dsi_errors array when the most significant bit (bit #31) in the intr_stat register is set. This bug has been detected using CppCheck (static analysis tool). Signed-off-by:
Itai Handler <itai_handler@hotmail.com> Signed-off-by:
Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by:
-
Larry Finger authored
commit baa17022 upstream. The previous patch added an option to rtl8723be to manually select the antenna for those cases when only a single antenna is present, and the on-board EEPROM is incorrectly programmed. This patch implements the necessary changes in the Bluetooth coexistence driver. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> [ kamal: backport to 4.2-stable: files moved ] Signed-off-by:
-
Larry Finger authored
commit c18d8f50 upstream. A number of new laptops have been delivered with only a single antenna. In principle, this is OK; however, a problem arises when the on-board EEPROM is programmed to use the other antenna connection. The option of opening the computer and moving the connector is not always possible as it will void the warranty in some cases. In addition, this solution breaks the Windows driver when the box dual boots Linux and Windows. A fix involving a new module parameter has been developed. This commit adds the new parameter and implements the changes needed for the driver. Signed-off-by:
-
Dave Chinner authored
commit ad747e3b upstream. Commit 96f859d5 ("libxfs: pack the agfl header structure so XFS_AGFL_SIZE is correct") allowed the freelist to use the empty slot at the end of the freelist on 64 bit systems that was not being used due to sizeof() rounding up the structure size. This has caused versions of xfs_repair prior to 4.5.0 (which also has the fix) to report this as a corruption once the filesystem has been grown. Older kernels can also have problems (seen from a whacky container/vm management environment) mounting filesystems grown on a system with a newer kernel than the vm/container it is deployed on. To avoid this problem, change the initial free list indexes not to wrap across the end of the AGFL, hence avoiding the initialisation of agf_fllast to the last index in the AGFL. Signed-off-by:
Dave Chinner <dchinner@redhat.com> Reviewed-by:
Carlos Maiolino <cmaiolino@redhat.com> Signed-off-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
-
Eric Sandeen authored
commit d0a58e83 upstream. Today, a kernel which refuses to mount a filesystem read-write due to unknown ro-compat features can still transition to read-write via the remount path. The old kernel is most likely none the wiser, because it's unaware of the new feature, and isn't using it. However, writing to the filesystem may well corrupt metadata related to that new feature, and moving to a newer kernel which understand the feature will have problems. Right now the only ro-compat feature we have is the free inode btree, which showed up in v3.16. It would be good to push this back to all the active stable kernels, I think, so that if anyone is using newer mkfs (which enables the finobt feature) with older kernel releases, they'll be protected. Signed-off-by:
Eric Sandeen <sandeen@redhat.com> Reviewed-by:
Bill O'Donnell <billodo@redhat.com> Reviewed-by:
-
Joseph Salisbury authored
commit 7b9bc799 upstream. BugLink: http://bugs.launchpad.net/bugs/972604 Commit 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") added a pin configuration for the Compaq c700 laptop. However, the polarity of the led pin is reversed. It should be red for wifi off and blue for wifi on, but it is the opposite. This bug was reported in the following bug report: http://pad.lv/972604 Fixes: 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") Signed-off-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
-
- 08 Jun, 2016 2 commits
-
-
Imre Kaloz authored
commit 9800917c upstream. Some of the GPIO configs were wrong in the submitted DTS files, this patch fixes all affected boards. Signed-off-by:
Imre Kaloz <kaloz@openwrt.org> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Lyude authored
commit a16b7658 upstream. Since we need MST devices ready before we try to resume displays, calling this after intel_display_resume() can result in some issues with various laptop docks where the monitor won't turn back on after suspending the system. This order was originally changed in commit e7d6f7d7 ("drm/i915: resume MST after reading back hw state") In order to fix some unclaimed register errors, however the actual cause of those has since been fixed. Signed-off-by:
Lyude <cpaul@redhat.com> [danvet: Resolve conflicts with locking changes.] Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> [ kamal: backport to 4.2-stable: context ] Signed-off-by:
-
- 07 Jun, 2016 3 commits
-
-
Anilkumar Kolli authored
commit 9ddc486a upstream. It is observed that, we are disabling the packet log if we write same value to the pktlog_filter for the second time. Always enable pktlogs on non zero filter. Fixes: 90174455 ("ath10k: add support to configure pktlog filter") Signed-off-by:
Anilkumar Kolli <akolli@qti.qualcomm.com> Signed-off-by:
-
Lyude authored
commit 1f771755 upstream. After unplugging a DP MST display from the system, we have to go through and destroy all of the DRM connectors associated with it since none of them are valid anymore. Unfortunately, intel_dp_destroy_mst_connector() doesn't do a good enough job of ensuring that throughout the destruction process that no modesettings can be done with the connectors. As it is right now, intel_dp_destroy_mst_connector() works like this: * Take all modeset locks * Clear the configuration of the crtc on the connector, if there is one * Drop all modeset locks, this is required because of circular dependency issues that arise with trying to remove the connector from sysfs with modeset locks held * Unregister the connector * Take all modeset locks, again * Do the rest of the required cleaning for destroying the connector * Finally drop all modeset locks for good This only works sometimes. During the destruction process, it's very possible that a userspace application will attempt to do a modesetting using the connector. When we drop the modeset locks, an ioctl handler such as drm_mode_setcrtc has the oppurtunity to take all of the modeset locks from us. When this happens, one thing leads to another and eventually we end up committing a mode with the non-existent connector: [drm:intel_dp_link_training_clock_recovery [i915]] *ERROR* failed to enable link training [drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f [drm:intel_dp_start_link_train [i915]] *ERROR* failed to start channel equalization [drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f [drm:intel_mst_pre_enable_dp [i915]] *ERROR* failed to allocate vcpi And in some cases, such as with the T460s using an MST dock, this results in breaking modesetting and/or panicking the system. To work around this, we now unregister the connector at the very beginning of intel_dp_destroy_mst_connector(), grab all the modesetting locks, and then hold them until we finish the rest of the function. Signed-off-by:
Rob Clark <rclark@redhat.com> Reviewed-by:
-
Rajkumar Manoharan authored
commit 8a75fc54 upstream. commit 166de3f1 ("ath10k: remove supported chain mask") had revealed an issue on monitor mode. Configuring NSS upon monitor interface creation is causing target assert in all qca9888x and qca6174 firmware. Firmware assert issue can be reproduced by below sequence even after reverting commit 166de3f1 ("ath10k: remove supported chain mask"). ip link set wlan0 down iw wlan0 set type monitor iw phy0 set antenna 7 ip link set wlan0 up This issue is originally reported on qca9888 with 10.1 firmware. Fixes: 5572a95b ("ath10k: apply chainmask settings to vdev on creation") Reported-by:
Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by:
-
- 27 May, 2016 1 commit
-
-
Kamal Mostafa authored
Signed-off-by:
-
- 24 May, 2016 6 commits
-
-
Mikko Rapeli authored
[ Upstream commit 4a91cb61 ] glibc's net/if.h contains copies of definitions from linux/if.h and these conflict and cause build failures if both files are included by application source code. Changes in uapi headers, which fixed header file dependencies to include linux/if.h when it was needed, e.g. commit 1ffad83d, made the net/if.h and linux/if.h incompatibilities visible as build failures for userspace applications like iproute2 and xtables-addons. This patch fixes compile errors when glibc net/if.h is included before linux/if.h: ./linux/if.h:99:21: error: redeclaration of enumerator ‘IFF_NOARP’ ./linux/if.h:98:23: error: redeclaration of enumerator ‘IFF_RUNNING’ ./linux/if.h:97:26: error: redeclaration of enumerator ‘IFF_NOTRAILERS’ ./linux/if.h:96:27: error: redeclaration of enumerator ‘IFF_POINTOPOINT’ ./linux/if.h:95:24: error: redeclaration of enumerator ‘IFF_LOOPBACK’ ./linux/if.h:94:21: error: redeclaration of enumerator ‘IFF_DEBUG’ ./linux/if.h:93:25: error: redeclaration of enumerator ‘IFF_BROADCAST’ ./linux/if.h:92:19: error: redeclaration of enumerator ‘IFF_UP’ ./linux/if.h:252:8: error: redefinition of ‘struct ifconf’ ./linux/if.h:203:8: error: redefinition of ‘struct ifreq’ ./linux/if.h:169:8: error: redefinition of ‘struct ifmap’ ./linux/if.h:107:23: error: redeclaration of enumerator ‘IFF_DYNAMIC’ ./linux/if.h:106:25: error: redeclaration of enumerator ‘IFF_AUTOMEDIA’ ./linux/if.h:105:23: error: redeclaration of enumerator ‘IFF_PORTSEL’ ./linux/if.h:104:25: error: redeclaration of enumerator ‘IFF_MULTICAST’ ./linux/if.h:103:21: error: redeclaration of enumerator ‘IFF_SLAVE’ ./linux/if.h:102:22: error: redeclaration of enumerator ‘IFF_MASTER’ ./linux/if.h:101:24: error: redeclaration of enumerator ‘IFF_ALLMULTI’ ./linux/if.h:100:23: error: redeclaration of enumerator ‘IFF_PROMISC’ The cases where linux/if.h is included before net/if.h need a similar fix in the glibc side, or the order of include files can be changed userspace code as a workaround. This change was tested in x86 userspace on Debian unstable with scripts/headers_compile_test.sh: $ make headers_install && \ cd usr/include && ../../scripts/headers_compile_test.sh -l -k ... cc -Wall -c -nostdinc -I /usr/lib/gcc/i586-linux-gnu/5/include -I /usr/lib/gcc/i586-linux-gnu/5/include-fixed -I . -I /home/mcfrisk/src/linux-2.6/usr/headers_compile_test_include.2uX2zH -I /home/mcfrisk/src/linux-2.6/usr/headers_compile_test_include.2uX2zH/i586-linux-gnu -o /dev/null ./linux/if.h_libc_before_kernel.h PASSED libc before kernel test: ./linux/if.h Reported-by:
Jan Engelhardt <jengelh@inai.de> Reported-by:
Josh Boyer <jwboyer@fedoraproject.org> Reported-by:
Stephen Hemminger <shemming@brocade.com> Reported-by:
Waldemar Brodkorb <mail@waldemar-brodkorb.de> Cc: Gabriel Laskar <gabriel@lse.epita.fr> Signed-off-by:
Mikko Rapeli <mikko.rapeli@iki.fi> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Craig Gallek authored
[ Upstream commit d894ba18 ] With the SO_REUSEPORT socket option, it is possible to create sockets in the AF_INET and AF_INET6 domains which are bound to the same IPv4 address. This is only possible with SO_REUSEPORT and when not using IPV6_V6ONLY on the AF_INET6 sockets. Prior to the commits referenced below, an incoming IPv4 packet would always be routed to a socket of type AF_INET when this mixed-mode was used. After those changes, the same packet would be routed to the most recently bound socket (if this happened to be an AF_INET6 socket, it would have an IPv4 mapped IPv6 address). The change in behavior occurred because the recent SO_REUSEPORT optimizations short-circuit the socket scoring logic as soon as they find a match. They did not take into account the scoring logic that favors AF_INET sockets over AF_INET6 sockets in the event of a tie. To fix this problem, this patch changes the insertion order of AF_INET and AF_INET6 addresses in the TCP and UDP socket lists when the sockets have SO_REUSEPORT set. AF_INET sockets will be inserted at the head of the list and AF_INET6 sockets with SO_REUSEPORT set will always be inserted at the tail of the list. This will force AF_INET sockets to always be considered first. Fixes: e32ea7e7 ("soreuseport: fast reuseport UDP socket selection") Fixes: 125e80b88687 ("soreuseport: fast reuseport TCP socket selection") Reported-by:
Maciej Żenczykowski <maze@google.com> Signed-off-by:
Craig Gallek <kraig@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Bjørn Mork authored
[ Upstream commit c5b5343c ] We now have a positive report of another Huawei device needing this quirk: The ME906s-158 (12d1:15c1). This is an m.2 form factor modem with no obvious relationship to the E3372 (12d1:157d) we already have a quirk entry for. This is reason enough to believe the quirk might be necessary for any number of current and future Huawei devices. Applying the quirk to all Huawei devices, since it is crucial to any device affected by the firmware bug, while the impact on non-affected devices is negligible. The quirk can if necessary be disabled per-device by writing N to /sys/class/net/<iface>/cdc_ncm/ndp_to_end Reported-by:
Andreas Fett <andreas.fett@secunet.com> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit 79e48650 ] Stack object "dte_facilities" is allocated in x25_rx_call_request(), which is supposed to be initialized in x25_negotiate_facilities. However, 5 fields (8 bytes in total) are not initialized. This object is then copied to userland via copy_to_user, thus infoleak occurs. Signed-off-by:
Kangjie Lu <kjlu@gatech.edu> Signed-off-by:
-
Nikolay Aleksandrov authored
[ Upstream commit 31ca0458 ] get_bridge_ifindices() is used from the old "deviceless" bridge ioctl calls which aren't called with rtnl held. The comment above says that it is called with rtnl but that is not really the case. Here's a sample output from a test ASSERT_RTNL() which I put in get_bridge_ifindices and executed "brctl show": [ 957.422726] RTNL: assertion failed at net/bridge//br_ioctl.c (30) [ 957.422925] CPU: 0 PID: 1862 Comm: brctl Tainted: G W O 4.6.0-rc4+ #157 [ 957.423009] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.8.1-20150318_183358- 04/01/2014 [ 957.423009] 0000000000000000 ffff880058adfdf0 ffffffff8138dec5 0000000000000400 [ 957.423009] ffffffff81ce8380 ffff880058adfe58 ffffffffa05ead32 0000000000000001 [ 957.423009] 00007ffec1a444b0 0000000000000400 ffff880053c19130 0000000000008940 [ 957.423009] Call Trace: [ 957.423009] [<ffffffff8138dec5>] dump_stack+0x85/0xc0 [ 957.423009] [<ffffffffa05ead32>] br_ioctl_deviceless_stub+0x212/0x2e0 [bridge] [ 957.423009] [<ffffffff81515beb>] sock_ioctl+0x22b/0x290 [ 957.423009] [<ffffffff8126ba75>] do_vfs_ioctl+0x95/0x700 [ 957.423009] [<ffffffff8126c159>] SyS_ioctl+0x79/0x90 [ 957.423009] [<ffffffff8163a4c0>] entry_SYSCALL_64_fastpath+0x23/0xc1 Since it only reads bridge ifindices, we can use rcu to safely walk the net device list. Also remove the wrong rtnl comment above. Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
Ian Campbell authored
[ Upstream commit dedc58e0 ] The peer may be expecting a reply having sent a request and then done a shutdown(SHUT_WR), so tearing down the whole socket at this point seems wrong and breaks for me with a client which does a SHUT_WR. Looking at other socket family's stream_recvmsg callbacks doing a shutdown here does not seem to be the norm and removing it does not seem to have had any adverse effects that I can see. I'm using Stefan's RFC virtio transport patches, I'm unsure of the impact on the vmci transport. Signed-off-by:
Ian Campbell <ian.campbell@docker.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Stefan Hajnoczi <stefanha@redhat.com> Cc: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com> Cc: Andy King <acking@vmware.com> Cc: Dmitry Torokhov <dtor@vmware.com> Cc: Jorgen Hansen <jhansen@vmware.com> Cc: Adit Ranadive <aditr@vmware.com> Cc: netdev@vger.kernel.org Signed-off-by:
-
