kzm9g supplies 3.3V to its SDHI0 and SDHI2 interfaces. Specifying 2.8V
prevents some (e.g. certain SDIO) cards from working. This patch fixes the
voltage and removes redundant OCR masks from platform data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Correct the name of smsc devices used for regulator registration
allowing the regulators to be found and used.

This eliminates the need for CONFIG_REGULATOR_DUMMY
when CONFIG_REGULATOR is set.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: add gic_iid macro for ICCIAR / interrupt ID
enabled to use gic_iid macro.
This patch exchange current GIC interrupt setting
from gic_spi() to gic_iid()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[ horms+renesas@verge.net.au: Split irq.h portion into a separate patch ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Remove .init_late and .restart from DT_MACHINE_START
for kzm9g reference as these are not necessary to
bring the board up which is the main aim of kzm9g reference.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Remove warning about SMP not working with the
clock initialisation used for kzm9g reference.

This is resolved by not selecting CONFIG_PREEMPT.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Reference kernel configurations for armadillo800eva and kzm9g boards do not
have to depend on their respective "legacy" configurations, doing device
instantiation in .c, they can be configured and built independently.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[horms+renesas@verge.net.au: created separate patch for kzm9g portion]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add SDHI0 and SDHI2 interfaces to kzm9g-reference. With no pinctrl DT
support we cannot use GPIO card-detection and regulator switching.
Also update the MMCIF DT node to use all 8 data lines and avoid
redundant information in DT.

Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
[ horms+renesas@verge.net.au: Updated for pinmux changes by Laurent Pinchart ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

GPIOs can be provided by the pinctrl subsystem, which can be initialised
by DT. Therefore DT has to be parsed before requesting GPIOs. Also non-DT
pinmux has to be configured early.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Provide alternate board code for the kzm9g to demonstrate
how DT may be used given the current state of driver
device tree support. This is intended to act as a reference
for mach-shmobile developers.

Some notes:

* Brings up the GIC interrupt handler using device tree
* Brings up the following device using device tree:
  - MMCIF (MMC)
* Does not bring up the INTC interrupt controller at all,
  thus external devices may not be used. In particular,
  the SMSC ethernet device may not be used and thus
  NFS root may not be used.
* Uses existing C code and not device tree to initialise the following,
  which are needed for a working board:
  - SCIF (Serial)
  - CMT (Clock)
  - PFC (GPIO)

To use this alternate board code instead of the normal board code,
CONFIG_MACH_KZM9G_REFERENCE should be selected in the kernel config.
And the sh73a0-kzm9g-reference.dtb flattened device tree blob should be used.

Includes fix by Thierry Reding to no longer use gic_handle_irq()

Includes fixes by Guennadi Liakhovetski for recent pinmux changes.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Provide alternate board code for the marzen to demonstrate
how DT may be used given the current state of driver
device tree support. This is intended to act as a reference
for mach-shmobile developers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Patch eac036ef9e "ARM: shmobile: streamline mackerel SD and MMC devices"
made the use of the sh_mmcif_device variable for mackarel optional,
but the definition is always provided, causing a build warning.

arch/arm/mach-shmobile/board-mackerel.c:1120:31: warning: 'sh_mmcif_device'
	defined but not used [-Wunused-variable]

Marking the variable as __maybe_unused will do the right thing here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch fixes the following issues with SD and MMC interfaces on mackerel:
1. replace custom card-detection functions with standard GPIO CD API
2. resources don't have to be numbered
3. add SDHI interrupt names
4. remove OCR masks, where regulators are used
5. only specify SDHI CD interrupts on interfaces where a CD pin is present -
   SDHI0
6. don't instantiate an MMCIF device and initialise MMCIF pins if SDHI1 is
   selected
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

When regulators are used with MMC devices, explicitly provided OCR masks
are ignored, they can be removed from platform data. Also switch SDHI0
from fixed regulator with hard-wired GPIO levels to a proper GPIO regulator
instance to enable dynamic voltage switching.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Switch SDHI0 and SDHI1 SD-card interfaces on armadillo800eva to using GPIO
card detection, which provides maximum power saving and automatically
selects IRQ or polling mode, depending on the CD GPIO capability.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
[Rename device from to rcarfb to rcar-du]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[Manual conflict resolution]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The function is not documented in the r8a7779 datasheet. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinconf API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Those GPIOs have been deprecated by the pinctrl API. They are unused and
unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

All r8a7779 platforms now use the pinctrl API to control the INTC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

All r8a7779 platforms now use the pinctrl API to control the LBSC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

All r8a7779 platforms now use the pinctrl API to control the USB pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

All r8a7779 platforms now use the pinctrl API to control the HSPI pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>