Pull MIPS fixes from Ralf Baechle:
 "This is dominated by a large number of changes necessary for the MIPS
  BPF code.  code.  Aside of that there are

   - a fix for the MSC system controller support code.
   - a Turbochannel fix.
   - a recordmcount fix that's MIPS-specific.
   - barrier fixes to smp-cps / pm-cps after unrelated changes elsewhere
     in the kernel.
   - revert support for MSA registers in the signal frames.  The
     reverted patch did modify the signal stack frame which of course is
     inacceptable.
   - fix math-emu build breakage with older compilers.
   - some related cleanup.
   - fix Lasat build error if CONFIG_CRC32 isn't set to y by the user"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (27 commits)
  MIPS: Lasat: Fix build error if CRC32 is not enabled.
  TC: Handle device_register() errors.
  MIPS: MSC: Prevent out-of-bounds writes to MIPS SC ioremap'd region
  MIPS: bpf: Fix stack space allocation for BPF memwords on MIPS64
  MIPS: BPF: Use 32 or 64-bit load instruction to load an address to register
  MIPS: bpf: Fix PKT_TYPE case for big-endian cores
  MIPS: BPF: Prevent kernel fall over for >=32bit shifts
  MIPS: bpf: Drop update_on_xread and always initialize the X register
  MIPS: bpf: Fix is_range() semantics
  MIPS: bpf: Use pr_debug instead of pr_warn for unhandled opcodes
  MIPS: bpf: Fix return values for VLAN_TAG_PRESENT case
  MIPS: bpf: Use correct mask for VLAN_TAG case
  MIPS: bpf: Fix branch conditional for BPF_J{GT/GE} cases
  MIPS: bpf: Add SEEN_SKB to flags when looking for the PKT_TYPE
  MIPS: bpf: Use 'andi' instead of 'and' for the VLAN cases
  MIPS: bpf: Return error code if the offset is a negative number
  MIPS: bpf: Use the LO register to get division's quotient
  MIPS: mm: uasm: Fix lh micro-assembler instruction
  MIPS: uasm: Add SLT uasm instruction
  MIPS: uasm: Add s3s1s2 instruction builder
  ...

Pull ARC fixes from Vineet Gupta:
 "Some SMP changes, a ptrace request for NPTL debugging, bunch of build
  breakages/warnings"

* tag 'arc-fixes-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: [SMP] Enable icache coherency
  ARC: [SMP] Fix IPI IRQ registration
  ARC: Implement ptrace(PTRACE_GET_THREAD_AREA)
  ARC: optimize kernel bss clearing in early boot code
  ARC: Fix build breakage for !CONFIG_ARC_DW2_UNWIND
  ARC: fix build warning in devtree
  ARC: remove checks for CONFIG_ARC_MMU_V4

Pull compress bugfix from Greg KH:
 "Here is another lz4 bugfix for 3.16-rc3 that resolves a reported issue
  with that compression algorithm"

* tag 'compress-3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  lz4: fix another possible overrun

Merge tag 'stable/for-linus-3.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb

Pull swiotlb bugfix from Konrad Rzeszutek Wilk:
 "One bug-fix that had been in tree for quite some time.  We had assumed
  that the physical address zero was invalid and would fail it.  But
  that is not true and on some architectures it is not reserved and
  valid.  This fixes it"

* tag 'stable/for-linus-3.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
  swiotlb: don't assume PA 0 is invalid

Pull sound fixes from Takashi Iwai:
 "Here includes a few patchset for fixing mostly HD-audio issues in
  addition to a patch assuring the compress API bytes alignment and a
  fix for the die-hard existing race condition at USB-audio
  disconnection.  The volume looks big in Realtek HD-audio code, but
  it's just a translation of the fixup tables, and the actual changes
  are rather trivial"

* tag 'sound-3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - restore BCLK M/N values when resuming HSW/BDW display controller
  ALSA: usb-audio: Fix races at disconnection and PCM closing
  ALSA: hda - Adjust speaker HPF and add LED support for HP Spectre 13
  ALSA: hda - Make the pin quirk tables use the SND_HDA_PIN_QUIRK macro
  ALSA: hda - Make a SND_HDA_PIN_QUIRK macro
  ALSA: hda - Add pin quirk for Dell XPS 15
  ALSA: hda - hdmi: call overridden init on resume
  ALSA: hda - Fix usage of "model" module parameter
  ALSA: compress: fix the struct alignment to 4 bytes

Pull MFD fixes from Lee Jones:
 "Couple of simple fixes due for the v3.16 -rcs"

* tag 'mfd-fixes-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
  mfd: ab8500: Fix dt irq mapping
  mfd: davinci: Voicecodec needs regmap_mmio
  mfd: STw481x: Allow modular build
  mfd: UCB1x00: Enable modular build

Pull drm fixes from Dave Airlie:
 "Exynos, i915 and msm fixes and one core fix.

  exynos:
     hdmi power off and mixer issues

  msm:
     iommu, build fixes,

  i915:
     regression races and warning fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
  drm/i915: vlv_prepare_pll is only needed in case of non DSI interfaces
  drm: fix NULL pointer access by wrong ioctl
  drm/exynos: enable vsync interrupt while waiting for vblank
  drm/exynos: soft reset mixer before reconfigure after power-on
  drm/exynos: allow multiple layer updates per vsync for mixer
  drm/i915: Hold the table lock whilst walking the file's idr and counting the objects in debugfs
  drm/i915: BDW: Adding Reserved PCI IDs.
  drm/i915: Only mark the ctx as initialised after a SET_CONTEXT operation
  drm/exynos: stop mixer before gating clocks during poweroff
  drm/exynos: set power state variable after enabling clocks and power
  drm/exynos: disable unused windows on apply
  drm/exynos: Fix de-registration ordering
  drm/exynos: change zero to NULL for sparse
  drm/exynos: dpi: Fix NULL pointer dereference with legacy bindings
  drm/exynos: hdmi: fix power order issue
  drm/i915: default to having backlight if VBT not available
  drm/i915: cache hw power well enabled state
  drm/msm: fix IOMMU cleanup for -EPROBE_DEFER
  drm/msm: use PAGE_ALIGNED instead of IS_ALIGNED(PAGE_SIZE)
  drm/msm/hdmi: set hdp clock rate before prepare_enable
  ...

There is one other possible overrun in the lz4 code as implemented by
Linux at this point in time (which differs from the upstream lz4
codebase, but will get synced at in a future kernel release.)  As
pointed out by Don, we also need to check the overflow in the data
itself.

While we are at it, replace the odd error return value with just a
"simple" -1 value as the return value is never used for anything other
than a basic "did this work or not" check.
Reported-by: "Don A. Bailey" <donb@securitymouse.com>
Reported-by: Willy Tarreau <w@1wt.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixes for 3.16-rc2; regressions, races, and warns; Broadwell PCI IDs.

* tag 'drm-intel-fixes-2014-06-26' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: vlv_prepare_pll is only needed in case of non DSI interfaces
  drm/i915: Hold the table lock whilst walking the file's idr and counting the objects in debugfs
  drm/i915: BDW: Adding Reserved PCI IDs.
  drm/i915: Only mark the ctx as initialised after a SET_CONTEXT operation
  drm/i915: default to having backlight if VBT not available
  drm/i915: cache hw power well enabled state

Pull block fixes from Jens Axboe:
 "A small collection of fixes/changes for the current series.  This
  contains:

   - Removal of dead code from Gu Zheng.

   - Revert of two bad fixes that went in earlier in this round, marking
     things as __init that were not purely used from init.

   - A fix for blk_mq_start_hw_queue() using the __blk_mq_run_hw_queue(),
     which could place us wrongly.  Make it use the non __ variant,
     which handles cases where we are called from the wrong CPU set.
     From me.

   - A fix for drbd, which allocates discard requests without room for
     the SCSI payload.  From Lars Ellenberg.

   - A fix for user-after-free in the blkcg code from Tejun.

   - Addition of limiting gaps in SG lists, if the hardware needs it.
     This is the last pre-req patch for blk-mq to enable the full NVMe
     conversion.  Could wait until 3.17, but it's simple enough so would
     be nice to have everything we need for the NVMe port in the 3.17
     release.  From me"

* 'for-linus' of git://git.kernel.dk/linux-block:
  drbd: fix NULL pointer deref in blk_add_request_payload
  blk-mq: blk_mq_start_hw_queue() should use blk_mq_run_hw_queue()
  block: add support for limiting gaps in SG lists
  bio: remove unused macro bip_vec_idx()
  Revert "block: add __init to elv_register"
  Revert "block: add __init to blkcg_policy_register"
  blkcg: fix use-after-free in __blkg_release_rcu() by making blkcg_gq refcnt an atomic_t
  floppy: format block0 read error message properly

blkdev_read_iter() wants to cap the iov_iter by the amount of data
remaining to the end of device.  That's what iov_iter_truncate() is for
(trim iter->count if it's above the given limit).  So far, so good, but
the argument of iov_iter_truncate() is size_t, so on 32bit boxen (in
case of a large device) we end up with that upper limit truncated down
to 32 bits *before* comparing it with iter->count.

Easily fixed by making iov_iter_truncate() take 64bit argument - it does
the right thing after such change (we only reach the assignment in there
when the current value of iter->count is greater than the limit, i.e.
for anything that would get truncated we don't reach the assignment at
all) and that argument is not the new value of iter->count - it's an
upper limit for such.

The overhead of passing u64 is not an issue - the thing is inlined, so
callers passing size_t won't pay any penalty.
Reported-and-tested-by: Theodore Tso <tytso@mit.edu>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

For Intel Haswell/Broadwell display HD-A controller, the 24MHz HD-A link BCLK
is converted from Core Display Clock (CDCLK): BCLK = CDCLK * M / N
And there are two registers EM4 and EM5 to program M, N value respectively.
The EM4/EM5 values will be lost and when the display power well is disabled.

BIOS programs CDCLK selected by OEM and EM4/EM5, but BIOS has no idea about
display power well on/off at runtime. So the M/N can be wrong if non-default
CDCLK is used when the audio controller resumes, which results in an invalid
BCLK and abnormal audio playback rate. So this patch saves and restores valid
M/N values on controller suspend/resume.

And 'struct hda_intel' is defined to contain standard HD-A 'struct azx' and
Intel specific fields, as Takashi suggested.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Kconfig doesn't select CRC32 so it's possible to build a Lasat kernel
without CONFIG_CRC32 resulting in a build error:

  LD      vmlinux
arch/mips/built-in.o: In function `lasat_init_board_info':
(.text+0x22c): undefined reference to `crc32_le'
arch/mips/built-in.o: In function `lasat_write_eeprom_info':
(.text+0x7fc): undefined reference to `crc32_le'
make: *** [vmlinux] Error 1
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The AD8500 defines itself as interrupt-controller in DT,
but it doesn't assign DT node to IRQ domain when creates it.
As result, of_irq_xx() helpers don't work because they can't
find necessary IRQ domain.

Hence, fix it by assigning AD8500 core device DT node to IRQ
domain when it's created.

This patch fixes STE u8500 Snowball boot failure reported by Kevin Hilman
https://lkml.org/lkml/2014/5/27/624Reported-and-tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Without REGMAP_MMIO, building that driver results in a link error:

drivers/built-in.o: In function `davinci_vc_probe':
:(.init.text+0x3c1c): undefined reference to `devm_regmap_init_mmio_clk'

This adds a Kconfig 'select' statement as the usual way to ensure
that REGMAP_MMIO is enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This driver depends on I2C, which may be a loadable module.
While you'd probably want both to be built-in in practice,
allowing a modular build avoids possible randconfig link
errors.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The UCB1200 / UCB1300 driver uses the MCP_SA11X0 driver, which
can be a loadable module, but this results in a link error
when UCB1200 itself is built-in:

drivers/built-in.o: In function `ucb1x00_io_set_dir':
:(.text+0x4a364): undefined reference to `mcp_reg_write'
drivers/built-in.o: In function `ucb1x00_io_write':
:(.text+0x4a3dc): undefined reference to `mcp_reg_write'
drivers/built-in.o: In function `ucb1x00_io_read':
:(.text+0x4a400): undefined reference to `mcp_reg_read'
drivers/built-in.o: In function `ucb1x00_adc_enable':
:(.text+0x4a460): undefined reference to `mcp_enable'
...

This can easily be resolved by making CONFIG_MCP_UCB1200 itself
a tristate option, since that causes Kconfig to track the
dependency correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Make the TURBOchannel driver bail out if the call to device_register()
failed.
Signed-off-by: Levente Kurusa <levex@linux.com>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6673/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Previously, the lower limit for the MIPS SC initialization loop was
set incorrectly allowing one extra loop leading to writes
beyond the MSC ioremap'd space. More precisely, the value of the 'imp'
in the last loop increased beyond the msc_irqmap_t boundaries and
as a result of which, the 'n' variable was loaded with an incorrect
value. This value was used later on to calculate the offset in the
MSC01_IC_SUP which led to random crashes like the following one:

CPU 0 Unable to handle kernel paging request at virtual address e75c0200,
epc == 8058dba4, ra == 8058db90
[...]
Call Trace:
[<8058dba4>] init_msc_irqs+0x104/0x154
[<8058b5bc>] arch_init_irq+0xd8/0x154
[<805897b0>] start_kernel+0x220/0x36c

Kernel panic - not syncing: Attempted to kill the idle task!

This patch fixes the problem
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7118/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

When allocating stack space for BPF memwords we need to use the
appropriate 32 or 64-bit instruction to avoid losing the top 32 bits
of the stack pointer.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7135/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

When loading a pointer to register we need to use the appropriate
32 or 64bit instruction to preserve the pointers' top 32bits.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7180/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The skb->pkt_type field is defined as follows:

u8 pkt_type:3,
   fclone:2,
   ipvs_property:1,
   peeked:1,
   nf_trace:1

resulting to the following layout in big-endian systems

[pkt_type][fclone][ipvs_propery][peeked][nf_trace]
^                                                ^
|                                                |
LSB                                             MSB

As a result, the existing code did not work because it was trying to
match pkt_type == 7 whereas in reality it is 7<<5 on big-endian
systems.

This has been fixed in the interpreter in
0dcceabb
"net: filter: fix SKF_AD_PKTTYPE extension on big-endian"

The fix is to look for 7<<5 on big-endian systems for the pkt_type
field, and shift by 5 so the packet type will be at the lower 3 bits
of the A register.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7132/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Remove BUG_ON() if the shift immediate is >=32 to avoid kernel crashes
due to malicious user input. If the shift immediate is >= 32,
we simply load the destination register with 0 since only
32-bit instructions are used by JIT so this will do the
correct thing even on MIPS64.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7179/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Previously, update_on_xread() only set the reset flag if SEEN_X hasn't
been set already. However, SEEN_X is used to indicate that X is used
as destination or source register so there are some cases where X
is only used as source register and we really need to make sure that it
has been initialized in time. As a result of which, drop this function and
always set X to zero if it's used in any of the opcodes.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7133/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

is_range() was meant to check whether the number is within
the s16 range or not. However the return values and consumers expected
the exact opposite. We fix that by inverting the logic in the function
to return 'true' for < s16 and 'false' for > s16.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reported-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7131/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

We should prevent spamming the logs during normal execution of bpf-jit.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Suggested-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7129/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

If VLAN_TAG_PRESENT is not zero, then return 1 as expected by
classic BPF. Otherwise return 0.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7128/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Using VLAN_VID_MASK is not correct to get the vlan tag. Use
~VLAN_PRESENT_MASK instead and make sure it's u16 so the top 16-bits
will be removed. This will ensure that the emit_andi() code will not
treat this as a big 32-bit unsigned value.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7127/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The sltiu and sltu instructions will set the scratch register
to 1 if A <= X|K so fix the emitted branch conditional to check
for scratch != zero rather than scratch >= zero which would complicate
the resuling branch logic given that MIPS does not have a BGT or BGET
instructions to compare general purpose registers directly.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7126/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The SKF_AD_PKTTYPE uses the skb pointer so make sure it's in the
flags so it will be initialized in time.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7125/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The VLAN_VID_MASK and VLAN_TAG_PRESENT are immediates, so using
'and' which expects 3 registers will produce wrong results. Fix
this by using the 'andi' instruction.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7124/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Previously, the negative offset was not checked leading to failures
due to trying to load data beyond the skb struct boundaries. Until we
have proper asm helpers in place, it's best if we return ENOSUPP if K
is negative when trying to JIT the filter or 0 during runtime if we
do an indirect load where the value of X is unknown during build time.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7123/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Reading from the HI register to get the division result is wrong.
The quotient is placed in the LO register.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7122/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Commit d6b3314b "MIPS: uasm: Add lh uam
instruction" added the 'lh' micro-assembler instruction but it used the
'lw' opcode for it. Fix it by using the correct 'lh' opcode.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7121/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It will be used later on by bpf-jit
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/7120/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It will be used later on by the SLT instruction.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7119/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

On MIPS calls to _mcount in modules generate 2 instructions to load
the _mcount address (and therefore 2 relocations). The mcount_loc
table should only reference the first of these, so the second is
filtered out by checking the relocation offset and ignoring ones that
immediately follow the previous one seen.

However if a module has an _mcount call at offset 0, the second
relocation would not be filtered out due to old_r_offset == 0
being taken to mean that the current relocation is the first one
seen, and both would end up in the mcount_loc table.

This results in ftrace_make_nop() patching both (adjacent)
instructions to branches over the _mcount call sequence like so:

  0xffffffffc08a8000:  04 00 00 10     b       0xffffffffc08a8014
  0xffffffffc08a8004:  04 00 00 10     b       0xffffffffc08a8018
  0xffffffffc08a8008:  2d 08 e0 03     move    at,ra
  ...

The second branch is in the delay slot of the first, which is
defined to be unpredictable - on the platform on which this bug was
encountered, it triggers a reserved instruction exception.

Fix by initializing old_r_offset to ~0 and using that instead of 0
to determine whether the current relocation is the first seen.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7098/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

  mips: allmodconfig fails in 3.16-rc1 with lots of undefined symbols.

  arch/mips/net/bpf_jit.c: In function 'is_load_to_a':
  arch/mips/net/bpf_jit.c:559:7: error: 'BPF_S_LD_W_LEN' undeclared (first use in this function)
  arch/mips/net/bpf_jit.c:559:7: note: each undeclared identifier is reported only once for each function it appears in
  arch/mips/net/bpf_jit.c:560:7: error: 'BPF_S_LD_W_ABS' undeclared (first use in this function)
  [...]

The reason behind this is that 34805931 ("net: filter: get rid of
BPF_S_* enum") was routed via net-next tree, that takes all BPF-related
changes, at a time where MIPS BPF JIT was not part of net-next, while
c6610de3 ("MIPS: net: Add BPF JIT") was routed via mips arch tree
and went into mainline within the same merge window. Thus, fix it up by
converting BPF_S_* in a similar fashion as in 34805931 for MIPS.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org>
Cc: Linux MIPS Mailing List <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7099/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This reverts commit eec43a22 "MIPS: Save/restore MSA context around
signals" and the MSA parts of ca750649 "MIPS: kernel: signal:
Prevent save/restore FPU context in user memory" (the restore path of
which appears incorrect anyway...).

The reverted patch took care not to break compatibility with userland
users of struct sigcontext, but inadvertantly changed the offset of the
uc_sigmask field of struct ucontext. Thus Linux v3.15 breaks the
userland ABI. The MSA context will need to be saved via some other
opt-in mechanism, but for now revert the change to reduce the fallout.

This will have minimal impact upon use of MSA since the only supported
CPU which includes it (the P5600) is 32-bit and therefore requires that
the experimental CONFIG_MIPS_O32_FP64_SUPPORT Kconfig option be selected
before the kernel will set FR=1 for a task, a requirement for MSA use.
Thus the users of MSA are limited to known small groups of people & this
patch won't be breaking any previously working MSA-using userland
outside of experimental settings.

[ralf@linux-mips.org: Fixed rejects.]

Cc: stable@vger.kernel.org
Reported-by: Joseph S. Myers <joseph@codesourcery.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7107/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The fix in the preceeding commit did do exactly the same thing in two
places showing some code cleanup was due.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>