Patch cef401de (net: fix possible wrong checksum
generation) fixed wrong checksum calculation but it broke TSO by
defining new GSO type but not a netdev feature for that type.
net_gso_ok() would not allow hardware checksum/segmentation
offload of such packets without the feature.

Following patch fixes TSO and wrong checksum. This patch uses
same logic that Eric Dumazet used. Patch introduces new flag
SKBTX_SHARED_FRAG if at least one frag can be modified by
the user. but SKBTX_SHARED_FRAG flag is kept in skb shared
info tx_flags rather than gso_type.

tx_flags is better compared to gso_type since we can have skb with
shared frag without gso packet. It does not link SHARED_FRAG to
GSO, So there is no need to define netdev feature for this.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrey Vagin says:

====================
If a TCP socket will get live-migrated from one box to another the
timestamps (which are typically ON) will get screwed up -- the new
kernel will generate TS values that has nothing to do with what they
were on dump. The solution is to yet again fix the kernel and put a
"timestamp offset" on a socket.

A socket offset is added in places where externally visible tcp
timestamp option is parsed/initialized.

Connections in the SYN_RECV state are not supported, global
tcp_time_stamp is used for them, because repair mode doesn't support
this state. In a future it can be implemented by the similar way as for
TIME_WAIT sockets.

For time-wait sockets offset is inhereted by a proper tcp_sock.

A per-socket offset can be set only for sockets in repair mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A socket timestamp is a sum of the global tcp_time_stamp and
a per-socket offset.

A socket offset is added in places where externally visible
tcp timestamp option is parsed/initialized.

Connections in the SYN_RECV state are not supported, global
tcp_time_stamp is used for them, because repair mode doesn't support
this state. In a future it can be implemented by the similar way
as for TIME_WAIT sockets.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

A timestamp can be set, only if a socket is in the repair mode.

This patch adds a new socket option TCP_TIMESTAMP, which allows to
get and set current tcp times stamp.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This functionality is used for restoring tcp sockets. A tcp timestamp
depends on how long a system has been running, so it's differ for each
host. The solution is to set a per-socket offset.

A per-socket offset for a TIME_WAIT socket is inherited from a proper
tcp socket.

tcp_request_sock doesn't have a timestamp offset, because the repair
mode for them are not implemented.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Paul Gortmaker says:

====================
Eric noticed that the handling of local u64 ethtool counters for
this driver commonly found on Freescale ppc-32 boards was racy.

However, before converting them over to atomic64_t, I noticed
that an internal struct was being used to determine the offsets
for exporting this data into the ethtool buffer, and in doing
so, it assumed that the counters would always be u64.  Rather
than keep this implicit assumption, a simple code cleanup gets
rid of the struct completely, and leaves less conversion sites.

The alternative solution would have been to take advantage of
the fact that the counters are all relating to error conditions,
and hence make them internally u32.  In doing so, we'd be assuming
that U32_MAX of any particular error condition is highly unlikely.
This might have made sense if any increments were in a hot path.

Tested with "ethtool -S eth0" on sbc8548 board.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Dan Carpenter contacted me with some notes regarding some smatch warnings in the
netpoll code, some of which I introduced with my recent netpoll locking fixes,
some which were there prior.   Specifically they were:

net-next/net/core/netpoll.c:243 netpoll_poll_dev() warn: inconsistent
  returns mutex:&ni->dev_lock: locked (213,217) unlocked (210,243)
net-next/net/core/netpoll.c:706 netpoll_neigh_reply() warn: potential
  pointer math issue ('skb_transport_header(send_skb)' is a 128 bit pointer)

This patch corrects the locking imbalance (the first error), and adds some
parenthesis to correct the second error.  Tested by myself. Applies to net-next
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

I get the following build error on next-20130213 due to the following
commit:

commit f05de73b ("skbuff: create
skb_panic() function and its wrappers").

It adds an argument called panic to a function that uses the BUG() macro
which tries to call panic, but the argument masks the panic() function
declaration, resulting in the following error (gcc 4.2.4):

net/core/skbuff.c In function 'skb_panic':
net/core/skbuff.c +126 : error: called object 'panic' is not a function

This is fixed by renaming the argument to msg.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Jean Sacren <sakiwit@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

While looking at some asm dump for an unrelated change, Eric
noticed in the following stats count increment code:

    50b8:       81 3c 01 f8     lwz     r9,504(r28)
    50bc:       81 5c 01 fc     lwz     r10,508(r28)
    50c0:       31 4a 00 01     addic   r10,r10,1
    50c4:       7d 29 01 94     addze   r9,r9
    50c8:       91 3c 01 f8     stw     r9,504(r28)
    50cc:       91 5c 01 fc     stw     r10,508(r28)

that a 64 bit counter was used on ppc-32 without sync
and hence the "ethtool -S" output was racy.

Here we convert all the values to use atomic64_t so that
the output will always be consistent.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

The gfar_stats struct is only used in copying out data
via ethtool.  It is declared as the extra stats, followed
by the rmon stats.  However, the rmon stats are never
actually ever used in the driver; instead the rmon data
is a u32 register read that is cast directly into the
ethtool buf.

It seems the only reason rmon is in the struct at all is
to give the offset(s) at which it should be exported into
the ethtool buffer.  But note gfar_stats doesn't contain
a gfar_extra_stats as a substruct -- instead it contains
a u64 array of equal element count.  This implicitly means
we have two independent declarations of what gfar_extra_stats
really is.  Rather than have this duality, we already have
defines which give us the offset directly, and hence do not
need the struct at all.

Further, since we know the extra_stats is unconditionally
always present, we can write it out to the ethtool buf
1st, and then optionally write out the rmon data.  There
is no need for two independent loops, both of which are
simply copying out the extra_stats to buf offset zero.

This also helps pave the way towards allowing the extra
stats fields to be converted to atomic64_t values, without
having their types directly influencing the ethtool stats
export code (gfar_fill_stats) that expects to deal with u64.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>

Current act_police uses rate table computed by the "tc" userspace
program, which has the following issue:

The rate table has 256 entries to map packet lengths to token (time
units).  With TSO sized packets, the 256 entry granularity leads to
loss/gain of rate, making the token bucket inaccurate.

Thus, instead of relying on rate table, this patch explicitly computes
the time and accounts for packet transmission times with nanosecond
granularity.

This is a followup to 56b765b7
("htb: improved accuracy at high rates").
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's not used anywhere else, so move it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current TBF uses rate table computed by the "tc" userspace program,
which has the following issue:

The rate table has 256 entries to map packet lengths to
token (time units).  With TSO sized packets, the 256 entry granularity
leads to loss/gain of rate, making the token bucket inaccurate.

Thus, instead of relying on rate table, this patch explicitly computes
the time and accounts for packet transmission times with nanosecond
granularity.

This is a followup to 56b765b7
("htb: improved accuracy at high rates").
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tbf will need to schedule watchdog in ns. No need to convert it twice.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As it is going to be used in tbf as well, push these to generic code.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These are in ns so convert from ticks to ns.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These are initialized correctly a couple of lines later in the
function.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c

The bnx2x gso_type setting bug fix in 'net' conflicted with
changes in 'net-next' that broke the gso_* setting logic
out into a seperate function, which also fixes the bug in
question.  Thus, use the 'net-next' version.
Signed-off-by: David S. Miller <davem@davemloft.net>

in htb_change_class() cl->buffer and cl->buffer are stored in ns.
So in dump, convert them back to psched ticks.

Note this was introduced by:
commit 56b765b7
    htb: improved accuracy at high rates

Please consider this for -net/-stable.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Until now, the MPC5200 FEC ethernet driver relied upon the bootloader
(U-Boot) to write the MAC address into the ethernet controller
registers. The Linux driver should not rely on such a thing. So
lets read the MAC address from the DT as it should be done here.

The following priority is now used to read the MAC address:

1) First, try OF node MAC address, if not present or invalid, then:

2) Read from MAC address registers, if invalid, then:

3) Log a warning message, and choose a random MAC address.

This fixes a problem with a MPC5200 board that uses the SPL U-Boot
version without FEC initialization before Linux booting for
boot speedup.

Additionally a status line is now be printed upon successful
driver probing, also displaying this MAC address.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The CPSW switch can act as Dual EMAC by segregating the switch ports
using VLAN and port VLAN as per the TRM description in
14.3.2.10.2 Dual Mac Mode

Following CPSW components will be common for both the interfaces.
* Interrupt source is common for both eth interfaces
* Interrupt pacing is common for both interfaces
* Hardware statistics is common for all the ports
* CPDMA is common for both eth interface
* CPTS is common for both the interface and it should not be enabled on
  both the interface as timestamping information doesn't contain port
  information.

Constrains
* Reserved VID of One port should not be used in other interface which will
  enable switching functionality
* Same VID must not be used in both the interface which will enable switching
  functionality
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As CPTS is common module for both EMAC in Dual EMAC mode so making cpts as
pointer.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* Introduced parameter to add port number for directed packet in cpdma_chan_submit
* Source port detection macro with DMA descriptor status
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
Here is another handful of late-breaking fixes intended for the 3.8
stream...  Hopefully the will still make it! :-)

There are three mac80211 fixes pulled from Johannes:

"Here are three fixes still for the 3.8 stream, the fix from Cong Ding
for the bad sizeof (Stephen Hemminger had pointed it out before but I'd
promptly forgotten), a mac80211 managed-mode channel context usage fix
where a downgrade would never stop until reaching non-HT and a bug in
the channel determination that could cause invalid channels like HT40+
on channel 11 to be used."

Also included is a mwl8k fix that avoids an oops when using mwl8k
devices that only support the 5 GHz band.

Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The original fix that was applied for setting gso_type required more change
than necessary because it was assumed ixgbe does RSC on IPv6 frames and this
is not correct.  RSC is only supported with IPv4/TCP frames only.  As such we
can simplify the fix and avoid the unnecessary move of eth_type_trans.

The previous patch "ixgbe: fix gso type" and this patch reduce the entire fix
to one line that sets gso_type to TCPV4 if the frame is RSC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tommi was fuzzing with trinity and reported the following problem :

commit 3f518bf7 (datagram: Add offset argument to __skb_recv_datagram)
missed that a raw socket receive queue can contain skbs with no payload.

We can loop in __skb_recv_datagram() with MSG_PEEK mode, because
wait_for_packet() is not prepared to skip these skbs.

[   83.541011] INFO: rcu_sched detected stalls on CPUs/tasks: {}
(detected by 0, t=26002 jiffies, g=27673, c=27672, q=75)
[   83.541011] INFO: Stall ended before state dump start
[  108.067010] BUG: soft lockup - CPU#0 stuck for 22s! [trinity-child31:2847]
...
[  108.067010] Call Trace:
[  108.067010]  [<ffffffff818cc103>] __skb_recv_datagram+0x1a3/0x3b0
[  108.067010]  [<ffffffff818cc33d>] skb_recv_datagram+0x2d/0x30
[  108.067010]  [<ffffffff819ed43d>] rawv6_recvmsg+0xad/0x240
[  108.067010]  [<ffffffff818c4b04>] sock_common_recvmsg+0x34/0x50
[  108.067010]  [<ffffffff818bc8ec>] sock_recvmsg+0xbc/0xf0
[  108.067010]  [<ffffffff818bf31e>] sys_recvfrom+0xde/0x150
[  108.067010]  [<ffffffff81ca4329>] system_call_fastpath+0x16/0x1b
Reported-by: Tommi Rantala <tt.rantala@gmail.com>
Tested-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Interface layout:

 00 CD-ROM
 01 debug COM port
 02 AP control port
 03 modem
 04 usb-ethernet

Bus=01 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0408 ProdID=ea42 Rev= 0.00
S:  Manufacturer=Qualcomm, Incorporated
S:  Product=Qualcomm CDMA Technologies MSM
S:  SerialNumber=353568051xxxxxx
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vlad says: The whole multiple cookie keys code is completely unused
and has been all this time. Noone uses anything other then the
secret_key[0] since there is no changeover support anywhere.

Thus, for now clean up its left-over fragments.

Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

With my recent commit I introduced two sparse warnings.  Looking closer there
were a few more in the same file, so I fixed them all up.  Basic rcu pointer
dereferencing suff.

I've validated these changes using CONFIG_PROVE_RCU while starting and stopping
netconsole repeatedly in bonded and non-bonded configurations
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: fengguang.wu@intel.com
CC: David Miller <davem@davemloft.net>
CC: eric.dumazet@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>

__netpoll_rcu_free is used to free netpoll structures when the rtnl_lock is
already held.  The mechanism is used to asynchronously call __netpoll_cleanup
outside of the holding of the rtnl_lock, so as to avoid deadlock.
Unfortunately, __netpoll_cleanup modifies pointers (dev->np), which means the
rtnl_lock must be held while calling it.  Further, it cannot be held, because
rcu callbacks may be issued in softirq contexts, which cannot sleep.

Fix this by converting the rcu callback to a work queue that is guaranteed to
get scheduled in process context, so that we can hold the rtnl properly while
calling __netpoll_cleanup

Tested successfully by myself.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Cong Wang <amwang@redhat.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create skb_panic() function in lieu of both skb_over_panic() and
skb_under_panic() so that code duplication would be avoided. Update type
and variable name where necessary.

Jiri Pirko suggested using wrappers so that we would be able to keep the
fruits of the original code.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

The band field for the supported channels were left unpopulated, making
them default to 0 == IEEE80211_BAND_2GHZ, even for the 5GHz channels.

This resulted in null pointer accesses if anything tries to access
wiphy->bands[channel->band] of a 5GHz channel on 5GHz only cards, since
wiphy->bands[2GHZ] is NULL for them (e.g. cfg80211_chandef_usable does).

Example kernel OOPS:

[  665.669993] Unable to handle kernel NULL pointer dereference at virtual address 00000016
[  665.678194] pgd = c6d58000
[  665.680941] [00000016] *pgd=06f8a831, *pte=00000000, *ppte=00000000
[  665.687303] Internal error: Oops: 17 [#1]
(...)
[  666.116373] Backtrace:
[  666.118866] [<bf0368dc>] (cfg80211_chandef_usable+0x0/0x1bc [cfg80211]) from [<bf025e64>] (nl80211_leave_mesh+0x244/0x264 [cfg80211])
[  666.130919]  r7:c6d12100 r6:0000143c r5:c0611c48 r4:c0611b98
[  666.136668] [<bf025d84>] (nl80211_leave_mesh+0x164/0x264 [cfg80211]) from [<bf02634c>] (nl80211_remain_on_channel+0x2a0/0x358 [cfg80211])
[  666.149074]  r7:c6d12000 r6:c6d12000 r5:c6f4f368 r4:00000003
[  666.154814] [<bf0262ec>] (nl80211_remain_on_channel+0x240/0x358 [cfg80211]) from [<bf02ddb0>] (nl80211_set_wiphy+0x264/0x560 [cfg80211])
[  666.167150] [<bf02db4c>] (nl80211_set_wiphy+0x0/0x560 [cfg80211]) from [<c01f94e0>] (genl_rcv_msg+0x1b8/0x1f8)
[  666.177205] [<c01f9328>] (genl_rcv_msg+0x0/0x1f8) from [<c01f89a0>] (netlink_rcv_skb+0x58/0xb4)
[  666.185949] [<c01f8948>] (netlink_rcv_skb+0x0/0xb4) from [<c01f931c>] (genl_rcv+0x20/0x2c)
[  666.194251]  r6:c6f70780 r5:0000002c r4:c6f70780 r3:00000001
[  666.199973] [<c01f92fc>] (genl_rcv+0x0/0x2c) from [<c01f8418>] (netlink_unicast+0x154/0x1f4)
[  666.208449]  r4:c785ea00 r3:c01f92fc
[  666.212057] [<c01f82c4>] (netlink_unicast+0x0/0x1f4) from [<c01f8790>] (netlink_sendmsg+0x230/0x2b0)
[  666.221240] [<c01f8560>] (netlink_sendmsg+0x0/0x2b0) from [<c01cccf8>] (sock_sendmsg+0x90/0xa4)
[  666.229986] [<c01ccc68>] (sock_sendmsg+0x0/0xa4) from [<c01cdcb0>] (__sys_sendmsg+0x290/0x298)
[  666.238637]  r9:00000000 r8:c0611ec8 r6:0000002c r5:c0610000 r4:c0611f64
[  666.245411] [<c01cda20>] (__sys_sendmsg+0x0/0x298) from [<c01cf52c>] (sys_sendmsg+0x44/0x6c)
[  666.253897] [<c01cf4e8>] (sys_sendmsg+0x0/0x6c) from [<c00090a0>] (ret_fast_syscall+0x0/0x2c)
[  666.262460]  r6:00000000 r5:beeff96c r4:00000005
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Spanning Tree Protocol packets should have always been marked as
control packets, this causes them to get queued in the high prirority
FIFO. As Radia Perlman mentioned in her LCA talk, STP dies if bridge
gets overloaded and can't communicate. This is a long-standing bug back
to the first versions of Linux bridge.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sparse spotted local function that could be static.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes sparse complaints about dropping __user in casts.
 warning: cast removes address space of expression
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

And remove no longer used br->flags.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>