- 03 Mar, 2009 24 commits
-
-
Ron Mercer authored
This interface will be used for setting things like maximum frame size, setting WOL, and ACKing changes requested by the FCOE function. Signed-off-by:
Ron Mercer <ron.mercer@qlogic.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Hantzis Fotis authored
The above functions from include/net/tcp.h have been defined with an argument that they never use. The argument is 'u32 ack' which is never used inside the function body, and thus it can be removed. The rest of the patch involves the necessary changes to the function callers of the above two functions. Signed-off-by:
Hantzis Fotis <xantzis@ceid.upatras.gr> Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
Eilon Greenstein <eilong@broadcom.com> Signed-off-by:
-
Eilon Greenstein authored
Adding "ethtool -d" support. Due to the complexity of the FW and HW, there are a lot of different regions in the chip - to keep the code as clean as possible, the ranges were put in an H file. Some areas cannot be read if the driver is running - so by default, the driver will not access those areas - but any programmer facing a problem will be able to easily manipulate the driver to extract full dump. The full dump can also be used with kernel dump modules in case of kernel panic. Signed-off-by:
-
Eilon Greenstein authored
Add the FP index to relevant debug prints and simply beautify some others Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
Yaniv Rosner <yanivr@broadcom.com> Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
When 8726 module detection option is disabled, module should be transmitting regardless of invalid read from EEPROM Signed-off-by:
-
Eilon Greenstein authored
Microcode download requires write of another register and read from "Limiting/LRM mode" register before setting Signed-off-by:
-
Eilon Greenstein authored
On unload, the FW assumes that no packets will be sent after the driver sends the FW stop command. To ensure that, the driver must always call netif_tx_disable Signed-off-by:
-
Eilon Greenstein authored
Using DMA engine (DMAE) to initialize large consecutive memories in the chip Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Check the napi_poll budget only when updating it. Also add a comment to explain the rmb Signed-off-by:
-
Eilon Greenstein authored
The Tx interrupt is very short and there is no need to limit it to a budget Signed-off-by:
-
Eilon Greenstein authored
Add rmb to read status block indices on load Signed-off-by:
-
Eilon Greenstein authored
As the comment explains, this smb_mb is needed only if the queue is stopped (which is unlikely) so the barrier can be moved to that location Signed-off-by:
-
Eilon Greenstein authored
As noted by Ben Hutchings <bhutchings@solarflare.com>, these are the capabilities offsets and not the ID itself Signed-off-by:
-
Eilon Greenstein authored
As noted by Ben Hutchings <bhutchings@solarflare.com>, these smb_mb are not needed Signed-off-by:
-
David Dillow authored
The conversion to avoid using pci_alloc_consistent() broke the firmware load process, as well as added an order-4 kmalloc and doubled the memory usage of the firmware image. Go back to loading a page at a time. Also, since the user can now give us utter garbage for firmware, do a cursory validation so we don't try to load just anything. Signed-off-by:
David Dillow <dave@thedillows.org> Signed-off-by:
-
Jesse Brandeburg authored
This is in reference to the issue shown in kerneloops (search e1000 unmap) The e1000 transmit code was calling pci_unmap_page on dma handles that it might have called pci_map_single on. Same bug as e1000e Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by:
Bruce Allan <bruce.w.allan@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Jesse Brandeburg authored
This is in reference to https://bugzilla.redhat.com/show_bug.cgi?id=484494 Also addresses issue show in kerneloops The e1000e transmit code was calling pci_unmap_page on dma handles that it might have called pci_map_single on. Signed-off-by:
-
Alexander Duyck authored
Remove skb_orphan call from igb driver as it can cause multiple issues due to the fact that it is calling the desctructor and removing the skb from the socket prior to transmission. The call was added to improve performance but did so by allowing the skb to be removed from the socket which gave the socket more window space to transmit. The performance gain is not worth the extra problems that this kind of workaround can introduce as this could lead to a potential DoS if a UDP stream decided to monopolize the transmit path. Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Acked-by:
Mitch Williams <mitch.a.williams@intel.com> Signed-off-by:
-
- 02 Mar, 2009 16 commits
-
-
Randy Dunlap authored
Fix skbuff.h kernel-doc for timestamps: must include "struct" keyword, otherwise there are kernel-doc errors: Error(linux-next-20090227//include/linux/skbuff.h:161): cannot understand prototype: 'struct skb_shared_hwtstamps ' Error(linux-next-20090227//include/linux/skbuff.h:177): cannot understand prototype: 'union skb_shared_tx ' Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Ben Hutchings authored
Signed-off-by:
Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
-
Ben Hutchings authored
Reinitialise LEDs after overriding them for identification. Rename set_fault_led method to set_id_led since we always use it for NIC identification and not faults. Signed-off-by:
-
Ben Hutchings authored
Signed-off-by:
-
Ben Hutchings authored
This is a new PHY supporting SFP+ modules, used in the SFN4112F reference design. It is similar to the QT2022C2 and shares much of its support code. Signed-off-by:
-
Ben Hutchings authored
Shuffle bits of the OUI into the conventional written order. Replace PHY id component macros with functions. Zero-pad PHY id components in log messages. Signed-off-by:
-
Ben Hutchings authored
Signed-off-by:
-
Ben Hutchings authored
During SFN4111T initialisation, check whether the PHY boot status indicates a bad firmware checksum. If so, prepare to reflash rather than continuing with normal initialisation. Remove redundant PHY boot status check from tenxpress_phy_init(). Signed-off-by:
-
Ben Hutchings authored
Commit 27dd2cac changed mdio_clause45_check_mmds() to read both DEVS0 and DEVS1 registers and to combine their values into an unsigned 32-bit mask. This made the following test for a negative (failure) value useless. Fix it to check whether either read failed. Signed-off-by:
-
Ben Hutchings authored
Signed-off-by:
-
Inaky Perez-Gonzalez authored
Allow the device to give the driver RX data with reorder information. When that is done, the device will indicate the driver if a packet has to be held in a (sorted) queue. It will also tell the driver when held packets have to be released to the OS. This is done to improve the WiMAX-protocol level retransmission support when missing frames are detected. The code docs provide details about the implementation. In general, this just hooks into the RX path in rx.c; if a packet with the reorder bit in the RX header is detected, the reorder information in the header is extracted and one of the four main reorder operations are executed. In one case (queue) no packet will be delivered to the networking stack, just queued, whereas in the others (reset, update_ws and queue_update_ws), queued packet might be delivered depending on the window start for the specific queue. The modifications to files other than rx.c are: - control.c: during device initialization, enable reordering support if the rx_reorder_disabled module parameter is not enabled - driver.c: expose a rx_reorder_disable module parameter and call i2400m_rx_setup/release() to initialize/shutdown RX reorder support. - i2400m.h: introduce members in 'struct i2400m' needed for implementing reorder support. - linux/i2400m.h: introduce TLVs, commands and constant definitions related to RX reorder Last but not least, the rx reorder code includes an small circular log where the last N reorder operations are recorded to be displayed in case of inconsistency. Otherwise diagnosing issues would be almost impossible. Signed-off-by:
Inaky Perez-Gonzalez <inaky@linux.intel.com> Signed-off-by:
-
Harvey Harrison authored
Base versions handle constant folding now. Edited by Inaky to fix conflicts due to changes in netdev.c Signed-off-by:
Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by:
-
Inaky Perez-Gonzalez authored
Newer i2400m firmwares (>= v1.4) extend the data RX protocol so that each packet has a 16 byte header. This header is mainly used to implement host reordeing (which is addressed in later commits). However, this header also allows us to overwrite it (once data has been extracted) with an Ethernet header and deliver to the networking stack without having to reallocate the skb (as it happened in fw <= v1.3) to make room for it. - control.c: indicate the device [dev_initialize()] that the driver wants to use the extended data RX protocol. Also involves adding the definition of the needed data types in include/linux/wimax/i2400m.h. - rx.c: handle the new payload type for the extended RX data protocol. Prepares the skb for delivery to netdev.c:i2400m_net_erx(). - netdev.c: Introduce i2400m_net_erx() that adds the fake ethernet address to a prepared skb and delivers it to the networking stack. - cleanup: in most instances in rx.c, the variable 'single' was renamed to 'single_last' for it better conveys its meaning. Signed-off-by:
-
Kay Sievers authored
Cc: inaky.perez-gonzalez@intel.com Cc: linux-wimax@intel.com Acked-by:
Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by:
Kay Sievers <kay.sievers@vrfy.org> Signed-off-by:
-
Inaky Perez-Gonzalez authored
For power saving reasons, WiMAX links can be put in idle mode while connected after a certain time of the link not being used for tx or rx. In this mode, the device pages the base-station regularly and when data is ready to be transmitted, the link is revived. This patch allows the user to control the time the device has to be idle before it decides to go to idle mode from a sysfs interace. It also updates the initialization code to acknowledge the module variable 'idle_mode_disabled' when the firmware is a newer version (upcoming 1.4 vs 2.6.29's v1.3). The method for setting the idle mode timeout in the older firmwares is much more limited and can be only done at initialization time. Thus, the sysfs file will return -ENOSYS on older ones. Signed-off-by:
-
Inaky Perez-Gonzalez authored
Upcoming modifications will need to test for the running firmware version before activating a feature or not. This is helpful to implement backward compatibility with older firmware versions. Modify i2400m_firmware_check() to encode in i2400m->fw_version the major and minor version numbers of the firmware interface. As well, move the call to be done as the very first operation once we have communication with the device during probe() [in __i2400m_dev_start()]. This is needed so any operation that is executed afterwards can determine which fw version it is talking to. Signed-off-by:
-
