- 28 Sep, 2018 19 commits
-
-
Finn Thain authored
The X3T9.2 specification (draft) says, under "6.1.4.2 RESELECTION time-out procedure", that a target may assert RST or go to BUS FREE phase if the initiator does not respond within 200 us. Something like this has been observed with AztecMonster II target. When it happens, all we can do is wait for the target to try again. Tested-by:
Michael Schmitz <schmitzmic@gmail.com> Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Finn Thain authored
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION", ... The reselected initiator shall then assert the BSY signal within a selection abort time of its most recent detection of being reselected; this is required for correct operation of the time-out procedure. The selection abort time is only 200 us which may be insufficient time for a printk() call. Move the diagnostics to the error paths. Tested-by: -
Finn Thain authored
When NCR5380_abort() returns FAILED, the driver forgets that the target is still busy. Hence, further commands may be sent to the target, which may fail during selection and produce the error message, "reselection after won arbitration?". Prevent this by leaving the busy flag set when NCR5380_abort() fails. Tested-by:
-
Finn Thain authored
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION", that "the initiator shall not respond to a RESELECTION phase if other than two SCSI ID bits are on the DATA BUS." This issue (too many bits set) has been observed in the wild, so add a check. Tested-by:
-
Finn Thain authored
When sense data is valid, call set_driver_byte(cmd, DRIVER_SENSE). Otherwise some callers of scsi_execute() will ignore sense data. Don't set DID_ERROR or DID_RESET just because sense data is missing. Tested-by:
-
Finn Thain authored
This is mostly needed because an AztecMonster II target has been observed disconnecting REQUEST SENSE commands and then failing to reselect properly. Suggested-by:
-
Finn Thain authored
The return value is taken to mean "retry" or "don't retry". Change it to bool to improve readability. Fix related comments. No functional change. Tested-by:
-
Finn Thain authored
Replace a 'goto' statement with a simple 'return' where possible. This improves readability. No functional change. Tested-by:
-
Hannes Reinecke authored
When doing a host reset we should be clearing all outstanding commands, not just the command triggering the reset. [mkp: adjusted Hannes' SoB address] Signed-off-by:
Hannes Reinecke <hare@suse.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Cc: Ondrey Zary <linux@rainbow-software.org> Signed-off-by:
-
Nathan Chancellor authored
Clang warns when multiple pairs of parentheses are used for a single conditional statement. drivers/message/fusion/mptbase.c:338:11: warning: equality comparison with extraneous parentheses [-Wparentheses-equality] if ((ioc == NULL)) ~~~~^~~~~~~ drivers/message/fusion/mptbase.c:338:11: note: remove extraneous parentheses around the comparison to silence this warning if ((ioc == NULL)) ~ ^ ~ drivers/message/fusion/mptbase.c:338:11: note: use '=' to turn this equality comparison into an assignment if ((ioc == NULL)) ^~ = drivers/message/fusion/mptbase.c:342:12: warning: equality comparison with extraneous parentheses [-Wparentheses-equality] if ((pdev == NULL)) ~~~~~^~~~~~~ drivers/message/fusion/mptbase.c:342:12: note: remove extraneous parentheses around the comparison to silence this warning if ((pdev == NULL)) ~ ^ ~ drivers/message/fusion/mptbase.c:342:12: note: use '=' to turn this equality comparison into an assignment if ((pdev == NULL)) ^~ = 2 warnings generated. Remove them and while we're at it, simplify the NULL checks as '!var' is used more than 'var == NULL'. Reported-by:Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Reviewed-by:
-
Colin Ian King authored
The check for a non-zero drvr_wait is redundant as the same check is performed earlier in the outer while loop, the inner check will always be true if we reached this point inside the while loop. Remove the redundant if check. Detected by cppcheck: (warning) Identical inner 'if' condition is always true. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Acked-by:
Manish Rangankar <Manish.Rangankar@cavium.com> Signed-off-by:
-
Giridhar Malavali authored
There is a probability that the SRB structure might have been released by the time the debug log message dereferences it. This patch moved the log messages before the command is issued to the firmware to prevent unknown behavior and kernel crash Fixes: 726b8548 ("qla2xxx: Add framework for async fabric discovery") Cc: <stable@vger.kernel.org> Signed-off-by:
Giridhar Malavali <giridhar.malavali@cavium.com> Reviewed-by:
Ewan D. Milne <emilne@redhat.com> Signed-off-by:
Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by:
-
Giridhar Malavali authored
This patch fixes issue during switch command query where driver was freeing SRB resources multiple times Following stack trace will be seen [ 853.436234] BUG: unable to handle kernel NULL pointer dereference at 0000000000000001 [ 853.436348] IP: [<ffffffff811df514>] kmem_cache_alloc+0x74/0x1e0 [ 853.436476] PGD 0 [ 853.436601] Oops: 0000 [#1] SMP [ 853.454700] [<ffffffff81099f6a>] ? mod_timer+0x14a/0x220 [ 853.455543] [<ffffffff81185465>] mempool_alloc_slab+0x15/0x20 [ 853.456395] [<ffffffff811855a9>] mempool_alloc+0x69/0x170 [ 853.457257] [<ffffffff81098af2>] ? internal_add_timer+0x32/0x70 [ 853.458136] [<ffffffffc0092d2b>] qla2xxx_queuecommand+0x29b/0x3f0 [qla2xxx] [ 853.459024] [<ffffffff8146535a>] scsi_dispatch_cmd+0xaa/0x230 [ 853.459923] [<ffffffff8146e11f>] scsi_request_fn+0x4df/0x680 [ 853.460829] [<ffffffff81029557>] ? __switch_to+0xd7/0x510 [ 853.461747] [<ffffffff812f7113>] __blk_run_queue+0x33/0x40 [ 853.462670] [<ffffffff812f7735>] blk_delay_work+0x25/0x40 [ 853.463603] [<ffffffff810a882a>] process_one_work+0x17a/0x440 [ 853.464546] [<ffffffff810a94f6>] worker_thread+0x126/0x3c0 [ 853.465501] [<ffffffff810a93d0>] ? manage_workers.isra.24+0x2a0/0x2a0 [ 853.466447] [<ffffffff810b099f>] kthread+0xcf/0xe0 [ 853.467379] [<ffffffff810b08d0>] ? insert_kthread_work+0x40/0x40 [ 853.470172] Code: db e2 7e 49 8b 50 08 4d 8b 20 49 8b 40 10 4d 85 e4 0f 84 20 01 00 00 48 85 c0 0f 84 17 01 00 00 49 63 46 20 48 8d 4a 01 4d 8b 06 <49> 8b 1c 04 4c 89 e0 65 49 0f c7 08 0f 94 c0 84 c0 74 ba 49 63 [ 853.472072] RIP [<ffffffff811df514>] kmem_cache_alloc+0x74/0x1e0 [ 853.472971] RSP <ffff88103726fc50> Fixes: 726b8548 ("qla2xxx: Add framework for async fabric discovery") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Quinn Tran authored
This patch prevents user space mailbox request from doing chip reset if the mailbox timed out. The chip reset is only reserved for the DPC thread to ensure all mailbox requests are flushed properly. The DPC thread is responsible for the flushing all MBs and chip reset. Fixes: b2000805 ("scsi: qla2xxx: Flush mailbox commands on chip reset") Cc: <stable@ger.kernel.org> Signed-off-by:
Quinn Tran <quinn.tran@cavium.com> Reviewed-by:
-
Himanshu Madhani authored
This patch fixes multiple call for qla_nvme_unregister_remote_port() as part of qlt_schedule_session_for_deletion(), Do not call it again during qla_nvme_delete() Fixes: e473b307 ("scsi: qla2xxx: Add FC-NVMe abort processing") Cc: <stable@vger.kernel.org> Reviewed-by:
-
Quinn Tran authored
This patch fixes issue where driver clears NPort ID map instead of marking handle in use. Once driver clears NPort ID from the database, it can reuse the same NPort ID resulting in a PLOGI failure. [mkp: fixed Himanshu's SoB] Fixes: a084fd68 ("scsi: qla2xxx: Fix re-login for Nport Handle in use") Cc: <stable@vger.kernel.org> Signed-of-by:
Himanshu Madhani <hmadhani@cavium.com> Signed-off-by:
-
Quinn Tran authored
The response data buffer used in switch scan is reused 4 times. (For example, for commands GPN_FT, GNN_FT for FCP and FC-NVME) Before driver reuses this buffer, clear it to prevent duplicate entries in our database. Fixes: a4239945 ("scsi: qla2xxx: Add switch command to simplify fabric discovery" Cc: <stable@vger.kernel.org> Signed-off-by:
-
Quinn Tran authored
This patch fixes issue when remoteport registers itself as both FCP and FC-NVMe with the switch, driver will pick FC-NVMe personality as default when scanning for targets. Driver was using comaprative operator instead of bitwise operator to check for fc4_type for both FCP and FC-NVME. Fixes: 2b5b9647 ("scsi: qla2xxx: Fix FC-NVMe LUN discovery") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Quinn Tran authored
Send aborts only when chip is active. Fixes: 623ee824 ("scsi: qla2xxx: Fix FC-NVMe IO abort during driver reset") Cc: <stable@vger.kernel.org> # 4.14 Signed-off-by:
-
- 27 Sep, 2018 2 commits
-
-
Dan Carpenter authored
We shouldn't allow negative thresholds. I don't know what it would do but it can't be good. Fixes: 8b4673ba ("scsi: qla2xxx: Add support for ZIO6 interrupt threshold") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
-
Masanari Iida authored
Default value of ql2xasynctmfenable for qla2xxx driver was set to 1 in commit 043dc1d7 ("scsi: qla2xxx: Enable Async TMF processing") but comment in MODULE_PARAM_DESC was not modified. Signed-off-by:
Masanari Iida <standby24x7@gmail.com> Acked-by:
-
- 26 Sep, 2018 9 commits
-
-
Varun Prakash authored
csk leak can happen if a new TCP connection gets established after cxgbit_accept_np() returns, to fix this leak free remaining csk in cxgbit_free_np(). Signed-off-by:
Varun Prakash <varun@chelsio.com> Signed-off-by:
-
Jason Yan authored
When the lldd is processing the complete sas task in interrupt and set the task stat as SAS_TASK_STATE_DONE, the smp timeout timer is able to be triggered at the same time. And smp_task_timedout() will complete the task wheter the SAS_TASK_STATE_DONE is set or not. Then the sas task may freed before lldd end the interrupt process. Thus a use-after-free will happen. Fix this by calling the complete() only when SAS_TASK_STATE_DONE is not set. And remove the check of the return value of the del_timer(). Once the LLDD sets DONE, it must call task->done(), which will call smp_task_done()->complete() and the task will be completed and freed correctly. Reported-by:
chenxiang <chenxiang66@hisilicon.com> Signed-off-by:
Jason Yan <yanaijie@huawei.com> CC: John Garry <john.garry@huawei.com> CC: Johannes Thumshirn <jthumshirn@suse.de> CC: Ewan Milne <emilne@redhat.com> CC: Christoph Hellwig <hch@lst.de> CC: Tomas Henzl <thenzl@redhat.com> CC: Dan Williams <dan.j.williams@intel.com> CC: Hannes Reinecke <hare@suse.com> Reviewed-by:
John Garry <john.garry@huawei.com> Reviewed-by:
-
Jason Yan authored
When ata device IDENTIFY failed, the ata device status is ATA_DEV_UNKNOWN. The libata reported like: [113518.620433] ata5.00: qc timeout (cmd 0xec) [113518.653646] ata5.00: failed to IDENTIFY (I/O error, err_mask=0x4) But libsas verifies the device status by ata_dev_disabled(), which skipped ATA_DEV_UNKNOWN. This will make libsas think the ata device probing succeed the device cannot be actually brought up. And even the new bcast of this device will be considered as flutter and will not probe this device again. Change ata_dev_disabled() to !ata_dev_enabled() so that libsas can deal with this if the ata device probe failed. New bcasts can let us try to probe the device again and bring it up if it is fine to IDENTIFY. Tested-by:
Zhou Yupeng <zhouyupeng1@huawei.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Jason Yan authored
If we went into sas_rediscover_dev() the attached_sas_addr was already insured not to be zero. So it's unnecessary to check if the attached_sas_addr is zero. And although if the sas address is not changed, we always have to unregister the old device when we are going to register a new one. We cannot just leave the device there and bring up the new. Signed-off-by:
-
Jason Yan authored
Now LLDDs have to implement lldd_port_deformed method otherwise NULL dereference will happen. Make it optional and remove the dummy implementation in hisi_sas. Signed-off-by:
-
Jason Yan authored
This code is dead and no clue implies that it will be back again. Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in warning message and comments Signed-off-by:
-
Nathan Chancellor authored
Clang warns when multiple pairs of parentheses are used for a single conditional statement. In file included from drivers/scsi/BusLogic.c:57: drivers/scsi/FlashPoint.c:2947:34: warning: equality comparison with extraneous parentheses [-Wparentheses-equality] if ((currSCCB->Sccb_scsistat == SELECT_SN_ST)) { ~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~ drivers/scsi/FlashPoint.c:2947:34: note: remove extraneous parentheses around the comparison to silence this warning if ((currSCCB->Sccb_scsistat == SELECT_SN_ST)) { ~ ^ ~ drivers/scsi/FlashPoint.c:2947:34: note: use '=' to turn this equality comparison into an assignment if ((currSCCB->Sccb_scsistat == SELECT_SN_ST)) { ^~ = drivers/scsi/FlashPoint.c:2956:39: warning: equality comparison with extraneous parentheses [-Wparentheses-equality] else if ((currSCCB->Sccb_scsistat == ~~~~~~~~~~~~~~~~~~~~~~~~^~ drivers/scsi/FlashPoint.c:2956:39: note: remove extraneous parentheses around the comparison to silence this warning else if ((currSCCB->Sccb_scsistat == ~ ^ drivers/scsi/FlashPoint.c:2956:39: note: use '=' to turn this equality comparison into an assignment else if ((currSCCB->Sccb_scsistat == ^~ = 2 warnings generated. Link: https://github.com/ClangBuiltLinux/linux/issues/156Signed-off-by:Khalid Aziz <khalid@gonehiking.org> Signed-off-by:
-
zhong jiang authored
vmemdup_user is better than duplicating its implementation, So just replace the open code. The issue is detected with the help of Coccinelle. Tested-by:
Don Brace <don.brace@microsemi.com> Acked-by:
zhong jiang <zhongjiang@huawei.com> Signed-off-by:
-
- 21 Sep, 2018 2 commits
-
-
Nathan Chancellor authored
Clang warns when multiple pairs of parentheses are used for a single conditional statement. drivers/scsi/advansys.c:6451:20: warning: equality comparison with extraneous parentheses [-Wparentheses-equality] if ((sdtr_data == 0xFF)) { ~~~~~~~~~~^~~~~~~ drivers/scsi/advansys.c:6451:20: note: remove extraneous parentheses around the comparison to silence this warning if ((sdtr_data == 0xFF)) { ~ ^ ~ drivers/scsi/advansys.c:6451:20: note: use '=' to turn this equality comparison into an assignment if ((sdtr_data == 0xFF)) { ^~ = 1 warning generated. Link: https://github.com/ClangBuiltLinux/linux/issues/155Signed-off-by:Matthew Wilcox <willy@infradead.org> Signed-off-by:
-
Greg Edwards authored
When T10 PI is enabled on a backing device for the iblock backstore, the PI SGL for the entire command is attached to the first bio only. This works fine if the command is covered by a single bio, but can result in ref tag errors in the client for the other bios in a multi-bio command, e.g. [ 47.631236] sda: ref tag error at location 2048 (rcvd 0) [ 47.637658] sda: ref tag error at location 4096 (rcvd 0) [ 47.644228] sda: ref tag error at location 6144 (rcvd 0) The command will be split into multiple bios if the number of data SG elements exceeds BIO_MAX_PAGES (see iblock_get_bio()). The bios may later be split again in the block layer on the host after iblock_submit_bios(), depending on the queue limits of the backing device. The block and SCSI layers will pass through the whole PI SGL down to the LLDD however that first bio is split up, but the LLDD may only use the portion that corresponds to the data length (depends on the LLDD, tested with scsi_debug). Split the PI SGL across the bios in the command, so each bio's bio_integrity_payload contains the protection information for the data in the bio. Use an sg_mapping_iter to keep track of where we are in PI SGL, so we know where to start with the next bio. Signed-off-by:
Greg Edwards <gedwards@ddn.com> Reviewed-by:
Mike Christie <mchristi@redhat.com> Signed-off-by:
-
- 17 Sep, 2018 8 commits
-
-
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/scsi/qla2xxx/qla_iocb.c: In function 'qla24xx_els_dcmd2_iocb': drivers/scsi/qla2xxx/qla_iocb.c:2644:13: warning: variable 'ptr_dma' set but not used [-Wunused-but-set-variable] Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Acked-by:
-
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/scsi/lpfc/lpfc_nvme.c: In function 'lpfc_new_nvme_buf': drivers/scsi/lpfc/lpfc_nvme.c:2238:24: warning: variable 'sgl_size' set but not used [-Wunused-but-set-variable] int bcnt, num_posted, sgl_size; ^ Signed-off-by: -
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/scsi/bnx2fc/bnx2fc_fcoe.c: In function 'bnx2fc_rcv': drivers/scsi/bnx2fc/bnx2fc_fcoe.c:435:17: warning: variable 'oxid' set but not used [-Wunused-but-set-variable] Signed-off-by:
-
Igor Stoppa authored
BUG_ON() already contains an unlikely(), there is no need for another one. Signed-off-by:
Igor Stoppa <igor.stoppa@huawei.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com> Cc: linux-scsi@vger.kernel.org CC: linux-kernel@vger.kernel.org Signed-off-by:
-
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/scsi/aic7xxx/aic79xx_pci.c: In function 'ahd_pci_config': drivers/scsi/aic7xxx/aic79xx_pci.c:291:19: warning: variable 'shared_scb_data' set but not used [-Wunused-but-set-variable] Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in function name and comment Signed-off-by:
-
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/scsi/pm8001/pm80xx_hwi.c: In function 'pm8001_set_phy_profile': drivers/scsi/pm8001/pm80xx_hwi.c:4679:6: warning: variable 'page_code' set but not used [-Wunused-but-set-variable] Signed-off-by:
Jack Wang <jinpu.wang@profitbricks.com> Signed-off-by:
-
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/scsi/pm8001/pm8001_sas.c: In function 'pm8001_I_T_nexus_event_handler': drivers/scsi/pm8001/pm8001_sas.c:1052:6: warning: variable 'device_id' set but not used [-Wunused-but-set-variable] drivers/scsi/pm8001/pm8001_sas.c: In function 'pm8001_abort_task': drivers/scsi/pm8001/pm8001_sas.c:1191:6: warning: variable 'device_id' set but not used [-Wunused-but-set-variable] Signed-off-by:
-
