- 01 Mar, 2010 40 commits
-
-
Christoph Egger authored
The marvell driver comtains a fallback to ahci for the sata ports which is incorrectly checked as CONFIG_AHCI while the only AHCI config item is actually called SATA_AHCI (which also sounds sensible considering it's a fallback for the sata ports). Signed-off-by:
Christoph Egger <siccegge@stud.informatik.uni-erlangen.de> Signed-off-by:
Jeff Garzik <jgarzik@redhat.com>
-
Alan Cox authored
This is needed for some unsupported hardware setups on strange 64bit mainboards where crazy stuff has been done like putting flash ata adapters on the LPC bus, or where the real hardware is hidden/confused. Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
PDC2026x chipsets need the same treatment as PDC20246 one. This is completely untested but will hopefully fix UDMA issues that people have been reporting against pata_pdc202xx_old for the last couple of years. Signed-off-by:
Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
On Monday 04 January 2010 02:30:24 pm Russell King wrote: > Found the problem - getting rid of the read of the alt status register > after the command has been written fixes the UDMA CRC errors on write: > > @@ -676,7 +676,8 @@ void ata_sff_exec_command(struct ata_port *ap, const struct > ata_taskfile *tf) > DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command); > > iowrite8(tf->command, ap->ioaddr.command_addr); > - ata_sff_pause(ap); > + ndelay(400); > +// ata_sff_pause(ap); > } > EXPORT_SYMBOL_GPL(ata_sff_exec_command); > > > This rather makes sense. The PDC20247 handles the UDMA part of the > protocol. It has no way to tell the PDC20246 to wait while it suspends > UDMA, so that a normal register access can take place - the 246 ploughs > on with the register access without any regard to the state of the 247. > > If the drive immediately starts the UDMA protocol after a write to the > command register (as it probably will for the DMA WRITE command), then > we'll be accessing the taskfile in the middle of the UDMA setup, which > can't be good. It's certainly a violation of the ATA specs. Fix it by adding custom ->sff_exec_command method for UDMA33 chipsets. Debugged-by:Russell King <rmk@arm.linux.org.uk> Signed-off-by:
-
Jeff Garzik authored
Noticed and rough patch by Joe Perches. Signed-off-by: -
Bartlomiej Zolnierkiewicz authored
* store UDMA masks in via_isa_bridges[] and while at it make "flags" field to be u8 instead of u16 * convert the driver to use UDMA masks from via_isa_bridges[] * remove no longer needed VIA_UDMA* defines Make some minor documentation and CodingStyle fixes while at it. Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Correct via_do_set_mode() documentation while at it. Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Timing registers should be programmed with the desired number of clocks minus one clock. Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
There shouldn't be any problems with it as IDE cs5535 host driver has been using those values for years and they match values given in the (publicly available) datasheet. Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
s/ARTIM2/ARTTIM23/ in cmd648_bmdma_stop() while at it Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Clear the primary channel pending interrupt bit instead of the reserved one. Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Account for the requirements of the DMA mode currently used by the pair device. Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Fix incorrect handling of recovery clocks value == 16 resulting in overclocked recovery timings & potentially underclocked active timings. Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Use standard cycle timing for CFA PIO5 and PIO6 modes. Based on commit 74638c84 for IDE subsystem. Signed-off-by:
-
Bart Hartgers authored
Before only the timings for master were set. Datasheet can be found here: ftp://ftp.vtbridge.org/Docs/Storage/DS_VT6421A_100_CCPL.PDF Surprisingly, a slave drive works without this patch. According to the datasheet, the controller by default derives the DMA mode from the Set Features command issued to a drive. Not sure about the PIO timings, though. The real problem is that the timings for the master effectively are the ones tuned for the slave. If these support different UDMA-settings, there is trouble, especially when the slave supports a higher UDMA than the master. Anyhow, using the same mechanism for both master and slave seems like a good idea. Signed-off-by:
Bart Hartgers <bart.hartgers@gmail.com> Acked-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Robert Hancock authored
Make some variables in ahci and a function in pata_pcmcia static, as found using sparse. Signed-off-by:
Robert Hancock <hancockrwd@gmail.com> Signed-off-by:
-
Tejun Heo authored
Traditional IDE interface sucks in that it doesn't have a reliable IRQ pending bit, so if the controller raises IRQ while the driver is expecting it not to, the IRQ won't be cleared and eventually the IRQ line will be killed by interrupt subsystem. Some controllers have non-standard mechanism to indicate IRQ pending so that this condition can be detected and worked around. This patch adds an optional operation ->sff_irq_check() which will be called for each port from the ata_sff_interrupt() if an unexpected interrupt is received. If the operation returns %true, ->sff_check_status() and ->sff_irq_clear() will be cleared for the port. Note that this doesn't mark the interrupt as handled so it won't prevent IRQ subsystem from killing the IRQ if this mechanism fails to clear the spurious IRQ. This patch also implements ->sff_irq_check() for ata_piix. Note that this adds slight overhead to shared IRQ operation as IRQs which are destined for other controllers will trigger extra register accesses to check whether IDE interrupt is pending but this solves rare screaming IRQ cases and for some curious reason also helps weird BIOS related glitch on Samsung n130 as reported in bko#14314. http://bugzilla.kernel.org/show_bug.cgi?id=14314 * piix_base_ops dropped as suggested by Sergei. * Spurious IRQ detection doesn't kick in anymore if polling qc is in progress. This provides less protection but some controllers have possible data corruption issues if the wrong register is accessed while a command is in progress. Signed-off-by:
Johannes Stezenbach <js@sig21.net> Reported-by:
Hans Werner <hwerner4@gmx.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by:
-
Tejun Heo authored
host->ports[i] is never NULL if i < host->n_ports and non-NULL return from ata_qc_from_tag() guarantees that the returned qc is active. Drop unnecessary tests. Superflous () dropped as suggested by Sergei. Signed-off-by:
-
Seth Heasley authored
Signed-off-by:
Seth Heasley <seth.heasley@intel.com> Signed-off-by:
-
Seth Heasley authored
Signed-off-by:
-
Shane Huang authored
Tested on AMD internal reference board. Signed-off-by:
Shane Huang <shane.huang@amd.com> Acked-by:
-
Sergei Shtylyov authored
HPT36x chips just don't have DPLL. Signed-off-by:
Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by:
-
Sergei Shtylyov authored
Describe UDMA timing bits 18-20 and 21 separately; add a note to bit 31 about it being meaningful for PIO only. Reformat the whole comment, while at it... Signed-off-by:
-
Sergei Shtylyov authored
There's no need to clear the fast interrupt bit in hpt366_set_mode() since we're doing it in hpt366_init_chipset() already. While at it, rename 'addr1' local variable to 'addr' and exclude 'ap->port_no' from its calculation as HPT36x are single-channel-per-function chips. Signed-off-by:
-
Sergei Shtylyov authored
As these drivers' set_piomode() and set_dmamode() methods are almost identical, factor out the common hpt{37x|3x2n}_set_mode() function to be called by both of them, the same as in 'pata_hpt366' driver. This results in ~5% decrease in the 'pata_hpt37x' driver binary size and in ~4% decrease in the 'pata_hpt3x2n' driver binary size (as measured on x86-32). Signed-off-by: -
Sergei Shtylyov authored
The UltraDMA Tss timing must be stretched with ATA clock of 66 MHz, but the driver only does this when PCI clock is 66 MHz, whereas it always programs DPLL clock (which is used as the ATA clock) to 66 MHz. Signed-off-by:
-
Sergei Shtylyov authored
Use ATA_DMA_* constants instead of the bare numbers for the BMIDE registers. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhostLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: virtio: fix out of range array access
-
Linus Torvalds authored
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (100 commits) ARM: Eliminate decompressor -Dstatic= PIC hack ARM: 5958/1: ARM: U300: fix inverted clk round rate ARM: 5956/1: misplaced parentheses ARM: 5955/1: ep93xx: move timer defines into core.c and document ARM: 5954/1: ep93xx: move gpio interrupt support to gpio.c ARM: 5953/1: ep93xx: fix broken build of clock.c ARM: 5952/1: ARM: MM: Add ARM_L1_CACHE_SHIFT_6 for handle inside each ARCH Kconfig ARM: 5949/1: NUC900 add gpio virtual memory map ARM: 5948/1: Enable timer0 to time4 clock support for nuc910 ARM: 5940/2: ARM: MMCI: remove custom DBG macro and printk ARM: make_coherent(): fix problems with highpte, part 2 MM: Pass a PTE pointer to update_mmu_cache() rather than the PTE itself ARM: 5945/1: ep93xx: include correct irq.h in core.c ARM: 5933/1: amba-pl011: support hardware flow control ARM: 5930/1: Add PKMAP area description to memory.txt. ARM: 5929/1: Add checks to detect overlap of memory regions. ARM: 5928/1: Change type of VMALLOC_END to unsigned long. ARM: 5927/1: Make delimiters of DMA area globally visibly. ARM: 5926/1: Add "Virtual kernel memory..." printout. ARM: 5920/1: OMAP4: Enable L2 Cache ... Fix up trivial conflict in arch/arm/mach-mx25/clock.c
-
git://git.kernel.dk/linux-2.6-blockLinus Torvalds authored
* 'for-2.6.34' of git://git.kernel.dk/linux-2.6-block: (38 commits) block: don't access jiffies when initialising io_context cfq: remove 8 bytes of padding from cfq_rb_root on 64 bit builds block: fix for "Consolidate phys_segment and hw_segment limits" cfq-iosched: quantum check tweak blktrace: perform cleanup after setup error blkdev: fix merge_bvec_fn return value checks cfq-iosched: requests "in flight" vs "in driver" clarification cciss: Fix problem with scatter gather elements in the scsi half of the driver cciss: eliminate unnecessary pointer use in cciss scsi code cciss: do not use void pointer for scsi hba data cciss: factor out scatter gather chain block mapping code cciss: fix scatter gather chain block dma direction kludge cciss: simplify scatter gather code cciss: factor out scatter gather chain block allocation and freeing cciss: detect bad alignment of scsi commands at build time cciss: clarify command list padding calculation cfq-iosched: rethink seeky detection for SSDs cfq-iosched: rework seeky detection block: remove padding from io_context on 64bit builds block: Consolidate phys_segment and hw_segment limits ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (252 commits) ASoC: Check progress when reporting periods from i.MX FIQ handler ASoC: Remove a unused variables from i.MX FIQ runtime data ALSA: hda - Add/fix ALC269 FSC and Quanta models ALSA: hda - Add ALC670 codec support OMAP4: PMIC: Add support for twl6030 codec ALSA: hda - remove unnecessary msleep on power state transitions usb/gadget/{f_audio,gmidi}.c: follow recent changes in audio.h ASoC: fsi: Modify over/under run error settlement ASoC: OMAP4: Add McPDM platform driver ASoC: OMAP4: Add support for McPDM ASoC: OMAP: data_type and sync_mode configurable in audio dma ALSA: hda - Add missing description in HD-Audio-Models.txt ALSA: add support for Macbook Air 2,1 internal speaker ALSA: usbaudio: consolidate header files ALSA: usbmixer: bail out early when parsing audio class v2 descriptors ALSA: usbaudio: implement basic set of class v2.0 parser ALSA: usbaudio: introduce new types for audio class v2 ALSA: usbaudio: parse USB descriptors with structs ALSA: hda - enable snoop for Intel Cougar Point ALSA: hda - Remove identical definitions for macmini3 model ...
-
Linus Torvalds authored
Merge branches 'futexes-for-linus', 'irq-core-for-linus' and 'bkl-drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'futexes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: futex: Protect pid lookup in compat code with RCU * 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: genirq: Fix documentation of default chip disable() * 'bkl-drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: nvram: Drop the BKL from nvram_open()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tipLinus Torvalds authored
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: posix-timers.c: Don't export local functions clocksource: start CMT at clocksource resume clocksource: add suspend callback clocksource: add argument to resume callback ntp: Cleanup xtime references in ntp.c ntp: Make time_esterror and time_maxerror static
-
Randy Dunlap authored
Add missing kernel-doc notation for new function parameters: Warning(drivers/scsi/scsi.c:1031): No description found for parameter 'buf' Warning(drivers/scsi/scsi.c:1031): No description found for parameter 'buf_len' Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Cc: James Bottomley <James.Bottomley@suse.de> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Yinghai Lu authored
A ROM resource that doesn't fit should not cause us to try to re-assign all the bus resources. Nobody generally cares, and re-assigning is going to just cause way more troubles than it tries to solve. Signed-off-by:
Yinghai Lu <yinghai@kernel.org> Signed-off-by:
-
Takashi Iwai authored
-
