Like cpumap use xdp_release_frame() when an xdp_frame got
converted into an SKB and send towars the network stack.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When converting an xdp_frame into an SKB, and sending this into the network
stack, then the underlying XDP memory model need to release associated
resources, because the network stack don't have callbacks for XDP memory
models.  The only memory model that needs this is page_pool, when a driver
use the DMA-mapping feature.

Introduce page_pool_release_page(), which basically does the same as
page_pool_unmap_page(). Add xdp_release_frame() as the XDP memory model
interface for calling it, if the memory model match MEM_TYPE_PAGE_POOL, to
save the function call overhead for others. Have cpumap call
xdp_release_frame() before xdp_scrub_frame().
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix error handling case, where inserting ID with rhashtable_insert_slow
fails in xdp_rxq_info_reg_mem_model, which leads to never releasing the IDA
ID, as the lookup in xdp_rxq_info_unreg_mem_model fails and thus
ida_simple_remove() is never called.

Fix by releasing ID via ida_simple_remove(), and mark xdp_rxq->mem.id with
zero, which is already checked in xdp_rxq_info_unreg_mem_model().
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

On a previous patch dma addr was stored in 'struct page'.
Use that to unmap DMA addresses used by network drivers
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On a previous patch dma addr was stored in 'struct page'.
Use that to retrieve DMA addresses used by network drivers
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netsec_process_rx was running in a loop trying to process as many packets
as possible before re-enabling interrupts. With the recent DMA changes
this is not needed anymore as we manage to consume all the budget without
looping over the function.
Since it has no performance penalty let's remove that and simplify the Rx
path a bit
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since we changed the Tx ring handling and now depends on bit31 to figure
out the owner of the descriptor, we should initialize this every time
the device goes down-up instead of doing it once on driver init. If the
value is not correctly initialized the device won't have any available
descriptors

Changes since v1:
- Typo fixes

Fixes: 35e07d23 ("net: socionext: remove mmio reads on Tx")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The comment is correct, but the code ends up moving the bits four
places too far, into the VTUOp field.

Fixes: bec8e572 (net: dsa: mv88e6xxx: implement vtu_getnext and vtu_loadpurge for mv88e6250)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use _BITUL() instead.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Implement flower ingress device matching offload

Jiri says:

In case of using shared block, user might find it handy to be able to insert
filters to match on particular ingress device. This patchset exposes the
ingress ifindex through flow_dissector and flow_offload so mlxsw can use it to
push down to HW. See the selftests for examples of usage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend tc_flower to test plain ingress device matching and also
tc_shblock to test ingress device matching on shared block.
Add new tc_flower_router.sh where ingress device matching on egress
(after routing) is done.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Benefit from the previously extended flow_dissector infrastructure and
offload matching on ingress port.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the size of the SRC_SYS_PORT element to be 16.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RX_ACL_SYSTEM_PORT is 8 bit but SRC_SYS_PORT is 16 bits. Internally,
SRC_SYS_PORT is used to carry the value. Relax the checker in case of
RX_ACL_SYSTEM_PORT and allow different size.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RX_ACL_SYSTEM_PORT is equal to SRC_SYS_PORT - 1. So before write to
block we need to adjust the key value. Introduce new "EXT" helper to
implement this.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement support for previously added flow dissector meta key.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use previously introduced infra to obtain and store ingress ifindex
instead doing it locally.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new key meta that contains ingress ifindex value and add a function
to dissect this from skb. The key and function is prepared to cover
other potential skb metadata values dissection.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function mlx5_devlink_alloc is missing a void argument, add it
to clean up the non-ANSI function declaration.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Maxime Chevallier says:

====================
net: mvpp2: cls: Allow steering based on vlan tag

The PPv2 classifier can perform flow steering based on keys extracted
from the VLAN tag. This series adds support for using the vlan id and
the vlan prio as keys, using the ethtool interface.

Patch 1 is a preparatory patch that prevent false-positive matches,
using a dedicated lookup id for the RSS C2 lookup.

Patch 2 allows to separate the flows based on the header fields they
contain. The main goal is to be able to separate tagged traffic from
untagged traffic for flow steering, just as we already do for RSS.

Patch 3 solves an issue we have when extracting fields that aren't full
bytes, such as the vlan tag which is 12 bits wide, or the priority which
is 3 bits wide.

Finally, patch 4 adds support for steering based on both vlan id and
priority, extracted from the outermost tag.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit allows using the vlan Id and priority as parts of the key
for classification offload. These fields are extracted from the
outermost tag, if multiple tags are present.

Vlan Id and priority are considered as 2 different fields by the
classifier, however the fields are both appended in the Header Extracted
Key in the same layout as they are found in the tags. This means that
when steering only based on the prio, a 16-bit slot is still taken in
the HEK.

The classifier doesn't allow extracting the DEI bit from the tag, so we
explicitly prevent user from using this bit in the key.

This commit adds the vlan priotity as a compatible HEK field for
tagged traffic, meaning that we limit the possibility of extracting this
field only to the flows that contain tagged traffic.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The C2 TCAM used for classification uses a key (Header Extracted Key)
built by concatenating several fields extracted from the packet header.

After a lot of trial-and-error and some guess work, it seems the HEK is
right justified, with the first fields being stored in the MSB, then
concatenated up until the LSB.

Until now, this doesn't cause any issue since all HEK fields we use are
full bytes. However this is an issue for the upcoming VLAN id and pri
extraction, which aren't full bytes.

Rework the way we built that TCAM key, by changing the order in which we
append the fields.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The way we currently handle classification offload and RSS is by having
dedicated lookup sequences in the flow table, each being selected
depending on several fields being present in the packet header.

We need to make sure the classification operation we want to perform can
be done in each flow we want to insert it into. As an example,
classifying on VLAN tag can only be done on flows used for tagged
traffic.

This commit makes sure we don't insert rules in flows we aren't
compatible with.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When performing a TCAM lookup in the C2 engine, it's possible that
multiple entries match the packet. To make sure the correct entry match
when performing a lookup, the Flow Table can set a lookup type, which
will be used in the TCAM lookup, thus preventing such false-positives.

We need to make sure the RSS match doesn't interfere with other
classification lookups, hence we use a dedicated lookup_type for it.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yash Shah says:

====================
Add macb support for SiFive FU540-C000

On FU540, the management IP block is tightly coupled with the Cadence
MACB IP block. It manages many of the boundary signals from the MACB IP
This patchset controls the tx_clk input signal to the MACB IP. It
switches between the local TX clock (125MHz) and PHY TX clocks. This
is necessary to toggle between 1Gb and 100/10Mb speeds.

Future patches may add support for monitoring or controlling other IP
boundary signals.

This patchset is mostly based on work done by
Wesley Terpstra <wesley@sifive.com>

This patchset is based on Linux v5.2-rc1 and tested on HiFive Unleashed
board with additional board related patches needed for testing can be
found at dev/yashs/ethernet_v3 branch of:
https://github.com/yashshah7/riscv-linux.git

Change History:
V3:
- Revert "MACB_SIFIVE_FU540" config changes in Kconfig and driver code.
  The driver does not depend on SiFive GPIO driver.

V2:
- Change compatible string from "cdns,fu540-macb" to "sifive,fu540-macb"
- Add "MACB_SIFIVE_FU540" in Kconfig to support SiFive FU540 in macb
  driver. This is needed because on FU540, the macb driver depends on
  SiFive GPIO driver.
- Avoid writing the result of a comparison to a register.
- Fix the issue of probe fail on reloading the module reported by:
  Andreas Schwab <schwab@suse.de>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The management IP block is tightly coupled with the Cadence MACB IP
block on the FU540, and manages many of the boundary signals from the
MACB IP. This patch only controls the tx_clk input signal to the MACB
IP. Future patches may add support for monitoring or controlling other
IP boundary signals.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the compatibility string documentation for SiFive FU540-C0000
interface.
On the FU540, this driver also needs to read and write registers in a
management IP block that monitors or drives boundary signals for the
GEMGXL IP block that are not directly mapped to GEMGXL registers.
Therefore, add additional range to "reg" property for SiFive GEMGXL
management IP registers.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xue Chaojing says:

====================
hinic: add rss support and rss parameters configuration

This series add rss support for HINIC driver and implement the ethtool
interface related to rss parameter configuration. user can use ethtool
configure rss parameters or show rss parameters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support rss parameters with ethtool,
user can change hash key, hash indirection table, hash
function by ethtool -X, and show rss parameters by ethtool -x.
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves ethtool code from hinic_main.c to hinic_ethtool.c
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds rss support for the HINIC driver.
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the call to device_property_read_u32_array is not error checked
leading to potential garbage values in the delays array that are then used
in msleep delays.  Add a sanity check to the property fetching.

Addresses-Coverity: ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"git diff" says:

    \ No newline at end of file

after modifying the file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

A previous attempt to shut up the uninitialized variable use
warning was apparently insufficient. When CONFIG_PROFILE_ANNOTATED_BRANCHES
is set, gcc-8 still warns, because the unlikely() check in DP_NOTICE()
causes it to no longer track the state of all variables correctly:

drivers/net/ethernet/qlogic/qed/qed_dev.c: In function 'qed_llh_set_ppfid_affinity':
drivers/net/ethernet/qlogic/qed/qed_dev.c:798:47: error: 'abs_ppfid' may be used uninitialized in this function [-Werror=maybe-uninitialized]
  addr = NIG_REG_PPF_TO_ENGINE_SEL + abs_ppfid * 0x4;
                                     ~~~~~~~~~~^~~~~

This is not a nice workaround, but always initializing the output from
qed_llh_abs_ppfid() at least shuts up the false positive reliably.

Fixes: 79284ade ("qed: Add llh ppfid interface and 100g support for offload protocols")
Fixes: 8e2ea3ea ("qed: Fix static checker warning")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Flexible array members should be denoted using [] instead of [0], else
gcc will not warn when they are no longer at the end of a struct.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

in IPoIB case we can't see a VF broadcast address for but
can see for PF

Before:
11: ib1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast
state UP mode DEFAULT group default qlen 256
    link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd
00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
    vf 0 MAC 14:80:00:00:66:fe, spoof checking off, link-state disable,
trust off, query_rss off
...

After:
11: ib1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast
state UP mode DEFAULT group default qlen 256
    link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd
00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
    vf 0     link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd
00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff, spoof
checking off, link-state disable, trust off, query_rss off

v1->v2: add the IFLA_VF_BROADCAST constant
v2->v3: put IFLA_VF_BROADCAST at the end
to avoid KABI breakage and set NLA_REJECT
dev_setlink
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

in the case of IPoIB with SRIOV enabled hardware
ip link show command incorrecly prints
0 instead of a VF hardware address.

Before:
11: ib1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast
state UP mode DEFAULT group default qlen 256
    link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd
00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
    vf 0 MAC 00:00:00:00:00:00, spoof checking off, link-state disable,
trust off, query_rss off
...
After:
11: ib1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast
state UP mode DEFAULT group default qlen 256
    link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd
00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
    vf 0     link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd
00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff, spoof
checking off, link-state disable, trust off, query_rss off

v1->v2: just copy an address without modifing ifla_vf_mac
v2->v3: update the changelog
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Improve IPv6 route insertion rate

Unlike IPv4, an IPv6 multipath route in the kernel is composed from
multiple sibling routes, each representing a single nexthop.

Therefore, an addition of a multipath route with N nexthops translates
to N in-kernel notifications. This is inefficient for device drivers
that need to program the route to the underlying device. Each time a new
nexthop is appended, a new nexthop group needs to be constructed and the
old one deleted.

This patchset improves the situation by sending a single notification
for a multipath route addition / deletion instead of one per-nexthop.
When adding thousands of multipath routes with 16 nexthops, I measured
an improvement of about x10 in the insertion rate.

Patches #1-#3 add a flag that indicates that in-kernel notifications
need to be suppressed and extend the IPv6 FIB notification info with
information about the number of sibling routes that are being notified.

Patches #4-#5 adjust the two current listeners to these notifications to
ignore notifications about IPv6 multipath routes.

Patches #6-#7 adds add / delete notifications for IPv6 multipath routes.

Patches #8-#14 do the same for mlxsw.

Patch #15 finally removes the limitations added in patches #4-#5 and
stops the kernel from sending a notification for each added / deleted
nexthop.

Patch #16 adds test cases.

v2 (David Ahern):
* Remove patch adjusting netdevsim to consume resources for each
  fib6_info. Instead, consume one resource for the entire multipath
  route
* Remove 'multipath_rt' usage in patch #10
* Remove 'multipath_rt' from 'struct fib6_entry_notifier_info' in patch
  #15. The member is only removed in this patch to prevent drivers from
  processing multipath routes twice during the series
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that the offload indication for unicast routes is correctly set in
different scenarios. IPv4 support will be added in the future.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both listeners - mlxsw and netdevsim - of IPv6 FIB notifications are now
ready to handle IPv6 multipath notifications.

Therefore, stop ignoring such notifications in both drivers and stop
sending notification for each added / deleted nexthop.

v2:
* Remove 'multipath_rt' from 'struct fib6_entry_notifier_info'
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>