- 10 Feb, 2015 23 commits
-
-
Sylwester Nawrocki authored
commit fddcd300 upstream. I2S1, I2S2 on Exynos4 SoC series have limited functionality compared to I2S0, "samsung,s3c6410-i2s" compatible should be used for them. Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Myron Stowe authored
commit 06cf35f9 upstream. Some AMD CS553x devices have read-only BARs because of a firmware or hardware defect. There's a workaround in quirk_cs5536_vsa(), but it no longer works after 36e81648 ("PCI: Restore detection of read-only BARs"). Prior to 36e81648, we filled in res->start; afterwards we leave it zeroed out. The quirk only updated the size, so the driver tried to use a region starting at zero, which didn't work. Expand quirk_cs5536_vsa() to read the base addresses from the BARs and hard-code the sizes. On Nix's system BAR 2's read-only value is 0x6200. Prior to 36e81648, we interpret that as a 512-byte BAR based on the lowest-order bit set. Per datasheet sec 5.6.1, that BAR (MFGPT) requires only 64 bytes; use that to avoid clearing any address bits if a platform uses only 64-byte alignment. [bhelgaas: changelog, reduce BAR 2 size to 64] Fixes: 36e81648 ("PCI: Restore detection of read-only BARs") Link: https://bugzilla.kernel.org/show_bug.cgi?id=85991#c4 Link: http://support.amd.com/TechDocs/31506_cs5535_databook.pdf Link: http://support.amd.com/TechDocs/33238G_cs5536_db.pdfReported-and-tested-by:
Nix <nix@esperi.org.uk> Signed-off-by:
Myron Stowe <myron.stowe@redhat.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Eric Nelson authored
commit 58cc9c9a upstream. To quote from section 1.3.1 of the data sheet: The SGTL5000 has an internal reset that is deasserted 8 SYS_MCLK cycles after all power rails have been brought up. After this time, communication can start ... 1.0us represents 8 SYS_MCLK cycles at the minimum 8.0 MHz SYS_MCLK. Signed-off-by:
Eric Nelson <eric.nelson@boundarydevices.com> Reviewed-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Will Deacon authored
commit 8e648066 upstream. Commit e1a5848e ("ARM: 7924/1: mm: don't bother with reserved ttbr0 when running with LPAE") removed the use of the reserved TTBR0 value for LPAE systems, since the ASID is held in the TTBR and can be updated atomicly with the pgd of the next mm. Unfortunately, this patch forgot to update flush_context, which deliberately avoids marking the local active ASID as allocated, since we used to switch via ASID zero and didn't need to allocate the ASID of the previous mm. The side-effect of this is that we can allocate the same ASID to the next mm and, between flushing the local TLB and updating TTBR0, we can perform speculative TLB fills for userspace nG mappings using the page table of the previous mm. The consequence of this is that the next mm can erroneously hit some mappings of the previous mm. Note that this was made significantly harder to hit by a391263c ("ARM: 8203/1: mm: try to re-use old ASID assignments following a rollover") but is still theoretically possible. This patch fixes the problem by removing the code from flush_context that forces the allocated ASID to zero for the local CPU. Many thanks to the Broadcom guys for tracking this one down. Fixes: e1a5848e ("ARM: 7924/1: mm: don't bother with reserved ttbr0 when running with LPAE") Reported-by:
Raymond Ngun <rngun@broadcom.com> Tested-by:
Gregory Fong <gregory.0xf0@gmail.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Alex Deucher authored
commit a124d068 upstream. Should be the same as cayman. We don't use VM by default on NI parts so this isn't critical. Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 544143f9 upstream. If acceleration is disabled, it does not make sense to init gpuvm since nothing will use it. Moreover, if radeon_vm_init() gets called it uses accel to try and clear the pde tables, etc. which results in a bug. v2: handle vm_fini as well v3: handle bo_open/close as well Bug: https://bugs.freedesktop.org/show_bug.cgi?id=88786Signed-off-by:
-
Christian König authored
commit 72edd83c upstream. This is a workaround for RS880 and older chips which seem to have an additional limit on the minimum PLL input frequency. v2: fix signed/unsigned warning bugs: https://bugzilla.kernel.org/show_bug.cgi?id=91861 https://bugzilla.kernel.org/show_bug.cgi?id=83461Signed-off-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Charlotte Richardson authored
commit 51ac3d2f upstream. NEC OEMs the same platforms as Stratus does, which have multiple devices on some PCIe buses under downstream ports. Link: https://bugzilla.kernel.org/show_bug.cgi?id=51331 Fixes: 1278998f ("PCI: Work around Stratus ftServer broken PCIe hierarchy (fix DMI check)") Signed-off-by:
Charlotte Richardson <charlotte.richardson@stratus.com> Signed-off-by:
-
NeilBrown authored
commit b1b02fe9 upstream. If a non-page-aligned write is destined for a device which is missing/faulty, we can deadlock. As the target device is missing, a read-modify-write cycle is not possible. As the write is not for a full-page, a recontruct-write cycle is not possible. This should be handled by logic in fetch_block() which notices there is a non-R5_OVERWRITE write to a missing device, and so loads all blocks. However since commit 67f45548, that code requires STRIPE_PREREAD_ACTIVE before it will active, and those circumstances never set STRIPE_PREREAD_ACTIVE. So: in handle_stripe_dirtying, if neither rmw or rcw was possible, set STRIPE_DELAYED, which will cause STRIPE_PREREAD_ACTIVE be set after a suitable delay. Fixes: 67f45548Reported-by:
Mikulas Patocka <mpatocka@redhat.com> Tested-by:
Heinz Mauelshagen <heinzm@redhat.com> Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
Johan Hovold authored
commit 49d2ca84 upstream. Fix memory leak in the gpio sysfs interface due to failure to drop reference to device returned by class_find_device when setting the gpio-line polarity. Fixes: 07697461 ("gpiolib: add support for changing value polarity in sysfs") Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> [ luis: backported to 3.16: - file rename: drivers/gpio/gpiolib-sysfs.c -> drivers/gpio/gpiolib.c ] Signed-off-by:
-
Johan Hovold authored
commit 0f303db0 upstream. Fix memory leak in the gpio sysfs interface due to failure to drop reference to device returned by class_find_device when creating a link. Fixes: a4177ee7 ("gpiolib: allow exported GPIO nodes to be named using sysfs links") Signed-off-by:
-
Hemmo Nieminen authored
commit c7754e75 upstream. As printk() invocation can cause e.g. a TLB miss, printk() cannot be called before the exception handlers have been properly initialized. This can happen e.g. when netconsole has been loaded as a kernel module and the TLB table has been cleared when a CPU was offline. Call cpu_report() in start_secondary() only after the exception handlers have been initialized to fix this. Without the patch the kernel will randomly either lockup or crash after a CPU is onlined and the console driver is a module. Signed-off-by:
Hemmo Nieminen <hemmo.nieminen@iki.fi> Signed-off-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Cc: David Daney <david.daney@cavium.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/8953/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
karl beldan authored
commit 9ce35779 upstream. Fixed commit added from64to32 under _#ifndef do_csum_ but used it under _#ifndef csum_tcpudp_nofold_, breaking some builds (Fengguang's robot reported TILEGX's). Move from64to32 under the latter. Fixes: 150ae0e9 ("lib/checksum.c: fix carry in csum_tcpudp_nofold") Reported-by:
kbuild test robot <fengguang.wu@intel.com> Signed-off-by:
Karl Beldan <karl.beldan@rivierawaves.com> Cc: Eric Dumazet <edumazet@google.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
karl beldan authored
commit 150ae0e9 upstream. The carry from the 64->32bits folding was dropped, e.g with: saddr=0xFFFFFFFF daddr=0xFF0000FF len=0xFFFF proto=0 sum=1, csum_tcpudp_nofold returned 0 instead of 1. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Takashi Iwai authored
commit 4161b450 upstream. When ak4114 work calls its callback and the callback invokes ak4114_reinit(), it stalls due to flush_delayed_work(). For avoiding this, control the reentrance by introducing a refcount. Also flush_delayed_work() is replaced with cancel_delayed_work_sync(). The exactly same bug is present in ak4113.c and fixed as well. Reported-by:
Pavel Hofman <pavel.hofman@ivitera.com> Acked-by:
Jaroslav Kysela <perex@perex.cz> Tested-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Bhuvanchandra DV authored
commit 973fbce6 upstream. devm_* API was supposed to be used only in probe function call. Memory is allocated at 'probe' and free automatically at 'remove'. Usage of devm_* functions outside probe sometimes leads to memory leak. Avoid using devm_kzalloc in dspi_setup_transfer and use kzalloc instead. Also add the dspi_cleanup function to free the controller data upon cleanup. Acked-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Signed-off-by:
-
Bo Shen authored
commit a43bd7e1 upstream. According to the I2S specification information as following: - WS = 0, channel 1 (left) - WS = 1, channel 2 (right) So, the start event should be TF/RF falling edge. Reported-by:
Songjun Wu <songjun.wu@atmel.com> Signed-off-by:
Bo Shen <voice.shen@atmel.com> Signed-off-by:
-
Lai Jiangshan authored
commit 4bee9686 upstream. The following race exists in the smpboot percpu threads management: CPU0 CPU1 cpu_up(2) get_online_cpus(); smpboot_create_threads(2); smpboot_register_percpu_thread(); for_each_online_cpu(); __smpboot_create_thread(); __cpu_up(2); This results in a missing per cpu thread for the newly onlined cpu2 and in a NULL pointer dereference on a consecutive offline of that cpu. Proctect smpboot_register_percpu_thread() with get_online_cpus() to prevent that. [ tglx: Massaged changelog and removed the change in smpboot_unregister_percpu_thread() because that's an optimization and therefor not stable material. ] Signed-off-by:
Lai Jiangshan <laijs@cn.fujitsu.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Cc: David Rientjes <rientjes@google.com> Link: http://lkml.kernel.org/r/1406777421-12830-1-git-send-email-laijs@cn.fujitsu.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Sachin Prabhu authored
commit ca7df8e0 upstream. Commit c11f1df5 requires writers to wait for any pending oplock break handler to complete before proceeding to write. This is done by waiting on bit CIFS_INODE_PENDING_OPLOCK_BREAK in cifsFileInfo->flags. This bit is cleared by the oplock break handler job queued on the workqueue once it has completed handling the oplock break allowing writers to proceed with writing to the file. While testing, it was noticed that the filehandle could be closed while there is a pending oplock break which results in the oplock break handler on the cifsiod workqueue being cancelled before it has had a chance to execute and clear the CIFS_INODE_PENDING_OPLOCK_BREAK bit. Any subsequent attempt to write to this file hangs waiting for the CIFS_INODE_PENDING_OPLOCK_BREAK bit to be cleared. We fix this by ensuring that we also clear the bit CIFS_INODE_PENDING_OPLOCK_BREAK when we remove the oplock break handler from the workqueue. The bug was found by Red Hat QA while testing using ltp's fsstress command. Signed-off-by:
Sachin Prabhu <sprabhu@redhat.com> Acked-by:
Shirish Pargaonkar <shirishpargaonkar@gmail.com> Signed-off-by:
Jeff Layton <jlayton@samba.org> Signed-off-by:
Steve French <steve.french@primarydata.com> Signed-off-by:
-
Felix Fietkau authored
commit a3e6c1ef upstream. If the irq_chip does not define .irq_disable, any call to disable_irq will defer disabling the IRQ until it fires while marked as disabled. This assumes that the handler function checks for this condition, which handle_percpu_irq does not. In this case, calling disable_irq leads to an IRQ storm, if the interrupt fires while disabled. This optimization is only useful when disabling the IRQ is slow, which is not true for the MIPS CPU IRQ. Disable this optimization by implementing .irq_disable and .irq_enable Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/8949/Signed-off-by:
-
Mark Rutland authored
commit 44b82b77 upstream. [backport to 3.16.x: fold in missing MIDR_EL1 recording] Commit d7a49086 (arm64: cpuinfo: print info for all CPUs) attempted to clean up /proc/cpuinfo, but due to concerns regarding further changes was reverted in commit 5e39977e (Revert "arm64: cpuinfo: print info for all CPUs"). There are two major issues with the arm64 /proc/cpuinfo format currently: * The "Features" line describes (only) the 64-bit hwcaps, which is problematic for some 32-bit applications which attempt to parse it. As the same names are used for analogous ISA features (e.g. aes) despite these generally being architecturally unrelated, it is not possible to simply append the 64-bit and 32-bit hwcaps in a manner that might not be misleading to some applications. Various potential solutions have appeared in vendor kernels. Typically the format of the Features line varies depending on whether the task is 32-bit. * Information is only printed regarding a single CPU. This does not match the ARM format, and does not provide sufficient information in big.LITTLE systems where CPUs are heterogeneous. The CPU information printed is queried from the current CPU's registers, which is racy w.r.t. cross-cpu migration. This patch attempts to solve these issues. The following changes are made: * When a task with a LINUX32 personality attempts to read /proc/cpuinfo, the "Features" line contains the decoded 32-bit hwcaps, as with the arm port. Otherwise, the decoded 64-bit hwcaps are shown. This aligns with the behaviour of COMPAT_UTS_MACHINE and COMPAT_ELF_PLATFORM. In the absense of compat support, the Features line is empty. The set of hwcaps injected into a task's auxval are unaffected. * Properties are printed per-cpu, as with the ARM port. The per-cpu information is queried from pre-recorded cpu information (as used by the sanity checks). * As with the previous attempt at fixing up /proc/cpuinfo, the hardware field is removed. The only users so far are 32-bit applications tied to particular boards, so no portable applications should be affected, and this should prevent future tying to particular boards. The following differences remain: * No model_name is printed, as this cannot be queried from the hardware and cannot be provided in a stable fashion. Use of the CPU {implementor,variant,part,revision} fields is sufficient to identify a CPU and is portable across arm and arm64. * The following system-wide properties are not provided, as they are not possible to provide generally. Programs relying on these are already tied to particular (32-bit only) boards: - Hardware - Revision - Serial No software has yet been identified for which these remaining differences are problematic. Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Ian Campbell <ijc@hellion.org.uk> Signed-off-by:
Mark Rutland <mark.rutland@arm.com> [Mark: backport to v3.16.x] Signed-off-by:
-
Richard Guy Briggs authored
commit 63f13448 upstream. Since both ppc and ppc64 have LE variants which are now reported by uname, add that flag (__AUDIT_ARCH_LE) to syscall_get_arch() and add AUDIT_ARCH_PPC64LE variant. Without this, perf trace and auditctl fail. Mainline kernel reports ppc64le (per a0588015) but there is no matching AUDIT_ARCH_PPC64LE. Since 32-bit PPC LE is not supported by audit, don't advertise it in AUDIT_ARCH_PPC* variants. See: https://www.redhat.com/archives/linux-audit/2014-August/msg00082.html https://www.redhat.com/archives/linux-audit/2014-December/msg00004.htmlSigned-off-by:
Richard Guy Briggs <rgb@redhat.com> Acked-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> [bwh: Backported to 3.16: arch is passed in by do_syscall_trace_enter() rather than queried by calling syscall_get_arch()] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Tested-by:
-
Luis Henriques authored
Signed-off-by:
-
- 04 Feb, 2015 17 commits
-
-
Hannes Frederic Sowa authored
commit df4d9254 upstream. Not caching dst_entries which cause redirects could be exploited by hosts on the same subnet, causing a severe DoS attack. This effect aggravated since commit f8864972 ("ipv4: fix dst race in sk_dst_get()"). Lookups causing redirects will be allocated with DST_NOCACHE set which will force dst_release to free them via RCU. Unfortunately waiting for RCU grace period just takes too long, we can end up with >1M dst_entries waiting to be released and the system will run OOM. rcuos threads cannot catch up under high softirq load. Attaching the flag to emit a redirect later on to the specific skb allows us to cache those dst_entries thus reducing the pressure on allocation and deallocation. This issue was discovered by Marcelo Leitner. Cc: Julian Anastasov <ja@ssi.bg> Signed-off-by:
Marcelo Leitner <mleitner@redhat.com> Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
Julian Anastasov <ja@ssi.bg> Signed-off-by:
-
Hans de Goede authored
commit 841e11cc upstream. Wifi on this laptop does not work unless asus-nb-wmi.wapf=4 is specified on the kerne commandline, add a quirk for this. BugLink: https://bugs.launchpad.net/bugs/1173681Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Darren Hart <dvhart@linux.intel.com> Signed-off-by:
-
Stanislaw Gruszka authored
commit 4ec7a45b upstream. X550VB as many others Asus laptops need wapf4 quirk to make RFKILL switch be functional. Otherwise system boots with wireless card disabled and is only possible to enable it by suspend/resume. Bug report: http://bugzilla.redhat.com/show_bug.cgi?id=1089731#c23Reported-and-tested-by:
Vratislav Podzimek <vpodzime@redhat.com> Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Hans de Goede authored
commit 831a444e upstream. As reported here: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1173681 the U32U needs wapf=4 too. Signed-off-by:
Matthew Garrett <matthew.garrett@nebula.com> Signed-off-by:
-
Hans de Goede authored
commit 378008df upstream. The actual x401u does not use the so named x401u quirk but the x55u quirk. All that the x401u quirk does it setting wapf to 4, so rename it to wapf4 to stop the confusion. Signed-off-by:
-
Hans de Goede authored
commit 6d6ded3b upstream. As reported here: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1173681 the X550CC needs wapf=4 too. Signed-off-by:
-
Hans de Goede authored
commit 22ba58c8 upstream. As reported here: https://bugs.launchpad.net/bugs/1277959 the X550CL needs wapf=4 too. Signed-off-by:
-
AceLan Kao authored
commit c66263a3 upstream. BIOS won't light on the wifi-led after S3, so asus-wmi driver needs to control the wifi and wifi-led status. But, it'll lead to bt status error if asus-wmi driver controls bt as well. So, for X200CA, asus-wmi driver controls wifi status only and have to set wapf to 1. Signed-off-by:
AceLan Kao <acelan.kao@canonical.com> Signed-off-by:
-
poma authored
commit 7216e102 upstream. The 'asus-nb-wmi' WAPF parameter must be set to 4, so the internal Wireless LAN device is operational. Signed-off-by:
poma <pomidorabelisima@gmail.com> Signed-off-by:
-
Greg Thelen authored
commit 0346dadb upstream. Commit e61734c5 ("cgroup: remove cgroup->name") added two extra newlines to memcg oom kill log messages. This makes dmesg hard to read and parse. The issue affects 3.15+. Example: Task in /t <<< extra #1 killed as a result of limit of /t <<< extra #2 memory: usage 102400kB, limit 102400kB, failcnt 274712 Remove the extra newlines from memcg oom kill messages, so the messages look like: Task in /t killed as a result of limit of /t memory: usage 102400kB, limit 102400kB, failcnt 240649 Fixes: e61734c5 ("cgroup: remove cgroup->name") Signed-off-by:
Greg Thelen <gthelen@google.com> Acked-by:
Michal Hocko <mhocko@suse.cz> Acked-by:
Johannes Weiner <hannes@cmpxchg.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Daniel Borkmann authored
commit 600ddd68 upstream. When hitting an INIT collision case during the 4WHS with AUTH enabled, as already described in detail in commit 1be9a950 ("net: sctp: inherit auth_capable on INIT collisions"), it can happen that we occasionally still remotely trigger the following panic on server side which seems to have been uncovered after the fix from commit 1be9a950 ... [ 533.876389] BUG: unable to handle kernel paging request at 00000000ffffffff [ 533.913657] IP: [<ffffffff811ac385>] __kmalloc+0x95/0x230 [ 533.940559] PGD 5030f2067 PUD 0 [ 533.957104] Oops: 0000 [#1] SMP [ 533.974283] Modules linked in: sctp mlx4_en [...] [ 534.939704] Call Trace: [ 534.951833] [<ffffffff81294e30>] ? crypto_init_shash_ops+0x60/0xf0 [ 534.984213] [<ffffffff81294e30>] crypto_init_shash_ops+0x60/0xf0 [ 535.015025] [<ffffffff8128c8ed>] __crypto_alloc_tfm+0x6d/0x170 [ 535.045661] [<ffffffff8128d12c>] crypto_alloc_base+0x4c/0xb0 [ 535.074593] [<ffffffff8160bd42>] ? _raw_spin_lock_bh+0x12/0x50 [ 535.105239] [<ffffffffa0418c11>] sctp_inet_listen+0x161/0x1e0 [sctp] [ 535.138606] [<ffffffff814e43bd>] SyS_listen+0x9d/0xb0 [ 535.166848] [<ffffffff816149a9>] system_call_fastpath+0x16/0x1b ... or depending on the the application, for example this one: [ 1370.026490] BUG: unable to handle kernel paging request at 00000000ffffffff [ 1370.026506] IP: [<ffffffff811ab455>] kmem_cache_alloc+0x75/0x1d0 [ 1370.054568] PGD 633c94067 PUD 0 [ 1370.070446] Oops: 0000 [#1] SMP [ 1370.085010] Modules linked in: sctp kvm_amd kvm [...] [ 1370.963431] Call Trace: [ 1370.974632] [<ffffffff8120f7cf>] ? SyS_epoll_ctl+0x53f/0x960 [ 1371.000863] [<ffffffff8120f7cf>] SyS_epoll_ctl+0x53f/0x960 [ 1371.027154] [<ffffffff812100d3>] ? anon_inode_getfile+0xd3/0x170 [ 1371.054679] [<ffffffff811e3d67>] ? __alloc_fd+0xa7/0x130 [ 1371.080183] [<ffffffff816149a9>] system_call_fastpath+0x16/0x1b With slab debugging enabled, we can see that the poison has been overwritten: [ 669.826368] BUG kmalloc-128 (Tainted: G W ): Poison overwritten [ 669.826385] INFO: 0xffff880228b32e50-0xffff880228b32e50. First byte 0x6a instead of 0x6b [ 669.826414] INFO: Allocated in sctp_auth_create_key+0x23/0x50 [sctp] age=3 cpu=0 pid=18494 [ 669.826424] __slab_alloc+0x4bf/0x566 [ 669.826433] __kmalloc+0x280/0x310 [ 669.826453] sctp_auth_create_key+0x23/0x50 [sctp] [ 669.826471] sctp_auth_asoc_create_secret+0xcb/0x1e0 [sctp] [ 669.826488] sctp_auth_asoc_init_active_key+0x68/0xa0 [sctp] [ 669.826505] sctp_do_sm+0x29d/0x17c0 [sctp] [...] [ 669.826629] INFO: Freed in kzfree+0x31/0x40 age=1 cpu=0 pid=18494 [ 669.826635] __slab_free+0x39/0x2a8 [ 669.826643] kfree+0x1d6/0x230 [ 669.826650] kzfree+0x31/0x40 [ 669.826666] sctp_auth_key_put+0x19/0x20 [sctp] [ 669.826681] sctp_assoc_update+0x1ee/0x2d0 [sctp] [ 669.826695] sctp_do_sm+0x674/0x17c0 [sctp] Since this only triggers in some collision-cases with AUTH, the problem at heart is that sctp_auth_key_put() on asoc->asoc_shared_key is called twice when having refcnt 1, once directly in sctp_assoc_update() and yet again from within sctp_auth_asoc_init_active_key() via sctp_assoc_update() on the already kzfree'd memory, which is also consistent with the observation of the poison decrease from 0x6b to 0x6a (note: the overwrite is detected at a later point in time when poison is checked on new allocation). Reference counting of auth keys revisited: Shared keys for AUTH chunks are being stored in endpoints and associations in endpoint_shared_keys list. On endpoint creation, a null key is being added; on association creation, all endpoint shared keys are being cached and thus cloned over to the association. struct sctp_shared_key only holds a pointer to the actual key bytes, that is, struct sctp_auth_bytes which keeps track of users internally through refcounting. Naturally, on assoc or enpoint destruction, sctp_shared_key are being destroyed directly and the reference on sctp_auth_bytes dropped. User space can add keys to either list via setsockopt(2) through struct sctp_authkey and by passing that to sctp_auth_set_key() which replaces or adds a new auth key. There, sctp_auth_create_key() creates a new sctp_auth_bytes with refcount 1 and in case of replacement drops the reference on the old sctp_auth_bytes. A key can be set active from user space through setsockopt() on the id via sctp_auth_set_active_key(), which iterates through either endpoint_shared_keys and in case of an assoc, invokes (one of various places) sctp_auth_asoc_init_active_key(). sctp_auth_asoc_init_active_key() computes the actual secret from local's and peer's random, hmac and shared key parameters and returns a new key directly as sctp_auth_bytes, that is asoc->asoc_shared_key, plus drops the reference if there was a previous one. The secret, which where we eventually double drop the ref comes from sctp_auth_asoc_set_secret() with intitial refcount of 1, which also stays unchanged eventually in sctp_assoc_update(). This key is later being used for crypto layer to set the key for the hash in crypto_hash_setkey() from sctp_auth_calculate_hmac(). To close the loop: asoc->asoc_shared_key is freshly allocated secret material and independant of the sctp_shared_key management keeping track of only shared keys in endpoints and assocs. Hence, also commit 4184b2a7 ("net: sctp: fix memory leak in auth key management") is independant of this bug here since it concerns a different layer (though same structures being used eventually). asoc->asoc_shared_key is reference dropped correctly on assoc destruction in sctp_association_free() and when active keys are being replaced in sctp_auth_asoc_init_active_key(), it always has a refcount of 1. Hence, it's freed prematurely in sctp_assoc_update(). Simple fix is to remove that sctp_auth_key_put() from there which fixes these panics. Fixes: 730fc3d0 ("[SCTP]: Implete SCTP-AUTH parameter processing") Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Acked-by:
Vlad Yasevich <vyasevich@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Guenter Roeck authored
commit e262eb93 upstream. Fix misspelled define. Fixes: 33692f27 ("vm: add VM_FAULT_SIGSEGV handling support") Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Emmanuel Grumbach authored
commit 4e6c48e0 upstream. This change has already been implemented in iwldvm: commit a260e7b3f0307878b99d57ed1406cf2d497923b8 Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Date: Sun Oct 5 09:11:14 2014 +0300 iwlwifi: dvm: drop non VO frames when flushing Since I added the flush() callback implementation in mvm, we got reports that the queues are stuck while roaming or suspending. This commit above helped much for iwldvm, implement the same behavior for iwlmvm. Fixes: c5b0e7c0 ("iwlwifi: mvm: implement mac80211's flush callback") Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> [ luis: backport to 3.16 provided by Emmanuel ] Signed-off-by:
-
Catalin Marinas authored
commit d6ad3691 upstream. Commit 0b46b8a7 (clocksource: arch_timer: Fix code to use physical timers when requested) introduces the use of physical counters in the ARM architected timer driver. However, he arm64 kernel uses CNTVCT in VDSO. When booting in EL2, the kernel switches to the physical timers to make things easier for KVM but it continues to use the virtual counter both in user and kernel. While in such scenario CNTVCT == CNTPCT (since CNTVOFF is initialised by the kernel to 0), we want to spot firmware bugs corrupting CNTVOFF early (which would affect CNTVCT). Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Tested-by:
Yingjoe Chen <yingjoe.chen@mediatek.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by:
-
Peter Zijlstra authored
commit c3c87e77 upstream. The fix from 9fc81d87 ("perf: Fix events installation during moving group") was incomplete in that it failed to recognise that creating a group with events for different CPUs is semantically broken -- they cannot be co-scheduled. Furthermore, it leads to real breakage where, when we create an event for CPU Y and then migrate it to form a group on CPU X, the code gets confused where the counter is programmed -- triggered in practice as well by me via the perf fuzzer. Fix this by tightening the rules for creating groups. Only allow grouping of counters that can be co-scheduled in the same context. This means for the same task and/or the same cpu. Fixes: 9fc81d87 ("perf: Fix events installation during moving group") Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/20150123125834.090683288@infradead.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Rasmus Villemoes authored
commit e87c3f80 upstream. !strncmp(buf, "force host", 9) is true if and only if buf starts with "force hos". This was obviously not what was intended. The same error exists for "force full-speed", "force high-speed" and "test packet". Using strstarts avoids the error-prone hardcoding of the prefix length. For consistency, also change the other occurences of the !strncmp idiom. Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Dan Carpenter authored
commit fc625960 upstream. Both "dev->udev" and "interface->dev" are NULL. These printks are not very interesting so I just deleted them. Fixes: 03270634 ('USB: Add ADU support for Ontrak ADU devices') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
