Use mailbox to read/write CLOS_PM_QOS_CONFIG instead of read/write to
MMIO offset.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There is an expectation in the CLX platform for SST base-freq feature that
Scaling min frequency be different for high and low priority cores.
This is the way the firmware will understand the priority.

So this change will look at high priority and low priority cores, and set
scaling_min_freq to P1High for high priority cores and P1Low to low
priority cores.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

In CLX_N base_frequency is read from cpufreq sysfs, where units are in
KHz. The internal units in the code matches the real ratios which are
in 100MHz scale. So when storing units for CLX-N frequencies, convert
to 100MHz scale.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Make the avx level display consistent. Except for "turbo-ratio-limits-avx",
everywhere else it is avx2. So change "turbo-ratio-limits-avx"
to "turbo-ratio-limits-avx2".
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Add support for uncore P0, uncore P1, P1 for base and AVX levels and
memory frequency. These commands are optional, so continue on
failure.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Add touchscreen platform data for the Schneider SCT101CTM tablet
Signed-off-by: Daniel Gorbea <danielgorbea@hotmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.

For chained irqchips this is a pretty straight-forward
conversion. This driver requests the IRQ directly in the driver
so it needs to pass a NULL parent handler. We may revisit this
code later and pull reqular shared IRQ handler into
gpiolib, so leave a FIXME.

Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There is no need to have a label to return an error code in one case.
Moreover the other places in the same function do not utilize that label.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Use devm_platform_ioremap_resource() to simplify the code a bit.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

battery_lock mutex is never used and not needed.

Fixes: 355a070b ("platform/x86: huawei-wmi: Add battery charging thresholds")
Signed-off-by: Ayman Bagabas <ayman.bagabas@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

No need to check for battery name, we already check if the WMI function is
available in huawei_wmi_battery_setup.

Fixes: 355a070b ("platform/x86: huawei-wmi: Add battery charging thresholds")
Signed-off-by: Ayman Bagabas <ayman.bagabas@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Check if battery thresholds are within 0 and 100.

Fixes: 355a070b ("platform/x86: huawei-wmi: Add battery charging thresholds")
Signed-off-by: Ayman Bagabas <ayman.bagabas@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Rename Peter Feuerer to Peter Kaestle.

Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Kaestle <peter@piie.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Add support for Acer Aspire 7551.

Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Signed-off-by: Peter Feuerer <peter@piie.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Add functionality for base-freq info|enable|disable info on CascadeLake-N.

Sample output:
Intel(R) Speed Select Technology
Executing on CPU model:85[0x55]
 package-0
  die-0
    cpu-0
      speed-select-base-freq
        high-priority-base-frequency(MHz):2700000
        high-priority-cpu-mask:00000000,0000e8c0
        high-priority-cpu-list:6,7,11,13,14,15
        low-priority-base-frequency(MHz):2100000
 package-1
  die-0
    cpu-20
      speed-select-base-freq
        high-priority-base-frequency(MHz):2700000
        high-priority-cpu-mask:0000000e,8c000000
        high-priority-cpu-list:26,27,31,33,34,35
        low-priority-base-frequency(MHz):2100000

The enable command always returns success, and the disable command always
returns failed because SST-BF cannot be enabled or disabled from the OS on
CascadeLake-N.

Enable command also have support for --auto|-a option, which sets cpufreq
scaling_min to max, so that the high priority base frequency can be the
required minimum for high priority cores. Disable command with -a/--auto
option reset the setting back to the min frequency.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Add functionality for "perf-profile info" on CascadeLake-N.

Sample output:
intel-speed-select perf-profile info
Intel(R) Speed Select Technology
Executing on CPU model:85[0x55]
 package-0
  die-0
    cpu-0
      perf-profile-level-0
        cpu-count:20
        enable-cpu-mask:00000000,000fffff
        enable-cpu-list:0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19
        thermal-design-power-ratio:23
        base-frequency(MHz):2300
        speed-select-turbo-freq:unsupported
        speed-select-base-freq:enabled
        speed-select-base-freq
          high-priority-base-frequency(MHz):2700000
          high-priority-cpu-mask:00000000,0000e8c0
          high-priority-cpu-list:6,7,11,13,14,15
          low-priority-base-frequency(MHz):2100000
 package-1
  die-0
    cpu-20
      perf-profile-level-0
        cpu-count:20
        enable-cpu-mask:000000ff,fff00000
        enable-cpu-list:20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39
        thermal-design-power-ratio:23
        base-frequency(MHz):2300
        speed-select-turbo-freq:unsupported
        speed-select-base-freq:enabled
        speed-select-base-freq
          high-priority-base-frequency(MHz):2700000
          high-priority-cpu-mask:0000000e,8c000000
          high-priority-cpu-list:26,27,31,33,34,35
          low-priority-base-frequency(MHz):2100000
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

CascadeLake-N only supports SST-BF and needs some of the perf-profile
commands, and the base-freq commands.

Add help functions, and create an empty command structures (the functions
will be implemented later in this patchset).  Call these functions
when running on CascadeLake-N.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Three CascadeLake-N models (6252N, 6230N, and 5218N) have SST-PBF support.

Return an error if the CascadeLake processor is not one of these specific
models.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Make the process_command take any help command and command list.  This
will make it easier to help commands and a command list for CascadeLake-N.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

The current code structure has similar but separate command functions for
the enable and disable operations.  This can be improved by adding an int
argument to the command function structure, and interpreting 1 as enable
and 0 as disable.  This change results in the removal of the disable
command functions.

Add int argument to the command function structure.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

The turbo-freq feature is dependent on the core-power feature. If the
core-power feature is disabled while the turbo-freq feature is enabled,
this will break the turbo-freq feature. This is a firmware limitation,
where they can't return error under this scenario.

So when trying to disable core-power, make sure that the turbo-freq
feature is not enabled. If it enabled, return error if user is trying to
disable the core-power feature.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Introduce --auto|-a option to turbo-freq enable feature, so that it
does in one step for users who are OK by setting all passed target cores
as high priority and set in CLOS 0 and remaining in CLOS 3. In this way,
users don't have to take multiple steps to enable turbo-freq feature. For
users who want more fine grain control, they can always use core-power
feature to set custom CLOS configuration and assignment.

While here also print the error to output when clos configuration fails.

For example
intel-speed-select -c 0-4 turbo-freq enable --auto

The above command will enable turbo-freq and core-power feature. Also
mark CPU 0 to CPU 4 as high priority.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Introduce --auto|-a option to base-freq enable feature, so that it
does in one step for users who are OK by setting all cores with higher
base frequency to be set in CLOS 0 and remaining in CLOS 3. This option
also sets corresponding clos.min to CLOS 0 and CLOS3. In this way, users
don't have to take multiple steps to enable base-freq feature. For users
who want more fine grain control, they can always use core-power feature
to set custom CLOS configuration and assignment.

Also adjust cpufreq/scaling_min_freq for higher and lower priority cores.

For example user can use:
intel-speed-select base-freq enable --auto
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Fix warning for:
isst-config.c: In function ‘set_cpu_online_offline’:
isst-config.c:221:3: warning: ignoring return value of ‘write’,
declared with attribute warn_unused_result [-Wunused-result]
   write(fd, "1\n", 2);
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Add System76 ACPI driver, which adds support for Fn-Fx key
combinations, keyboard backlight, and airplane mode LEDs
on System76 laptops running open source firmware.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Cc: platform-driver-x86@vger.kernel.org
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

This was supposed to be precision "%.*s" instead of width "%*s".  It's
possible that this results in printing beyond the end of the string.

Fixes: a970b95345ab ("platform/x86: huawei-wmi: Add debugfs support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There is no need to access global variable directly when we may derive it
through other means.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

There is no need to keep a pointer to the platform device. Currently there are
no users of it directly, and if there will be in the future we may restore it
from pointer to the struct device.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

We have to clean memory resources allocated during init.

Fixes: 7532afb35012 ("platform/x86: huawei-wmi: Move to platform driver")
Cc: Ayman Bagabas <ayman.bagabas@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Fixes: 7532afb35012 ("platform/x86: huawei-wmi: Move to platform driver")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

For APIC case of interrupt we don't fail a ->probe() of the driver,
which makes kernel to print a lot of warnings from the children.

We have two options here:
- switch to platform_get_irq_optional(), though it won't stop children
  to be probed and failed
- fail the ->probe() of i2c-multi-instantiate

Since the in reality we never had devices in the wild where IRQ resource
is optional, the latter solution suits the best.

Fixes: 799d3379 ("platform/x86: i2c-multi-instantiate: Introduce IOAPIC IRQ support")
Reported-by: Ammy Yi <ammy.yi@intel.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>

Since the commit

  7723f4c5 ("driver core: platform: Add an error message to platform_get_irq*()")

the platform_get_irq() started issuing an error message which is not
what we want here.

Switch to platform_get_irq_optional() to have only warning message
provided by the driver.

Fixes: 7723f4c5 ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

This commit adds the bootctl platform driver for Mellanox BlueField
Soc, which queries secure state and controls the eMMC boot partition
swapping by sending SMC calls to ATF running at EL3.

Below are the sequences of typical use case.

  1. User requests boot partition swapping, which could be on-demand or
     during boot-image upgrade via UEFI capsule;

  2. This bootctl driver handles the request and sends SMC call
     to ATF. ATF programs register BREADCRUMB0 which has value
     preserved during warm reset. It also programs eMMC to swap
     the boot partition;

  3. After software reset (rebooting), ATF BL1 (BootRom) checks
     register BREADCRUMB0 and enable watchdog if configured;

  4. If booting fails, the watchdog timer will trigger rebooting.
     In such case, ATF Boot ROM will switch the boot partition
     back to the previous one. This is a robust feature and used
     to prevent failure during boot partition upgrade.
Reviewed-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/platform/x86/classmate-laptop.c: In function cmpc_accel_remove_v4:
drivers/platform/x86/classmate-laptop.c:424:21: warning: variable accel
set but not used [-Wunused-but-set-variable]
drivers/platform/x86/classmate-laptop.c: In function cmpc_accel_remove:
drivers/platform/x86/classmate-laptop.c:660:21: warning: variable accel
set but not used [-Wunused-but-set-variable]

In function cmpc_accel_remove_v4 and cmpc_accel_remove, variable accel is
set but not used, so it can be removed. In that case, variable inputdev is
set but not used and can be removed.

Fixes: 7125587d ("classmate-laptop: Add support for Classmate V4 accelerometer.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Existing intel_cht_int33fe ACPI pseudo-device driver assumes that
hardware has Type-C connector and register related devices described as
I2C connections in the _CRS resource.

There is at least one hardware (Lenovo Yoga Book YB1-91L/F) with Micro-B
USB connector exists. It has INT33FE device in the DSDT table but
there are only two I2C connection described: PMIC and BQ27452 battery
fuel gauge.

Splitting existing INT33FE driver allow to maintain code for USB Micro-B
(or AB) connector variant separately and make it simpler.

Split driver to intel_cht_int33fe_common.c and
intel_cht_int33fe_{microb,typec}.c. Compile all this sources to one .ko
module to make user experience easier.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

The driver does not use polling mode of input devices, and this config
option is going away, so let's not reference it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

We have added polled mode to the normal input devices with the intent of
retiring input_polled_dev. This converts peaq-wmi driver to use the
polling mode of standard input devices and removes dependency on
INPUT_POLLDEV.

Because the new polling coded does not allow peeking inside the poller
structure to get the poll interval, we change the "debounce" process to
operate on the time basis, instead of counting events.

We also fix error handling during initialization, as previously we leaked
input device structure when we failed to register it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

We have added polled mode to the normal input devices with the intent of
retiring input_polled_dev. This converts hdaps driver to use the
polling mode of standard input devices and removes dependency on
INPUT_POLLDEV.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

We have added polled mode to the normal input devices with the intent of
retiring input_polled_dev. This converts Asus laptop driver to use the
polling mode of standard input devices and removes dependency on
INPUT_POLLDEV.

Also removed no longed needed set_bit(EV_ABS, ...) as
input_set_abs_oarams() does it for us.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

This patch adds a quirk disabling keyboard backlight support for the
Dell Inspiron 1012 and 1018.

Those models wrongly report supporting keyboard backlight control
features (through SMBIOS tokens) even though they're not equipped with
a backlit keyboard. This led to broken controls being exposed
through sysfs by this driver which froze the system when used.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=107651Signed-off-by: Pacien TRAN-GIRARD <pacien.trangirard@pacien.net>
Reviewed-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>