- 22 Jan, 2023 30 commits
-
-
Laurent Pinchart authored
Macros are easier to read than numerical values. Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by:
Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@kernel.org>
-
Laurent Pinchart authored
Add support for 12-bit raw bayer formats to the driver, configuring the GMSL format accordingly. Signed-off-by:
Jacopo Mondi <jacopo.mondi@ideasonboard.com> Signed-off-by:
-
Laurent Pinchart authored
The MAX9286_DATATYPE_RAW11 value is used to configure the MAX9286 for 11-bit or 12-bit input data. While 11-bit data is supported on the GMSL side, CSI-2 doesn't have a RAW11 format. 11-bit data is transferred over CSI-2 as RAW12. Rename the macro accordingly to avoid confusion. Signed-off-by:
-
Laurent Pinchart authored
The MAX9286 can generate a framesync signal to synchronize the cameras, using an internal timer. Support this mode of operation and configure it through the .s_frameinterval() operation. If the frame interval is not 0, framesync is switched to manual mode with the specified interval, otherwise automatic mode is used. Signed-off-by:
-
Thomas Nizan authored
Allow users to use one PoC regulator per port, instead of a global regulator. The properties '^port[0-3]-poc-supply$' in the DT node are used to indicate the regulators for individual ports. Signed-off-by:
Thomas Nizan <tnizan@witekio.com> Signed-off-by:
-
Laurent Pinchart authored
The GMSL serial data bus width is normally selected by the BWS pin, but it can also be configured by software. Add a DT property that allows overriding the value of the BWS-selected bus width to support systems whose BWS pin doesn't result in the correct value. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Laurent Pinchart authored
The I2C speed on the remote side (the I2C master bus of the connected serializers) is configurable, and doesn't need to match the speed of the local bus (the slave bus of the MAX9286). All remote buses must use the same speed, and the MAX9286 needs to be programmed accordingly. Add a new DT property to select the speed to make it configurable. Signed-off-by:
-
Laurent Pinchart authored
Power supplies for the ports can be controlled per port depending on the hardware design. Support per-port supplies in the DT bindings, mutually exclusive with the global supply. Signed-off-by:
-
Mauro Carvalho Chehab authored
Merge tag 'media-uvc-next-20230115' of git://git.kernel.org/pub/scm/linux/kernel/git/pinchartl/linux into media_stage uvcvideo fixes and improvements * tag 'media-uvc-next-20230115' of git://git.kernel.org/pub/scm/linux/kernel/git/pinchartl/linux: (27 commits) media: uvcvideo: Silence memcpy() run-time false positive warnings media: uvcvideo: Quirk for autosuspend in Logitech B910 and C910 media: uvcvideo: Fix race condition with usb_kill_urb media: uvcvideo: Use standard names for menus media: uvcvideo: Fix power line control for Lenovo Integrated Camera media: uvcvideo: Refactor power_line_frequency_controls_limited media: uvcvideo: Refactor uvc_ctrl_mappings_uvcXX media: uvcvideo: Implement mask for V4L2_CTRL_TYPE_MENU media: uvcvideo: Extend documentation of uvc_video_clock_decode() media: uvcvideo: Limit power line control for Acer EasyCamera media: uvcvideo: Refactor __uvc_ctrl_add_mapping media: uvcvideo: Fix handling on Bitmask controls media: uvcvideo: Do not return positive errors in uvc_query_ctrl() media: uvcvideo: Return -EACCES for Wrong state error media: uvcvideo: Improve error logging in uvc_query_ctrl() media: uvcvideo: Check for INACTIVE in uvc_ctrl_is_accessible() media: uvcvideo: Factor out usb_string() calls media: uvcvideo: Limit power line control for Acer EasyCamera media: uvcvideo: Recover stalled ElGato devices media: uvcvideo: Remove void casting for the status endpoint ... Signed-off-by:
-
Uwe Kleine-König authored
A remove callback just returning 0 is equivalent to no remove callback at all. So drop the useless function. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Jean Delvare authored
Since commit 0166dc11 ("of: make CONFIG_OF user selectable"), it is possible to test-build any driver which depends on OF on any architecture by explicitly selecting OF. Therefore depending on COMPILE_TEST as an alternative is no longer needed. It is actually better to always build such drivers with OF enabled, so that the test builds are closer to how each driver will actually be built on its intended target. Building them without OF may not test much as the compiler will optimize out potentially large parts of the code. In the worst case, this could even pop false positive warnings. Dropping COMPILE_TEST here improves the quality of our testing and avoids wasting time on non-existent issues. As a minor optimization, this also lets us drop of_match_ptr(), as we now know what it will resolve to, we might as well save cpp some work. Signed-off-by:
Jean Delvare <jdelvare@suse.de> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de> Acked-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
Matt Ranostay <matt.ranostay@konsulko.com> Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. [hverkuil: remove obsolete kerneldoc 'id' documentation] Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
Akihiro Tsukada <tskd08@gmail.com> Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
- 15 Jan, 2023 10 commits
-
-
Kees Cook authored
The memcpy() in uvc_video_decode_meta() intentionally copies across the length and flags members and into the trailing buf flexible array. Split the copy so that the compiler can better reason about (the lack of) buffer overflows here. Avoid the run-time false positive warning: memcpy: detected field-spanning write (size 12) of single field "&meta->length" at drivers/media/usb/uvc/uvc_video.c:1355 (size 1) Additionally fix a typo in the documentation for struct uvc_meta_buf. Reported-by: ionut_n2001@yahoo.com Link: https://bugzilla.kernel.org/show_bug.cgi?id=216810Signed-off-by:
Kees Cook <keescook@chromium.org> Reviewed-by:
-
Ricardo Ribalda authored
Logitech B910 and C910 firmware are unable to recover from a USB autosuspend. When it resumes, the device is in a state where it only produces invalid frames. Eg: $ echo 0xFFFF > /sys/module/uvcvideo/parameters/trace # enable verbose log $ yavta -c1 -n1 --file='frame#.jpg' --format MJPEG --size=1920x1080 /dev/video1 [350438.435219] uvcvideo: uvc_v4l2_open [350438.529794] uvcvideo: Resuming interface 2 [350438.529801] uvcvideo: Resuming interface 3 [350438.529991] uvcvideo: Trying format 0x47504a4d (MJPG): 1920x1080. [350438.529996] uvcvideo: Using default frame interval 33333.3 us (30.0 fps). [350438.551496] uvcvideo: uvc_v4l2_mmap [350438.555890] uvcvideo: Device requested 3060 B/frame bandwidth. [350438.555896] uvcvideo: Selecting alternate setting 11 (3060 B/frame bandwidth). [350438.556362] uvcvideo: Allocated 5 URB buffers of 32x3060 bytes each. [350439.316468] uvcvideo: Marking buffer as bad (error bit set). [350439.316475] uvcvideo: Frame complete (EOF found). [350439.316477] uvcvideo: EOF in empty payload. [350439.316484] uvcvideo: frame 1 stats: 149/261/417 packets, 1/149/417 pts (early initial), 416/417 scr, last pts/stc/sof 2976325734/2978107243/249 [350439.384510] uvcvideo: Marking buffer as bad (error bit set). [350439.384516] uvcvideo: Frame complete (EOF found). [350439.384518] uvcvideo: EOF in empty payload. [350439.384525] uvcvideo: frame 2 stats: 265/379/533 packets, 1/265/533 pts (early initial), 532/533 scr, last pts/stc/sof 2979524454/2981305193/316 [350439.448472] uvcvideo: Marking buffer as bad (error bit set). [350439.448478] uvcvideo: Frame complete (EOF found). [350439.448480] uvcvideo: EOF in empty payload. [350439.448487] uvcvideo: frame 3 stats: 265/377/533 packets, 1/265/533 pts (early initial), 532/533 scr, last pts/stc/sof 2982723174/2984503144/382 ...(loop)... The devices can leave this invalid state if the alternate setting of the streaming interface is toggled. This patch adds a quirk for this device so it can be autosuspended properly. lsusb -v: Bus 001 Device 049: ID 046d:0821 Logitech, Inc. HD Webcam C910 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 239 Miscellaneous Device bDeviceSubClass 2 bDeviceProtocol 1 Interface Association bMaxPacketSize0 64 idVendor 0x046d Logitech, Inc. idProduct 0x0821 HD Webcam C910 bcdDevice 0.10 iManufacturer 0 iProduct 0 iSerial 1 390022B0 bNumConfigurations 1 Signed-off-by:
Ricardo Ribalda <ribalda@chromium.org> Reviewed-by:
-
Ricardo Ribalda authored
usb_kill_urb warranties that all the handlers are finished when it returns, but does not protect against threads that might be handling asynchronously the urb. For UVC, the function uvc_ctrl_status_event_async() takes care of control changes asynchronously. If the code is executed in the following order: CPU 0 CPU 1 ===== ===== uvc_status_complete() uvc_status_stop() uvc_ctrl_status_event_work() uvc_status_start() -> FAIL Then uvc_status_start will keep failing and this error will be shown: <4>[ 5.540139] URB 0000000000000000 submitted while active drivers/usb/core/urb.c:378 usb_submit_urb+0x4c3/0x528 Let's improve the current situation, by not re-submiting the urb if we are stopping the status event. Also process the queued work (if any) during stop. CPU 0 CPU 1 ===== ===== uvc_status_complete() uvc_status_stop() uvc_status_start() uvc_ctrl_status_event_work() -> FAIL Hopefully, with the usb layer protection this should be enough to cover all the cases. Cc: stable@vger.kernel.org Fixes: e5225c82 ("media: uvcvideo: Send a control event when a Control Change interrupt arrives") Reviewed-by:
Yunke Cao <yunkec@chromium.org> Signed-off-by:
-
Ricardo Ribalda authored
Instead of duplicating the menu info, use the one from the core. Also, do not use extra memory for 1:1 mappings. Suggested-by:
-
Ricardo Ribalda authored
The device does not implement the power line frequenyc control correctly. It is a UVC 1.5 device, but implements the control as a UVC 1.1 device. Add the corresponding control mapping override. Bus 003 Device 002: ID 30c9:0093 Lenovo Integrated Camera Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.01 bDeviceClass 239 Miscellaneous Device bDeviceSubClass 2 bDeviceProtocol 1 Interface Association bMaxPacketSize0 64 idVendor 0x30c9 idProduct 0x0093 bcdDevice 0.07 iManufacturer 3 Lenovo iProduct 1 Integrated Camera iSerial 2 8SSC21J75356V1SR2830069 bNumConfigurations 1 Signed-off-by:
-
Ricardo Ribalda authored
Move the control mapping to uvc_ctrl.c. This way we do not have references to UVC controls or V4L2 controls in uvc_driver.c. This also fixes a bug introduced in commit 38207560 ("media: uvcvideo: Limit power line control for Quanta UVC Webcam"). The offending commit caused the power line control menu entries to have incorrect indices compared to the V4L2_CID_POWER_LINE_FREQUENCY_* enumeration. Now that the limited mapping reuses the correct menu_info array, the indices correctly map to the V4L2 control specification. Fixes: 38207560 ("media: uvcvideo: Limit power line control for Quanta UVC Webcam") Signed-off-by:
-
Ricardo Ribalda authored
Convert the array of structs into an array of pointers, that way the mappings can be reused. Signed-off-by:
-
Ricardo Ribalda authored
Replace the count with a mask field that lets us choose not only the max value, but also the minimum value and what values are valid in between. Suggested-by:
-
Ricardo Ribalda authored
Make an explicit reference to UVC 1.5, explaining how the algorithm supports the different behaviour of UVC 1.1 and 1.5. Reviewed-by:
HungNien Chen <hn.chen@sunplusit.com> Signed-off-by:
-
Ricardo Ribalda authored
The device does not implement the power line control correctly. Add a corresponding control mapping override. Bus 003 Device 002: ID 5986:1180 Acer, Inc EasyCamera Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 239 Miscellaneous Device bDeviceSubClass 2 bDeviceProtocol 1 Interface Association bMaxPacketSize0 64 idVendor 0x5986 Acer, Inc idProduct 0x1180 bcdDevice 56.04 iManufacturer 3 Bison iProduct 1 EasyCamera iSerial 2 bNumConfigurations 1 Reviewed-by:
Sergey Senozhatsky <senozhatsky@chromium.org> Reviewed-by:
-
