- 17 Feb, 2012 3 commits
-
-
Amit Beka authored
The testmode command for host command send now replies with a nl80211 message and the response it recieved from the device. This does not change the API directly, but adds a reply to the testmode call. Signed-off-by: Amit Beka <amit.beka@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Amit Beka authored
Replaced the old SRAM and periphery indirect access functions with a unified indirect memory access functions. These include new IWL_TM_CMDs for buffer read/write/dump which replace the SRAM read/dump commands, but the API for IWL_TM_CMD_INDIRECT_REG read/write will now not be supported (returns error). This also handles writing to periphery registers in 1-3 bytes. Requires the corresponding patch in the library for the API change. Signed-off-by: Amit Beka <amit.beka@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Wey-Yi Guy authored
A lot of error conditions in testmode log as IWL_DEBUG_INFO which is not logged by default. Change it Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
- 15 Feb, 2012 18 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirelessJohn W. Linville authored
Conflicts: net/mac80211/debugfs_sta.c net/mac80211/sta_info.h
-
Pavel Roskin authored
Rate control algorithms are supposed to stop processing when they encounter a rate with the index -1. Checking for rate->count not being zero is not enough. Allowing a rate with negative index leads to memory corruption in ath_debug_stat_rc(). One consequence of the bug is discussed at https://bugzilla.redhat.com/show_bug.cgi?id=768639Signed-off-by: Pavel Roskin <proski@gnu.org> Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Amitkumar Karwar authored
Driver maintains different flags for WEP, WPA, WPA2 security modes. Appropriate flag is set using security information provided in connect request. mwifiex_is_network_compatible() routine uses them to check if driver's setting is compatible with AP. Association is aborted if the routine fails. For some corner cases, it is observed that association is failed even for valid security information based on association history. This patch fixes the problem by clearing previous security setting during each association. We should set WEP key provided in connect request as default tx key. This missing change is also added here. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Most rate control implementations assume .get_rate and .tx_status are only called once the per-station data has been fully initialized. minstrel_ht crashes if this assumption is violated. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Tested-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
There are situations where we don't have the necessary rate control information yet for station entries, e.g. when associating. This currently doesn't really happen due to the dummy station handling; explicitly disabling rate control when it's not initialised will allow us to remove dummy stations. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Ulisses Furquim authored
We need to use the _sync() version for cancelling the info and security timer in the L2CAP connection delete path. Otherwise the delayed work handler might run after the connection object is freed. Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Ulisses Furquim authored
__cancel_delayed_work() is being used in some paths where we cannot sleep waiting for the delayed work to finish. However, that function might return while the timer is running and the work will be queued again. Replace the calls with safer cancel_delayed_work() version which spins until the timer handler finishes on other CPUs and cancels the delayed work. Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Manoj Iyer authored
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a5c ProdID=21f3 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=74DE2B344A7B C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Tested-by: Dennis Chua <dennis.chua@canonical.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Johan Hedberg authored
We should only perform a reset in hci_dev_do_close if the HCI_QUIRK_NO_RESET flag is set (since in such a case a reset will not be performed when initializing the device). Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
-
Octavian Purdila authored
There is an imbalance in the rfcomm_session_hold / rfcomm_session_put operations which causes the following crash: [ 685.010159] BUG: unable to handle kernel paging request at 6b6b6b6b [ 685.010169] IP: [<c149d76d>] rfcomm_process_dlcs+0x1b/0x15e [ 685.010181] *pdpt = 000000002d665001 *pde = 0000000000000000 [ 685.010191] Oops: 0000 [#1] PREEMPT SMP [ 685.010247] [ 685.010255] Pid: 947, comm: krfcommd Tainted: G C 3.0.16-mid8-dirty #44 [ 685.010266] EIP: 0060:[<c149d76d>] EFLAGS: 00010246 CPU: 1 [ 685.010274] EIP is at rfcomm_process_dlcs+0x1b/0x15e [ 685.010281] EAX: e79f551c EBX: 6b6b6b6b ECX: 00000007 EDX: e79f40b4 [ 685.010288] ESI: e79f4060 EDI: ed4e1f70 EBP: ed4e1f68 ESP: ed4e1f50 [ 685.010295] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 [ 685.010303] Process krfcommd (pid: 947, ti=ed4e0000 task=ed43e5e0 task.ti=ed4e0000) [ 685.010308] Stack: [ 685.010312] ed4e1f68 c149eb53 e5925150 e79f4060 ed500000 ed4e1f70 ed4e1f80 c149ec10 [ 685.010331] 00000000 ed43e5e0 00000000 ed4e1f90 ed4e1f9c c149ec87 0000bf54 00000000 [ 685.010348] 00000000 ee03bf54 c149ec37 ed4e1fe4 c104fe01 00000000 00000000 00000000 [ 685.010367] Call Trace: [ 685.010376] [<c149eb53>] ? rfcomm_process_rx+0x6e/0x74 [ 685.010387] [<c149ec10>] rfcomm_process_sessions+0xb7/0xde [ 685.010398] [<c149ec87>] rfcomm_run+0x50/0x6d [ 685.010409] [<c149ec37>] ? rfcomm_process_sessions+0xde/0xde [ 685.010419] [<c104fe01>] kthread+0x63/0x68 [ 685.010431] [<c104fd9e>] ? __init_kthread_worker+0x42/0x42 [ 685.010442] [<c14dae82>] kernel_thread_helper+0x6/0xd This issue has been brought up earlier here: https://lkml.org/lkml/2011/5/21/127 The issue appears to be the rfcomm_session_put in rfcomm_recv_ua. This operation doesn't seem be to required as for the non-initiator case we have the rfcomm_process_rx doing an explicit put and in the initiator case the last dlc_unlink will drive the reference counter to 0. There have been several attempts to fix these issue: 6c2718da Bluetooth: Do not call rfcomm_session_put() for RFCOMM UA on closed socket 683d949a Bluetooth: Never deallocate a session when some DLC points to it but AFAICS they do not fix the issue just make it harder to reproduce. Signed-off-by: Octavian Purdila <octavian.purdila@intel.com> Signed-off-by: Gopala Krishna Murala <gopala.krishna.murala@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Andre Guedes authored
We don't need to use the _sync variant in hci_conn_hold and hci_conn_put to cancel conn->disc_work delayed work. This way we avoid potential deadlocks like this one reported by lockdep. ====================================================== [ INFO: possible circular locking dependency detected ] 3.2.0+ #1 Not tainted ------------------------------------------------------- kworker/u:1/17 is trying to acquire lock: (&hdev->lock){+.+.+.}, at: [<ffffffffa0041155>] hci_conn_timeout+0x62/0x158 [bluetooth] but task is already holding lock: ((&(&conn->disc_work)->work)){+.+...}, at: [<ffffffff81035751>] process_one_work+0x11a/0x2bf which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 ((&(&conn->disc_work)->work)){+.+...}: [<ffffffff81057444>] lock_acquire+0x8a/0xa7 [<ffffffff81034ed1>] wait_on_work+0x3d/0xaa [<ffffffff81035b54>] __cancel_work_timer+0xac/0xef [<ffffffff81035ba4>] cancel_delayed_work_sync+0xd/0xf [<ffffffffa00554b0>] smp_chan_create+0xde/0xe6 [bluetooth] [<ffffffffa0056160>] smp_conn_security+0xa3/0x12d [bluetooth] [<ffffffffa0053640>] l2cap_connect_cfm+0x237/0x2e8 [bluetooth] [<ffffffffa004239c>] hci_proto_connect_cfm+0x2d/0x6f [bluetooth] [<ffffffffa0046ea5>] hci_event_packet+0x29d1/0x2d60 [bluetooth] [<ffffffffa003dde3>] hci_rx_work+0xd0/0x2e1 [bluetooth] [<ffffffff810357af>] process_one_work+0x178/0x2bf [<ffffffff81036178>] worker_thread+0xce/0x152 [<ffffffff81039a03>] kthread+0x95/0x9d [<ffffffff812e7754>] kernel_thread_helper+0x4/0x10 -> #1 (slock-AF_BLUETOOTH-BTPROTO_L2CAP){+.+...}: [<ffffffff81057444>] lock_acquire+0x8a/0xa7 [<ffffffff812e553a>] _raw_spin_lock_bh+0x36/0x6a [<ffffffff81244d56>] lock_sock_nested+0x24/0x7f [<ffffffffa004d96f>] lock_sock+0xb/0xd [bluetooth] [<ffffffffa0052906>] l2cap_chan_connect+0xa9/0x26f [bluetooth] [<ffffffffa00545f8>] l2cap_sock_connect+0xb3/0xff [bluetooth] [<ffffffff81243b48>] sys_connect+0x69/0x8a [<ffffffff812e6579>] system_call_fastpath+0x16/0x1b -> #0 (&hdev->lock){+.+.+.}: [<ffffffff81056d06>] __lock_acquire+0xa80/0xd74 [<ffffffff81057444>] lock_acquire+0x8a/0xa7 [<ffffffff812e3870>] __mutex_lock_common+0x48/0x38e [<ffffffff812e3c75>] mutex_lock_nested+0x2a/0x31 [<ffffffffa0041155>] hci_conn_timeout+0x62/0x158 [bluetooth] [<ffffffff810357af>] process_one_work+0x178/0x2bf [<ffffffff81036178>] worker_thread+0xce/0x152 [<ffffffff81039a03>] kthread+0x95/0x9d [<ffffffff812e7754>] kernel_thread_helper+0x4/0x10 other info that might help us debug this: Chain exists of: &hdev->lock --> slock-AF_BLUETOOTH-BTPROTO_L2CAP --> (&(&conn->disc_work)->work) Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock((&(&conn->disc_work)->work)); lock(slock-AF_BLUETOOTH-BTPROTO_L2CAP); lock((&(&conn->disc_work)->work)); lock(&hdev->lock); *** DEADLOCK *** 2 locks held by kworker/u:1/17: #0: (hdev->name){.+.+.+}, at: [<ffffffff81035751>] process_one_work+0x11a/0x2bf #1: ((&(&conn->disc_work)->work)){+.+...}, at: [<ffffffff81035751>] process_one_work+0x11a/0x2bf stack backtrace: Pid: 17, comm: kworker/u:1 Not tainted 3.2.0+ #1 Call Trace: [<ffffffff812e06c6>] print_circular_bug+0x1f8/0x209 [<ffffffff81056d06>] __lock_acquire+0xa80/0xd74 [<ffffffff81021ef2>] ? arch_local_irq_restore+0x6/0xd [<ffffffff81022bc7>] ? vprintk+0x3f9/0x41e [<ffffffff81057444>] lock_acquire+0x8a/0xa7 [<ffffffffa0041155>] ? hci_conn_timeout+0x62/0x158 [bluetooth] [<ffffffff812e3870>] __mutex_lock_common+0x48/0x38e [<ffffffffa0041155>] ? hci_conn_timeout+0x62/0x158 [bluetooth] [<ffffffff81190fd6>] ? __dynamic_pr_debug+0x6d/0x6f [<ffffffffa0041155>] ? hci_conn_timeout+0x62/0x158 [bluetooth] [<ffffffff8105320f>] ? trace_hardirqs_off+0xd/0xf [<ffffffff812e3c75>] mutex_lock_nested+0x2a/0x31 [<ffffffffa0041155>] hci_conn_timeout+0x62/0x158 [bluetooth] [<ffffffff810357af>] process_one_work+0x178/0x2bf [<ffffffff81035751>] ? process_one_work+0x11a/0x2bf [<ffffffff81055af3>] ? lock_acquired+0x1d0/0x1df [<ffffffffa00410f3>] ? hci_acl_disconn+0x65/0x65 [bluetooth] [<ffffffff81036178>] worker_thread+0xce/0x152 [<ffffffff810407ed>] ? finish_task_switch+0x45/0xc5 [<ffffffff810360aa>] ? manage_workers.isra.25+0x16a/0x16a [<ffffffff81039a03>] kthread+0x95/0x9d [<ffffffff812e7754>] kernel_thread_helper+0x4/0x10 [<ffffffff812e5db4>] ? retint_restore_args+0x13/0x13 [<ffffffff8103996e>] ? __init_kthread_worker+0x55/0x55 [<ffffffff812e7750>] ? gs_change+0x13/0x13 Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Octavian Purdila authored
Since bluetooth uses multiple protocols types, to avoid lockdep warnings, we need to use different lockdep classes (one for each protocol type). This is already done in bt_sock_create but it misses a couple of cases when new connections are created. This patch corrects that to fix the following warning: <4>[ 1864.732366] ======================================================= <4>[ 1864.733030] [ INFO: possible circular locking dependency detected ] <4>[ 1864.733544] 3.0.16-mid3-00007-gc9a0f62 #3 <4>[ 1864.733883] ------------------------------------------------------- <4>[ 1864.734408] t.android.btclc/4204 is trying to acquire lock: <4>[ 1864.734869] (rfcomm_mutex){+.+.+.}, at: [<c14970ea>] rfcomm_dlc_close+0x15/0x30 <4>[ 1864.735541] <4>[ 1864.735549] but task is already holding lock: <4>[ 1864.736045] (sk_lock-AF_BLUETOOTH){+.+.+.}, at: [<c1498bf7>] lock_sock+0xa/0xc <4>[ 1864.736732] <4>[ 1864.736740] which lock already depends on the new lock. <4>[ 1864.736750] <4>[ 1864.737428] <4>[ 1864.737437] the existing dependency chain (in reverse order) is: <4>[ 1864.738016] <4>[ 1864.738023] -> #1 (sk_lock-AF_BLUETOOTH){+.+.+.}: <4>[ 1864.738549] [<c1062273>] lock_acquire+0x104/0x140 <4>[ 1864.738977] [<c13d35c1>] lock_sock_nested+0x58/0x68 <4>[ 1864.739411] [<c1493c33>] l2cap_sock_sendmsg+0x3e/0x76 <4>[ 1864.739858] [<c13d06c3>] __sock_sendmsg+0x50/0x59 <4>[ 1864.740279] [<c13d0ea2>] sock_sendmsg+0x94/0xa8 <4>[ 1864.740687] [<c13d0ede>] kernel_sendmsg+0x28/0x37 <4>[ 1864.741106] [<c14969ca>] rfcomm_send_frame+0x30/0x38 <4>[ 1864.741542] [<c1496a2a>] rfcomm_send_ua+0x58/0x5a <4>[ 1864.741959] [<c1498447>] rfcomm_run+0x441/0xb52 <4>[ 1864.742365] [<c104f095>] kthread+0x63/0x68 <4>[ 1864.742742] [<c14d5182>] kernel_thread_helper+0x6/0xd <4>[ 1864.743187] <4>[ 1864.743193] -> #0 (rfcomm_mutex){+.+.+.}: <4>[ 1864.743667] [<c1061ada>] __lock_acquire+0x988/0xc00 <4>[ 1864.744100] [<c1062273>] lock_acquire+0x104/0x140 <4>[ 1864.744519] [<c14d2c70>] __mutex_lock_common+0x3b/0x33f <4>[ 1864.744975] [<c14d303e>] mutex_lock_nested+0x2d/0x36 <4>[ 1864.745412] [<c14970ea>] rfcomm_dlc_close+0x15/0x30 <4>[ 1864.745842] [<c14990d9>] __rfcomm_sock_close+0x5f/0x6b <4>[ 1864.746288] [<c1499114>] rfcomm_sock_shutdown+0x2f/0x62 <4>[ 1864.746737] [<c13d275d>] sys_socketcall+0x1db/0x422 <4>[ 1864.747165] [<c14d42f0>] syscall_call+0x7/0xb Signed-off-by: Octavian Purdila <octavian.purdila@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Vinicius Costa Gomes authored
queue_delayed_work() expects a relative time for when that work should be scheduled. Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Andrzej Kaczmarek authored
After moving L2CAP timers to workqueues l2cap_set_timer expects timeout value to be specified in jiffies but constants defined in miliseconds are used. This makes timeouts unreliable when CONFIG_HZ is not set to 1000. __set_chan_timer macro still uses jiffies as input to avoid multiple conversions from/to jiffies for sk_sndtimeo value which is already specified in jiffies. Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Ackec-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Andrzej Kaczmarek authored
sk_sndtime value should be specified in jiffies thus initial value needs to be converted from miliseconds. Otherwise this timeout is unreliable when CONFIG_HZ is not set to 1000. Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Johan Hedberg authored
As reported by Dan Carpenter this function causes a Sparse warning and shouldn't be declared inline: include/net/bluetooth/l2cap.h:837:30 error: marked inline, but without a definition" Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
-
Daniel Wagner authored
[ 2096.384084] btusb_send_frame:684: hci0 [ 2096.384087] usb 3-1: BOGUS urb flags, 2 --> 0 [ 2096.384091] Bluetooth: hci0 urb ffff8801b61d3a80 submission failed (22) According the documentation in usb_submit_urb() URB_ISO_ASAP flag is only allowed for endpoints of type USB_ENDPOINT_XFER_ISOC. This reverts commit b8aabfc9. Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de> Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
Peter Hurley authored
Commit 33060542 fixed l2cap conn establishment for non-ssp remote devices by not setting HCI_CONN_ENCRYPT_PEND every time conn security is tested (which was always returning failure on any subsequent security checks). However, this broke l2cap conn establishment for ssp remote devices when an ACL link was already established at SDP-level security. This fix ensures that encryption must be pending whenever authentication is also pending. Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Tested-by: Daniel Wagner <daniel.wagner@bmw-carit.de> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
-
- 09 Feb, 2012 3 commits
-
-
Simon Graham authored
Fixes problem where caller would think routine succeeded when it failed leading to divide by zero panic. Signed-off-by: Simon Graham <simon.graham@virtualcomputer.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
read_lock(&tpt_trig->trig.leddev_list_lock) is accessed via the path ieee80211_open (->) ieee80211_do_open (->) ieee80211_mod_tpt_led_trig (->) ieee80211_start_tpt_led_trig (->) tpt_trig_timer before initializing it. the intilization of this read/write lock happens via the path ieee80211_led_init (->) led_trigger_register, but we are doing 'ieee80211_led_init' after 'ieeee80211_if_add' where we register netdev_ops. so we access leddev_list_lock before initializing it and causes the following bug in chrome laptops with AR928X cards with the following script while true do sudo modprobe -v ath9k sleep 3 sudo modprobe -r ath9k sleep 3 done BUG: rwlock bad magic on CPU#1, wpa_supplicant/358, f5b9eccc Pid: 358, comm: wpa_supplicant Not tainted 3.0.13 #1 Call Trace: [<8137b9df>] rwlock_bug+0x3d/0x47 [<81179830>] do_raw_read_lock+0x19/0x29 [<8137f063>] _raw_read_lock+0xd/0xf [<f9081957>] tpt_trig_timer+0xc3/0x145 [mac80211] [<f9081f3a>] ieee80211_mod_tpt_led_trig+0x152/0x174 [mac80211] [<f9076a3f>] ieee80211_do_open+0x11e/0x42e [mac80211] [<f9075390>] ? ieee80211_check_concurrent_iface+0x26/0x13c [mac80211] [<f9076d97>] ieee80211_open+0x48/0x4c [mac80211] [<812dbed8>] __dev_open+0x82/0xab [<812dc0c9>] __dev_change_flags+0x9c/0x113 [<812dc1ae>] dev_change_flags+0x18/0x44 [<8132144f>] devinet_ioctl+0x243/0x51a [<81321ba9>] inet_ioctl+0x93/0xac [<812cc951>] sock_ioctl+0x1c6/0x1ea [<812cc78b>] ? might_fault+0x20/0x20 [<810b1ebb>] do_vfs_ioctl+0x46e/0x4a2 [<810a6ebb>] ? fget_light+0x2f/0x70 [<812ce549>] ? sys_recvmsg+0x3e/0x48 [<810b1f35>] sys_ioctl+0x46/0x69 [<8137fa77>] sysenter_do_call+0x12/0x2 Cc: <stable@vger.kernel.org> Cc: Gary Morain <gmorain@google.com> Cc: Paul Stewart <pstew@google.com> Cc: Abhijit Pradhan <abhijit@qca.qualcomm.com> Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Acked-by: Johannes Berg <johannes.berg@intel.com> Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
Fixes problem where caller would think routine succeeded when it failed leading to divide by zero panic. (This also reverts an earlier attempt, commit 42bc0c97 "rtlwifi: Return correct failure code on error". -- JWL) Signed-off-by: Simon Graham <simon.graham@virtualcomputer.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 08 Feb, 2012 14 commits
-
-
Felix Fietkau authored
Most rate control implementations assume .get_rate and .tx_status are only called once the per-station data has been fully initialized. minstrel_ht crashes if this assumption is violated. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Tested-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Simon Graham authored
Callers of rtl_pci_init expect zero to be returned on error. Returning the error code leads to, amongst other things, divide by zero panics attempting to use the ring size that is set to zero. Signed-off-by: Simon Graham <simon.graham@virtualcomputer.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luis R. Rodriguez authored
If you want to use mesh support from mac80211 on a recent kernel on 2.6.24 you'll run into a name clash when compiling against include/linux/namei.h, so rename this routine. /home/mcgrof/tmp/compat-wireless-3.2.5-1/net/mac80211/mesh_pathtbl.c: At top level: /home/mcgrof/tmp/compat-wireless-3.2.5-1/net/mac80211/mesh_pathtbl.c:342:26: error: conflicting types for ‘path_lookup’ include/linux/namei.h:71:12: note: previous declaration of ‘path_lookup’ was here Although this could sit as a separate patch in compat-wireless it seems best to just merge upstream. Cc: Javier Cardona <javier@cozybit.com> Signed-off-by: Luis R. Rodriguez <mcgrof@frijolero.org> Acked-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Simon Graham authored
Handle previous allocation failures when freeing device memory Signed-off-by: Simon Graham <simon.graham@virtualcomputer.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
When not debugging mac80211 code, station state transitions do not need to show up in the kernel log. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gertjan van Wingerde authored
Align with the v2.5.0.0 Ralink RT3572 driver. Save the EEPROM txmixer_gain values inside the rt2800 driver data structure and use it throughout the code. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gertjan van Wingerde authored
Align with the v2.5.0.0 Ralink RT3572 driver. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gertjan van Wingerde authored
Align with the v2.5.0.0 Ralink RT3572 driver. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gertjan van Wingerde authored
Align with v2.5.0.0 Ralink RT3572 driver for 2.4GHz band channel switch. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gertjan van Wingerde authored
This brings the rt2800 channel switching code for RT3572 closer to the v2.5.0.0 Ralink RT3572 driver. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gertjan van Wingerde authored
The comment states that the field is only used for rt61pci and rt73usb. However, it is now used by rt2800pci and rt2800usb as well, so the comment is not correct anymore. Update the comment to not state any low-level drivers anymore. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gertjan van Wingerde authored
Start using the struct rt2x00_dev driver data in rt2800 for the calibration data. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Gertjan van Wingerde authored
We are getting more and more fields in struct rt2x00_dev that are specific to one or two of the low-level drivers. Instead of putting these fields inside the main structure and thus clobbering all low-level drivers with these fields, introduce the concept of driver data inside struct rt2x00_dev, whose size is indicated by the low-level driver and which can be populated by the low-level driver. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
David Gibson authored
The two orinoco mailing lists on sourceforge were set up many years ago and are now more or less moribund. I'd like to shut them down, so I don't have to keep filtering the spam from them (which is most of what comes through now). In preparation, this patch removes the reference to them from the MAINTAINERS file. Any remaining discussion of this approaching obsolete driver can go to the linux-wireless list. Signed-off-by: David Gibson <hermes@gibson.dropbear.id.au> Acked-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 07 Feb, 2012 1 commit
-
-
Tomas Vanek authored
Some devices (iwl5100) cannot connect to zd1211rw based AP. It appears that zd1211 firmware messes up duration_id field if it is not set to zero by driver. Sniffing traffic shows that zd1211 is transmitting frames with duration_id bits 14 and 15 set and other bits appearing random. Setting duration_id at driver to zero results zd1211 outputting sane duration_id. This means that firmware is setting correct values itself and expects duration_id to be zero in first place. Looking at vendor driver shows that only PSPoll frames have duration_id set by driver, for other frames duration_id left zero. Original bug-report and attached patch at: http://sourceforge.net/mailarchive/message.php?msg_id=28759111Reported-by: Tomas Vanek <Tomas.Vanek@fbl.cz> [modified original patch from bug-report, added check for pspoll frame] Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 06 Feb, 2012 1 commit
-
-
Johannes Berg authored
There are situations where we don't have the necessary rate control information yet for station entries, e.g. when associating. This currently doesn't really happen due to the dummy station handling; explicitly disabling rate control when it's not initialised will allow us to remove dummy stations. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-