- 10 Oct, 2023 1 commit
-
-
Ilya Leoshkevich authored
One of the first things that s390x kernel functions do is storing the the caller's frame address (backchain) on stack. This makes unwinding possible. The backchain is always stored at frame offset 152, which is inside the 160-byte stack area, that the functions allocate for their callees. The callees must preserve the backchain; the remaining 152 bytes they may use as they please. Currently the trampoline uses all 160 bytes, clobbering the backchain. This causes kernel panics when using __builtin_return_address() in functions called by the trampoline. Fix by reducing the usage of the caller-reserved stack area by 8 bytes in the trampoline. Fixes: 528eb2cb ("s390/bpf: Implement arch_prepare_bpf_trampoline()") Reported-by:
Song Liu <song@kernel.org> Signed-off-by:
Ilya Leoshkevich <iii@linux.ibm.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20231010203512.385819-2-iii@linux.ibm.com
-
- 09 Oct, 2023 5 commits
-
-
David Vernet authored
A previous commit updated the verifier to print an accurate failure message for when someone specifies a nonzero return value from an async callback. This adds a testcase for validating that the verifier emits the correct message in such a case. Signed-off-by:
David Vernet <void@manifault.com> Signed-off-by:
-
David Vernet authored
The verifier, as part of check_return_code(), verifies that async callbacks such as from e.g. timers, will return 0. It does this by correctly checking that R0->var_off is in tnum_const(0), which effectively checks that it's in a range of 0. If this condition fails, however, it prints an error message which says that the value should have been in (0x0; 0x1). This results in possibly confusing output such as the following in which an async callback returns 1: At async callback the register R0 has value (0x1; 0x0) should have been in (0x0; 0x1) The fix is easy -- we should just pass the tnum_const(0) as the correct range to verbose_invalid_scalar(), which will then print the following: At async callback the register R0 has value (0x1; 0x0) should have been in (0x0; 0x0) Fixes: bfc6bb74 ("bpf: Implement verifier support for validation of async callbacks.") Signed-off-by:
-
Andrew Kanner authored
Syzkaller reported the following issue: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 2807 at mm/vmalloc.c:3247 __vmalloc_node_range (mm/vmalloc.c:3361) Modules linked in: CPU: 0 PID: 2807 Comm: repro Not tainted 6.6.0-rc2+ #12 Hardware name: Generic DT based system unwind_backtrace from show_stack (arch/arm/kernel/traps.c:258) show_stack from dump_stack_lvl (lib/dump_stack.c:107 (discriminator 1)) dump_stack_lvl from __warn (kernel/panic.c:633 kernel/panic.c:680) __warn from warn_slowpath_fmt (./include/linux/context_tracking.h:153 kernel/panic.c:700) warn_slowpath_fmt from __vmalloc_node_range (mm/vmalloc.c:3361 (discriminator 3)) __vmalloc_node_range from vmalloc_user (mm/vmalloc.c:3478) vmalloc_user from xskq_create (net/xdp/xsk_queue.c:40) xskq_create from xsk_setsockopt (net/xdp/xsk.c:953 net/xdp/xsk.c:1286) xsk_setsockopt from __sys_setsockopt (net/socket.c:2308) __sys_setsockopt from ret_fast_syscall (arch/arm/kernel/entry-common.S:68) xskq_get_ring_size() uses struct_size() macro to safely calculate the size of struct xsk_queue and q->nentries of desc members. But the syzkaller repro was able to set q->nentries with the value initially taken from copy_from_sockptr() high enough to return SIZE_MAX by struct_size(). The next PAGE_ALIGN(size) is such case will overflow the size_t value and set it to 0. This will trigger WARN_ON_ONCE in vmalloc_user() -> __vmalloc_node_range(). The issue is reproducible on 32-bit arm kernel. Fixes: 9f78bf33 ("xsk: support use vaddr as ring") Reported-by: syzbot+fae676d3cf469331fc89@syzkaller.appspotmail.com Closes: https://lore.kernel.org/all/000000000000c84b4705fb31741e@google.com/T/ Reported-by: syzbot+b132693e925cbbd89e26@syzkaller.appspotmail.com Closes: https://lore.kernel.org/all/000000000000e20df20606ebab4f@google.com/T/Signed-off-by:
Andrew Kanner <andrew.kanner@gmail.com> Signed-off-by:
Magnus Karlsson <magnus.karlsson@intel.com> Link: https://syzkaller.appspot.com/bug?extid=fae676d3cf469331fc89 Link: https://lore.kernel.org/bpf/20231007075148.1759-1-andrew.kanner@gmail.com
-
Björn Töpel authored
The RISC-V BPF uses a5 for BPF return values, which are zero-extended, whereas the RISC-V ABI uses a0 which is sign-extended. In other words, a5 and a0 can differ, and are used in different context. The BPF trampoline are used for both BPF programs, and regular kernel functions. Make sure that the RISC-V BPF trampoline saves, and restores both a0 and a5. Fixes: 49b5e77a ("riscv, bpf: Add bpf trampoline support for RV64") Signed-off-by:
Björn Töpel <bjorn@rivosinc.com> Signed-off-by:
-
Björn Töpel authored
The RISC-V architecture does not expose sub-registers, and hold all 32-bit values in a sign-extended format [1] [2]: | The compiler and calling convention maintain an invariant that all | 32-bit values are held in a sign-extended format in 64-bit | registers. Even 32-bit unsigned integers extend bit 31 into bits | 63 through 32. Consequently, conversion between unsigned and | signed 32-bit integers is a no-op, as is conversion from a signed | 32-bit integer to a signed 64-bit integer. While BPF, on the other hand, exposes sub-registers, and use zero-extension (similar to arm64/x86). This has led to some subtle bugs, where a BPF JITted program has not sign-extended the a0 register (return value in RISC-V land), passed the return value up the kernel, e.g.: | int from_bpf(void); | | long foo(void) | { | return from_bpf(); | } Here, a0 would be 0xffff_ffff, instead of the expected 0xffff_ffff_ffff_ffff. Internally, the RISC-V JIT uses a5 as a dedicated register for BPF return values. Keep a5 zero-extended, but explicitly sign-extend a0 (which is used outside BPF land). Now that a0 (RISC-V ABI) and a5 (BPF ABI) differs, a0 is only moved to a5 for non-BPF native calls (BPF_PSEUDO_CALL). Fixes: 2353ecc6 ("bpf, riscv: add BPF JIT for RV64G") Signed-off-by:
-
- 07 Oct, 2023 7 commits
-
-
Daniel Borkmann authored
Martin reported that on his local dev machine the test_tc_chain_mixed() fails as "test_tc_chain_mixed:FAIL:seen_tc5 unexpected seen_tc5: actual 1 != expected 0" and others occasionally, too. However, when running in a more isolated setup (qemu in particular), it works fine for him. The reason is that there is a small race-window where seen_tc* could turn into true for various test cases when there is background traffic, e.g. after the asserts they often get reset. In such case when subsequent detach takes place, unrelated background traffic could have already flipped the bool to true beforehand. Add a small helper tc_skel_reset_all_seen() to reset all bools before we do the ping test. At this point, everything is set up as expected and therefore no race can occur. All tc_{opts,links} tests continue to pass after this change. Reported-by:Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by:
-
Daniel Borkmann authored
Add a new test case to query on an empty bpf_mprog and pass the revision directly into expected_revision for attachment to assert that this does succeed. ./test_progs -t tc_opts [ 1.406778] tsc: Refined TSC clocksource calibration: 3407.990 MHz [ 1.408863] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x311fcaf6eb0, max_idle_ns: 440795321766 ns [ 1.412419] clocksource: Switched to clocksource tsc [ 1.428671] bpf_testmod: loading out-of-tree module taints kernel. [ 1.430260] bpf_testmod: module verification failed: signature and/or required key missing - tainting kernel #252 tc_opts_after:OK #253 tc_opts_append:OK #254 tc_opts_basic:OK #255 tc_opts_before:OK #256 tc_opts_chain_classic:OK #257 tc_opts_chain_mixed:OK #258 tc_opts_delete_empty:OK #259 tc_opts_demixed:OK #260 tc_opts_detach:OK #261 tc_opts_detach_after:OK #262 tc_opts_detach_before:OK #263 tc_opts_dev_cleanup:OK #264 tc_opts_invalid:OK #265 tc_opts_max:OK #266 tc_opts_mixed:OK #267 tc_opts_prepend:OK #268 tc_opts_query:OK #269 tc_opts_query_attach:OK <--- (new test) #270 tc_opts_replace:OK #271 tc_opts_revision:OK Summary: 20/0 PASSED, 0 SKIPPED, 0 FAILED Signed-off-by:
-
Daniel Borkmann authored
Simplify __assert_mprog_count() to remove the -ENOENT corner case as the bpf_prog_query() now returns 0 when no bpf_mprog is attached. This also allows to convert a few test cases from using raw __assert_mprog_count() over to plain assert_mprog_count() helper. Signed-off-by:
-
Daniel Borkmann authored
Add a new test case which performs double query of the bpf_mprog through libbpf API, but also via raw bpf(2) syscall. This is testing to gather first the count and then in a subsequent probe the full information with the program array without clearing passed structs in between. # ./vmtest.sh -- ./test_progs -t tc_opts [...] ./test_progs -t tc_opts [ 1.398818] tsc: Refined TSC clocksource calibration: 3407.999 MHz [ 1.400263] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x311fd336761, max_idle_ns: 440795243819 ns [ 1.402734] clocksource: Switched to clocksource tsc [ 1.426639] bpf_testmod: loading out-of-tree module taints kernel. [ 1.428112] bpf_testmod: module verification failed: signature and/or required key missing - tainting kernel #252 tc_opts_after:OK #253 tc_opts_append:OK #254 tc_opts_basic:OK #255 tc_opts_before:OK #256 tc_opts_chain_classic:OK #257 tc_opts_chain_mixed:OK #258 tc_opts_delete_empty:OK #259 tc_opts_demixed:OK #260 tc_opts_detach:OK #261 tc_opts_detach_after:OK #262 tc_opts_detach_before:OK #263 tc_opts_dev_cleanup:OK #264 tc_opts_invalid:OK #265 tc_opts_max:OK #266 tc_opts_mixed:OK #267 tc_opts_prepend:OK #268 tc_opts_query:OK <--- (new test) #269 tc_opts_replace:OK #270 tc_opts_revision:OK Summary: 19/0 PASSED, 0 SKIPPED, 0 FAILED Signed-off-by:
-
Lorenz Bauer authored
The recently added tcx attachment extended the BPF UAPI for attaching and detaching by a couple of fields. Those fields are currently only supported for tcx, other types like cgroups and flow dissector silently ignore the new fields except for the new flags. This is problematic once we extend bpf_mprog to older attachment types, since it's hard to figure out whether the syscall really was successful if the kernel silently ignores non-zero values. Explicitly reject non-zero fields relevant to bpf_mprog for attachment types which don't use the latter yet. Fixes: e420bed0 ("bpf: Add fd-based tcx multi-prog infra with link support") Signed-off-by:
Lorenz Bauer <lmb@isovalent.com> Co-developed-by:
-
Daniel Borkmann authored
Improve consistency for bpf_mprog_query() API and let the latter also handle a NULL entry as can be the case for tcx. Instead of returning -ENOENT, we copy a count of 0 and revision of 1 to user space, so that this can be fed into a subsequent bpf_mprog_attach() call as expected_revision. A BPF self- test as part of this series has been added to assert this case. Suggested-by:
-
Daniel Borkmann authored
While working on the ebpf-go [0] library integration for bpf_mprog and tcx, Lorenz noticed that two subsequent BPF_PROG_QUERY requests currently fail. A typical workflow is to first gather the bpf_mprog count without passing program/ link arrays, followed by the second request which contains the actual array pointers. The initial call populates count and revision fields. The second call gets rejected due to a BPF_PROG_QUERY_LAST_FIELD bug which should point to query.revision instead of query.link_attach_flags since the former is really the last member. It was not noticed in libbpf as bpf_prog_query_opts() always calls bpf(2) with an on-stack bpf_attr that is memset() each time (and therefore query.revision was reset to zero). [0] https://ebpf-go.dev Fixes: e420bed0 ("bpf: Add fd-based tcx multi-prog infra with link support") Reported-by:
-
- 06 Oct, 2023 8 commits
-
-
Gustavo A. R. Silva authored
commit d61491a5 ("net/sched: cls_u32: Replace one-element array with flexible-array member") incorrecly replaced an instance of `sizeof(*tp_c)` with `struct_size(tp_c, hlist->ht, 1)`. This results in a an over-allocation of 8 bytes. This change is wrong because `hlist` in `struct tc_u_common` is a pointer: net/sched/cls_u32.c: struct tc_u_common { struct tc_u_hnode __rcu *hlist; void *ptr; int refcnt; struct idr handle_idr; struct hlist_node hnode; long knodes; }; So, the use of `struct_size()` makes no sense: we don't need to allocate any extra space for a flexible-array member. `sizeof(*tp_c)` is just fine. So, `struct_size(tp_c, hlist->ht, 1)` translates to: sizeof(*tp_c) + sizeof(tp_c->hlist->ht) == sizeof(struct tc_u_common) + sizeof(struct tc_u_knode *) == 144 + 8 == 0x98 (byes) ^^^ | unnecessary extra allocation size $ pahole -C tc_u_common net/sched/cls_u32.o struct tc_u_common { struct tc_u_hnode * hlist; /* 0 8 */ void * ptr; /* 8 8 */ int refcnt; /* 16 4 */ /* XXX 4 bytes hole, try to pack */ struct idr handle_idr; /* 24 96 */ /* --- cacheline 1 boundary (64 bytes) was 56 bytes ago --- */ struct hlist_node hnode; /* 120 16 */ /* --- cacheline 2 boundary (128 bytes) was 8 bytes ago --- */ long int knodes; /* 136 8 */ /* size: 144, cachelines: 3, members: 6 */ /* sum members: 140, holes: 1, sum holes: 4 */ /* last cacheline: 16 bytes */ }; And with `sizeof(*tp_c)`, we have: sizeof(*tp_c) == sizeof(struct tc_u_common) == 144 == 0x90 (bytes) which is the correct and original allocation size. Fix this issue by replacing `struct_size(tp_c, hlist->ht, 1)` with `sizeof(*tp_c)`, and avoid allocating 8 too many bytes. The following difference in binary output is expected and reflects the desired change: | net/sched/cls_u32.o | @@ -6148,7 +6148,7 @@ | include/linux/slab.h:599 | 2cf5: mov 0x0(%rip),%rdi # 2cfc <u32_init+0xfc> | 2cf8: R_X86_64_PC32 kmalloc_caches+0xc |- 2cfc: mov $0x98,%edx |+ 2cfc: mov $0x90,%edx Reported-by:
Alejandro Colomar <alx@kernel.org> Closes: https://lore.kernel.org/lkml/09b4a2ce-da74-3a19-6961-67883f634d98@kernel.org/Signed-off-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Acked-by:
Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Marek Behún says: ==================== net: dsa: qca8k: fix qca8k driver for Turris 1.x this is v2 of https://lore.kernel.org/netdev/20231002104612.21898-1-kabel@kernel.org/ Changes since v1: - fixed a typo in commit message noticed by Simon Horman ==================== Signed-off-by:
-
Marek Behún authored
Besides the QCA8337 switch the Turris 1.x device has on it's MDIO bus also Micron ethernet PHY (dedicated to the WAN port). We've been experiencing a strange behavior of the WAN ethernet interface, wherein the WAN PHY started timing out the MDIO accesses, for example when the interface was brought down and then back up. Bisecting led to commit 2cd54856 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet"), which added support to access the QCA8337 switch's internal PHYs via management ethernet frames. Connecting the MDIO bus pins onto an oscilloscope, I was able to see that the MDIO bus was active whenever a request to read/write an internal PHY register was done via an management ethernet frame. My theory is that when the switch core always communicates with the internal PHYs via the MDIO bus, even when externally we request the access via ethernet. This MDIO bus is the same one via which the switch and internal PHYs are accessible to the board, and the board may have other devices connected on this bus. An ASCII illustration may give more insight: +---------+ +----| | | | WAN PHY | | +--| | | | +---------+ | | | | +----------------------------------+ | | | QCA8337 | MDC | | | +-------+ | ------o-+--|--------o------------o--| | | MDIO | | | | | PHY 1 |-|--to RJ45 --------o--|---o----+---------o--+--| | | | | | | | +-------+ | | +-------------+ | o--| | | | | MDIO MDC | | | | PHY 2 |-|--to RJ45 eth1 | | | o--+--| | | -----------|-|port0 | | | +-------+ | | | | | o--| | | | | switch core | | | | PHY 3 |-|--to RJ45 | +-------------+ o--+--| | | | | | +-------+ | | | o--| ... | | +----------------------------------+ When we send a request to read an internal PHY register via an ethernet management frame via eth1, the switch core receives the ethernet frame on port 0 and then communicates with the internal PHY via MDIO. At this time, other potential devices, such as the WAN PHY on Turris 1.x, cannot use the MDIO bus, since it may cause a bus conflict. Fix this issue by locking the MDIO bus even when we are accessing the PHY registers via ethernet management frames. Fixes: 2cd54856 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet") Signed-off-by:
Marek Behún <kabel@kernel.org> Reviewed-by:
Christian Marangi <ansuelsmth@gmail.com> Signed-off-by:
-
Marek Behún authored
Commit c766e077 ("net: dsa: qca8k: convert to regmap read/write API") introduced bulk read/write methods to qca8k's regmap. The regmap bulk read/write methods get the register address in a buffer passed as a void pointer parameter (the same buffer contains also the read/written values). The register address occupies only as many bytes as it requires at the beginning of this buffer. For example if the .reg_bits member in regmap_config is 16 (as is the case for this driver), the register address occupies only the first 2 bytes in this buffer, so it can be cast to u16. But the original commit implementing these bulk read/write methods cast the buffer to u32: u32 reg = *(u32 *)reg_buf & U16_MAX; taking the first 4 bytes. This works on little endian systems where the first 2 bytes of the buffer correspond to the low 16-bits, but it obviously cannot work on big endian systems. Fix this by casting the beginning of the buffer to u16 as u32 reg = *(u16 *)reg_buf; Fixes: c766e077 ("net: dsa: qca8k: convert to regmap read/write API") Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== Fixes for lynx-28g PHY driver This series fixes some issues in the Lynx 28G SerDes driver, namely an oops when unloading the module, a race between the periodic workqueue and the PHY API, and a race between phy_set_mode_ext() calls on multiple lanes on the same SerDes. ==================== Signed-off-by: -
Vladimir Oltean authored
The protocol converter configuration registers PCC8, PCCC, PCCD (implemented by the driver), as well as others, control protocol converters from multiple lanes (each represented as a different struct phy). So, if there are simultaneous calls to phy_set_mode_ext() to lanes sharing the same PCC register (either for the "old" or for the "new" protocol), corruption of the values programmed to hardware is possible, because lynx_28g_rmw() has no locking. Add a spinlock in the struct lynx_28g_priv shared by all lanes, and take the global spinlock from the phy_ops :: set_mode() implementation. There are no other callers which modify PCC registers. Fixes: 8f73b37c ("phy: add support for the Layerscape SerDes 28G") Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
-
Vladimir Oltean authored
lynx_28g_cdr_lock_check() runs once per second in a workqueue to reset the lane receiver if the CDR has not locked onto bit transitions in the RX stream. But the PHY consumer may do stuff with the PHY simultaneously, and that isn't okay. Block concurrent generic PHY calls by holding the PHY mutex from this workqueue. Fixes: 8f73b37c ("phy: add support for the Layerscape SerDes 28G") Signed-off-by:
-
Ioana Ciornei authored
The blamed commit added the CDR check work item but didn't cancel it on the remove path. Fix this by adding a remove function which takes care of it. Fixes: 8f73b37c ("phy: add support for the Layerscape SerDes 28G") Signed-off-by:
Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by:
-
- 05 Oct, 2023 19 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Jakub Kicinski: "Including fixes from Bluetooth, netfilter, BPF and WiFi. I didn't collect precise data but feels like we've got a lot of 6.5 fixes here. WiFi fixes are most user-awaited. Current release - regressions: - Bluetooth: fix hci_link_tx_to RCU lock usage Current release - new code bugs: - bpf: mprog: fix maximum program check on mprog attachment - eth: ti: icssg-prueth: fix signedness bug in prueth_init_tx_chns() Previous releases - regressions: - ipv6: tcp: add a missing nf_reset_ct() in 3WHS handling - vringh: don't use vringh_kiov_advance() in vringh_iov_xfer(), it doesn't handle zero length like we expected - wifi: - cfg80211: fix cqm_config access race, fix crashes with brcmfmac - iwlwifi: mvm: handle PS changes in vif_cfg_changed - mac80211: fix mesh id corruption on 32 bit systems - mt76: mt76x02: fix MT76x0 external LNA gain handling - Bluetooth: fix handling of HCI_QUIRK_STRICT_DUPLICATE_FILTER - l2tp: fix handling of transhdrlen in __ip{,6}_append_data() - dsa: mv88e6xxx: avoid EEPROM timeout when EEPROM is absent - eth: stmmac: fix the incorrect parameter after refactoring Previous releases - always broken: - net: replace calls to sock->ops->connect() with kernel_connect(), prevent address rewrite in kernel_bind(); otherwise BPF hooks may modify arguments, unexpectedly to the caller - tcp: fix delayed ACKs when reads and writes align with MSS - bpf: - verifier: unconditionally reset backtrack_state masks on global func exit - s390: let arch_prepare_bpf_trampoline return program size, fix struct_ops offsets - sockmap: fix accounting of available bytes in presence of PEEKs - sockmap: reject sk_msg egress redirects to non-TCP sockets - ipv4/fib: send netlink notify when delete source address routes - ethtool: plca: fix width of reads when parsing netlink commands - netfilter: nft_payload: rebuild vlan header on h_proto access - Bluetooth: hci_codec: fix leaking memory of local_codecs - eth: intel: ice: always add legacy 32byte RXDID in supported_rxdids - eth: stmmac: - dwmac-stm32: fix resume on STM32 MCU - remove buggy and unneeded stmmac_poll_controller, depend on NAPI - ibmveth: always recompute TCP pseudo-header checksum, fix use of the driver with Open vSwitch - wifi: - rtw88: rtw8723d: fix MAC address offset in EEPROM - mt76: fix lock dependency problem for wed_lock - mwifiex: sanity check data reported by the device - iwlwifi: ensure ack flag is properly cleared - iwlwifi: mvm: fix a memory corruption due to bad pointer arithm - iwlwifi: mvm: fix incorrect usage of scan API Misc: - wifi: mac80211: work around Cisco AP 9115 VHT MPDU length" * tag 'net-6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (99 commits) MAINTAINERS: update Matthieu's email address mptcp: userspace pm allow creating id 0 subflow mptcp: fix delegated action races net: stmmac: remove unneeded stmmac_poll_controller net: lan743x: also select PHYLIB net: ethernet: mediatek: disable irq before schedule napi net: mana: Fix oversized sge0 for GSO packets net: mana: Fix the tso_bytes calculation net: mana: Fix TX CQE error handling netlink: annotate data-races around sk->sk_err sctp: update hb timer immediately after users change hb_interval sctp: update transport state when processing a dupcook packet tcp: fix delayed ACKs for MSS boundary condition tcp: fix quick-ack counting to count actual ACKs of new data page_pool: fix documentation typos tipc: fix a potential deadlock on &tx->lock net: stmmac: dwmac-stm32: fix resume on STM32 MCU ipv4: Set offload_failed flag in fibmatch results netfilter: nf_tables: nft_set_rbtree: fix spurious insertion failure netfilter: nf_tables: Deduplicate nft_register_obj audit logs ... -
Linus Torvalds authored
Merge tag 'integrity-v6.6-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity Pull integrity fixes from Mimi Zohar: "Two additional patches to fix the removal of the deprecated IMA_TRUSTED_KEYRING Kconfig" * tag 'integrity-v6.6-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity: ima: rework CONFIG_IMA dependency block ima: Finish deprecation of IMA_TRUSTED_KEYRING Kconfig
-
git://git.kernel.org/pub/scm/linux/kernel/git/lee/ledsLinus Torvalds authored
Pull LED fix from Lee Jones: "Just the one bug-fix: - Fix regression affecting LED_COLOR_ID_MULTI users" * tag 'leds-fixes-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: leds: Drop BUG_ON check for LED_COLOR_ID_MULTI
-
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfdLinus Torvalds authored
Pull MFD fixes from Lee Jones: "A couple of small fixes: - Potential build failure in CS42L43 - Device Tree bindings clean-up for a superseded patch" * tag 'mfd-fixes-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: dt-bindings: mfd: Revert "dt-bindings: mfd: maxim,max77693: Add USB connector" mfd: cs42l43: Fix MFD_CS42L43 dependency on REGMAP_IRQ
-
git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfsLinus Torvalds authored
Pull overlayfs fixes from Amir Goldstein: - Fix for file reference leak regression - Fix for NULL pointer deref regression - Fixes for RCU-walk race regressions: Two of the fixes were taken from Al's RCU pathwalk race fixes series with his consent [1]. Note that unlike most of Al's series, these two patches are not about racing with ->kill_sb() and they are also very recent regressions from v6.5, so I think it's worth getting them into v6.5.y. There is also a fix for an RCU pathwalk race with ->kill_sb(), which may have been solved in vfs generic code as you suggested, but it also rids overlayfs from a nasty hack, so I think it's worth anyway. Link: https://lore.kernel.org/linux-fsdevel/20231003204749.GA800259@ZenIV/ [1] * tag 'ovl-fixes-6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs: ovl: fix NULL pointer defer when encoding non-decodable lower fid ovl: make use of ->layers safe in rcu pathwalk ovl: fetch inode once in ovl_dentry_revalidate_common() ovl: move freeing ovl_entry past rcu delay ovl: fix file reference leak when submitting aio
-
Jakub Kicinski authored
Mat Martineau says: ==================== mptcp: Fixes and maintainer email update for v6.6 Patch 1 addresses a race condition in MPTCP "delegated actions" infrastructure. Affects v5.19 and later. Patch 2 removes an unnecessary restriction that did not allow additional outgoing subflows using the local address of the initial MPTCP subflow. v5.16 and later. Patch 3 updates Matthieu's email address. ==================== Link: https://lore.kernel.org/r/20231004-send-net-20231004-v1-0-28de4ac663ae@kernel.orgSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Matthieu Baerts authored
Use my kernel.org account instead. The other one will bounce by the end of the year. Signed-off-by:
Matthieu Baerts <matttbe@kernel.org> Signed-off-by:
Mat Martineau <martineau@kernel.org> Link: https://lore.kernel.org/r/20231004-send-net-20231004-v1-3-28de4ac663ae@kernel.orgSigned-off-by:
-
Geliang Tang authored
This patch drops id 0 limitation in mptcp_nl_cmd_sf_create() to allow creating additional subflows with the local addr ID 0. There is no reason not to allow additional subflows from this local address: we should be able to create new subflows from the initial endpoint. This limitation was breaking fullmesh support from userspace. Fixes: 702c2f64 ("mptcp: netlink: allow userspace-driven subflow establishment") Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/391 Cc: stable@vger.kernel.org Suggested-by:
Matthieu Baerts <matthieu.baerts@tessares.net> Reviewed-by:
Geliang Tang <geliang.tang@suse.com> Signed-off-by:
-
Paolo Abeni authored
The delegated action infrastructure is prone to the following race: different CPUs can try to schedule different delegated actions on the same subflow at the same time. Each of them will check different bits via mptcp_subflow_delegate(), and will try to schedule the action on the related per-cpu napi instance. Depending on the timing, both can observe an empty delegated list node, causing the same entry to be added simultaneously on two different lists. The root cause is that the delegated actions infra does not provide a single synchronization point. Address the issue reserving an additional bit to mark the subflow as scheduled for delegation. Acquiring such bit guarantee the caller to own the delegated list node, and being able to safely schedule the subflow. Clear such bit only when the subflow scheduling is completed, ensuring proper barrier in place. Additionally swap the meaning of the delegated_action bitmask, to allow the usage of the existing helper to set multiple bit at once. Fixes: bcd97734 ("mptcp: use delegate action to schedule 3rd ack retrans") Cc: stable@vger.kernel.org Reviewed-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
Remi Pommarel authored
Using netconsole netpoll_poll_dev could be called from interrupt context, thus using disable_irq() would cause the following kernel warning with CONFIG_DEBUG_ATOMIC_SLEEP enabled: BUG: sleeping function called from invalid context at kernel/irq/manage.c:137 in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 10, name: ksoftirqd/0 CPU: 0 PID: 10 Comm: ksoftirqd/0 Tainted: G W 5.15.42-00075-g816b502b2298-dirty #117 Hardware name: aml (r1) (DT) Call trace: dump_backtrace+0x0/0x270 show_stack+0x14/0x20 dump_stack_lvl+0x8c/0xac dump_stack+0x18/0x30 ___might_sleep+0x150/0x194 __might_sleep+0x64/0xbc synchronize_irq+0x8c/0x150 disable_irq+0x2c/0x40 stmmac_poll_controller+0x140/0x1a0 netpoll_poll_dev+0x6c/0x220 netpoll_send_skb+0x308/0x390 netpoll_send_udp+0x418/0x760 write_msg+0x118/0x140 [netconsole] console_unlock+0x404/0x500 vprintk_emit+0x118/0x250 dev_vprintk_emit+0x19c/0x1cc dev_printk_emit+0x90/0xa8 __dev_printk+0x78/0x9c _dev_warn+0xa4/0xbc ath10k_warn+0xe8/0xf0 [ath10k_core] ath10k_htt_txrx_compl_task+0x790/0x7fc [ath10k_core] ath10k_pci_napi_poll+0x98/0x1f4 [ath10k_pci] __napi_poll+0x58/0x1f4 net_rx_action+0x504/0x590 _stext+0x1b8/0x418 run_ksoftirqd+0x74/0xa4 smpboot_thread_fn+0x210/0x3c0 kthread+0x1fc/0x210 ret_from_fork+0x10/0x20 Since [0] .ndo_poll_controller is only needed if driver doesn't or partially use NAPI. Because stmmac does so, stmmac_poll_controller can be removed fixing the above warning. [0] commit ac3d9dd0 ("netpoll: make ndo_poll_controller() optional") Cc: <stable@vger.kernel.org> # 5.15.x Fixes: 47dd7a54 ("net: add support for STMicroelectronics Ethernet controllers") Signed-off-by:
Remi Pommarel <repk@triplefau.lt> Reviewed-by:
Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/1c156a6d8c9170bd6a17825f2277115525b4d50f.1696429960.git.repk@triplefau.ltSigned-off-by:
-
Randy Dunlap authored
Since FIXED_PHY depends on PHYLIB, PHYLIB needs to be set to avoid a kconfig warning: WARNING: unmet direct dependencies detected for FIXED_PHY Depends on [n]: NETDEVICES [=y] && PHYLIB [=n] Selected by [y]: - LAN743X [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICROCHIP [=y] && PCI [=y] && PTP_1588_CLOCK_OPTIONAL [=y] Fixes: 73c4d1b3 ("net: lan743x: select FIXED_PHY") Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Reported-by:
kernel test robot <lkp@intel.com> Closes: lore.kernel.org/r/202309261802.JPbRHwti-lkp@intel.com Cc: Bryan Whitehead <bryan.whitehead@microchip.com> Cc: UNGLinuxDriver@microchip.com Reviewed-by:
-
Christian Marangi authored
While searching for possible refactor of napi_schedule_prep and __napi_schedule it was notice that the mtk eth driver disable the interrupt for rx and tx AFTER napi is scheduled. While this is a very hard to repro case it might happen to have situation where the interrupt is disabled and never enabled again as the napi completes and the interrupt is enabled before. This is caused by the fact that a napi driven by interrupt expect a logic with: 1. interrupt received. napi prepared -> interrupt disabled -> napi scheduled 2. napi triggered. ring cleared -> interrupt enabled -> wait for new interrupt To prevent this case, disable the interrupt BEFORE the napi is scheduled. Fixes: 656e7052 ("net-next: mediatek: add support for MT7623 ethernet") Cc: stable@vger.kernel.org Signed-off-by:
-
Paolo Abeni authored
Haiyang Zhang says: ==================== net: mana: Fix some TX processing bugs Fix TX processing bugs on error handling, tso_bytes calculation, and sge0 size. ==================== Link: https://lore.kernel.org/r/1696020147-14989-1-git-send-email-haiyangz@microsoft.comSigned-off-by:
-
Haiyang Zhang authored
Handle the case when GSO SKB linear length is too large. MANA NIC requires GSO packets to put only the header part to SGE0, otherwise the TX queue may stop at the HW level. So, use 2 SGEs for the skb linear part which contains more than the packet header. Fixes: ca9c54d2 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)") Signed-off-by:
Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by:
Shradha Gupta <shradhagupta@linux.microsoft.com> Signed-off-by:
-
Haiyang Zhang authored
sizeof(struct hop_jumbo_hdr) is not part of tso_bytes, so remove the subtraction from header size. Cc: stable@vger.kernel.org Fixes: bd7fc6e1 ("net: mana: Add new MANA VF performance counters for easier troubleshooting") Signed-off-by:
-
Haiyang Zhang authored
For an unknown TX CQE error type (probably from a newer hardware), still free the SKB, update the queue tail, etc., otherwise the accounting will be wrong. Also, TX errors can be triggered by injecting corrupted packets, so replace the WARN_ONCE to ratelimited error logging. Cc: stable@vger.kernel.org Fixes: ca9c54d2 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)") Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/bristot/linuxLinus Torvalds authored
Pull rtla fixes from Daniel Bristot de Oliveira: "rtla (Real-Time Linux Analysis) tool fixes. Timerlat auto-analysis: - Timerlat is reporting thread interference time without thread noise events occurrence. It was caused because the thread interference variable was not reset after the analysis of a timerlat activation that did not hit the threshold. - The IRQ handler delay is estimated from the delta of the IRQ latency reported by timerlat, and the timestamp from IRQ handler start event. If the delta is near-zero, the drift from the external clock and the trace event and/or the overhead can cause the value to be negative. If the value is negative, print a zero-delay. - IRQ handlers happening after the timerlat thread event but before the stop tracing were being reported as IRQ that happened before the *current* IRQ occurrence. Ignore Previous IRQ noise in this condition because they are valid only for the *next* timerlat activation. Timerlat user-space: - Timerlat is stopping all user-space thread if a CPU becomes offline. Do not stop the entire tool if a CPU is/become offline, but only the thread of the unavailable CPU. Stop the tool only, if all threads leave because the CPUs become/are offline. man-pages: - Fix command line example in timerlat hist man page" * tag 'rtla-v6.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bristot/linux: rtla: fix a example in rtla-timerlat-hist.rst rtla/timerlat: Do not stop user-space if a cpu is offline rtla/timerlat_aa: Fix previous IRQ delay for IRQs that happens after thread sample rtla/timerlat_aa: Fix negative IRQ delay rtla/timerlat_aa: Zero thread sum after every sample analysis -
Eric Dumazet authored
syzbot caught another data-race in netlink when setting sk->sk_err. Annotate all of them for good measure. BUG: KCSAN: data-race in netlink_recvmsg / netlink_recvmsg write to 0xffff8881613bb220 of 4 bytes by task 28147 on cpu 0: netlink_recvmsg+0x448/0x780 net/netlink/af_netlink.c:1994 sock_recvmsg_nosec net/socket.c:1027 [inline] sock_recvmsg net/socket.c:1049 [inline] __sys_recvfrom+0x1f4/0x2e0 net/socket.c:2229 __do_sys_recvfrom net/socket.c:2247 [inline] __se_sys_recvfrom net/socket.c:2243 [inline] __x64_sys_recvfrom+0x78/0x90 net/socket.c:2243 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd write to 0xffff8881613bb220 of 4 bytes by task 28146 on cpu 1: netlink_recvmsg+0x448/0x780 net/netlink/af_netlink.c:1994 sock_recvmsg_nosec net/socket.c:1027 [inline] sock_recvmsg net/socket.c:1049 [inline] __sys_recvfrom+0x1f4/0x2e0 net/socket.c:2229 __do_sys_recvfrom net/socket.c:2247 [inline] __se_sys_recvfrom net/socket.c:2243 [inline] __x64_sys_recvfrom+0x78/0x90 net/socket.c:2243 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd value changed: 0x00000000 -> 0x00000016 Reported by Kernel Concurrency Sanitizer on: CPU: 1 PID: 28146 Comm: syz-executor.0 Not tainted 6.6.0-rc3-syzkaller-00055-g9ed22ae6 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/06/2023 Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Reviewed-by:
-
Xin Long authored
Currently, when hb_interval is changed by users, it won't take effect until the next expiry of hb timer. As the default value is 30s, users have to wait up to 30s to wait its hb_interval update to work. This becomes pretty bad in containers where a much smaller value is usually set on hb_interval. This patch improves it by resetting the hb timer immediately once the value of hb_interval is updated by users. Note that we don't address the already existing 'problem' when sending a heartbeat 'on demand' if one hb has just been sent(from the timer) mentioned in: https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg590224.htmlSigned-off-by:
Xin Long <lucien.xin@gmail.com> Reviewed-by:
-
