crystalcove pmic support from Shobhit. Patch series has all acks/r-bs from
other mainainers so ok to pull into drm-next. But I'm cc'ing all other
maintainers as fyi and in case they want to pull it into their trees too
to avoid conflicts.

* tag 'topic/crc-pmic-2015-07-23' of git://anongit.freedesktop.org/drm-intel:
  mfd: Add GPIOLIB dependency if INTEL_SOC_PMIC is to be enabled
  drm/i915: Backlight control using CRC PMIC based PWM driver
  drm/i915: Use the CRC gpio for panel enable/disable
  pwm: crc: Add Crystalcove (CRC) PWM driver
  mfd: intel_soc_pmic_core: ADD PWM lookup table for CRC PMIC based PWM
  mfd: intel_soc_pmic_crc: Add PWM cell device for Crystalcove PMIC
  mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO signal
  gpiolib: Add support for removing registered consumer lookup table

- prelim hw support dropped for skl after Damien fixed an ABI issue around
  planes
- legacy modesetting is done using atomic infrastructure now (Maarten)!
- more gen9 workarounds (Arun&Nick)
- MOCS programming (cache control for better performance) for skl/bxt
- vlv/chv dpll improvements (Ville)
- PSR fixes from Rodrigo
- fbc improvements from Paulo
- plumb requests into execlist submit functions (Mika)
- opregion code cleanup from Jani
- resource streamer support from Abdiel for mesa
- final fixes for 12bpc hdmi + enabling support from Ville
drm-intel-next-2015-07-03:
- dsi improvements (Gaurav)
- bxt ddi dpll hw state readout (Imre)
- chv dvfs support and overall wm improvements for both vlv and chv (Ville)
- ppgtt polish from Mika and Michel
- cdclk support for bxt (Bob Pauwe)
- make frontbuffer tracking more precise
- OLR removal (John Harrison)
- per-ctx WA batch buffer support (Arun Siluvery)
- remvoe KMS Kconfig option (Chris)
- more hpd handling refactoring from Jani
- use atomic states throughout modeset code and integrate with atomic plane
  update (Maarten)
drm-intel-next-2015-06-19:
- refactoring hpd irq handlers (Jani)
- polish skl dpll code a bit (Damien)
- dynamic cdclk adjustement (Ville & Mika)
- fix up 12bpc hdmi and enable it for real again (Ville)
- extend hsw cmd parser to be useful for atomic configuration (Franscico Jerez)
- even more atomic conversion and rolling state handling out across modeset code
  from Maarten & Ander
- fix DRRS idleness detection (Ramalingam)
- clean up dsp address alignment handling (Ville)
- some fbc cleanup patches from Paulo
- prevent hard-hangs when trying to reset the gpu on skl (Mika)

* tag 'drm-intel-next-2015-07-17' of git://anongit.freedesktop.org/drm-intel: (386 commits)
  drm/i915: Update DRIVER_DATE to 20150717
  drm/i915/skl: Drop the preliminary_hw_support flag
  drm/i915/skl: Don't expose the top most plane on gen9 display
  drm/i915: Fix divide by zero on watermark update
  drm/i915: Invert fastboot check
  drm/i915: Clarify logic for initial modeset
  drm/i915: Unconditionally check gmch pfit state
  drm/i915: always disable irqs in intel_pipe_update_start
  drm/i915: Remove use of runtime pm in atomic commit functions
  drm/i915: Call plane update functions directly from intel_atomic_commit.
  drm/i915: Use full atomic modeset.
  drm/i915/gen9: Add WaSetDisablePixMaskCammingAndRhwoInCommonSliceChicken
  drm/i915/gen9: Add WaFlushCoherentL3CacheLinesAtContextSwitch workaround
  drm/i915/gen9: Add WaDisableCtxRestoreArbitration workaround
  drm/i915: Enable WA batch buffers for Gen9
  drm/i915/gen9: Implement WaDisableKillLogic for gen 9
  drm/i915: Use expcitly fixed type in compat32 structs
  drm/i915: Fix noatomic crtc disabling, v2.
  drm/i915: fill in more mode members
  drm/i915: Added BXT check in HAS_CORE_RING_FREQ macro
  ...

Update drm-misc pull request since the first one didn't go in yet. Few
atomic helper patches, rejecting some old dri1 crap for modern drivers and
a few trivial things on top.

* tag 'topic/drm-misc-2015-07-23' of git://anongit.freedesktop.org/drm-intel:
  drm/mgag200: remove unneeded variable
  drm/mgag200: remove unused variables
  drm/atomic: Only update crtc->x/y if it's part of the state, v2.
  drm/fb: drop panic handling
  drm: Fix warning with make xmldocs caused by drm_irq.c
  drm/gem: rip out drm vma accounting for gem mmaps
  drm/fourcc: Add formats R8, RG88, GR88
  drm/atomic: Cleanup on error properly in the atomic ioctl.
  drm: Update plane->fb also for page_flip
  drm: remove redundant code form drm_ioc32.c
  drm: reset empty state in transitional helpers
  drm/crtc-helper: Fixup error handling in drm_helper_crtc_mode_set
  drm/atomic: Update old_fb after setting a property.
  drm: Remove useless blank line
  drm: Reject DRI1 hw lock ioctl functions for kms drivers
  drm: Convert drm_legacy_ctxbitmap_init to void return type
  drm: Turn off Legacy Context Functions

- Add Carrizo support for amdkfd, using the new amdgpu driver as the relevant
  kgd. The support includes interfaces with amdgpu both for gfx7 (Kaveri) and
  gfx8 (Carrizo). However, gfx7 interface is used for debugging purposes only,
  so amdkfd defaults to using radeon when Kaveri is installed.

I would like to note that no new IOCTLs are being introduced, and there is no
change in the current IOCTLs, as they are suited both for gfx7 and gfx8.

* tag 'drm-amdkfd-next-2015-07-20' of git://people.freedesktop.org/~gabbayo/linux:
  drm/amdkfd: Set correct doorbell packet type for Carrizo
  drm/amdkfd: Use generic defines in new amd headers
  drm/amdkfd: Implement create_map_queues() for Carrizo
  drm/amdkfd: fix runlist length calculation
  drm/amdkfd: Add support for VI in DQM
  drm/amdkfd: add support for VI in MQD manager
  drm/amdkfd: add CP HWS packet headers for VI
  drm/amdkfd: add supported CZ devices PCI IDs to amdkfd
  drm/amdkfd: Add dependency of DRM_AMDGPU to Kconfig
  drm/amdgpu: Add amdgpu <--> amdkfd gfx8 interface
  drm/amdgpu: add amdgpu <--> amdkfd gfx7 interface
  drm/amdgpu: Add H/W agnostic amdgpu <--> amdkfd interface
  drm/radeon: Modify kgd_engine_type enum to match CZ

This is needed as the CRC PMIC has support for Panel
enable/diable as gpio which needs 'gpiod_add_lookup_table'
and 'gpiod_remove_lookup_table' from gpiolib. This patch
can be squashed with below commit in topic/crc-pmic branch

    commit 61dd2ca2
    Author: Shobhit Kumar <shobhit.kumar@intel.com>
    Date:   Fri Jun 26 14:32:05 2015 +0530

    mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO
    signal

    On some Intel SoC platforms, the panel enable/disable signals
    are controlled by CRC PMIC. Add those control as a new GPIO in a
    lookup table for gpio-crystalcove chip during CRC driver load

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Use the CRC PWM device in intel_panel.c and add new MIPI backlight
specififc callbacks

v2: Modify to use pwm_config callback
v3: Addressed Jani's comments
    - Renamed all function as pwm_* instead of vlv_*
    - Call intel_panel_actually_set_backlight in enable function
    - Return -ENODEV in case pwm_get fails
    - in case pwm_config error return error cdoe from pwm_config
    - Cleanup pwm in intel_panel_destroy_backlight
v4: Removed unused #defines and initialized backlight with INVALID_PIPE (Ville)

CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The CRC (Crystal Cove) PMIC, controls the panel enable and disable
signals for BYT for dsi panels. This is indicated in the VBT fields. Use
that to initialize and use GPIO based control for these signals.

v2: Use the newer gpiod interface(Alexandre)
v3: Remove the redundant checks and unused code (Ville)
v4: Moved PWM vs SoC backlight #defines to intel_bios.h (Jani)

CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The Crystalcove PMIC provides three PWM signals and this driver exports
one of them on the BYT platform which is used to control backlight for
DSI panel. This is platform device implementation of the drivers/mfd
cell device for CRC PMIC.

CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

On some BYT PLatform the PWM is controlled using CRC PMIC. Add a lookup
entry for the same to be used by the consumer (Intel GFX)

CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Needed for PWM control suuported by the PMIC

CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

On some Intel SoC platforms, the panel enable/disable signals are
controlled by CRC PMIC. Add those control as a new GPIO in a lookup
table for gpio-crystalcove chip during CRC driver load

CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

In case we unload and load a driver module again that is registering a
lookup table, without this it will result in multiple entries. Provide
an option to remove the lookup table on driver unload

Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: Ben Goz <ben.goz@amd.com>
Reviewed-by: Yair Shachar <yair.shachar@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

This patch makes use of the new amd headers (that are part of the new
amdgpu driver), instead of private defines.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

The MAP_QUEUES packet length for Carrizo is different than for Kaveri.
Therefore, we now need to calculate the runlist length with regard to the
underlying H/W.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

This patch adds support for the VI APU in the DQM module.

Most of the functionality of DQM is shared between CI and VI. Therefore,
only a handful of functions are required to be in the
H/W-specific part of DQM.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

This patch implements all the VI MQD manager functions.
This is done in a different file as the MQD format is different
between CI and VI
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

This patch adds the PCI IDs of supported CZ devices to the
supported_devices structure in amdkfd. That structure is used during the
amdkfd probing stage, to check if the currently probed device is eligible
to be handled by amdkfd.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

This patch adds the gfx8 interface file between amdgpu and amdkfd. This
interface file is currently in use when running on a Carrizo-based
system.

The interface itself is represented by a pointer to struct
kfd_dev. The pointer is located inside amdgpu_device structure.

All the register accesses that amdkfd need are done using this
interface. This allows us to avoid direct register accesses in
amdkfd proper, while also allows us to avoid locking between
amdkfd and amdgpu.

The single exception is the doorbells that are used in both of
the drivers. However, because they are located in separate pci
bar pages, the danger of sharing registers between the drivers
is minimal.

Having said that, we are planning to move the doorbells as well
to amdgpu.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

This patch adds the gfx7 interface file between amdgpu and amdkfd. This
interface file mirrors (some) of the functions in radeon_kfd.c
(the interface file between radeon and amdkfd).

The gfx7 interface is used when it is run on a Kaveri-based system.

This interface file was used for bring-up of amdkfd on amdgpu and for
debugging purposes. For users who would like to run HSA on Kaveri, please
use the radeon graphic driver.

Note: CONFIG_DRM_AMDGPU_CIK must be selected for amdgpu to handle Kaveri.

v2: removed MTYPE_NONCACHED enum definition as it is defined in another
patch
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

This patch adds an interface file between amdgpu and amdkfd. This
interface file is H/W agnostic, thus containing functions that
operate the same for any AMD APU/GPU H/W generation.

The functions in this interface mirror (some) of the functions in
radeon_kfd.c (the radeon<-->amdkfd interface file). The main functions
are:

- amdgpu_amdkfd_init - initialize the amdkfd module
- amdgpu_amdkfd_load_interface - load the H/W interface according to the
  currently probed device
- amdgpu_amdkfd_device_probe - probe the device in amdkfd
- amdgpu_amdkfd_device_init - initialize the device in amdkfd
- amdgpu_amdkfd_interrupt - call the ISR of amdkfd
- amdgpu_amdkfd_suspend - suspend callback from amdgpu
- amdgpu_amdkfd_resume - resume callback from amdgpu

This patch also modifies the relevant amdgpu files, to use this new
interface.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

This patch splits the KGD_ENGINE_SDMA to KGD_ENGINE_SDMA1 and
KGD_ENGINE_SDMA2 to match CZ definitions.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

Pull SCSI fixes from James Bottomley:
 "Two fairly simple fixes: one is a change that causes us to have a very
  low queue depth leading to performance issues and the other is a null
  deref occasionally in tapes thanks to use after put"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: fix host max depth checking for the 'queue_depth' sysfs interface
  st: null pointer dereference panic caused by use after kref_put by st_open

Pull MIPS fixes from Ralf Baechle:
 "Another round of MIPS fixes for 4.2.

  Things are looking quite decent at this stage but the recent work on
  the FPU support took its toll:

   - fix an incorrect overly restrictive ifdef

   - select O32 64-bit FP support for O32 binary compatibility

   - remove workarounds for Sibyte SB1250 Pass1 parts.  There are rare
     fixing the workarounds is not worth the effort.

   - patch up an outdated and now incorrect comment"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: fpu.h: Allow 64-bit FPU on a 64-bit MIPS R6 CPU
  MIPS: SB1: Remove support for Pass 1 parts.
  MIPS: Require O32 FP64 support for MIPS64 with O32 compat
  MIPS: asm-offset.c: Patch up various comments refering to the old filename.

Pull parisc fix from Helge Deller:
 "A memory leak fix from Christophe Jaillet which was introduced with
  kernel 4.0 and which leads to kernel crashes on parisc after 1-3 days"

* 'parisc-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: mm: Fix a memory leak related to pmd not attached to the pgd

Pull ARM SoC fixes from Olof Johansson:
 "By far most of the fixes here are updates to DTS files to deal with
  some mostly minor bugs.

  There's also a fix to deal with non-PM kernel configs on i.MX, a
  regression fix for ethernet on PXA platforms and a dependency fix for
  OMAP"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: keystone: dts: rename pcie nodes to help override status
  ARM: keystone: dts: fix dt bindings for PCIe
  ARM: pxa: fix dm9000 platform data regression
  ARM: dts: Correct audio input route & set mic bias for am335x-pepper
  ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX
  MAINTAINERS: digicolor: add dts files
  ARM: ux500: fix MMC/SD card regression
  ARM: ux500: define serial port aliases
  ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs
  ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs
  ARM: dts: Fix frequency scaling on Gumstix Pepper
  ARM: dts: configure regulators for Gumstix Pepper
  ARM: dts: omap3: overo: Update LCD panel names
  ARM: dts: cros-ec-keyboard: Add support for some Japanese keys
  ARM: imx6: gpc: always enable PU domain if CONFIG_PM is not set
  ARM: dts: imx53-qsb: fix TVE entry
  ARM: dts: mx23: fix iio-hwmon support
  ARM: dts: imx27: Adjust the GPT compatible string
  ARM: socfpga: dts: Fix entries order
  ARM: socfpga: dts: Fix adxl34x formating and compatible string

Commit 6134d949 ("MIPS: asm: fpu: Allow 64-bit FPU on MIPS32 R6")
added support for 64-bit FPU on a 32-bit MIPS R6 processor but it missed
the 64-bit CPU case leading to FPU failures when requesting FR=1 mode
(which is always the case for MIPS R6 userland) when running a 32-bit
kernel on a 64-bit CPU. We also fix the MIPS R2 case.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: 6134d949 ("MIPS: asm: fpu: Allow 64-bit FPU on MIPS32 R6")
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: <stable@vger.kernel.org> # 4.0+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10734/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Commit 0e0da48d ("parisc: mm: don't count preallocated pmds")
introduced a memory leak.

After this commit, the 'return' statement in pmd_free is executed in all
cases. Even for pmd that are not attached to the pgd.  So 'free_pages'
can never be called anymore, leading to a memory leak.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org  # v4.0+
Signed-off-by: Helge Deller <deller@gmx.de>

Merge "pxa fixes for v4.2" from Robert Jarzmik:

ARM: pxa: fixes for v4.2-rc2

This single fix reenables ethernet cards for several pxa boards,
broken by regulator addition to dm9000 driver.

* tag 'pxa-fixes-v4.2-rc2' of https://github.com/rjarzmik/linux:
  ARM: pxa: fix dm9000 platform data regression

Pull ARM fixes from Russell King:
 "A small set of ARM fixes for -rc3, most of them not far off
  one-liners, with the exception of fixing the V7 cache invalidation for
  incoming SMP processors which was causing problems for SoCFPGA
  devices"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: fix __virt_to_idmap build error on !MMU
  ARM: invalidate L1 before enabling coherency
  ARM: 8404/1: dma-mapping: fix off-by-one error in bitmap size check
  ARM: 8402/1: perf: Don't use of_node after putting it
  ARM: 8400/1: use virt_to_idmap to get phys_reset address

Pull x86 fixes from Ingo Molnar:
 "Two families of fixes:

   - Fix an FPU context related boot crash on newer x86 hardware with
     larger context sizes than what most people test.  To fix this
     without ugly kludges or extensive reverts we had to touch core task
     allocator, to allow x86 to determine the task size dynamically, at
     boot time.

     I've tested it on a number of x86 platforms, and I cross-built it
     to a handful of architectures:

                                        (warns)               (warns)
       testing     x86-64:  -git:  pass (    0),  -tip:  pass (    0)
       testing     x86-32:  -git:  pass (    0),  -tip:  pass (    0)
       testing        arm:  -git:  pass ( 1359),  -tip:  pass ( 1359)
       testing       cris:  -git:  pass ( 1031),  -tip:  pass ( 1031)
       testing       m32r:  -git:  pass ( 1135),  -tip:  pass ( 1135)
       testing       m68k:  -git:  pass ( 1471),  -tip:  pass ( 1471)
       testing       mips:  -git:  pass ( 1162),  -tip:  pass ( 1162)
       testing    mn10300:  -git:  pass ( 1058),  -tip:  pass ( 1058)
       testing     parisc:  -git:  pass ( 1846),  -tip:  pass ( 1846)
       testing      sparc:  -git:  pass ( 1185),  -tip:  pass ( 1185)

     ... so I hope the cross-arch impact 'none', as intended.

     (by Dave Hansen)

   - Fix various NMI handling related bugs unearthed by the big asm code
     rewrite and generally make the NMI code more robust and more
     maintainable while at it.  These changes are a bit late in the
     cycle, I hope they are still acceptable.

     (by Andy Lutomirski)"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/fpu, sched: Introduce CONFIG_ARCH_WANTS_DYNAMIC_TASK_STRUCT and use it on x86
  x86/fpu, sched: Dynamically allocate 'struct fpu'
  x86/entry/64, x86/nmi/64: Add CONFIG_DEBUG_ENTRY NMI testing code
  x86/nmi/64: Make the "NMI executing" variable more consistent
  x86/nmi/64: Minor asm simplification
  x86/nmi/64: Use DF to avoid userspace RSP confusing nested NMI detection
  x86/nmi/64: Reorder nested NMI checks
  x86/nmi/64: Improve nested NMI comments
  x86/nmi/64: Switch stacks on userspace NMI entry
  x86/nmi/64: Remove asm code that saves CR2
  x86/nmi: Enable nested do_nmi() handling for 64-bit kernels

Pull timer fix from Ingo Molnar:
 "Fix for a misplaced export that can cause build failures in certain
  (rare) Kconfig situations"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick: Move the export of tick_broadcast_oneshot_control to the proper place

Pull scheduler fix from Ingo Molnar:
 "A oneliner rq throttling fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Test list head instead of list entry in throttle_cfs_rq()

Pull perf fixes from Ingo Molnar:
 "Mostly tooling fixes, plus a static key fix fixing /sys/devices/cpu/rdpmc"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools: Really allow to specify custom CC, AR or LD
  perf auxtrace: Fix misplaced check for HAVE_SYNC_COMPARE_AND_SWAP_SUPPORT
  perf hists browser: Take the --comm, --dsos, etc filters into account
  perf symbols: Store if there is a filter in place
  x86, perf: Fix static_key bug in load_mm_cr4()
  tools: Copy lib/hweight.c from the kernel sources
  perf tools: Fix the detached tarball wrt rbtree copy
  perf thread_map: Fix the sizeof() calculation for map entries
  tools lib: Improve clean target
  perf stat: Fix shadow declaration of close
  perf tools: Fix lockup using 32-bit compat vdso

Pull irq fixes from Ingo Molnar:
 "Misc irq fixes:

   - two driver fixes
   - a Xen regression fix
   - a nested irq thread crash fix"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gicv3-its: Fix mapping of LPIs to collections
  genirq: Prevent resend to interrupts marked IRQ_NESTED_THREAD
  genirq: Revert sparse irq locking around __cpu_up() and move it to x86 for now
  gpio/davinci: Fix race in installing chained irq handler

Merge fixes from Andrew Morton:
 "25 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (25 commits)
  lib/decompress: set the compressor name to NULL on error
  mm/cma_debug: correct size input to bitmap function
  mm/cma_debug: fix debugging alloc/free interface
  mm/page_owner: set correct gfp_mask on page_owner
  mm/page_owner: fix possible access violation
  fsnotify: fix oops in fsnotify_clear_marks_by_group_flags()
  /proc/$PID/cmdline: fixup empty ARGV case
  dma-debug: skip debug_dma_assert_idle() when disabled
  hexdump: fix for non-aligned buffers
  checkpatch: fix long line messages about patch context
  mm: clean up per architecture MM hook header files
  MAINTAINERS: uclinux-h8-devel is moderated for non-subscribers
  mailmap: update Sudeep Holla's email id
  Update Viresh Kumar's email address
  mm, meminit: suppress unused memory variable warning
  configfs: fix kernel infoleak through user-controlled format string
  include, lib: add __printf attributes to several function prototypes
  s390/hugetlb: add hugepages_supported define
  mm: hugetlb: allow hugepages_supported to be architecture specific
  revert "s390/mm: make hugepages_supported a boot time decision"
  ...