Add the PLL clock initialisation and clock registration
and include the clocks sourced via CLKDIVx for most of
the on-chip peripherals.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add TICK_MAX definition for the timer code
as the S3C64XX series have 32bit capable
PWM timers.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the initial clocks definitions for the s3c6400
and s3c6410. Move the epll and ext clock from the
s3c2443 support into the common code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add definitions for the s3c6400 epll and main pll
as well as functions to decode the rate. Add
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the common initialisation code for both the
S3C6400 and S3C6410, the UART registration.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the physical to virtual memory mapping and the
necessary interrupt demuxing for the PWM timer blocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The pwm-clock.c needs <mach/map.h> which is included
via other means on S3C24XX systems, so ensure it is
explicitly included.

Remove the includes of regs-clock.h and regs-gpio.h as
these are not needed by the build.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the necessary support for the timer on the
S3C6400 and S3C6410 by adding <mach/tick.h>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add and initialise the two VIC (PL192) found on
the S3C64XX series CPUs.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Initial support for the Samsung S3C6410 SoC.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Initialise the basic physical to virtual mappings and
then detect the CPU that the system is being run on so
that the cpu code code can call the correct initialisation
code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add IRQ definitions for the VIC0 and VIC1 interrupts
on the S3C6400 and S3C6410 SoCs.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add resources and information for the UART deviecs
on the S3C64XX CPUs.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the necessary defines for <mach/uncompress.h>
to function and build an working header code block.
Signed-off-by: Ben Doioks <ben-linux@fluff.org>

Initial clock register defines.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the necessary support for the kernel low-level
debug macros via <mach/debug-macro.S>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the include for the interrupt entry macros needed
to be included by <mach/entry-macro.S> for the kernel
interrupt handler.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the initial header files for the S3C64XX support to satisfy the
minimal requirements to build a kernel. Some definitions will therefore
be placeholders or empty functions that will ensure that the system can
build and have base functionality. These will be filled in at a later
date.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the initial PLAT_S3C64XX support files
and directory structure.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Split the timer pending code out to a seperate per-machine
header so that when compiling for mach-s3c2410 or mach-s3c24a0
we can use the right timer code without having to #ifdef the
timer driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Initial architecture support for the S3C24A0 ARCH_S3C24A0.

We don't yet add an kconfig entry in the main arch/arm/Kconfig
file as the series is not complete, so that is left until enough
support is in to be useful.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Split the map.h definitions into common S3C24XX code by
adding arch/arm/plat-s3c24xx/include/plat/map.h and
altering the machine specific header for the S3C24A0.

As we add a new <plat/map.h> we move the original one
in arch/arm/plat-s3c include directory to be called
map-base.h to distinguish the two files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add serial support for S3C24A0, based on current S3C2410
UART driver. It adds necessary new defines in regs-serial.h
for S3C24A0 and the code to support this device in
drivers/serial/s3c24a0.c
Signed-off-by: Sandeep Patil <sandeep.patil@azingo.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the necessary debug macros for the S3C24A0 to enable
kernel debugging, and fix a bug with selecting the wrong
default debug implementation from the base include.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The definition of S3C24XX_VA_GPIO used S3C2410_PA_GPIO
where it should have read S3C24XX_PA_GPIO.
Signed-off-by: Sandeep Patil <sandeep.patil@azingo.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add initial arch/arm/mach-s3c24a0/include/mach header
files for supporting Samsung S3C24A0 SoC.
Signed-off-by: Sandeep Patil <sandeep.patil@azingo.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The pwm-scaler0 and pwm-scaler1 clocks have their
.id field set to -1 as they are not referenced to
any specific device. However, parts of the pwm-clock
code used the .id field to identify which scaler
clock was being used.

Fix the problem by comparing against the pointer to
the clock to identify the scalers.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add the set_rate and round_rate methods for the pwm-scaler
clock for use with the time code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

All the s3c24xx gpiolib chips share the same get/set
calls and all but one bank shares the same calls for
.direction_input and .direction_output methods.

Change the initialisation process to use an new call
to register the chips that fills in any blank calls
with the default values to avoid having to fill them
in the structure initialisers.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add a simple check when registering a clock on whether
the clock has already been added to the list.

Any attempt to re-register a clock will cause the
clock list to be come looped and thus produces silent
failures when looking up clocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Move pwm-clock.c to arch/arm/plat-s3c
to be shared with the S3C64XX implementations.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Move the core clock registration and definitions
in arch/arm/plat-s3c24xx/clock.c to arch/arm/plat-s3c
to be shared with the S3C64XX implementations.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Move time.c to arch/arm/plat-s3c
to be shared with the S3C64XX implementations.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add a common include file (regs-irqtype.h) for the IRQ
trigger control register values S3C2410_EXTINT*.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Move clock.h, cpu.h and devs.h to plat-s3c for use
with the s3c64xx support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Update the clock settings on resume for suspend/resume
support so that if the boot loader changes anything or
the system's PLL is reset then we return with the correct
settings.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

We cannot sleep if we have cpufreq pm enabled during some
of the clock operations, so change to use a spinlock to
protect the clock system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add support for CPU frequency scalling to the S3C24XX serial
driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Move the PLL calculation code into it's own header
file for re-use with the other plat-s3c24xx based
systems such as the S3C24A0.

Note, we change the name of s3c2410_get_pll to the
more generically named s3c24xx_get_pll as well as
the related defintions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Only certain boards need these clocks, and they are not
available on some CPUs (such as the S3C24A0) so remove
them from arch/arm/plat-s3c24xx/clock.c and into their
own file with appropriate Kconfig entries.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>