In order to avoid conflicts with other include files, add
a prefix to the defines in xgbe.h.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull CIFS fixes from Steve French:
 "Small set of misc cifs/smb3 fixes"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  [CIFS] fix mount failure with broken pathnames when smb3 mount with mapchars option
  cifs: revalidate mapping prior to satisfying read_iter request with cache=loose
  fs/cifs: fix regression in cifs_create_mf_symlink()

Pull hwmon fixes from Guenter Roeck:
 "Various minor fixes"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (gpio-fan) Change name used in hwmon_device_register_with_groups
  hwmon: (emc1403) Fix missing 'select REGMAP_I2C' in Kconfig
  hwmon: (ntc_thermistor) Use the manufacturer name properly
  devicetree: bindings: Document murata vendor prefix
  hwmon: (w83l786ng) Report correct minimum fan speed

Pull networking fixes from David Miller:

 1) Fix crash in ipvs tot_stats estimator, from Julian Anastasov.

 2) Fix OOPS in nf_nat on netns removal, from Florian Westphal.

 3) Really really really fix locking issues in slip and slcan tty write
    wakeups, from Tyler Hall.

 4) Fix checksum offloading in fec driver, from Fugang Duan.

 5) Off by one in BPF instruction limit test, from Kees Cook.

 6) Need to clear all TSO capability flags when doing software TSO in
    tg3 driver, from Prashant Sreedharan.

 7) Fix memory leak in vlan_reorder_header() error path, from Li
    RongQing.

 8) Fix various bugs in xen-netfront and xen-netback multiqueue support,
    from David Vrabel and Wei Liu.

 9) Fix deadlock in cxgb4 driver, from Li RongQing.

10) Prevent double free of no-cache DST entries, from Eric Dumazet.

11) Bad csum_start handling in skb_segment() leads to crashes when
    forwarding, from Tom Herbert.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
  net: fix setting csum_start in skb_segment()
  ipv4: fix dst race in sk_dst_get()
  net: filter: Use kcalloc/kmalloc_array to allocate arrays
  trivial: net: filter: Change kerneldoc parameter order
  trivial: net: filter: Fix typo in comment
  net: allwinner: emac: Add missing free_irq
  cxgb4: use dev_port to identify ports
  xen-netback: bookkeep number of active queues in our own module
  tg3: Change nvram command timeout value to 50ms
  cxgb4: Not need to hold the adap_rcu_lock lock when read adap_rcu_list
  be2net: fix qnq mode detection on VFs
  of: mdio: fixup of_phy_register_fixed_link parsing of new bindings
  at86rf230: fix irq setup
  net: phy: at803x: fix coccinelle warnings
  net/mlx4_core: Fix the error flow when probing with invalid VF configuration
  tulip: Poll link status more frequently for Comet chips
  net: huawei_cdc_ncm: increase command buffer size
  drivers: net: cpsw: fix dual EMAC stall when connected to same switch
  xen-netfront: recreate queues correctly when reconnecting
  xen-netfront: fix oops when disconnected from backend
  ...

Dave Jones reported that a crash is occurring in

csum_partial
tcp_gso_segment
inet_gso_segment
? update_dl_migration
skb_mac_gso_segment
__skb_gso_segment
dev_hard_start_xmit
sch_direct_xmit
__dev_queue_xmit
? dev_hard_start_xmit
dev_queue_xmit
ip_finish_output
? ip_output
ip_output
ip_forward_finish
ip_forward
ip_rcv_finish
ip_rcv
__netif_receive_skb_core
? __netif_receive_skb_core
? trace_hardirqs_on
__netif_receive_skb
netif_receive_skb_internal
napi_gro_complete
? napi_gro_complete
dev_gro_receive
? dev_gro_receive
napi_gro_receive

It looks like a likely culprit is that SKB_GSO_CB()->csum_start is
not set correctly when doing non-scatter gather. We are using
offset as opposed to doffset.
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 7e2b10c1 ("net: Support for multiple checksums with gso")
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull NFS client fixes from Trond Myklebust:
 "Highlights include:

   - Stable fix for a data corruption case due to incorrect cache
     validation
   - Fix a couple of false positive cache invalidations
   - Fix NFSv4 security negotiation issues"

* tag 'nfs-for-3.16-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFSv4: test SECINFO RPC_AUTH_GSS pseudoflavors for support
  NFS Return -EPERM if no supported or matching SECINFO flavor
  NFS check the return of nfs4_negotiate_security in nfs4_submount
  NFS: Don't mark the data cache as invalid if it has been flushed
  NFS: Clear NFS_INO_REVAL_PAGECACHE when we update the file size
  nfs: Fix cache_validity check in nfs_write_pageuptodate()

If CONFIG_RFS_ACCEL=n:

drivers/net/ethernet/cisco/enic/enic_main.c: In function 'enic_open':
drivers/net/ethernet/cisco/enic/enic_main.c:1603:2: error: implicit declaration of function 'enic_rfs_flw_tbl_init' [-Werror=implicit-function-declaration]
drivers/net/ethernet/cisco/enic/enic_main.c: In function 'enic_stop':
drivers/net/ethernet/cisco/enic/enic_main.c:1630:2: error: implicit declaration of function 'enic_rfs_flw_tbl_free' [-Werror=implicit-function-declaration]

Introduced in commit a145df23 ("enic: Add
Accelerated RFS support").

Dummy functions are provided, but their prototypes are missing, causing the
build failure.  Provide dummy static inline functions instead to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The maximum window size is limited by the sequence gap field, which
was expanded with bd784533
("tipc: Expand link sequence gap field to 13 bits")
We remove the artificial limit that prevents the link window to be
set larger than 150.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-06-24

This series contains updates to i40e and i40evf.

Greg provides a patch to stop the VF device after setting its MAC address.
This is due to if the host VMM administrator has changed the VF device's MAC
address then the i40e driver needs to halt the VF device so that the
administrator will be forced to reload the VF driver so that the VF driver
will start using the newly assigned MAC address.

Shannon provides several patches for i40e, first makes prep_for_test() a
void function since the return value was being ignored for the most part
by all its callers.  Adds a log warning when the firmware's API minor/major
number is not what we expect to assist the user by informing them they
may need to update their NVM or SW.  Cleans up a stray print message
so that it is similar to other print messages.  Ensures to set the
WoL flag when setting LAA and allow the user to set LAA again.  So do
not short-circuit the LAA assignment when the driver thinks it has
already been done as it is possible that the user might want to force
the address setting again.  Provides a couple more LAA fixes to ensure
the LAA gets restored after resets.

Neerav provides a patch for i40e to add a PF reset when a malicious driver
event for the PF occurs.  As per the specification when the PF driver
receives a malicious driver event the queue that caused the event is
already stopped and it is expected that the function that owns the queue
will reset the queue, but in some cases it may not be possible to determine
the queue, so it is suggested to reset the whole function.

Carolyn fixes ethtool coalesce settings to allow 0 as a disable value and
adds message to user about invalid values.

Jesse removes a reserved type which was not removed from the code.

Catherine provides a patch to add the ability to enable/disable link from
set_link)restart_an() which will make it easy to toggle link without
calling set_phy_config() when no other link settings need to change.

Anjali provides a patch to ensure we do a PF reset on Tx hang and that
way we avoid any Malicious Driver Detect (MDD) events because of a Tx
queue disable failure.

v2:
 - fixed the un-needed return in patch 2 based on feedback from Sergei Shtylyov
 - added punctuation to print statements and code comment based on
   feedback from Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use bool instead of int as the return type.

All uses are tested with !.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When IP route cache had been removed in linux-3.6, we broke assumption
that dst entries were all freed after rcu grace period. DST_NOCACHE
dst were supposed to be freed from dst_release(). But it appears
we want to keep such dst around, either in UDP sockets or tunnels.

In sk_dst_get() we need to make sure dst refcount is not 0
before incrementing it, or else we might end up freeing a dst
twice.

DST_NOCACHE set on a dst does not mean this dst can not be attached
to a socket or a tunnel.

Then, before actual freeing, we need to observe a rcu grace period
to make sure all other cpus can catch the fact the dst is no longer
usable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dormando <dormando@rydia.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use kcalloc/kmalloc_array to make it clear we're allocating arrays. No
integer overflow can actually happen here, since len/flen is guaranteed
to be less than BPF_MAXINSNS (4096). However, this changed makes sure
we're not going to get one if BPF_MAXINSNS were ever increased.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the order of the parameters to sk_unattached_filter_create() in
the kerneldoc to reflect the order they appear in the actual function.

This fix is only cosmetic, in the generated doc they still appear in the
correct order without the fix.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It seems overkill to use vmalloc() for typical listeners with less than
2048 hash buckets. Try kmalloc() and fallback to vmalloc() to reduce TLB
pressure.

Use kvfree() helper as it is now available.
Use ilog2() instead of a loop.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is trivial to add netpoll support to veth, since
it is not a stacked device, we don't need to setup and
clean up netpoll.
Reported-by: Stefan Priebe <s.priebe@profihost.ag>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the mdio probe function fails in emac_open, the interrupt we just requested
isn't freed. If emac_open is called again, for example because we try to set up
the interface again, the kernel will oops because the interrupt wasn't properly
released.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.11+
Signed-off-by: David S. Miller <davem@davemloft.net>

Jitendra Kalsaria says:

====================
Rebranding changes for bnx2 and cnic driver

The following set of patches are for rebranding Broadcom bnx2 and cnic driver as QLogic drivers.
Please apply this series to net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o QLogic has acquired the NetXtremeII products and drivers from Broadcom.
  This patch re-brands cnic driver as a QLogic driver
Signed-off-by: David S. Miller <davem@davemloft.net>

o QLogic has acquired the NetXtremeII products and drivers from Broadcom.
  This patch re-brands bnx2 driver as a QLogic driver
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix checkpatch warning:
WARNING: kfree(NULL) is safe this check is probably not required

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: netdev@vger.kernel.org
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
crc32 combine improvements

So almost a month passed, and I don't want this to get lost
somewhere. I have applied the feedback given at that time to
this set, rebased plus tested it against latest net-next. I
decided to route this via netdev as it improves performance
upon library code that provides library bits for SCTP, i.e.
for non-linear skb csum handling in IPVS. Thus, resending
this for George before it gets lost.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In case they help the compiler.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So it gets discarded after the selftest.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's no need for a full 32x32 matrix, when rows before the last are
just shifted copies of the rows after them.

There's still room for improvement (especially on X86 processors with
CRC32 and PCLMUL instructions), but this is a large step in the
right direction [which is in particular useful for its current user,
namely SCTP checksumming over multiple skb frags[] entries, i.e. in
IPVS balancing when other CRC32 offloads are not available].

The internal primitive is now called crc32_generic_shift and takes one
less argument; the XOR with crc2 is done in inline wrappers.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 3f85944f ("net: Add sysfs file
for port number") introduce dev_port to network devices. cxgb4 adapters
have multiple ports on the same PCI function, and used dev_id to
identify those ports. That use was removed by commit
8c367fcb ("cxgb4: Do not set
net_device::dev_id to VI index"), since dev_id should be used only when
devices share the same MAC address.

Using dev_port for cxgb4 allows different ports on the same PCI function
to be identified.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original code uses netdev->real_num_tx_queues to bookkeep number of
queues and invokes netif_set_real_num_tx_queues to set the number of
queues. However, netif_set_real_num_tx_queues doesn't allow
real_num_tx_queues to be smaller than 1, which means setting the number
to 0 will not work and real_num_tx_queues is untouched.

This is bogus when xenvif_free is invoked before any number of queues is
allocated. That function needs to iterate through all queues to free
resources. Using the wrong number of queues results in NULL pointer
dereference.

So we bookkeep the number of queues in xen-netback to solve this
problem. This fixes a regression introduced by multiqueue patchset in
3.16-rc1.

There's another bug in original code that the real number of RX queues
is never set. In current Xen multiqueue design, the number of TX queues
and RX queues are in fact the same. We need to set the numbers of TX and
RX queues to the same value.

Also remove xenvif_select_queue and leave queue selection to core
driver, as suggested by David Miller.
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
CC: Ian Campbell <ian.campbell@citrix.com>
CC: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 506724c4 "tg3: Override clock,
link aware and link idle mode during NVRAM dump" changed the timeout
value for nvram command execution from 100ms to 1ms. But the 1ms
timeout value was only sufficient for nvram read operations but not
write operations for most of the devices supported by tg3 driver.
This patch sets the MAX to 50ms. Also it uses usleep_range instead
of udelay.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 648cd48c
The hwmon name attributes must not include '-' so the name must be
rename from gpio-fan to gpio_fan
Signed-off-by: Julien D'Ascenzio <jdascenzio@yahoo.fr>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Pull ARM SoC fixes from Arnd Bergmann:
 "A new set of bug fixes for 3.16, containing patches for seven
  platforms:

  at91:
    - drivers/misc fix for Kconfig PWM symbol
    - correction of several values in DT after conversion to CCF
    - fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc

  imx:
    - Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
      because controller base CD/WP is not working in esdhc driver due to
      runtime PM support
    - A couple of random ventana gw5xxx board fixes
    - Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
      IPUv3 driver out of staging tree
    - Fix enet/fec clock selection on imx6sl
    - Fix display node on imx53-m53evk board
    - A couple of Cubox-i updates from Russell, which were omitted from
      the merge window due to dependency

  integrator:
    - fix an OF-related regression against 3.15

  mvebu:
    - mvebu (v7)
       - Fix broken SoC ID detection
       - Select ARM_CPU_SUSPEND for v7
       - Remove armada38x compatible string (no users yet)
       - Enable Dove SoC in mvebu_v7_defconfig
    - kirkwood
       - Fix phy-connection-type on GuruPlug board

  qcom:
    - enable gsbi driver in defconfig
    - fix section mismatch warning in serial driver

  samsung:
    - use WFI macro in platform_do_lowpower because exynos cpuhotplug
      includes a hardcoded WFI instruction and it causes compile error
      in Thumb-2 mode.
    - fix GIC reg sizes for exynos4 SoCs
    - remove reset timer counter value during boot and resume for mct
      to fix a big jump in printk timestamps
    - fix pm code to check cortex-A9 for another exynos SoCs
    - don't rely on firmware's secondary_cpu_start for mcpm

  sti:
    - Ethernet clocks were wrongly defined for STiH415/416 platforms
    - STiH416 B2020 revision E DTS file name contained uppercase, change to
      lowercase"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
  ARM: at91/dt: sam9261: remove slow RC osc
  ARM: at91/dt: define sam9261ek slow crystal frequency
  ARM: at91/dt: sam9261: correctly define mainck
  ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
  ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
  misc: atmel_pwm: fix Kconfig symbols
  ARM: integrator: fix OF-related regression
  ARM: mvebu: Fix the improper use of the compatible string armada38x using a wildcard
  ARM: dts: kirkwood: fix phy-connection-type for Guruplug
  ARM: EXYNOS: Don't rely on firmware's secondary_cpu_start for mcpm
  ARM: dts: imx51-eukrea-mbimxsd51-baseboard: unbreak esdhc.
  ARM: dts: imx51-babbage: Fix esdhc setup
  ARM: dts: mx5: Move the display out of soc {} node
  ARM: dts: mx5: Fix IPU port node placement
  ARM: mvebu: select ARM_CPU_SUSPEND for Marvell EBU v7 platforms
  ARM: mvebu: Fix broken SoC ID detection
  ARM: imx_v6_v7_defconfig: Enable CONFIG_IMX_IPUV3_CORE
  ARM: multi_v7_defconfig: Add QCOM GSBI driver
  ARM: stih41x: Rename stih416-b2020-revE.dts to stih416-b2020e.dts
  tty: serial: msm: Fix section mismatch warning
  ...

Merge "First AT91 fixes batch for 3.16" from Nicolas Ferre:

- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc

* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
  ARM: at91/dt: sam9261: remove slow RC osc
  ARM: at91/dt: define sam9261ek slow crystal frequency
  ARM: at91/dt: sam9261: correctly define mainck
  ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
  ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
  misc: atmel_pwm: fix Kconfig symbols

Merge "mvebu fixes for v3.16" from Jason Cooper:

 - mvebu
    - Fix broken SoC ID detection
    - Select ARM_CPU_SUSPEND for v7
    - Remove armada38x compatible string (no users yet)

 - kirkwood
    - Fix phy-connection-type on GuruPlug board

* tag 'mvebu-fixes-3.16' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: Fix the improper use of the compatible string armada38x using a wildcard
  ARM: dts: kirkwood: fix phy-connection-type for Guruplug
  ARM: mvebu: select ARM_CPU_SUSPEND for Marvell EBU v7 platforms
  ARM: mvebu: Fix broken SoC ID detection

Pull Ceph fix from Sage Weil:
 "This fixes a corner case for cloned RBD images"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: handle parent_overlap on writes correctly

The at91sam9261 doesn't actually have a slow RC oscillator, remove it from the
dtsi.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Define at91sam9261ek's slow crystal frequencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

mainck (CKGR_MCFR register) is actually using main_osc (CKGR_MOR register).
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

ICPLL can only take 0 or 1, it got mixed with OUT which can be in the [0-3]
range.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

ICPLL can only take 0 or 1, it got mixed with OUT which can be in the [0-3]
range.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>