I've been hitting a NULL ptr deref while using netconsole because the
np->dev check and the pointer manipulation in netpoll_cleanup are done
without rtnl and the following sequence happens when having a netconsole
over a vlan and we remove the vlan while disabling the netconsole:
	CPU 1					CPU2
					removes vlan and calls the notifier
enters store_enabled(), calls
netdev_cleanup which checks np->dev
and then waits for rtnl
					executes the netconsole netdev
					release notifier making np->dev
					== NULL and releases rtnl
continues to dereference a member of
np->dev which at this point is == NULL
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch 136d8f37 broke the skge driver.
Note this part of the patch:
+               if (skge_rx_setup(skge, e, nskb, skge->rx_buf_size) < 0) {
+                       dev_kfree_skb(nskb);
+                       goto resubmit;
+               }
+
                pci_unmap_single(skge->hw->pdev,
                                 dma_unmap_addr(e, mapaddr),
                                 dma_unmap_len(e, maplen),
                                 PCI_DMA_FROMDEVICE);
                skb = e->skb;
                prefetch(skb->data);
-               skge_rx_setup(skge, e, nskb, skge->rx_buf_size);

The function skge_rx_setup modifies e->skb to point to the new skb. Thus,
after this change, the new buffer, not the old, is returned to the
networking stack.

This bug is present in kernels 3.11, 3.11.1 and 3.12-rc1. The patch should
be queued for 3.11-stable.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Vasiliy Glazov <vascom2@gmail.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If local fragmentation is allowed, then ip_select_ident() and
ip_select_ident_more() need to generate unique IDs to ensure
correct defragmentation on the peer.

For example, if IPsec (tunnel mode) has to encrypt large skbs
that have local_df bit set, then all IP fragments that belonged
to different ESP datagrams would have used the same identificator.
If one of these IP fragments would get lost or reordered, then
peer could possibly stitch together wrong IP fragments that did
not belong to the same datagram. This would lead to a packet loss
or data corruption.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->data already points to IP header, but for the sake of
consistency we can also use ip_hdr() to retrieve it.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without this patch, if a frontend cycles through states Closing
and Closed (which Windows frontends need to do) then the netdev
will be destroyed and requires re-invocation of hotplug scripts
to restore state before the frontend can move to Connected. Thus
when udev is not in use the backend gets stuck in InitWait.

With this patch, the netdev is left alone whilst the backend is
still online and is only de-registered and freed just prior to
destroying the vif (which is also nicely symmetrical with the
netdev allocation and registration being done during probe) so
no re-invocation of hotplug scripts is required.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DCCP shouldn't be setting sk_err on redirects as it
isn't an error condition. it should be doing exactly
what tcp is doing and leaving the error handler without
touching the socket.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 104a43ed
    cnic: Use CHIP_NUM macros from bnx2x.h

changed the code to use the bnx2x macro NO_FCOE() to determine if FCoE
is supported or not.  There is another place in cnic that is still using
the old method to determine if FCoE is supported or not.  The 2 methods
may not yield the same result after the network interface is brought down
and up.  This will cause the crash as cnic_bnx2x_service_kcq() will access
the uninitialized cp->kcq2.

The fix is to consistently use the same macro CNIC_SUPPORTS_FCOE() which
uses the bnx2x NO_FCOE() macro.  As a follow-up, we can clean up the code
to remove the old method as it is no longer needed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit b9871bcf
    bnx2x: VF RSS support - PF side

changed the configuration of the doorbell HW and it broke iSCSI and FCoE.
We fix this by making compatible changes to the doorbell address in bnx2i
and bnx2fc.  For the userspace driver, we need to pass a modified CID
so that the existing userspace driver will calculate the correct doorbell
address and continue to work.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Included change:
- fix the Bridge Loop Avoidance component by marking the variables containing
  the VLAN ID with the HAS_TAG flag when needed.

Pablo Neira Ayuso says:

====================
The following patchset contains Netfilter fixes for you net tree,
mostly targeted to ipset, they are:

* Fix ICMPv6 NAT due to wrong comparison, code instead of type, from
  Phil Oester.

* Fix RCU race in conntrack extensions release path, from Michal Kubecek.

* Fix missing inversion in the userspace ipset test command match if
  the nomatch option is specified, from Jozsef Kadlecsik.

* Skip layer 4 protocol matching in ipset in case of IPv6 fragments,
  also from Jozsef Kadlecsik.

* Fix sequence adjustment in nfnetlink_queue due to using the netlink
  skb instead of the network skb, from Gao feng.

* Make sure we cannot swap of sets with different layer 3 family in
  ipset, from Jozsef Kadlecsik.

* Fix possible bogus matching in ipset if hash sets with net elements
  are used, from Oliver Smith.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit afbd8bae
   vxlan: add implicit fdb entry for default destination
creates an implicit fdb entry for default destination. This results
in an invalid fdb entry if default destination is not specified.
For ex:
  ip link add vxlan1 type vxlan id 100
creates the following fdb entry
  00:00:00:00:00:00 dev vxlan1 dst 0.0.0.0 self permanent

This patch fixes this issue by creating an fdb entry only if a
valid default destination is specified.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 1b7fdd2a ("tcp: do not use cached RTT for RTT estimation")
did not correctly account for the fact that crtt is the RTT shifted
left 3 bits. Fix the calculation to consistently reflect this fact.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-By: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

clears following warnings :
WARNING: Use include <linux/io.h> instead of <asm/io.h>
WARNING: Use include <linux/uaccess.h> instead of <asm/uaccess.h>
Signed-off-by: Avinash Kumar <avi.kp.137@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It has recently turned up that we have a number of long standing bugs
in the network stack cleanup code with use of the loopback device
after it has been freed that have not turned up because in most cases
the storage allocated to the loopback device is not reused, when those
accesses happen.

Set looback_dev to NULL to trigger oopses instead of silent data corrupt
when we hit this class of bug.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When receiving or sending a packet a packet on a VLAN, the
vid has to be marked with the TAG flag in order to make any
component in batman-adv understand that the packet is coming
from a really tagged network.

This fix the Bridge Loop Avoidance behaviour which was not
able to send announces over VLAN interfaces.

Introduced by 0b1da1765fdb00ca5d53bc95c9abc70dfc9aae5b
("batman-adv: change VID semantic in the BLA code")
Signed-off-by: Antonio Quartulli <antonio@open-mesh.org>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>

Instead of the netlink skb.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Ben Hutchings says:

====================
Some bug fixes and future-proofing for the recently added SFC9120
support:

1. Minimal support for the 40G configuration.
2. Disable the incomplete PTP/hardware timestamping support.
3. Reset MAC stats properly after a firmware upgrade.
4. Re-check the datapath firmware capabilities after the controller is
reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Adapt the same behaviour for SCTP as present in TCP for ICMP redirect
messages. For IPv6, RFC4443, section 2.4. says:

  ...
  (e) An ICMPv6 error message MUST NOT be originated as a result of
      receiving the following:
  ...
       (e.2) An ICMPv6 redirect message [IPv6-DISC].
  ...

Therefore, do not report an error to user space, just invoke dst's redirect
callback and leave, same for IPv4 as done in TCP as well. The implication
w/o having this patch could be that the reception of such packets would
generate a poll notification and in worst case it could even tear down the
whole connection. Therefore, stop updating sk_err on redirects.
Reported-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use USB_DEVICE_AND_INTERFACE_INFO and USB_VENDOR_AND_INTERFACE_INFO
macros to reduce boilerplate.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: <stable@vger.kernel.org> # 3.0+ as far back as it applies cleanly
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

IFLA_IPTUN_LOCAL and IFLA_IPTUN_REMOTE were inverted.

Introduced by c075b130 (ip6tnl: advertise tunnel param via rtnl).
Signed-off-by: Ding Zhi <zhi.ding@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without this patch it is impossible to read et_swtype, because the 1
byte space is needed for the terminating null byte. The max expected
value is 0xF, so now it should be possible to read decimal form ("15")
and hex form ("0xF").
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.

Use correct bit for switch initialization and fix typo in the define.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Use separate table for alias entries in the ehea module, otherwise the
probe() function will operate on the separate ports instead of the
lhea-"root" entry of the device-tree

Addresses https://bugzilla.novell.com/show_bug.cgi?id=435215

[ Thadeu notes that: "... this issue might happen with the generation of
  initrd, when the scripts check for /sys/class/net/eth0/device/modalias,
  which links to the port device at
  /sys/devices/ibmebus/23c00400.lhea/port0/" ]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Olaf Hering <ohering@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes a serious bug affecting all hash types with a net element -
specifically, if a CIDR value is deleted such that none of the same size
exist any more, all larger (less-specific) values will then fail to
match. Adding back any prefix with a CIDR equal to or more specific than
the one deleted will fix it.

Steps to reproduce:
ipset -N test hash:net
ipset -A test 1.1.0.0/16
ipset -A test 2.2.2.0/24
ipset -T test 1.1.1.1           #1.1.1.1 IS in set
ipset -D test 2.2.2.0/24
ipset -T test 1.1.1.1           #1.1.1.1 IS NOT in set

This is due to the fact that the nets counter was unconditionally
decremented prior to the iteration that shifts up the entries. Now, we
first check if there is a proceeding entry and if not, decrement it and
return. Otherwise, we proceed to iterate and then zero the last element,
which, in most cases, will already be zero.
Signed-off-by: Oliver Smith <oliver@8.c.9.b.0.7.4.0.1.0.0.2.ip6.arpa>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>

This closes netfilter bugzilla #843, reported by Quentin Armitage.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>

The "nomatch" commandline flag should invert the matching at testing,
similarly to the --return-nomatch flag of the "set" match of iptables.
Until now it worked with the elements with "nomatch" flag only. From
now on it works with elements without the flag too, i.e:

 # ipset n test hash:net
 # ipset a test 10.0.0.0/24 nomatch
 # ipset t test 10.0.0.1
 10.0.0.1 is NOT in set test.
 # ipset t test 10.0.0.1 nomatch
 10.0.0.1 is in set test.

 # ipset a test 192.168.0.0/24
 # ipset t test 192.168.0.1
 192.168.0.1 is in set test.
 # ipset t test 192.168.0.1 nomatch
 192.168.0.1 is NOT in set test.

 Before the patch the results were

 ...
 # ipset t test 192.168.0.1
 192.168.0.1 is in set test.
 # ipset t test 192.168.0.1 nomatch
 192.168.0.1 is in set test.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>

Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>

When driver registration fails, we need to clean up the resources allocated
before. cxgb4 missed to destroy the workqueue allocated at the very beginning.

This patch destroies the workqueue when registration fails.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Antonio Alecrim Jr <antonio.alecrim@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

running bonding in ALB mode requires that learning packets be sent periodically,
so that the switch knows where to send responding traffic.  However, depending
on switch configuration, there may not be any need to send traffic at the
default rate of 3 packets per second, which represents little more than wasted
data.  Allow the ALB learning packet interval to be made configurable via sysfs
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Acked-by: Veaceslav Falico <vfalico@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 8390f814 "atm: nicstar: re-use native mac_pton() helper" did a
usefull thing. However, mac_pton() returns 1 in the case of the successfully
parsed input. This patch fixes a typo.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes sparse warnings when incorrectly handling the port number
and using int instead of unsigned int iterating through &vn->sock_list[].
Keeping the port as __be16 also makes things clearer wrt endianess.
Also, it was pointed out that vxlan_get_rx_port() had unnecessary checks
which got removed.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o At the time of firmware hang "adapter->need_fw_reset" variable gets
  set but after re-initialization of firmware OR at the time of VF
  re-initialization that variable was not getting cleared which
  was leading to failure in VF reset recovery.Fix it by clearing
  this variable before re-initializing VF
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The NULL deref happens when br_handle_frame is called between these
2 lines of del_nbp:
	dev->priv_flags &= ~IFF_BRIDGE_PORT;
	/* --> br_handle_frame is called at this time */
	netdev_rx_handler_unregister(dev);

In br_handle_frame the return of br_port_get_rcu(dev) is dereferenced
without check but br_port_get_rcu(dev) returns NULL if:
	!(dev->priv_flags & IFF_BRIDGE_PORT)

Eric Dumazet pointed out the testing of IFF_BRIDGE_PORT is not necessary
here since we're in rcu_read_lock and we have synchronize_net() in
netdev_rx_handler_unregister. So remove the testing of IFF_BRIDGE_PORT
and by the previous patch, make sure br_port_get_rcu is called in
bridging code.
Signed-off-by: Hong Zhiguo <zhiguohong@tencent.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

current br_port_get_rcu is problematic in bridging path
(NULL deref). Change these calls in netlink path first.
Signed-off-by: Hong Zhiguo <zhiguohong@tencent.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/toshiba/ps3_gelic_net.c

It's a NOOP since 2.6.35 and I will remove it one day ;)
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch proposes to remove the IRQF_DISABLED flag from
code in drivers/net/ethernet/smsc/

It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>