- 13 Jun, 2024 20 commits
-
-
Nuno Sa authored
Being this device a soft core, it's only supported on some/specific platforms. Hence add proper dependencies for the supported platforms. Also add COMPILE_TEST to increase the build coverage. Signed-off-by:
Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20240604-dev-axi-dac-kconfig-v1-1-99ccd03938d1@analog.comSigned-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Nuno Sa authored
Being this device a soft core, it's only supported on some/specific platforms. Hence add proper dependencies for the supported platforms. Also add COMPILE_TEST to increase the build coverage. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
Register caching is improving bus access a lot because of the register window bank setting. Previously, bank register was set for every register access. Now with caching, it happens only when changing bank which is very infrequent. Signed-off-by:
Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com> Link: https://lore.kernel.org/r/20240607081039.789079-1-inv.git-commit@tdk.comSigned-off-by:
-
Krzysztof Kozlowski authored
The driver calls spi_get_device_match_data() and on its failure calls again parts of it: spi_get_device_id() and getting driver data. This is entirely redundant, because it is part of spi_get_device_match_data(). Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
-
Krzysztof Kozlowski authored
Use spi_get_device_match_data() helper to simplify a bit the driver. Signed-off-by:
-
Krzysztof Kozlowski authored
Use spi_get_device_match_data() helper to simplify a bit the driver. Signed-off-by:
-
Krzysztof Kozlowski authored
Use spi_get_device_match_data() helper to simplify a bit the driver. Signed-off-by:
-
Krzysztof Kozlowski authored
Use spi_get_device_match_data() helper to simplify a bit the driver. Signed-off-by:
-
Krzysztof Kozlowski authored
Use spi_get_device_match_data() helper to simplify a bit the driver. Signed-off-by:
-
Krzysztof Kozlowski authored
Use spi_get_device_match_data() helper to simplify a bit the driver. Signed-off-by:
-
Krzysztof Kozlowski authored
Use spi_get_device_match_data() helper to simplify a bit the driver. Signed-off-by:
-
Uwe Kleine-König authored
These drivers don't use the driver_data member of struct i2c_device_id, so don't explicitly initialize this member. This prepares putting driver_data in an anonymous union which requires either no initialization or named designators. But it's also a nice cleanup on its own. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@baylibre.com> Reviewed-by:
-
Antoni Pokusinski authored
This patch adds support for the integrated on-chip heater that is present on all the devices supported by this driver (si7020, si7021, si7013, th6). In order to configure the heater, the driver interacts with the following device registers: * User Register - the 2nd bit of this register is a "Heater Enable bit" (0 means that the heater is off, 1 means that it's on). * Heater Register - this register is present only on the si70xx devices and controls the current flowing through the heater. The 4 lower bits of this register can be assigned values from 0x0 to 0xF. Signed-off-by:
Antoni Pokusinski <apokusinski01@gmail.com> Link: https://lore.kernel.org/r/20240607141029.51744-1-apokusinski@o2.plSigned-off-by:
-
Jeff Johnson authored
make allmodconfig && make W=1 C=1 reports: WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/iio/adc/ingenic-adc.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/iio/adc/xilinx-ams.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/iio/buffer/kfifo_buf.o Add the missing invocations of the MODULE_DESCRIPTION() macro. Signed-off-by:
Jeff Johnson <quic_jjohnson@quicinc.com> Link: https://lore.kernel.org/r/20240607-md-drivers-iic-v1-1-9f9db6246083@quicinc.comSigned-off-by:
-
Erick Archer authored
It is preferred to use sizeof(*pointer) instead of sizeof(type) due to the type of the variable can change and one needs not change the former (unlike the latter). At the same time refactor the NULL comparison. This patch has no effect on runtime behavior. Signed-off-by:
Erick Archer <erick.archer@outlook.com> Link: https://lore.kernel.org/r/AS8PR02MB7237D024459C314CECE72EAF8BFE2@AS8PR02MB7237.eurprd02.prod.outlook.comSigned-off-by:
-
Aidan MacDonald authored
The AXP192 is identical to the AXP20x, except for the addition of two more GPIO ADC channels. Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by:
Aidan MacDonald <aidanmacdonald.0x0@gmail.com> Signed-off-by:
-
Josua Mayer authored
TI tla2021 is a limited single-channel variant of tla2024 which is similar enough to be easily supportable through the same driver. Add compatible string for tla2021 so boards may describe it in device-tree. Signed-off-by:
Josua Mayer <josua@solid-run.com> Acked-by:
Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20240602-cn9130-som-v6-3-89393e86d4c7@solid-run.comSigned-off-by:
-
Gustavo Ueti Fukunaga authored
Make use of iio_device_claim_direct_scoped() to make error handling more natural and simplify code. Co-developed-by:
Caio Dantas Simão Ugêda <caiodantas@usp.br> Signed-off-by:
Gustavo Ueti Fukunaga <gustavofukunaga@usp.br> Link: https://lore.kernel.org/r/20240527091942.53616-1-gustavofukunaga@usp.brSigned-off-by:
-
Val Packett authored
Allow using the mount-matrix device tree property to align the accelerometer relative to the whole device. Signed-off-by:
Val Packett <val@packett.cool> Link: https://lore.kernel.org/r/20240527080043.2709-1-val@packett.coolSigned-off-by:
-
Julien Stephan authored
Some callbacks from iio_info structure are accessed without any check, so if a driver doesn't implement them trying to access the corresponding sysfs entries produce a kernel oops such as: [ 2203.527791] Unable to handle kernel NULL pointer dereference at virtual address 00000000 when execute [...] [ 2203.783416] Call trace: [ 2203.783429] iio_read_channel_info_avail from dev_attr_show+0x18/0x48 [ 2203.789807] dev_attr_show from sysfs_kf_seq_show+0x90/0x120 [ 2203.794181] sysfs_kf_seq_show from seq_read_iter+0xd0/0x4e4 [ 2203.798555] seq_read_iter from vfs_read+0x238/0x2a0 [ 2203.802236] vfs_read from ksys_read+0xa4/0xd4 [ 2203.805385] ksys_read from ret_fast_syscall+0x0/0x54 [ 2203.809135] Exception stack(0xe0badfa8 to 0xe0badff0) [ 2203.812880] dfa0: 00000003 b6f10f80 00000003 b6eab000 00020000 00000000 [ 2203.819746] dfc0: 00000003 b6f10f80 7ff00000 00000003 00000003 00000000 00020000 00000000 [ 2203.826619] dfe0: b6e1bc88 bed80958 b6e1bc94 b6e1bcb0 [ 2203.830363] Code: bad PC value [ 2203.832695] ---[ end trace 0000000000000000 ]--- Reviewed-by:
Julien Stephan <jstephan@baylibre.com> Link: https://lore.kernel.org/r/20240530-iio-core-fix-segfault-v3-1-8b7cd2a03773@baylibre.comSigned-off-by:
-
- 08 Jun, 2024 2 commits
-
-
Bruna Bispo authored
This fixes a checkpatch warning by changing the struct attribute from __attribute__((__packed__)) to __packed. Signed-off-by:
Bruna Bispo <blbispo1@gmail.com> Link: https://lore.kernel.org/r/20240528143816.13409-1-blbispo1@gmail.comSigned-off-by:
-
Ramona Gradinariu authored
Add documentation for adis16480 driver which describes the driver device files and shows how the user may use the ABI for various scenarios (configuration, measurement, etc.). Signed-off-by:
Ramona Gradinariu <ramona.gradinariu@analog.com> Reviewed-by:
-
- 04 Jun, 2024 18 commits
-
-
Ramona Gradinariu authored
Add documentation for IIO interfacing tools describing the available tools which can be used to retrieve data from IIO sysfs. Reference this documentation in adis16475.rst Signed-off-by:
-
Ramona Gradinariu authored
The ADIS16545 and ADIS16547 are a complete inertial system that includes a triaxis gyroscope and a triaxis accelerometer. The serial peripheral interface (SPI) and register structure provide a simple interface for data collection and configuration control. These devices are similar to the ones already supported in the driver, with changes in the scales, timings and the max spi speed in burst mode. Also, they support delta angle and delta velocity readings in burst mode, for which support was added in the trigger handler. Co-developed-by:
-
Ramona Gradinariu authored
Add ADIS16545/47 compatibles. Each newly added device has a different angular velocity/linear acceleration scale combination, as follows: Accel dynamic range: - 8g: ADIS16545 - 40g: ADIS16547 Gyro dynamic range: - 125 deg/sec: ADIS1545-1, ADIS16547-1 - 450 deg/sec: ADIS1545-2, ADIS16547-2 - 2000 deg/sec: ADIS1545-3, ADIS16547-3 Signed-off-by:
-
Ramona Gradinariu authored
Add support for delta angle and delta velocity raw readings to adis16480 driver. The following devices do not support delta readings in burst mode: ADIS16375, ADIS16480, ADIS16485, ADIS16488, ADIS16490, ADIS16495-1, ADIS16495-2, ADIS16495-3, ADIS16497-1, ADIS16497-2, ADIS16497-3, thus they cannot be retrieved via the buffer interface. For these devices, the delta measurements are retrieved by performing normal register readings and are made available through the raw attributes of the specific channels. Signed-off-by:
-
Ramona Gradinariu authored
With this, we can pass the maxixum spi burst speed to the 'ADIS16480_DATA()' macro. This is in preparation to support new devices that have a different speed than the one used so far. Co-developed-by:
-
Ramona Gradinariu authored
Add support for ADIS1657X family devices in already exiting ADIS16475 driver. Signed-off-by:
Ramona Gradinariu <ramona.bolboaca13@gmail.com> Link: https://lore.kernel.org/r/20240527142618.275897-10-ramona.bolboaca13@gmail.comSigned-off-by:
-
Ramona Gradinariu authored
Add ADIS1657X family devices compatibles and specify the according maximum SPI baudrate. Similarly to other ADIS1650X devices, ADIS1657X supports sync-mode values [0,2]. Each newly added device has a different angular velocity/linear acceleration/ delta velocity scale combination, as follows: Accel dynamic range sensitivity: - 262144000 LSB/g: ADIS16575 - 52428800 LSB/g: ADIS16576, ADIS16577 Gyro dynamic range sensitivity: - 2621440 LSB/deg/sec: ADIS1575-2, ADIS1576-2, ADIS1577-2 - 655360 LSB/deg/sec: ADIS1575-3, ADIS1576-3, ADIS1577-3 Delta velocity sensitivity: - 2^15/100 LSB/m/sec: ADIS16575 - 2^15/125 LSB/m/sec: ADIS16576 - 2^15/400 LSB/m/sec: ADIS16577 Each ADIS1657X device supports FIFO usage and a sample-rate of 4.1KHz, meanwhile the already existing devices do not support FIFO usage and have a maximum sample-rate of 2.1KHz. Reviewed-by:
-
Ramona Gradinariu authored
Re-define ADIS16475_DATA such that it takes _burst_max_len, _burst_max_speed_hz and _has_fifo as parameters. Also, do a preparatory rename operation for ADIS16475_BURST32_MAX_DATA to ADIS16475_BURST32_MAX_DATA_NO_TS32 to be able to differentiate in the future between devices which are using 16-bit or 32-bit timestamp size in burst mode. Signed-off-by:
-
Ramona Gradinariu authored
Currently, adis library allows configuration only for edge interrupts, needed for data ready sampling. This patch removes the restriction for level interrupts for devices which have FIFO support. Furthermore, in case of devices which have FIFO support, devm_request_threaded_irq is used for interrupt allocation, to avoid flooding the processor with the FIFO watermark level interrupt, which is active until enough data has been read from the FIFO. Reviewed-by:
-
Ramona Gradinariu authored
Currently adis16475 supports a sample rate between 1900 and 2100 Hz. This patch changes the setting of sample rate from hardcoded values to a generic computation based on the internal clock frequency. This is a preparatory patch for adding support for adis1657x family devices which allow sample rates between 3900 and 4100 Hz. Reviewed-by:
-
Ramona Gradinariu authored
Create push single sample API reposnsible for pushing a single sample into the buffer. This is a preparation patch for FIFO support where more than one sample has to be pushed in the trigger handler. Reviewed-by:
-
Ramona Gradinariu authored
Add new API called devm_adis_setup_buffer_and_trigger_with_attrs() which also takes buffer attributes as a parameter. Rewrite devm_adis_setup_buffer_and_trigger() implementation such that it calls devm_adis_setup_buffer_and_trigger_with_attrs() with buffer attributes parameter NULL Reviewed-by:
-
Ramona Gradinariu authored
Add support for ADIS16501 device in already existing ADIS16475 driver. Reviewed-by:
-
Ramona Gradinariu authored
Add ADIS16501 compatible. Similarly to other ADIS1650X devices, ADIS16501 supports sync-mode values [0,2]. There are two differences between ADIS16501 and ADIS16477-2: - ADIS16501 does not support pulse sync mode - the delta velocity scale value is different Acked-by:
-
Julien Stephan authored
ad7380x(-4) parts are able to do oversampling to increase accuracy. This chips supports a normal oversampling mode and a rolling mode and also allows enabling and disabling extra resolution bits when oversampling is enabled. We have intentionally left out the rolling mode for now as there is not a compelling use case for it. User can process a captured data buffer to get the same effect. We are also currently not supporting changing the oversampling mode independently of the resolution bits. The resolution boost feature can only be enabled when oversampling is enabled and oversampling is not as useful without the resolution boost. So for now we consider the features tightly coupled. When oversampling is enabled, the resolution boost is enabled and when oversampling is disabled, the resolution boost is disabled. Since the resolution boost feature causes 16-bit chips to now have 18-bit data which means the storagebits has to change from 16 to 32 bits, we use the new ext_scan_type feature to allow changing the scan_type at runtime based on if the resolution boost is enabled or not. SPI message optimization has to be moved since now some of the xfer parameters change based on the resolution boost mode. A few neighboring comments are also fixed up while we are touching this code. Signed-off-by:
David Lechner <dlechner@baylibre.com> Signed-off-by:
-
David Lechner authored
This changes the AD7380 to use spi_optimize_message() to optimize buffered reads. This changes both direct reads and buffered reads to use the same spi_message. This has some (welcome) side effects. The first is that in buffered reads, the timestamp will now correspond to the same sample rather than the previous sample. The second is that direct reads now use the same SPI bus speed as buffered reads. This reduces CPU usage of the IRQ thread from around 25% to around 20% when sampling at 10 kHz on a ZedBoard. Signed-off-by:
-
David Lechner authored
This adds new fields to the iio_channel structure to support multiple scan types per channel. This is useful for devices that support multiple resolution modes or other modes that require different data formats of the raw data. To make use of this, drivers need to implement the new callback get_current_scan_type() to resolve the scan type for a given channel based on the current state of the driver. There is a new scan_type_ext field in the iio_channel structure that should be used to store the scan types for any channel that has more than one. There is also a new flag has_ext_scan_type that acts as a type discriminator for the scan_type/ext_scan_type union. A union is used so that we don't grow the size of the iio_channel structure and also makes it clear that scan_type and ext_scan_type are mutually exclusive. The buffer code is the only code in the IIO core code that is using the scan_type field. This patch updates the buffer code to use the new iio_channel_validate_scan_type() function to ensure it is returning the correct scan type for the current state of the device when reading the sysfs attributes. The buffer validation code is also update to validate any additional scan types that are set in the scan_type_ext field. Part of that code is refactored to a new function to avoid duplication. Some userspace tools may need to be updated to re-read the scan type after writing any other attribute. During testing, we noticed that we had to restart iiod to get it to re-read the scan type after enabling oversampling on the ad7380 driver. Signed-off-by:
-
David Lechner authored
By using struct iio_scan_type, we can simplify the code by removing lots of duplicate pointer dereferences. This make the code a bit easier to read. This also prepares for a future where channels may have more than one scan_type. Signed-off-by:
-
