When amt interface receives amt message, it tries to obtain amt private
data from sock.
If there is no amt private data, it frees an skb immediately.
After kfree_skb(), it increases the rx_dropped stats.
But in order to use rx_dropped, amt private data is needed.
So, it makes amt_rcv() to do not increase rx_dropped stats when it can
not obtain amt private data.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 1a1a0e80 ("amt: fix possible memory leak in amt_rcv()")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

It adds missing pskb_may_pull() in amt_update_handler() and
amt_multicast_data_handler().
And it fixes wrong parameter of pskb_may_pull() in
amt_advertisement_handler() and amt_membership_query_handler().
Reported-by: Jakub Kicinski <kuba@kernel.org>
Fixes: cbc21dc1 ("amt: add data plane of amt interface")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

There is a limitation in TI DP83867 PHY device where SGMII AN is only
triggered once after the device is booted up. Even after the PHY TPI is
down and up again, SGMII AN is not triggered and hence no new in-band
message from PHY to MAC side SGMII.

This could cause an issue during power up, when PHY is up prior to MAC.
At this condition, once MAC side SGMII is up, MAC side SGMII wouldn`t
receive new in-band message from TI PHY with correct link status, speed
and duplex info.

As suggested by TI, implemented a SW solution here to retrigger SGMII
Auto-Neg whenever there is a link change.

v2: Add Fixes tag in commit message.

Fixes: 2a10154a ("net: phy: dp83867: Add TI dp83867 phy")
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Sit, Michael Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220526090347.128742-1-tee.min.tan@linux.intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bpf and netfilter.

  Current release - new code bugs:

   - af_packet: make sure to pull the MAC header, avoid skb panic in GSO

   - ptp_clockmatrix: fix inverted logic in is_single_shot()

   - netfilter: flowtable: fix missing FLOWI_FLAG_ANYSRC flag

   - dt-bindings: net: adin: fix adi,phy-output-clock description syntax

   - wifi: iwlwifi: pcie: rename CAUSE macro, avoid MIPS build warning

  Previous releases - regressions:

   - Revert "net: af_key: add check for pfkey_broadcast in function
     pfkey_process"

   - tcp: fix tcp_mtup_probe_success vs wrong snd_cwnd

   - nf_tables: disallow non-stateful expression in sets earlier

   - nft_limit: clone packet limits' cost value

   - nf_tables: double hook unregistration in netns path

   - ping6: fix ping -6 with interface name

  Previous releases - always broken:

   - sched: fix memory barriers to prevent skbs from getting stuck in
     lockless qdiscs

   - neigh: set lower cap for neigh_managed_work rearming, avoid
     constantly scheduling the probe work

   - bpf: fix probe read error on big endian in ___bpf_prog_run()

   - amt: memory leak and error handling fixes

  Misc:

   - ipv6: expand & rename accept_unsolicited_na to accept_untracked_na"

* tag 'net-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (80 commits)
  net/af_packet: make sure to pull mac header
  net: add debug info to __skb_pull()
  net: CONFIG_DEBUG_NET depends on CONFIG_NET
  stmmac: intel: Add RPL-P PCI ID
  net: stmmac: use dev_err_probe() for reporting mdio bus registration failure
  tipc: check attribute length for bearer name
  ice: fix access-beyond-end in the switch code
  nfp: remove padding in nfp_nfdk_tx_desc
  ax25: Fix ax25 session cleanup problems
  net: usb: qmi_wwan: Add support for Cinterion MV31 with new baseline
  sfc/siena: fix wrong tx channel offset with efx_separate_tx_channels
  sfc/siena: fix considering that all channels have TX queues
  socket: Don't use u8 type in uapi socket.h
  net/sched: act_api: fix error code in tcf_ct_flow_table_fill_tuple_ipv6()
  net: ping6: Fix ping -6 with interface name
  macsec: fix UAF bug for real_dev
  octeontx2-af: fix error code in is_valid_offset()
  wifi: mac80211: fix use-after-free in chanctx code
  bonding: guard ns_targets by CONFIG_IPV6
  tcp: tcp_rtx_synack() can be called from process context
  ...

Commit cfc1d277 ("module: Move all into module/") changed the prefix
of the module param by moving/renaming files.  A later commit also moves
the module_param() into a different file, thereby changing the prefix
yet again.

This would break kernel cmdline compatibility and also userspace
compatibility at /sys/module/module/parameters/sig_enforce.

So, set the prefix back to "module.".

Fixes: cfc1d277 ("module: Move all into module/")
Link: https://lore.kernel.org/lkml/20220602034111.4163292-1-saravanak@google.com/
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Aaron Tomlin <atomlin@redhat.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull pci fixes from Bjorn Helgaas:

 - Revert brcmstb patches that broke booting on Raspberry Pi Compute
   Module 4 (Bjorn Helgaas)

 - Fix bridge_d3_blacklist[] error that overwrote the existing Gigabyte
   X299 entry instead of adding a new one (Bjorn Helgaas)

 - Update Lorenzo Pieralisi's email address in MAINTAINERS (Lorenzo
   Pieralisi)

* tag 'pci-v5.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  MAINTAINERS: Update Lorenzo Pieralisi's email address
  PCI/PM: Fix bridge_d3_blacklist[] Elo i2 overwrite of Gigabyte X299
  Revert "PCI: brcmstb: Split brcm_pcie_setup() into two funcs"
  Revert "PCI: brcmstb: Add mechanism to turn on subdev regulators"
  Revert "PCI: brcmstb: Add control of subdevice voltage regulators"
  Revert "PCI: brcmstb: Do not turn off WOL regulators on suspend"

Eric Dumazet says:

====================
net: af_packet: be careful when expanding mac header size

A recent regression in af_packet needed a preliminary debug patch,
which will presumably be useful for next bugs hunting.

The af_packet fix is to make sure MAC headers are contained in
skb linear part, as GSO stack requests.

v2: CONFIG_DEBUG_NET depends on CONFIG_NET to avoid compile
   errors found by kernel bots.
====================

Link: https://lore.kernel.org/r/20220602161859.2546399-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

GSO assumes skb->head contains link layer headers.

tun device in some case can provide base 14 bytes,
regardless of VLAN being used or not.

After blamed commit, we can end up setting a network
header offset of 18+, we better pull the missing
bytes to avoid a posible crash in GSO.

syzbot report was:
kernel BUG at include/linux/skbuff.h:2699!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 3601 Comm: syz-executor210 Not tainted 5.18.0-syzkaller-11338-g2c5ca23f #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__skb_pull include/linux/skbuff.h:2699 [inline]
RIP: 0010:skb_mac_gso_segment+0x48f/0x530 net/core/gro.c:136
Code: 00 48 c7 c7 00 96 d4 8a c6 05 cb d3 45 06 01 e8 26 bb d0 01 e9 2f fd ff ff 49 c7 c4 ea ff ff ff e9 f1 fe ff ff e8 91 84 19 fa <0f> 0b 48 89 df e8 97 44 66 fa e9 7f fd ff ff e8 ad 44 66 fa e9 48
RSP: 0018:ffffc90002e2f4b8 EFLAGS: 00010293
RAX: 0000000000000000 RBX: 0000000000000012 RCX: 0000000000000000
RDX: ffff88805bb58000 RSI: ffffffff8760ed0f RDI: 0000000000000004
RBP: 0000000000005dbc R08: 0000000000000004 R09: 0000000000000fe0
R10: 0000000000000fe4 R11: 0000000000000000 R12: 0000000000000fe0
R13: ffff88807194d780 R14: 1ffff920005c5e9b R15: 0000000000000012
FS:  000055555730f300(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000200015c0 CR3: 0000000071ff8000 CR4: 0000000000350ee0
Call Trace:
 <TASK>
 __skb_gso_segment+0x327/0x6e0 net/core/dev.c:3411
 skb_gso_segment include/linux/netdevice.h:4749 [inline]
 validate_xmit_skb+0x6bc/0xf10 net/core/dev.c:3669
 validate_xmit_skb_list+0xbc/0x120 net/core/dev.c:3719
 sch_direct_xmit+0x3d1/0xbe0 net/sched/sch_generic.c:327
 __dev_xmit_skb net/core/dev.c:3815 [inline]
 __dev_queue_xmit+0x14a1/0x3a00 net/core/dev.c:4219
 packet_snd net/packet/af_packet.c:3071 [inline]
 packet_sendmsg+0x21cb/0x5550 net/packet/af_packet.c:3102
 sock_sendmsg_nosec net/socket.c:714 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:734
 ____sys_sendmsg+0x6eb/0x810 net/socket.c:2492
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2546
 __sys_sendmsg net/socket.c:2575 [inline]
 __do_sys_sendmsg net/socket.c:2584 [inline]
 __se_sys_sendmsg net/socket.c:2582 [inline]
 __x64_sys_sendmsg+0x132/0x220 net/socket.c:2582
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7f4b95da06c9
Code: 28 c3 e8 4a 15 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffd7defc4c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007ffd7defc4f0 RCX: 00007f4b95da06c9
RDX: 0000000000000000 RSI: 0000000020000140 RDI: 0000000000000003
RBP: 0000000000000003 R08: bb1414ac00000050 R09: bb1414ac00000050
R10: 0000000000000004 R11: 0000000000000246 R12: 0000000000000000
R13: 00007ffd7defc4e0 R14: 00007ffd7defc4d8 R15: 00007ffd7defc4d4
 </TASK>

Fixes: dfed913e ("net/af_packet: add VLAN support for AF_PACKET SOCK_RAW GSO")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

While analyzing yet another syzbot report, I found the following
patch very useful. It allows to better understand what went wrong.

This debug info is only enabled if CONFIG_DEBUG_NET=y,
which is the case for syzbot builds.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

It makes little sense to debug networking stacks
if networking is not compiled in.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add PCI ID for Ethernet TSN Controller on RPL-P.
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Link: https://lore.kernel.org/r/20220602073507.3955721-1-michael.wei.hong.sit@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

I have a board where these two lines are always printed during boot:

   imx-dwmac 30bf0000.ethernet: Cannot register the MDIO bus
   imx-dwmac 30bf0000.ethernet: stmmac_dvr_probe: MDIO bus (id: 1) registration failed

It's perfectly fine, and the device is successfully (and silently, as
far as the console goes) probed later.

Use dev_err_probe() instead, which will demote these messages to debug
level (thus removing the alarming messages from the console) when the
error is -EPROBE_DEFER, and also has the advantage of including the
error code if/when it happens to be something other than -EPROBE_DEFER.

While here, add the missing \n to one of the format strings.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20220602074840.1143360-1-linux@rasmusvillemoes.dkSigned-off-by: Jakub Kicinski <kuba@kernel.org>

syzbot reported uninit-value:
=====================================================
BUG: KMSAN: uninit-value in string_nocheck lib/vsprintf.c:644 [inline]
BUG: KMSAN: uninit-value in string+0x4f9/0x6f0 lib/vsprintf.c:725
 string_nocheck lib/vsprintf.c:644 [inline]
 string+0x4f9/0x6f0 lib/vsprintf.c:725
 vsnprintf+0x2222/0x3650 lib/vsprintf.c:2806
 vprintk_store+0x537/0x2150 kernel/printk/printk.c:2158
 vprintk_emit+0x28b/0xab0 kernel/printk/printk.c:2256
 vprintk_default+0x86/0xa0 kernel/printk/printk.c:2283
 vprintk+0x15f/0x180 kernel/printk/printk_safe.c:50
 _printk+0x18d/0x1cf kernel/printk/printk.c:2293
 tipc_enable_bearer net/tipc/bearer.c:371 [inline]
 __tipc_nl_bearer_enable+0x2022/0x22a0 net/tipc/bearer.c:1033
 tipc_nl_bearer_enable+0x6c/0xb0 net/tipc/bearer.c:1042
 genl_family_rcv_msg_doit net/netlink/genetlink.c:731 [inline]

- Do sanity check the attribute length for TIPC_NLA_BEARER_NAME.
- Do not use 'illegal name' in printing message.

Reported-by: syzbot+e820fdc8ce362f2dea51@syzkaller.appspotmail.com
Fixes: cb30a633 ("tipc: refactor function tipc_enable_bearer()")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Link: https://lore.kernel.org/r/20220602063053.5892-1-hoang.h.le@dektech.com.auSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull ceph updates from Ilya Dryomov:
 "A big pile of assorted fixes and improvements for the filesystem with
  nothing in particular standing out, except perhaps that the fact that
  the MDS never really maintained atime was made official and thus it's
  no longer updated on the client either.

  We also have a MAINTAINERS update: Jeff is transitioning his
  filesystem maintainership duties to Xiubo"

* tag 'ceph-for-5.19-rc1' of https://github.com/ceph/ceph-client: (23 commits)
  MAINTAINERS: move myself from ceph "Maintainer" to "Reviewer"
  ceph: fix decoding of client session messages flags
  ceph: switch TASK_INTERRUPTIBLE to TASK_KILLABLE
  ceph: remove redundant variable ino
  ceph: try to queue a writeback if revoking fails
  ceph: fix statfs for subdir mounts
  ceph: fix possible deadlock when holding Fwb to get inline_data
  ceph: redirty the page for writepage on failure
  ceph: try to choose the auth MDS if possible for getattr
  ceph: disable updating the atime since cephfs won't maintain it
  ceph: flush the mdlog for filesystem sync
  ceph: rename unsafe_request_wait()
  libceph: use swap() macro instead of taking tmp variable
  ceph: fix statx AT_STATX_DONT_SYNC vs AT_STATX_FORCE_SYNC check
  ceph: no need to invalidate the fscache twice
  ceph: replace usage of found with dedicated list iterator variable
  ceph: use dedicated list iterator variable
  ceph: update the dlease for the hashed dentry when removing
  ceph: stop retrying the request when exceeding 256 times
  ceph: stop forwarding the request when exceeding 256 times
  ...

Merge tag 'livepatching-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching

Pull livepatching cleanup from Petr Mladek:

 - Remove duplicated livepatch code [Christophe]

* tag 'livepatching-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching:
  livepatch: Remove klp_arch_set_pc() and asm/livepatch.h

Pull printk fixup from Petr Mladek:

 - Revert inappropriate use of wake_up_interruptible_all() in printk()

* tag 'printk-for-5.19-fixup' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
  Revert "printk: wake up all waiters"

Pull memblock test suite updates from Mike Rapoport:
 "Comment updates for memblock test suite

  Update comments in the memblock tests so that they will have
  consistent style"

* tag 'memblock-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
  memblock tests: remove completed TODO item
  memblock tests: update style of comments for memblock_free_*() functions
  memblock tests: update style of comments for memblock_remove_*() functions
  memblock tests: update style of comments for memblock_reserve_*() functions
  memblock tests: update style of comments for memblock_add_*() functions

The "data->block[0]" variable comes from the user and is a number
between 0-255.  It needs to be capped to prevent writing beyond the end
of dma_buffer[].

Fixes: 5e9a97b1 ("i2c: ismt: Adding support for I2C_SMBUS_BLOCK_PROC_CALL")
Reported-and-tested-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Global `-Warray-bounds` enablement revealed some problems, one of
which is the way we define and use AQC rules messages.
In fact, they have a shared header, followed by the actual message,
which can be of one of several different formats. So it is
straightforward enough to define that header as a separate struct
and then embed it into message structures as needed, but currently
all the formats reside in one union coupled with the header. Then,
the code allocates only the memory needed for a particular message
format, leaving the union potentially incomplete.
There are no actual reads or writes beyond the end of an allocated
chunk, but at the same time, the whole implementation is fragile and
backed by an equilibrium rather than strong type and memory checks.

Define the structures the other way around: one for the common
header and the rest for the actual formats with the header embedded.
There are no places where several union members would be used at the
same time anyway. This allows to use proper struct_size() and let
the compiler know what is going to be done.
Finally, unsilence `-Warray-bounds` back for ice_switch.c.

Other little things worth mentioning:
* &ice_sw_rule_vsi_list_query is not used anywhere, remove it. It's
  weird anyway to talk to hardware with purely kernel types
  (bitmaps);
* expand the ICE_SW_RULE_*_SIZE() macros to pass a structure
  variable name to struct_size() to let it do strict typechecking;
* rename ice_sw_rule_lkup_rx_tx::hdr to ::hdr_data to keep ::hdr
  for the header structure to have the same name for it constistenly
  everywhere;
* drop the duplicate of %ICE_SW_RULE_RX_TX_NO_HDR_SIZE residing in
  ice_switch.h.

Fixes: 9daf8208 ("ice: Add support for switch filter programming")
Fixes: 66486d89 ("ice: replace single-element array used for C struct hack")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Acked-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220601105924.2841410-1-alexandr.lobakin@intel.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

NFDK firmware supports 48-bit dma addressing and
parses 16 high bits of dma addresses.

In nfp_nfdk_tx_desc, dma related structure and tso
related structure are union. When "mss" be filled
with nonzero value due to enable tso, the memory used
by "padding" may be also filled. Then, firmware may
parse wrong dma addresses which causes TX watchdog
timeout problem.

This patch removes padding and unifies the dma_addr_hi
bits with the one in firmware. nfp_nfdk_tx_desc_set_dma_addr
is also added to match this change.

Fixes: c10d12e3 ("nfp: add support for NFDK data path")
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220601083449.50556-1-simon.horman@corigine.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

There are session cleanup problems in ax25_release() and
ax25_disconnect(). If we setup a session and then disconnect,
the disconnected session is still in "LISTENING" state that
is shown below.

Active AX.25 sockets
Dest       Source     Device  State        Vr/Vs    Send-Q  Recv-Q
DL9SAU-4   DL9SAU-3   ???     LISTENING    000/000  0       0
DL9SAU-3   DL9SAU-4   ???     LISTENING    000/000  0       0

The first reason is caused by del_timer_sync() in ax25_release().
The timers of ax25 are used for correct session cleanup. If we use
ax25_release() to close ax25 sessions and ax25_dev is not null,
the del_timer_sync() functions in ax25_release() will execute.
As a result, the sessions could not be cleaned up correctly,
because the timers have stopped.

In order to solve this problem, this patch adds a device_up flag
in ax25_dev in order to judge whether the device is up. If there
are sessions to be cleaned up, the del_timer_sync() in
ax25_release() will not execute. What's more, we add ax25_cb_del()
in ax25_kill_by_device(), because the timers have been stopped
and there are no functions that could delete ax25_cb if we do not
call ax25_release(). Finally, we reorder the position of
ax25_list_lock in ax25_cb_del() in order to synchronize among
different functions that call ax25_cb_del().

The second reason is caused by improper check in ax25_disconnect().
The incoming ax25 sessions which ax25->sk is null will close
heartbeat timer, because the check "if(!ax25->sk || ..)" is
satisfied. As a result, the session could not be cleaned up properly.

In order to solve this problem, this patch changes the improper
check to "if(ax25->sk && ..)" in ax25_disconnect().

What`s more, the ax25_disconnect() may be called twice, which is
not necessary. For example, ax25_kill_by_device() calls
ax25_disconnect() and sets ax25->state to AX25_STATE_0, but
ax25_release() calls ax25_disconnect() again.

In order to solve this problem, this patch add a check in
ax25_release(). If the flag of ax25->sk equals to SOCK_DEAD,
the ax25_disconnect() in ax25_release() should not be executed.

Fixes: 82e31755 ("ax25: Fix UAF bugs in ax25 timers")
Fixes: 8a367e74 ("ax25: Fix segfault after sock connection timeout")
Reported-and-tested-by: Thomas Osterried <thomas@osterried.de>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220530152158.108619-1-duoming@zju.edu.cnSigned-off-by: Paolo Abeni <pabeni@redhat.com>

A rare BUG_ON triggered in assoc_array_gc:

    [3430308.818153] kernel BUG at lib/assoc_array.c:1609!

Which corresponded to the statement currently at line 1593 upstream:

    BUG_ON(assoc_array_ptr_is_meta(p));

Using the data from the core dump, I was able to generate a userspace
reproducer[1] and determine the cause of the bug.

[1]: https://github.com/brenns10/kernel_stuff/tree/master/assoc_array_gc

After running the iterator on the entire branch, an internal tree node
looked like the following:

    NODE (nr_leaves_on_branch: 3)
      SLOT [0] NODE (2 leaves)
      SLOT [1] NODE (1 leaf)
      SLOT [2..f] NODE (empty)

In the userspace reproducer, the pr_devel output when compressing this
node was:

    -- compress node 0x5607cc089380 --
    free=0, leaves=0
    [0] retain node 2/1 [nx 0]
    [1] fold node 1/1 [nx 0]
    [2] fold node 0/1 [nx 2]
    [3] fold node 0/2 [nx 2]
    [4] fold node 0/3 [nx 2]
    [5] fold node 0/4 [nx 2]
    [6] fold node 0/5 [nx 2]
    [7] fold node 0/6 [nx 2]
    [8] fold node 0/7 [nx 2]
    [9] fold node 0/8 [nx 2]
    [10] fold node 0/9 [nx 2]
    [11] fold node 0/10 [nx 2]
    [12] fold node 0/11 [nx 2]
    [13] fold node 0/12 [nx 2]
    [14] fold node 0/13 [nx 2]
    [15] fold node 0/14 [nx 2]
    after: 3

At slot 0, an internal node with 2 leaves could not be folded into the
node, because there was only one available slot (slot 0). Thus, the
internal node was retained. At slot 1, the node had one leaf, and was
able to be folded in successfully. The remaining nodes had no leaves,
and so were removed. By the end of the compression stage, there were 14
free slots, and only 3 leaf nodes. The tree was ascended and then its
parent node was compressed. When this node was seen, it could not be
folded, due to the internal node it contained.

The invariant for compression in this function is: whenever
nr_leaves_on_branch < ASSOC_ARRAY_FAN_OUT, the node should contain all
leaf nodes. The compression step currently cannot guarantee this, given
the corner case shown above.

To fix this issue, retry compression whenever we have retained a node,
and yet nr_leaves_on_branch < ASSOC_ARRAY_FAN_OUT. This second
compression will then allow the node in slot 1 to be folded in,
satisfying the invariant. Below is the output of the reproducer once the
fix is applied:

    -- compress node 0x560e9c562380 --
    free=0, leaves=0
    [0] retain node 2/1 [nx 0]
    [1] fold node 1/1 [nx 0]
    [2] fold node 0/1 [nx 2]
    [3] fold node 0/2 [nx 2]
    [4] fold node 0/3 [nx 2]
    [5] fold node 0/4 [nx 2]
    [6] fold node 0/5 [nx 2]
    [7] fold node 0/6 [nx 2]
    [8] fold node 0/7 [nx 2]
    [9] fold node 0/8 [nx 2]
    [10] fold node 0/9 [nx 2]
    [11] fold node 0/10 [nx 2]
    [12] fold node 0/11 [nx 2]
    [13] fold node 0/12 [nx 2]
    [14] fold node 0/13 [nx 2]
    [15] fold node 0/14 [nx 2]
    internal nodes remain despite enough space, retrying
    -- compress node 0x560e9c562380 --
    free=14, leaves=1
    [0] fold node 2/15 [nx 0]
    after: 3

Changes
=======
DH:
 - Use false instead of 0.
 - Reorder the inserted lines in a couple of places to put retained before
   next_slot.

ver #2)
 - Fix typo in pr_devel, correct comparison to "<="

Fixes: 3cb98950 ("Add a generic associative array implementation.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Andrew Morton <akpm@linux-foundation.org>
cc: keyrings@vger.kernel.org
Link: https://lore.kernel.org/r/20220511225517.407935-1-stephen.s.brennan@oracle.com/ # v1
Link: https://lore.kernel.org/r/20220512215045.489140-1-stephen.s.brennan@oracle.com/ # v2
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Adding support for Cinterion device MV31 with Qualcomm
new baseline. Use different PIDs to separate it from
previous base line products.
All interfaces settings keep same as previous.

T:  Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  7 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1e2d ProdID=00b9 Rev=04.14
S:  Manufacturer=Cinterion
S:  Product=Cinterion PID 0x00B9 USB Mobile Broadband
S:  SerialNumber=90418e79
C:  #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20220601040531.6016-1-slark_xiao@163.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Saeed Mahameed says:

====================
mlx5 fixes 2022-05-31

This series provides bug fixes to mlx5 driver.
Please pull and let me know if there is any problem.

* tag 'mlx5-fixes-2022-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
  net/mlx5: Fix mlx5_get_next_dev() peer device matching
  net/mlx5e: Update netdev features after changing XDP state
  net/mlx5: correct ECE offset in query qp output
  net/mlx5e: Disable softirq in mlx5e_activate_rq to avoid race condition
  net/mlx5: CT: Fix header-rewrite re-use for tupels
  net/mlx5e: TC NIC mode, fix tc chains miss table
  net/mlx5: Don't use already freed action pointer
====================

Link: https://lore.kernel.org/r/20220531205447.99236-1-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Íñigo Huguet says:

====================
sfc/siena: fix some efx_separate_tx_channels errors

Trying to load sfc driver with modparam efx_separate_tx_channels=1
resulted in errors during initialization and not being able to use the
NIC. This patches fix a few bugs and make it work again.

This has been already done for sfc, do it also for sfc_siena.
====================

Link: https://lore.kernel.org/r/20220601063603.15362-1-ihuguet@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

tx_channel_offset is calculated in efx_allocate_msix_channels, but it is
also calculated again in efx_set_channels because it was originally done
there, and when efx_allocate_msix_channels was introduced it was
forgotten to be removed from efx_set_channels.

Moreover, the old calculation is wrong when using
efx_separate_tx_channels because now we can have XDP channels after the
TX channels, so n_channels - n_tx_channels doesn't point to the first TX
channel.

Remove the old calculation from efx_set_channels, and add the
initialization of this variable if MSI or legacy interrupts are used,
next to the initialization of the rest of the related variables, where
it was missing.

This has been already done for sfc, do it also for sfc_siena.

Fixes: 3990a8ff ("sfc: allocate channels for XDP tx queues")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Normally, all channels have RX and TX queues, but this is not true if
modparam efx_separate_tx_channels=1 is used. In that cases, some
channels only have RX queues and others only TX queues (or more
preciselly, they have them allocated, but not initialized).

Fix efx_channel_has_tx_queues to return the correct value for this case
too.

This has been already done for sfc, do it also for sfc_siena.

Messages shown at probe time before the fix:
 sfc 0000:03:00.0 ens6f0np0: MC command 0x82 inlen 544 failed rc=-22 (raw=0) arg=0
 ------------[ cut here ]------------
 netdevice: ens6f0np0: failed to initialise TXQ -1
 WARNING: CPU: 1 PID: 626 at drivers/net/ethernet/sfc/ef10.c:2393 efx_ef10_tx_init+0x201/0x300 [sfc]
 [...] stripped
 RIP: 0010:efx_ef10_tx_init+0x201/0x300 [sfc]
 [...] stripped
 Call Trace:
  efx_init_tx_queue+0xaa/0xf0 [sfc]
  efx_start_channels+0x49/0x120 [sfc]
  efx_start_all+0x1f8/0x430 [sfc]
  efx_net_open+0x5a/0xe0 [sfc]
  __dev_open+0xd0/0x190
  __dev_change_flags+0x1b3/0x220
  dev_change_flags+0x21/0x60
 [...] stripped

Messages shown at remove time before the fix:
 sfc 0000:03:00.0 ens6f0np0: failed to flush 10 queues
 sfc 0000:03:00.0 ens6f0np0: failed to flush queues

Fixes: 8700aff0 ("sfc: fix channel allocation with brute force")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Tested-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Steffen Klassert says:

====================
ipsec 2022-06-01

1) Revert "net: af_key: add check for pfkey_broadcast in function pfkey_process"
   From Michal Kubecek.

2) Don't set IPv4 DF bit when encapsulating IPv6 frames below 1280 bytes.
   From Maciej Żenczykowski.

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
  xfrm: do not set IPv4 DF flag when encapsulating IPv6 frames <= 1280 bytes.
  Revert "net: af_key: add check for pfkey_broadcast in function pfkey_process"
====================

Link: https://lore.kernel.org/r/20220601103349.2297361-1-steffen.klassert@secunet.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Kalle Valo says:

====================
wireless fixes for v5.19

First set of fixes for v5.19. Build fixes for iwlwifi and libertas, a
scheduling while atomic fix for rtw88 and use-after-free fix for
mac80211.

* tag 'wireless-2022-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
  wifi: mac80211: fix use-after-free in chanctx code
  wifi: rtw88: add a work to correct atomic scheduling warning of ::set_tim
  wifi: iwlwifi: pcie: rename CAUSE macro
  wifi: libertas: use variable-size data in assoc req/resp cmd
====================

Link: https://lore.kernel.org/r/20220601110741.90B28C385A5@smtp.kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull more xfs updates from Dave Chinner:
 "This update is largely bug fixes and cleanups for all the code merged
  in the first pull request. The majority of them are to the new logged
  attribute code, but there are also a couple of fixes for other log
  recovery and memory leaks that have recently been found.

  Summary:

   - fix refcount leak in xfs_ifree()

   - fix xfs_buf_cancel structure leaks in log recovery

   - fix dquot leak after failed quota check

   - fix a couple of problematic ASSERTS

   - fix small aim7 perf regression in from new btree sibling validation

   - clean up log incompat feature marking for new logged attribute
     feature

   - disallow logged attributes on legacy V4 filesystem formats.

   - fix da state leak when freeing attr intents

   - improve validation of the attr log items in recovery

   - use slab caches for commonly used attr structures

   - fix leaks of attr name/value buffer and reduce copying overhead
     during intent logging

   - remove some dead debug code from log recovery"

* tag 'xfs-5.19-for-linus-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (33 commits)
  xfs: fix xfs_ifree() error handling to not leak perag ref
  xfs: move xfs_attr_use_log_assist usage out of libxfs
  xfs: move xfs_attr_use_log_assist out of xfs_log.c
  xfs: warn about LARP once per mount
  xfs: implement per-mount warnings for scrub and shrink usage
  xfs: don't log every time we clear the log incompat flags
  xfs: convert buf_cancel_table allocation to kmalloc_array
  xfs: don't leak xfs_buf_cancel structures when recovery fails
  xfs: refactor buffer cancellation table allocation
  xfs: don't leak btree cursor when insrec fails after a split
  xfs: purge dquots after inode walk fails during quotacheck
  xfs: assert in xfs_btree_del_cursor should take into account error
  xfs: don't assert fail on perag references on teardown
  xfs: avoid unnecessary runtime sibling pointer endian conversions
  xfs: share xattr name and value buffers when logging xattr updates
  xfs: do not use logged xattr updates on V4 filesystems
  xfs: Remove duplicate include
  xfs: reduce IOCB_NOWAIT judgment for retry exclusive unaligned DIO
  xfs: Remove dead code
  xfs: fix typo in comment
  ...

Use plain 255 instead, which also avoid introducing an additional header
dependency on <linux/types.h>

Fixes: 26859240 ("txhash: Add socket option to control TX hash rethink behavior")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20220531094345.13801-1-tklauser@distanz.chSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull RTC updates from Alexandre Belloni:
 "A new driver represents the bulk of the changes and then we get the
  usual small fixes.

  New driver:

   - Renesas RZN1 rtc

  Drivers:

   - sun6i: Add nvmem support"

* tag 'rtc-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
  rtc: mxc: Silence a clang warning
  rtc: rzn1: Fix a variable type
  rtc: rzn1: Fix error code in probe
  rtc: rzn1: Avoid mixing variables
  rtc: ftrtc010: Fix error handling in ftrtc010_rtc_probe
  rtc: mt6397: check return value after calling platform_get_resource()
  rtc: rzn1: fix platform_no_drv_owner.cocci warning
  rtc: gamecube: Add missing iounmap in gamecube_rtc_read_offset_from_sram
  rtc: meson: Fix email address in MODULE_AUTHOR
  rtc: simplify the return expression of rx8025_set_offset()
  rtc: pcf85063: Add a compatible entry for pca85073a
  dt-binding: pcf85063: Add an entry for pca85073a
  MAINTAINERS: Add myself as maintainer of the RZN1 RTC driver
  rtc: rzn1: Add oscillator offset support
  rtc: rzn1: Add alarm support
  rtc: rzn1: Add new RTC driver
  dt-bindings: rtc: rzn1: Describe the RZN1 RTC
  rtc: sun6i: Add NVMEM provider

Pull i3c updates from Alexandre Belloni:
 "Only clean ups and no functional change this cycle. A couple of yaml
  conversions of the DT bindings, and a couple of code cleanups"

* tag 'i3c/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
  MAINTAINERS: rectify entries for some i3c drivers after dt conversion
  i3c: master: svc: fix returnvar.cocci warning
  i3c/master: simplify the return expression of i3c_hci_remove()
  dt-bindings: i3c: Convert snps,dw-i3c-master to DT schema
  dt-bindings: i3c: Convert cdns,i3c-master to DT schema

Merge tag 'for-5.19/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - Fix DM core's dm_table_supports_poll to return false if target has no
   data devices.

 - Fix DM verity target so that it cannot be switched to a different DM
   target type (e.g. dm-linear) via DM table reload.

* tag 'for-5.19/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm verity: set DM_TARGET_IMMUTABLE feature flag
  dm table: fix dm_table_supports_poll to return false if no data devices

Change the of_device_get_match_data() cast to (uintptr_t)
to silence the following clang warning:

drivers/rtc/rtc-mxc.c:315:19: warning: cast to smaller integer type 'enum imx_rtc_type' from 'const void *' [-Wvoid-pointer-to-enum-cast]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: ba7aa630 ("rtc: mxc: use of_device_get_match_data")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220526011459.1167197-1-festevam@gmail.com

Pull power supply and reset updates from Sebastian Reichel:
 "Not much from the power-supply subsystem this time around, since I was
  busy most of the cycle. This also contains some fixes that I
  originally planned to send for 5.18. Apart from this there is nothing
  noteworthy.

  Power-supply core:

   - init power_supply_info struct to zero

  Drivers:

   - bq27xxx: expose data for uncalibrated battery

   - bq24190-charger: use pm_runtime_resume_and_get

   - ab8500_fg: allocate wq in probe

   - axp288_fuel_gauge: drop BIOS version from 'T3 MRD' quirk

   - axp288_fuel_gauge: modify 'T3 MRD' quirk to also fix 'One Mix 1'"

* tag 'for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
  power: supply: bq24190_charger: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
  power: supply: bq27xxx: expose battery data when CI=1
  power: supply: ab8500_fg: Allocate wq in probe
  power: supply: axp288_fuel_gauge: Drop BIOS version check from "T3 MRD" DMI quirk
  power: supply: axp288_fuel_gauge: Fix battery reporting on the One Mix 1
  power: supply: core: Initialize struct to zero

Pull watchdog updates from Wim Van Sebroeck:

 - Add MediaTek MT8186 support

 - Add Mediatek MT7986 reset-controller support

 - Add i.MX93 support

 - Add watchdog driver for Sunplus SP7021

 - Add SC8180X and SC8280XP compatibles

 - Add Renesas RZ/N1 Watchdog driver and support for RZ/N1

 - rzg2l_wdt improvements and fixes

 - Several other improvements and fixes

* tag 'linux-watchdog-5.19-rc1' of git://www.linux-watchdog.org/linux-watchdog: (38 commits)
  watchdog: ts4800_wdt: Fix refcount leak in ts4800_wdt_probe
  dt-bindings: watchdog: renesas,wdt: R-Car V3U is R-Car Gen4
  watchdog: Add Renesas RZ/N1 Watchdog driver
  dt-bindings: watchdog: renesas,wdt: Add support for RZ/N1
  watchdog: wdat_wdt: Stop watchdog when uninstalling module
  watchdog: wdat_wdt: Stop watchdog when rebooting the system
  watchdog: wdat_wdt: Using the existing function to check parameter timeout
  dt-bindings: watchdog: da9062: add watchdog timeout mode
  dt-bindings: watchdog: renesas,wdt: Document RZ/G2UL SoC
  watchdog: iTCO_wdt: Using existing macro define covers more scenarios
  watchdog: rti-wdt: Fix pm_runtime_get_sync() error checking
  dt-bindings: watchdog: Add SC8180X and SC8280XP compatibles
  watchdog: rti_wdt: Fix calculation and evaluation of preset heartbeat
  dt-bindings: watchdog: uniphier: Use unevaluatedProperties
  watchdog: sp805: disable watchdog on remove
  watchdog: da9063: optionally disable watchdog during suspend
  dt-bindings: mfd: da9063: watchdog: add suspend disable option
  dt-bindings: watchdog: sunxi: clarify clock support
  dt-bindings: watchdog: sunxi: fix F1C100s compatible
  watchdog: Add watchdog driver for Sunplus SP7021
  ...

Pull vfio updates from Alex Williamson:

 - Improvements to mlx5 vfio-pci variant driver, including support for
   parallel migration per PF (Yishai Hadas)

 - Remove redundant iommu_present() check (Robin Murphy)

 - Ongoing refactoring to consolidate the VFIO driver facing API to use
   vfio_device (Jason Gunthorpe)

 - Use drvdata to store vfio_device among all vfio-pci and variant
   drivers (Jason Gunthorpe)

 - Remove redundant code now that IOMMU core manages group DMA ownership
   (Jason Gunthorpe)

 - Remove vfio_group from external API handling struct file ownership
   (Jason Gunthorpe)

 - Correct typo in uapi comments (Thomas Huth)

 - Fix coccicheck detected deadlock (Wan Jiabing)

 - Use rwsem to remove races and simplify code around container and kvm
   association to groups (Jason Gunthorpe)

 - Harden access to devices in low power states and use runtime PM to
   enable d3cold support for unused devices (Abhishek Sahu)

 - Fix dma_owner handling of fake IOMMU groups (Jason Gunthorpe)

 - Set driver_managed_dma on vfio-pci variant drivers (Jason Gunthorpe)

 - Pass KVM pointer directly rather than via notifier (Matthew Rosato)

* tag 'vfio-v5.19-rc1' of https://github.com/awilliam/linux-vfio: (38 commits)
  vfio: remove VFIO_GROUP_NOTIFY_SET_KVM
  vfio/pci: Add driver_managed_dma to the new vfio_pci drivers
  vfio: Do not manipulate iommu dma_owner for fake iommu groups
  vfio/pci: Move the unused device into low power state with runtime PM
  vfio/pci: Virtualize PME related registers bits and initialize to zero
  vfio/pci: Change the PF power state to D0 before enabling VFs
  vfio/pci: Invalidate mmaps and block the access in D3hot power state
  vfio: Change struct vfio_group::container_users to a non-atomic int
  vfio: Simplify the life cycle of the group FD
  vfio: Fully lock struct vfio_group::container
  vfio: Split up vfio_group_get_device_fd()
  vfio: Change struct vfio_group::opened from an atomic to bool
  vfio: Add missing locking for struct vfio_group::kvm
  kvm/vfio: Fix potential deadlock problem in vfio
  include/uapi/linux/vfio.h: Fix trivial typo - _IORW should be _IOWR instead
  vfio/pci: Use the struct file as the handle not the vfio_group
  kvm/vfio: Remove vfio_group from kvm
  vfio: Change vfio_group_set_kvm() to vfio_file_set_kvm()
  vfio: Change vfio_external_check_extension() to vfio_file_enforced_coherent()
  vfio: Remove vfio_external_group_match_file()
  ...

Commit 4bd69ecf ("dt-bindings: i3c: Convert cdns,i3c-master to DT
schema") and commit 6742ca62 ("dt-bindings: i3c: Convert
snps,dw-i3c-master to DT schema") convert some i3c dt-bindings to yaml,
but miss to adjust its reference in MAINTAINERS.

Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about
broken references.

Repair these file references in I3C DRIVER FOR CADENCE I3C MASTER IP and
I3C DRIVER FOR SYNOPSYS DESIGNWARE.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220601074212.19984-1-lukas.bulwahn@gmail.com

Pull more erofs updates from Gao Xiang:
 "This is a follow-up to the main updates, including some fixes of
  fscache mode related to compressed inodes and a cachefiles tracepoint.
  There is also a patch to fix an unexpected decompression strategy
  change due to a cleanup in the past. All the fixes are quite small.

  Apart from these, documentation is also updated for a better
  description of recent new features.

  In addition, this has some trivial cleanups without actual code logic
  changes, so I could have a more recent codebase to work on folios and
  avoiding the PG_error page flag for the next cycle.

  Summary:

   - Leave compressed inodes unsupported in fscache mode for now

   - Avoid crash when using tracepoint cachefiles_prep_read

   - Fix `backmost' behavior due to a recent cleanup

   - Update documentation for better description of recent new features

   - Several decompression cleanups w/o logical change"

* tag 'erofs-for-5.19-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
  erofs: fix 'backmost' member of z_erofs_decompress_frontend
  erofs: simplify z_erofs_pcluster_readmore()
  erofs: get rid of label `restart_now'
  erofs: get rid of `struct z_erofs_collection'
  erofs: update documentation
  erofs: fix crash when enable tracepoint cachefiles_prep_read
  erofs: leave compressed inodes unsupported in fscache mode for now