ct_label 0 is a default label each flow has and therefore
there can be rules that match on ct_label=0 without a prior
rule that set the ct_label to this value.

The ct_label value is not used directly in the HW rules and
instead it is mapped to some id within a defined range and this
id is used to set and match the metadata register which carries
the ct_label.

If we have a rule that matches on ct_label=0, the hw rule will
perform matching on a value that is != 0 because of the mapping
from label to id. Since the metadata register default value is
0 and it was never set before to anything else by an action that
sets the ct_label, there will always be a mismatch between that
register and the value in the rule.

To support such rule, a forced mapping of ct_label 0 to id=0
is done so that it will match the metadata register default
value of 0.

Fixes: 54b154ec ("net/mlx5e: CT: Map 128 bits labels to 32 bit map ID")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Commit 924a9bc3 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
added a call to dev_parse_header_protocol() but mac_header is not yet set.

This means that eth_hdr() reads complete garbage, and syzbot complained about it [1]

This patch resets mac_header earlier, to get more coverage about this change.

Audit of virtio_net_hdr_to_skb() callers shows that this change should be safe.

[1]

BUG: KASAN: use-after-free in eth_header_parse_protocol+0xdc/0xe0 net/ethernet/eth.c:282
Read of size 2 at addr ffff888017a6200b by task syz-executor313/8409

CPU: 1 PID: 8409 Comm: syz-executor313 Not tainted 5.12.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:79 [inline]
 dump_stack+0x141/0x1d7 lib/dump_stack.c:120
 print_address_description.constprop.0.cold+0x5b/0x2f8 mm/kasan/report.c:232
 __kasan_report mm/kasan/report.c:399 [inline]
 kasan_report.cold+0x7c/0xd8 mm/kasan/report.c:416
 eth_header_parse_protocol+0xdc/0xe0 net/ethernet/eth.c:282
 dev_parse_header_protocol include/linux/netdevice.h:3177 [inline]
 virtio_net_hdr_to_skb.constprop.0+0x99d/0xcd0 include/linux/virtio_net.h:83
 packet_snd net/packet/af_packet.c:2994 [inline]
 packet_sendmsg+0x2325/0x52b0 net/packet/af_packet.c:3031
 sock_sendmsg_nosec net/socket.c:654 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:674
 sock_no_sendpage+0xf3/0x130 net/core/sock.c:2860
 kernel_sendpage.part.0+0x1ab/0x350 net/socket.c:3631
 kernel_sendpage net/socket.c:3628 [inline]
 sock_sendpage+0xe5/0x140 net/socket.c:947
 pipe_to_sendpage+0x2ad/0x380 fs/splice.c:364
 splice_from_pipe_feed fs/splice.c:418 [inline]
 __splice_from_pipe+0x43e/0x8a0 fs/splice.c:562
 splice_from_pipe fs/splice.c:597 [inline]
 generic_splice_sendpage+0xd4/0x140 fs/splice.c:746
 do_splice_from fs/splice.c:767 [inline]
 do_splice+0xb7e/0x1940 fs/splice.c:1079
 __do_splice+0x134/0x250 fs/splice.c:1144
 __do_sys_splice fs/splice.c:1350 [inline]
 __se_sys_splice fs/splice.c:1332 [inline]
 __x64_sys_splice+0x198/0x250 fs/splice.c:1332
 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46

Fixes: 924a9bc3 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Balazs Nemeth <bnemeth@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should not be advertising EEE for modes that we do not support,
correct that oversight by looking at the PHY device supported linkmodes.

Fixes: 99cec8a4 ("net: phy: broadcom: Allow enabling or disabling of EEE")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A merge hint message needs some time to process before the merged
flow actually reaches the firmware, during which we may get duplicate
merge hints if there're more than one packet that hit the pre-merged
flow. And processing duplicate merge hints will cost extra host_ctx's
which are a limited resource.

Avoid the duplicate merge by using hash table to store the sub_flows
to be merged.

Fixes: 8af56f40 ("nfp: flower: offload merge flows")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the mentioned helper can end-up freeing the socket wmem
without waking-up any processes waiting for more write memory.

If the partially orphaned skb is attached to an UDP (or raw) socket,
the lack of wake-up can hang the user-space.

Even for TCP sockets not calling the sk destructor could have bad
effects on TSQ.

Address the issue using skb_orphan to release the sk wmem before
setting the new sock_efree destructor. Additionally bundle the
whole ownership update in a new helper, so that later other
potential users could avoid duplicate code.

v1 -> v2:
 - use skb_orphan() instead of sort of open coding it (Eric)
 - provide an helper for the ownership change (Eric)

Fixes: f6ba8d33 ("netem: fix skb_orphan_partial()")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sch_htb: fix null pointer dereference on a null new_q

Currently if new_q is null, the null new_q pointer will be
dereference when 'q->offload' is true. Fix this by adding
a braces around htb_parent_to_leaf_offload() to avoid it.

Addresses-Coverity: ("Dereference after null check")
Fixes: d03b195b ("sch_htb: Hierarchical QoS hardware offload")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qrtr_tx_wait does not check for radix_tree_insert failure, causing
the 'flow' object to be unreferenced after qrtr_tx_wait return. Fix
that by releasing flow on radix_tree_insert failure.

Fixes: 5fdeb0d3 ("net: qrtr: Implement outgoing flow control")
Reported-by: syzbot+739016799a89c530b32a@syzkaller.appspotmail.com
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, action creation using ACT API in replace mode is buggy.
When invoking for non-existent action index 42,

	tc action replace action bpf obj foo.o sec <xyz> index 42

kernel creates the action, fills up the netlink response, and then just
deletes the action after notifying userspace.

	tc action show action bpf

doesn't list the action.

This happens due to the following sequence when ovr = 1 (replace mode)
is enabled:

tcf_idr_check_alloc is used to atomically check and either obtain
reference for existing action at index, or reserve the index slot using
a dummy entry (ERR_PTR(-EBUSY)).

This is necessary as pointers to these actions will be held after
dropping the idrinfo lock, so bumping the reference count is necessary
as we need to insert the actions, and notify userspace by dumping their
attributes. Finally, we drop the reference we took using the
tcf_action_put_many call in tcf_action_add. However, for the case where
a new action is created due to free index, its refcount remains one.
This when paired with the put_many call leads to the kernel setting up
the action, notifying userspace of its creation, and then tearing it
down. For existing actions, the refcount is still held so they remain
unaffected.

Fortunately due to rtnl_lock serialization requirement, such an action
with refcount == 1 will not be concurrently deleted by anything else, at
best CLS API can move its refcount up and down by binding to it after it
has been published from tcf_idr_insert_many. Since refcount is atleast
one until put_many call, CLS API cannot delete it. Also __tcf_action_put
release path already ensures deterministic outcome (either new action
will be created or existing action will be reused in case CLS API tries
to bind to action concurrently) due to idr lock serialization.

We fix this by making refcount of newly created actions as 2 in ACT API
replace mode. A relaxed store will suffice as visibility is ensured only
after the tcf_idr_insert_many call.

Note that in case of creation or overwriting using CLS API only (i.e.
bind = 1), overwriting existing action object is not allowed, and any
such request is silently ignored (without error).

The refcount bump that occurs in tcf_idr_check_alloc call there for
existing action will pair with tcf_exts_destroy call made from the
owner module for the same action. In case of action creation, there
is no existing action, so no tcf_exts_destroy callback happens.

This means no code changes for CLS API.

Fixes: cae422f3 ("net: sched: use reference counting action init")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling ncsi_stop_channel_monitor from channel_monitor is a guaranteed
deadlock on SMP because stop calls del_timer_sync on the timer that
invoked channel_monitor as its timer function.

Recognise the inherent race of marking the monitor disabled before
deleting the timer by just returning if enable was cleared.  After
a timeout (the default case -- reset to START when response received)
just mark the monitor.enabled false.

If the channel has an entry on the channel_queue list, or if the
state is not ACTIVE or INACTIVE, then warn and mark the timer stopped
and don't restart, as the locking is broken somehow.

Fixes: 0795fb20 ("net/ncsi: Stop monitor if channel times out or is inactive")
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In nfp_bpf_ctrl_msg_rx, if
nfp_ccm_get_type(skb) == NFP_CCM_TYPE_BPF_BPF_EVENT is true, the skb
will be freed. But the skb is still used by nfp_ccm_rx(&bpf->ccm, skb).

My patch adds a return when the skb was freed.

Fixes: bcf0cafa ("nfp: split out common control message handling code")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2021-03-29

This series contains updates to ice driver only.

Ani does not fail on link/PHY errors during probe as this is not a fatal
error to prevent the user from remedying the problem. He also corrects
checking Wake on LAN support to be port number, not PF ID.

Fabio increases the AdminQ timeout as some commands can take longer than
the current value.

Chinh fixes iSCSI to use be able to use port 860 by using information
from DCBx and other QoS configuration info.

Krzysztof fixes a possible race between ice_open() and ice_stop().

Bruce corrects the ordering of arguments in a memory allocation call.

Dave removes DCBNL device reset bit which is blocking changes coming
from DCBNL interface.

Jacek adds error handling for filter allocation failure.

Robert ensures memory is freed if VSI filter list issues are
encountered.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This binding file uses $ref: ethernet-controller.yaml# so it's required
to use "unevaluatedProperties" (instead of "additionalProperties") to
make Ethernet properties validate.

Fixes: f08b5cf1 ("dt-bindings: net: bcm4908-enet: include ethernet-controller.yaml")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

The correct property name is "nvmem-cell-names". This is what:
1. Was originally documented in the ethernet.txt
2. Is used in DTS files
3. Matches standard syntax for phandles
4. Linux net subsystem checks for

Fixes: 9d3de3c5 ("dt-bindings: net: Add YAML schemas for the generic Ethernet options")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the if(skb_peek(arrvq) == skb) branch, it calls __skb_dequeue(arrvq) to get
the skb by skb = skb_peek(arrvq). Then __skb_dequeue() unlinks the skb from arrvq
and returns the skb which equals to skb_peek(arrvq). After __skb_dequeue(arrvq)
finished, the skb is freed by kfree_skb(__skb_dequeue(arrvq)) in the first time.

Unfortunately, the same skb is freed in the second time by kfree_skb(skb) after
the branch completed.

My patch removes kfree_skb() in the if(skb_peek(arrvq) == skb) branch, because
this skb will be freed by kfree_skb(skb) finally.

Fixes: cb1b7280 ("tipc: eliminate race condition at multicast reception")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Accessing SGE_QBASE_MAP[0-3] and SGE_QBASE_INDEX registers can lead
to SGE missing doorbells under heavy traffic. So, only collect them
when adapter is idle. Also update the regdump range to skip collecting
these registers.

Fixes: 80a95a80 ("cxgb4: collect SGE PF/VF queue map")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If PHY is not available on DSA port (described at devicetree but absent or
failed to detect) then kernel prints warning after 3700 secs:

[ 3707.948771] ------------[ cut here ]------------
[ 3707.948784] Type was not set for devlink port.
[ 3707.948894] WARNING: CPU: 1 PID: 17 at net/core/devlink.c:8097 0xc083f9d8

We should unregister the devlink port as a user port and
re-register it as an unused port before executing "continue" in case of
dsa_port_setup error.

Fixes: 86f8b1c0 ("net: dsa: Do not make user port errors fatal")
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Handle return error code of eth_mac_addr();

Fixes: 3d23a05c ("gianfar: Enable changing mac addr when if up")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In myri10ge_sw_tso, the skb_list_walk_safe macro will set
(curr) = (segs) and (next) = (curr)->next. If status!=0 is true,
the memory pointed by curr and segs will be free by dev_kfree_skb_any(curr).
But later, the segs is used by segs = segs->next and causes a uaf.

As (next) = (curr)->next, my patch replaces seg->next to next.

Fixes: 536577f3 ("net: myri10ge: use skb_list_walk_safe helper for gso segments")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add MAINTAINERS entry for Qualcomm IPC Router (QRTR) driver.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-5.12-20210329' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2021-03-29

this is a pull request of 3 patches for net/master.

The two patch are by Oliver Hartkopp. He fixes length check in the
proto_ops::getname callback for the CAN RAW, BCM and ISOTP protocols,
which were broken by the introduction of the J1939 protocol.

The last patch is by me and fixes the a BUILD_BUG_ON() check which
triggers on ARCH=arm with CONFIG_AEABI unset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: spectrum: Fix ECN marking in tunnel decapsulation

Patch #1 fixes a discrepancy between the software and hardware data
paths with regards to ECN marking after decapsulation. See the changelog
for a detailed description.

Patch #2 extends the ECN decap test to cover all possible combinations
of inner and outer ECN markings. The test passes over both data paths.

v2:
* Only set ECT(1) if inner is ECT(0)
* Introduce a new helper to determine inner ECN. Share it between NVE
  and IP-in-IP tunnels
* Extend the selftest
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that all possible combinations of inner and outer ECN bits result
in the correct inner ECN marking according to RFC 6040 4.2.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cited commit changed the behavior of the software data path with regards
to the ECN marking of decapsulated packets. However, the commit did not
change other callers of __INET_ECN_decapsulate(), namely mlxsw. The
driver is using the function in order to ensure that the hardware and
software data paths act the same with regards to the ECN marking of
decapsulated packets.

The discrepancy was uncovered by commit 5aa3c334 ("selftests:
forwarding: vxlan_bridge_1d: Fix vxlan ecn decapsulate value") that
aligned the selftest to the new behavior. Without this patch the
selftest passes when used with veth pairs, but fails when used with
mlxsw netdevs.

Fix this by instructing the device to propagate the ECT(1) mark from the
outer header to the inner header when the inner header is ECT(0), for
both NVE and IP-in-IP tunnels.

A helper is added in order not to duplicate the code between both tunnel
types.

Fixes: b7237487 ("tunnel: Propagate ECT(1) when decapsulating as recommended by RFC6040")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When ice_remove_vsi_lkup_fltr is called, by calling
ice_add_to_vsi_fltr_list local copy of vsi filter list
is created. If any issues during creation of vsi filter
list occurs it up for the caller to free already
allocated memory. This patch ensures proper memory
deallocation in these cases.

Fixes: 80d144c9 ("ice: Refactor switch rule management structures and functions")
Signed-off-by: Robert Malz <robertx.malz@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

As per the spec, the WoL control word read from the NVM should be
interpreted as port numbers, and not PF numbers. So when checking
if WoL supported, use the port number instead of the PF ID.

Also, ice_is_wol_supported doesn't really need a pointer to the pf
struct, but just needs a pointer to the hw instance.

Fixes: 769c500d ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Add handling of allocation fault for ice_vsi_list_map_info.

Also *fi should not be NULL pointer, it is a reference to raw
data field, so remove this variable and use the reference
directly.

Fixes: 9daf8208 ("ice: Add support for switch filter programming")
Signed-off-by: Jacek Bułatek <jacekx.bulatek@intel.com>
Co-developed-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The original purpose of the ICE_DCBNL_DEVRESET was to protect
the driver during DCBNL device resets.  But, the flow for
DCBNL device resets now consists of only calls up the stack
such as dev_close() and dev_open() that will result in NDO calls
to the driver.  These will be handled with state changes from the
stack.  Also, there is a problem of the dev_close and dev_open
being blocked by checks for reset in progress also using the
ICE_DCBNL_DEVRESET bit.

Since the ICE_DCBNL_DEVRESET bit is not necessary for protecting
the driver from DCBNL device resets and it is actually blocking
changes coming from the DCBNL interface, remove the bit from the
PF state and don't block driver function based on DCBNL reset in
progress.

Fixes: b94b013e ("ice: Implement DCBNL support")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Fix the order of number of array members and member size parameters in a
*calloc() call.

Fixes: b3c38904 ("ice: avoid unnecessary single-member variable-length structs")
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

There is a possibility of race between ice_open or ice_stop calls
performed by OS and reset handling routine both trying to modify VSI
resources. Observed scenarios:
- reset handler deallocates memory in ice_vsi_free_arrays and ice_open
  tries to access it in ice_vsi_cfg_txq leading to driver crash
- reset handler deallocates memory in ice_vsi_free_arrays and ice_close
  tries to access it in ice_down leading to driver crash
- reset handler clears port scheduler topology and sets port state to
  ICE_SCHED_PORT_STATE_INIT leading to ice_ena_vsi_txq fail in ice_open

To prevent this additional checks in ice_open and ice_stop are
introduced to make sure that OS is not allowed to alter VSI config while
reset is in progress.

Fixes: cdedef59 ("ice: Configure VSIs for Tx/Rx")
Signed-off-by: Krzysztof Goreczny <krzysztof.goreczny@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iSCSI can use both TCP ports 860 and 3260. However, in our current
implementation, the ice_aqc_opc_get_cee_dcb_cfg (0x0A07) AQ command
doesn't provide a way to communicate the protocol port number to the
AQ's caller. Thus, we assume that 3260 is the iSCSI port number at the
AQ's caller layer.

Rely on the dcbx-willing mode, desired QoS and remote QoS configuration to
determine which port number that iSCSI will use.

Fixes: 0ebd3ff1 ("ice: Add code for DCB initialization part 2/4")
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

250 msec timeout is insufficient for some AQ commands. Advice from FW
team was to increase the timeout. Increase to 1 second.

Fixes: 7ec59eea ("ice: Add support for control queues")
Signed-off-by: Fabio Pricoco <fabio.pricoco@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

An incorrect NVM update procedure can result in the driver failing probe.
In this case, the recommended resolution method is to update the NVM
using the right procedure. However, if the driver fails probe, the user
will not be able to update the NVM. So do not fail probe on link/PHY
errors.

Fixes: 1a3571b5 ("ice: restore PHY settings on media insertion")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

In commit ea780056 ("can: add optional DLC element to Classical
CAN frame structure") the struct can_frame::can_dlc was put into an
anonymous union with another u8 variable.

For various reasons some members in struct can_frame and canfd_frame
including the first 8 byes of data are expected to have the same
memory layout. This is enforced by a BUILD_BUG_ON check in af_can.c.

Since the above mentioned commit this check fails on ARM kernels
compiled with the ARM OABI (which means CONFIG_AEABI not set). In this
case -mabi=apcs-gnu is passed to the compiler, which leads to a
structure size boundary of 32, instead of 8 compared to CONFIG_AEABI
enabled. This means the the union in struct can_frame takes 4 bytes
instead of the expected 1.

Rong Chen illustrates the problem with pahole in the ARM OABI case:

| struct can_frame {
|          canid_t                    can_id;               /* 0     4 */
|          union {
|                  __u8               len;                  /* 4     1 */
|                  __u8               can_dlc;              /* 4     1 */
|          };                                               /* 4     4 */
|          __u8                       __pad;                /* 8     1 */
|          __u8                       __res0;               /* 9     1 */
|          __u8                       len8_dlc;             /* 10    1 */
|
|          /* XXX 5 bytes hole, try to pack */
|
|          __u8                       data[8]
| __attribute__((__aligned__(8))); /*    16     8 */
|
|          /* size: 24, cachelines: 1, members: 6 */
|          /* sum members: 19, holes: 1, sum holes: 5 */
|          /* forced alignments: 1, forced holes: 1, sum forced holes: 5 */
|          /* last cacheline: 24 bytes */
| } __attribute__((__aligned__(8)));

Marking the anonymous union as __attribute__((packed)) fixes the
BUILD_BUG_ON problem on these compilers.

Fixes: ea780056 ("can: add optional DLC element to Classical CAN frame structure")
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Rong Chen <rong.a.chen@intel.com>
Link: https://lore.kernel.org/linux-can/2c82ec23-3551-61b5-1bd8-178c3407ee83@hartkopp.net/
Link: https://lore.kernel.org/r/20210325125850.1620-3-socketcan@hartkopp.netSigned-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Since commit f5223e9e ("can: extend sockaddr_can to include j1939
members") the sockaddr_can has been extended in size and a new
CAN_REQUIRED_SIZE macro has been introduced to calculate the protocol
specific needed size.

The ABI for the msg_name and msg_namelen has not been adapted to the
new CAN_REQUIRED_SIZE macro for the other CAN protocols which leads to
a problem when an existing binary reads the (increased) struct
sockaddr_can in msg_name.

Fixes: e057dd3f ("can: add ISO 15765-2:2016 transport protocol")
Reported-by: Richard Weinberger <richard@nod.at>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Link: https://lore.kernel.org/linux-can/1135648123.112255.1616613706554.JavaMail.zimbra@nod.at/T/#t
Link: https://lore.kernel.org/r/20210325125850.1620-2-socketcan@hartkopp.netSigned-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Since commit f5223e9e ("can: extend sockaddr_can to include j1939
members") the sockaddr_can has been extended in size and a new
CAN_REQUIRED_SIZE macro has been introduced to calculate the protocol
specific needed size.

The ABI for the msg_name and msg_namelen has not been adapted to the
new CAN_REQUIRED_SIZE macro for the other CAN protocols which leads to
a problem when an existing binary reads the (increased) struct
sockaddr_can in msg_name.

Fixes: f5223e9e ("can: extend sockaddr_can to include j1939 members")
Reported-by: Richard Weinberger <richard@nod.at>
Tested-by: Richard Weinberger <richard@nod.at>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Link: https://lore.kernel.org/linux-can/1135648123.112255.1616613706554.JavaMail.zimbra@nod.at/T/#t
Link: https://lore.kernel.org/r/20210325125850.1620-1-socketcan@hartkopp.netSigned-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In pvc_xmit, if __skb_pad(skb, pad, false) failed, it will free
the skb in the first time and goto drop. But the same skb is freed
by kfree_skb(skb) in the second time in drop.

Maintaining the original function unchanged, my patch adds a new
label out to avoid the double free if __skb_pad() failed.

Fixes: f5083d0c ("drivers/net/wan/hdlc_fr: Improvements to the code of pvc_xmit")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2021-03-25

This series contains updates to virtchnl header file and i40e driver.

Norbert removes added padding from virtchnl RSS structures as this
causes issues when iterating over the arrays.

Mateusz adds Asym_Pause as supported to allow these settings to be set
as the hardware supports it.

Eryk fixes an issue where encountering a VF reset alongside releasing
VFs could cause a call trace.

Arkadiusz moves TC setup before resource setup as previously it was
possible to enter with a null q_vector causing a kernel oops.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes following syzbot report:

UBSAN: shift-out-of-bounds in ./include/net/red.h:237:23
shift exponent 32 is too large for 32-bit type 'unsigned int'
CPU: 1 PID: 8418 Comm: syz-executor170 Not tainted 5.12.0-rc4-next-20210324-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:79 [inline]
 dump_stack+0x141/0x1d7 lib/dump_stack.c:120
 ubsan_epilogue+0xb/0x5a lib/ubsan.c:148
 __ubsan_handle_shift_out_of_bounds.cold+0xb1/0x181 lib/ubsan.c:327
 red_set_parms include/net/red.h:237 [inline]
 choke_change.cold+0x3c/0xc8 net/sched/sch_choke.c:414
 qdisc_create+0x475/0x12f0 net/sched/sch_api.c:1247
 tc_modify_qdisc+0x4c8/0x1a50 net/sched/sch_api.c:1663
 rtnetlink_rcv_msg+0x44e/0xad0 net/core/rtnetlink.c:5553
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502
 netlink_unicast_kernel net/netlink/af_netlink.c:1312 [inline]
 netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1338
 netlink_sendmsg+0x856/0xd90 net/netlink/af_netlink.c:1927
 sock_sendmsg_nosec net/socket.c:654 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:674
 ____sys_sendmsg+0x6e8/0x810 net/socket.c:2350
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2404
 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2433
 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x43f039
Code: 28 c3 e8 2a 14 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffdfa725168 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000400488 RCX: 000000000043f039
RDX: 0000000000000000 RSI: 0000000020000040 RDI: 0000000000000004
RBP: 0000000000403020 R08: 0000000000400488 R09: 0000000000400488
R10: 0000000000400488 R11: 0000000000000246 R12: 00000000004030b0
R13: 0000000000000000 R14: 00000000004ac018 R15: 0000000000400488

Fixes: 8afa10cb ("net_sched: red: Avoid illegal values")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
net: do not modify the shared tunnel info when PMTU triggers an ICMP reply

The series fixes an issue were a shared ip_tunnel_info is modified when
PMTU triggers an ICMP reply in vxlan and geneve, making following
packets in that flow to have a wrong destination address if the flow
isn't updated. A detailled information is given in each of the two
commits.

This was tested manually with OVS and I ran the PTMU selftests with
kmemleak enabled (all OK, none was skipped).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When the interface is part of a bridge or an Open vSwitch port and a
packet exceed a PMTU estimate, an ICMP reply is sent to the sender. When
using the external mode (collect metadata) the source and destination
addresses are reversed, so that Open vSwitch can match the packet
against an existing (reverse) flow.

But inverting the source and destination addresses in the shared
ip_tunnel_info will make following packets of the flow to use a wrong
destination address (packets will be tunnelled to itself), if the flow
isn't updated. Which happens with Open vSwitch, until the flow times
out.

Fixes this by uncloning the skb's ip_tunnel_info before inverting its
source and destination addresses, so that the modification will only be
made for the PTMU packet, not the following ones.

Fixes: c1a800e8 ("geneve: Support for PMTU discovery on directly bridged links")
Tested-by: Eelco Chaudron <echaudro@redhat.com>
Reviewed-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>