- 27 Jan, 2016 2 commits
-
-
Marcus Cooper authored
The Itead Ibox is a multi board device based on the Allwinner A20 SoC. It contains the A20 Itead Core module and a base board for the external interfaces. The core module comes with 4GB NAND and 1GB DDR RAM. The base board to which the core board is connected provides 3 USB 2.0 Host ports, 1 USB 2.0 OTG, 1 uSD slot, 10/100 Ethernet port, HDMI, IR receiver, SPDIF and a 32-pin GPIO header. This header expands the features of core board by exposing the VGA pins, audio In/Out pins, SATA, SPI, I2C, UARTS, USB-OTG and power. Signed-off-by:
Marcus Cooper <codekipper@gmail.com> Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com>
-
Marcus Cooper authored
Itead have a core module board that can be populated with either an Allwinner A10 or A20 SoC. This patch creates a common dtsi which these boards can use. Signed-off-by:
-
- 24 Jan, 2016 38 commits
-
-
Chen-Yu Tsai authored
mmc2 has a special pin for eMMC hardware reset, which is controllable from the controller. Add the "mmc-cap-hw-reset" property to denote that this controller supports this function, and the pins are actually used. Also increase the signal drive strength for mmc2 pins, for HS-DDR mode support. Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
-
Chen-Yu Tsai authored
mmc2 has a special pin for eMMC hardware reset, which is controllable from the controller. Add the "mmc-cap-hw-reset" property to denote that this controller supports this function, and the pins are actually used. Also increase the signal drive strength for mmc2 pins, for HS-DDR mode support. Signed-off-by:
-
Chen-Yu Tsai authored
mmc2_8bit_pins is used with eMMC chips, which also have a reset pin. The MMC controller also has a reset output that is supported. Signed-off-by:
-
Chen-Yu Tsai authored
mmc2_8bit_pins is used with eMMC chips, which also have a reset pin. The MMC controller also has a reset output that is supported. Signed-off-by:
-
Chen-Yu Tsai authored
According to Allwinner, only mmc3 supports 8 bit DDR transfers for eMMC. Switch to mmc3 for the onboard eMMC, and also assign vqmmc for signal voltage sensing, and "cap-mmc-hw-reset" to denote this instance can use eMMC hardware reset. Signed-off-by:
-
Chen-Yu Tsai authored
mmc2 and mmc3 are available on the same pins, with different mux values. However, only mmc3 supports 8 bit DDR transfer modes. Since preference for mmc3 over mmc2 is due to DDR transfer modes, just set the drive strength to 40mA, which is needed for DDR. This pinmux setting also includes the hardware reset pin for emmc. Signed-off-by:
-
Chen-Yu Tsai authored
sun9i/A80 MMC controllers have a larger FIFO, and the FIFO DMA trigger levels can be increased. Also, the mmc module clock parent has a higher clock rate, and the sample and output delay phases are different. Signed-off-by:
-
Chen-Yu Tsai authored
mmc2 has a special pin for eMMC hardware reset, which is controllable from the controller. Add the "mmc-cap-hw-reset" property to denote that this controller supports this function, and the pins are actually used. Also increase the signal drive strength for mmc2 pins, for HS-DDR mode support. Signed-off-by:
-
Maxime Ripard authored
The current DT doesn't have a phandle to the CPU regulator in the CPU node, which disables the CPU voltage scaling entirely. Add that phandle. Signed-off-by: -
Chen-Yu Tsai authored
Cubietruck Plus is a A83T/H8 based development board. The board has standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet, WiFi, headphone out / mic in, and various GPIO headers. The board also has an EEPROM on i2c0 which holds the MAC address. Signed-off-by:
-
Chen-Yu Tsai authored
The A83T, like previous Allwinner SoCs, has a watchdog as part of its timer block. Add a device node for it. Signed-off-by:
-
Vishnu Patekar authored
A83T timer is compatible with that of earlier SOCs. Just add timer node to enable and re-use it. Signed-off-by:
Vishnu Patekar <vishnupatekar0510@gmail.com> Signed-off-by:
-
Vishnu Patekar authored
H8Homlet Proto v2.0 Board is A83T Dev Board by Allwinner. It has UART, ethernet, USB, HDMI, etc ports on it. A83T patches are tested on this board. It has UART, ethernet, USB, HDMI, etc ports on it. For FEL mode it needs USB A-A(Male) cable. I used uart0 which is multiplexed to microsd pins PF2 and PF4. Enabled UART0 Header(PB9, PB10 pins). Signed-off-by:
-
Vishnu Patekar authored
Allwinner A83T is new octa-core cortex-a7 SOC. This adds the basic dtsi, the clocks differs from earlier sun8i SOCs. Signed-off-by:
-
Hans de Goede authored
Add a node describing the focaltech ft5306de4 touchscreen found on inet97fv2 tablets. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Hans de Goede authored
Add a node describing the focaltech ft5306de4 touchscreen found on chuwi-v7-cw0825 tablets. Signed-off-by:
-
Hans de Goede authored
Add a node describing the focaltech ft5406ee8 touchscreen found on inet-9f-rev03 / qware qw tb-g100 tablets. Signed-off-by:
-
Linus Torvalds authored
-
git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds authored
Pull MIPS updates from Ralf Baechle: "This is the main pull request for MIPS for 4.5 plus some 4.4 fixes. The executive summary: - ATH79 platform improvments, use DT bindings for the ATH79 USB PHY. - Avoid useless rebuilds for zboot. - jz4780: Add NEMC, BCH and NAND device tree nodes - Initial support for the MicroChip's DT platform. As all the device drivers are missing this is still of limited use. - Some Loongson3 cleanups. - The unavoidable whitespace polishing. - Reduce clock skew when synchronizing the CPU cycle counters on CPU startup. - Add MIPS R6 fixes. - Lots of cleanups across arch/mips as fallout from KVM. - Lots of minor fixes and changes for IEEE 754-2008 support to the FPU emulator / fp-assist software. - Minor Ralink, BCM47xx and bcm963xx platform support improvments. - Support SMP on BCM63168" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits) MIPS: zboot: Add support for serial debug using the PROM MIPS: zboot: Avoid useless rebuilds MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function MIPS: bcm963xx: Update bcm_tag field image_sequence MIPS: bcm963xx: Move extended flash address to bcm_tag header file MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure MIPS: bcm63xx: nvram: Use nvram structure definition from header file MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure MAINTAINERS: Add KVM for MIPS entry MIPS: KVM: Add missing newline to kvm_err() MIPS: Move KVM specific opcodes into asm/inst.h MIPS: KVM: Use cacheops.h definitions MIPS: Break down cacheops.h definitions MIPS: Use EXCCODE_ constants with set_except_vector() MIPS: Update trap codes MIPS: Move Cause.ExcCode trap codes to mipsregs.h MIPS: KVM: Make kvm_mips_{init,exit}() static MIPS: KVM: Refactor added offsetof()s MIPS: KVM: Convert EXPORT_SYMBOL to _GPL ... -
Linus Torvalds authored
Merge tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86 Pull x86 platform driver updates from Darren Hart: "Emergency travel prevented me from completing my final testing on this until today. Nothing here that couldn't wait until RC1 fixes, but I thought it best to get it out sooner rather than later as it does contain a build warning fix. Summary: A build warning fix, MAINTAINERS cleanup, and a new DMI quirk: ideapad-laptop: - Add Lenovo Yoga 700 to no_hw_rfkill dmi list MAINTAINERS: - Combine multiple telemetry entries intel_telemetry_debugfs: - Fix unused warnings in telemetry debugfs" * tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list MAINTAINERS: Combine multiple telemetry entries intel_telemetry_debugfs: Fix unused warnings in telemetry debugfs
-
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linuxLinus Torvalds authored
Pull thermal management updates from Zhang Rui: "The top merge commit was re-generated yesterday because two topic branches were dropped from this pull request in the last minute due to some unaddressed comments. All the other material has been in linux-next for quite a while. Specifics: - Enhance thermal core to handle unexpected device cooling states after fresh boot and system resume. From Zhang Rui and Chen Yu. - Several fixes and cleanups on Rockchip and RCAR thermal drivers. From Caesar Wang and Kuninori Morimoto. - Add Broxton support for Intel processor thermal reporting device driver. From Amy Wiles" * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: thermal: trip_point_temp_store() calls thermal_zone_device_update() thermal: rcar: rcar_thermal_get_temp() return error if strange temp thermal: rcar: check irq possibility in rcar_thermal_irq_xxx() thermal: rcar: check every rcar_thermal_update_temp() return value thermal: rcar: move rcar_thermal_dt_ids to upside thermal: rockchip: Support the RK3399 SoCs in thermal driver thermal: rockchip: Support the RK3228 SoCs in thermal driver dt-bindings: rockchip-thermal: Support the RK3228/RK3399 SoCs compatible thermal: rockchip: fix a trivial typo Thermal: Enable Broxton SoC thermal reporting device thermal: constify pch_dev_ops structure Thermal: do thermal zone update after a cooling device registered Thermal: handle thermal zone device properly during system sleep Thermal: initialize thermal zone device correctly -
git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fsLinus Torvalds authored
Pull 9p updates from Eric Van Hensbergen: "Sorry for the last minute pull request, there's was a change that didn't get pulled into for-next until two weeks ago and I wanted to give it some bake time. Summary: Rework and error handling fixes, primarily in the fscatch and fd transports" * tag 'for-linus-4.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs: fs/9p: use fscache mutex rather than spinlock 9p: trans_fd, bail out if recv fcall if missing 9p: trans_fd, read rework to use p9_parse_header net/9p: Add device name details on error
-
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-clientLinus Torvalds authored
Pull Ceph updates from Sage Weil: "The two main changes are aio support in CephFS, and a series that fixes several issues in the authentication key timeout/renewal code. On top of that are a variety of cleanups and minor bug fixes" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: libceph: remove outdated comment libceph: kill off ceph_x_ticket_handler::validity libceph: invalidate AUTH in addition to a service ticket libceph: fix authorizer invalidation, take 2 libceph: clear messenger auth_retry flag if we fault libceph: fix ceph_msg_revoke() libceph: use list_for_each_entry_safe ceph: use i_size_{read,write} to get/set i_size ceph: re-send AIO write request when getting -EOLDSNAP error ceph: Asynchronous IO support ceph: Avoid to propagate the invalid page point ceph: fix double page_unlock() in page_mkwrite() rbd: delete an unnecessary check before rbd_dev_destroy() libceph: use list_next_entry instead of list_entry_next ceph: ceph_frag_contains_value can be boolean ceph: remove unused functions in ceph_frag.h
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull SMB3 fixes from Steve French: "A collection of CIFS/SMB3 fixes. It includes a couple bug fixes, a few for improved debugging of cifs.ko and some improvements to the way cifs does key generation. I do have some additional bug fixes I expect in the next week or two (to address a problem found by xfstest, and some fixes for SMB3.11 dialect, and a couple patches that just came in yesterday that I am reviewing)" * 'for-next' of git://git.samba.org/sfrench/cifs-2.6: cifs_dbg() outputs an uninitialized buffer in cifs_readdir() cifs: fix race between call_async() and reconnect() Prepare for encryption support (first part). Add decryption and encryption key generation. Thanks to Metze for helping with this. cifs: Allow using O_DIRECT with cache=loose cifs: Make echo interval tunable cifs: Check uniqueid for SMB2+ and return -ESTALE if necessary Print IP address of unresponsive server cifs: Ratelimit kernel log messages
-
Josh Boyer authored
Like the Yoga 900 models the Lenovo Yoga 700 does not have a hw rfkill switch, and trying to read the hw rfkill switch through the ideapad module causes it to always reported blocking breaking wifi. This commit adds the Lenovo Yoga 700 to the no_hw_rfkill dmi list, fixing the wifi breakage. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1295272 Tested-by: <dinyar.rabady+spam@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by:
Darren Hart <dvhart@linux.intel.com>
-
Souvik Kumar Chakravarty authored
This patch combines all the telemetry file entries in MAINTAINERS via wildcard. Signed-off-by:
Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com> Signed-off-by:
-
Souvik Kumar Chakravarty authored
This patch fixes compile time warnings when CONFIG_PM_SLEEP is undefined. In this case sleep related counters are unused. Signed-off-by:
-
Christoph Lameter authored
If we detect that there is nothing to do just set the flag and do not check if it was already set before. Races really do not matter. If the flag is set by any code then the shepherd will start dealing with the situation and reenable the vmstat workers when necessary again. Since commit 0eb77e98 ("vmstat: make vmstat_updater deferrable again and shut down on idle") quiet_vmstat might update cpu_stat_off and mark a particular cpu to be handled by vmstat_shepherd. This might trigger a VM_BUG_ON in vmstat_update because the work item might have been sleeping during the idle period and see the cpu_stat_off updated after the wake up. The VM_BUG_ON is therefore misleading and no more appropriate. Moreover it doesn't really suite any protection from real bugs because vmstat_shepherd will simply reschedule the vmstat_work anytime it sees a particular cpu set or vmstat_update would do the same from the worker context directly. Even when the two would race the result wouldn't be incorrect as the counters update is fully idempotent. Reported-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
Christoph Lameter <cl@linux.com> Acked-by:
Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Ralf Baechle authored
-
Alban Bedel authored
As most platforms implement the PROM serial interface prom_putchar() add a simple bridge to allow re-using this code for zboot. Signed-off-by:
Alban Bedel <albeu@free.fr> Cc: Alex Smith <alex.smith@imgtec.com> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: Wu Zhangjin <wuzhangjin@gmail.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11811/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org>
-
Alban Bedel authored
Add dummy.o to the targets list, and fill targets automatically from $(vmlinuzobjs) to avoid having to maintain two lists. When building with XZ compression copy ashldi3.c to the build directory to use a different object file for the kernel and zboot. Without this the same object file need to be build with different flags which cause a rebuild at every run. Signed-off-by:
-
Florian Fainelli authored
Allow BMIPS_GENERIC supported platforms to build GPIO controller drivers. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
Dragan Stancevic <dragan.stancevic@gmail.com> Cc: cernekee@gmail.com Cc: jaedon.shin@gmail.com Cc: gregory.0xf0@gmail.com Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12019/Signed-off-by:
-
Simon Arlott authored
Remove bcm63xx_nvram_get_psi_size() as it now has no users. Signed-off-by:
Simon Arlott <simon@fire.lp0.eu> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Jonas Gorski <jogo@openwrt.org> Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org> Cc: MIPS Mailing List <linux-mips@linux-mips.org> Cc: MTD Maling List <linux-mtd@lists.infradead.org> Patchwork: https://patchwork.linux-mips.org/patch/11836/Signed-off-by:
-
Simon Arlott authored
The "dual_image" and "inactive_flag" fields should be merged into a single "image_sequence" field. Signed-off-by:
-
Simon Arlott authored
The extended flash address needs to be subtracted from bcm_tag flash image offsets. Move this value to the bcm_tag header file. Renamed define name to consistently use bcm963xx for flash layout which should be considered a property of the board and not the SoC (i.e. bcm63xx could theoretically be used on a board without CFE or any flash). Signed-off-by:
-
Simon Arlott authored
Move Broadcom BCM963xx image tag data structure to include/linux/ so that drivers outside of mach-bcm63xx can use it. Signed-off-by:
-
Simon Arlott authored
Use the common definition of the nvram structure from the header file include/linux/bcm963xx_nvram.h instead of maintaining a separate copy. Read the version 5 size of nvram data from memory and then call the new checksum verification function from the header file. Signed-off-by:
-
Simon Arlott authored
Broadcom BCM963xx boards have multiple nvram variants across different SoCs with additional checksum fields added whenever the size of the nvram was extended. Add this structure as a header file so that multiple drivers can use it. Signed-off-by:
-
